User Manual for RF module/Receiver TX (RF module) RX (Receiver) Be sure to read a user manual before its usage Product Overviews When it comes to the existing RF module/Receiver for PC, it is impossible to use the same frequency at the same time due to the interference between frequencies, which resulting in low reuse of frequency. Also the said product has lots of problems such as vulnerability to outside signals and multi users inconvenience for spontaneous use. This product employs digital communication method in 2.4GHz of ISM band to take care of the said interference between frequencies and also fast transmission rate and fine resolution for flexible operation. It is designed so that unique ID would be assigned for each RF module and related Receiver and RF module should communicate mutually using the said ID for ID setting. In other words, Receiver has only ID of RF module finally set and get only data transmitted from the said RF. Also for interference between wireless frequencies, it check-ups RF environments to acquire stable communication on ID setting that in turn be sure to configure the most superior channel as communication one. For the said features, RF module and Receiver can perform related functions without any data loss even for external interference. Cautions and safety Safety Be sure to read User manual before its usage Do not attempt to dismantle product. Otherwise it may result in malfunction For RF module and Receiver, it should be attached after turn off power (control and model) After connecting RF module to control, be sure to position controls throttle level on stop and turn on control power and Receiver one in order. Caution When turning off power, be sure to turn off engine or motor and then receiver power and control one in order. In case of wrong operation, there may be a danger of spontaneous miss-operation. Be sure to take an operation test between RF module and Receiver before its control Be sure to operate each channel for normal operation. If there is any problem, never attempt to operate it. For Receiver attachment, please make a dust-proof device from Styrofoam. Especially dust-proof procedure may be recommended for engine part Do not attempt to modify antennas length voluntarily Please make sure that antenna should not be covered with airframes internal section or lid with metal paint or carbon fiber. Otherwise it may decrease radio waves efficiency. Do not use any combination of Radiopost RF module and other vendors Receiver or reversely. We never hold any responsibility for any damages from any combination with other vendors receiver or RF module. Designation of each part by model Futaba/Hiltec controller JR controller RF module Receiver Product Features Superior stability with 2.4GHz band 2.4GHz auto channel configuration (no crystal required) Confirmation of ID-setting with Sound could be possible Excellent binding speed RF module As RF modules antenna is internal type, it gives convenience when attaching a stand on a controller. Radipost RF modules antenna gives high efficiency (7dBi) compared with the existing antennas efficiency (2-3dBi) Radipost RF module can communicate with Radiopost Receiver at all channels. Receiver It may be strong and has wide range of operation and good durability. It is a high sensitive receiver not interfered with mixed modulation and inter-modulation It employs stable top-notch digital technology As it adopts digital method with MCU, It is possible to operate stably It is a universal type that may be used under optimal conditions for helicopter, glider, airplane, vehicles, etc. As it can recognize only users RF module with advanced set, it is possible to be out of No Control situation For worst circumstance, it can prevent dangers with Fail Safe function. (only for RP24RS8D) LED Display RF module When you apply power at the first purchase, LED may stay in red When you press ID-setting button, ID-setting mode displays and LED may blinking in red When ID-setting completes, LED turns to green and stay in that color When you apply power to RF module only without Receiver after pairing, it may start to search for Receiver and LED may blink in green. 1: Red Lamp (on) 2: Red Lamp (blink) 3: Green Lamp (on) 4: Green Lamp (blink) 5: Green Lamp (blink) 6: Red Lamp (blink) 7: Green Lamp (on) 8: Red Lamp (blink) How to use Be sure to select RF module suitable for controller and confirm connectors position and assemble it For Receiver, be sure to confirm polarity of servo and battery before connecting them properly. When you connect RF module to controller and turn it on, you can hear a sound of pi three times and LED turn on and remain in red Be sure to apply power to Receiver When you apply power to Receiver, white LED on Receiver is blinking When you press ID-setting button of RF module for a second, it enters into ID-setting and red LED of RF module is blinking When you press ID-setting button of Receiver for a second, it enters into ID-setting and red LED of RF module is blinking When ID-setting of RF module and Receiver completes, RF modules LED turns to green. When you can hear a sound of pi two times, it indicates that ID-setting completes. Be sure to move the lever of controller and confirm operating status of servo finally. Fail Safe (RP24RA8D model only) This is a function that move servo to pre-set position against radio disturbance during its flight If you place a controller to neutral position and turn throttle into idle or motor-stop status for Fail Safe configuration and the said function works due to the receive interruption, servo may move to pre-set position till signal would sensed for minimizing the destruction of air-frame. How to set up Fail Safe How to turn on Fail Safe Be sure to turn power of RF module and Receiver in order and move a controller to confirm operating status of servo and Paring. Be sure to operate a controller to move servo to Fail Safe position When you press Fail Safe button for 3 seconds, red led is flickering for Fail Safe mode How to turn off When you press Fail Safe button for 3 seconds, red led is flickering and Fail Safe mode is disabled. When you attempt to set up Fail Safe with a Receiver connected to a device, be sure to turn engine power channel into hold or power source should be disconnected. Specifications Controllers compatible This product is compatible for controller supporting PPM mode Futaba FF7A, FF9, 10C (Airplane/Helicopter) Mega Tech 3PM-FS, 3PK (Vehicles) Hiltec OPTIC 6, ECLIPSE (Airplane/Helicopter) Aggressor CRX, Aggressor SRX, Eclipse Procar (Vehicles) JR 9X LIMITED, 10X (Airplane/Helicopter) Product Warranty 1. For products warranty period, it is one year from a date of its purchase. If there is any problem under normal use within the said period, we have to repair with no charge. 2. If the following things occur within warranty period, you may take a charge service Malfunction caused by users careless handling Users dismantle, repair, alteration at his (or her) own will Malfunction caused by other repair center or personnel than our service technician or designated after-sales service center Malfunction caused by natural calamities Consumption goods replacement if there is no information such as date of purchase, customer name, store name or such information would be modified by customer voluntarily 3. For any responsibility related with this product, it should be limited to its repair or replacement. 4. When there is any problem for product, please contact with related store or call the following contact address Model RF module RP24TD9/RP24TD9J Receiver RP24RA5D/RP24RA60/RP24RA8D Date of Purchase Warranty Period: 12 months Purchasing store Telephone from a date of purchase Purchase Price:
Others:
Customer Name Address Telephone About After-sales service If there is malfunction or any problem, please stop its operation and contact with purchase store or our headquarter for after-sales service Customer supporting center: 080-080-6066 (09:00-18:00: Business day) Nextlink Address: Chungangindus 2nd 701#, 144-5, Sang-daewon-dong, Chungwon-gu, Sungnam city, Kyunggi-do www.rcenjoy.com
* FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment is a handheld device and should be maintained with a minimum safety distance of 20cm from the antenna. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.