FCC ID: 2ANH5RC-CC1312R-915 Transceiver Module

 

RC-CC1312R-XXX

RC-CC1101-SPI-434

RC-CC1312R-XXX-H

Radio

ontrolli

Wireless Modules

Ultra Low Power sub 1GHz

Multichannels Radio Transceiver

The RC-CC1312R-XXX module is based on Texas Instruments

CC1312R1F3RGZ component. This device combines a flexible,

very low power RF transceiver with a powerful 48 MHz ARM Cortex

M4F CPU in a platform supporting multiple physical layers and RF

standard. This device is pin to pi compatible with the module

RC-CC1310-XXX.

Module Information :

RC-CC1312R - XXX

Frequency

434=434MHz

868=868MHz

915=915MHz

Sub-1Ghz technology is becoming one of the chief driving forces behind the Internet of Things

(Iot), in particular this type of module is ideal for this applications basically for the following

reasons :

Ultra low power consumption, the consumption of this device is 5.5mA when receiving and

23.5mA when transmitting at +14dBm (13.4mA at +10dBm) in sleep mode the consumption is

0.6

(microamps).

µA

Long range operations, the sensitivity parameter is -110dBm at data rates of 50 kbps and down

to -124dBm when the data rate is 0.625kbps.

Interference from other wireless communications can be overcome with 90dB of blocking.

The RF output power levels can reach up to +14dBm.

All this ensure a robust signaling for long range communications.

SimpleLink-Easylink c

the long-range connectivity with low power consumption on the Internet of Things projects (IoT).

ompatibility,ultra-low power platform designed (from TI) to easily implement

TI-15.4 Stack, IEEE802.15.4e/g Standard Based Star Networking Software Designed for long

range & robust star networks

6LoWPAN

compatibility with mesh network stack for Contiki.

Applications :

Feature :

- Low-Power Wireless Systems

- IEEE 802.15.4g mode switch support

- Smart Grid and Automatic Meter Reading

- Ultra Low consumption technology

- Home and Building Automation

- Powerful ARM Cortex M4

- Wireless Sensor Network

- Supported by the open platform Contiki 6LoWPAN.

- 6LoWPAN systems

- Very Small size

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 1 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1101-SPI-434

RC-CC1312R-XXX-H

Technical Characteristics

Radio

ontrolli

Wireless Modules

RC-CC1312R-XXX

Parameter

Operating Voltage

Supply Current RX Mode

Supply Current TX Mode +10dBm

Supply Current TX Mode +14dBm

Supply Current Standby Mode

Supply Current Shut Down Mode

Operative Frequency

Frequency Error

RF Power Output 50ohm (*)

RF Sensibility 50kbps

RF Sensibility Long Range Mode 625bps

Data Rate (*)

Operative Temperature

(*) Programmable parameter.

MICROCONTROLLER:

- Powerul 48MHz ARM Cortex - M4F Processor

- 352KB of in-system Programmable Flash

- 256KB of ROM for protocol and library function

- 8KB of SRAM for Cache

- 80KB of Ultralow Leakege SRAM

- Support Over-the-Air Upgrade (OTA)

Symbol

Min.

1.8

Max.

3.8

Units

VDC

mA

mA

mA

µA

nA

MHz

ppm

dBm

dBm

Mbit/s

°C

Typ.

3.00

5.80

13.40

24.90

0,85

150

±10

-110.0

-121.0

433/868/915

VCC

lCRX

l

CTX1

l

CTX2

lC

lCSTB

lCSHU

F

of

F

pp

Poo

S d

SLR

DCC

TLR

-10.0

+14.0

dBm

0,01

-30

4.0

+75

Development Tools and Software from TI

– CC1312R LaunchPad™ Development Kit

– SimpleLink™ CC13X2-CC26X2 Software

Development Kit

– SmartRF™ Studio for simple radio configuration

– Sensor Controller Studio for building low-power

sensing applications

For more information and details, please refer to the CC1312R Texas Instruments datasheet.

Block Diagram

Antenna

Connector

Filter

+

RF

Matching

32KHz

crystal

48MHz

crystal

CC1312R1F3RGZ

(SOC)

Reset

JTAG

GPIO

(n.30)

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 2 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1312R-XXX-H

Reference Schematics

Radio

ontrolli

Wireless Modules

1

2

3

4

5

6

7

8

9

10

11

12

13

GND

DIO-1

DIO-2

DIO-3

DIO-4

DIO-5

DIO-6

DIO-7

GND

VDD

DIO-8

DIO-9

DIO-10

VDD

C1

106

DIO-30

DIO-29

DIO-28

DIO-27

DIO-26

DIO-25

DIO-24

DIO-23

RESET

DIO-22

DIO-21

DIO-20

DIO-19

36

35

??

34

33

32

31

30

29

28

27

26

25

24

RESET N

RC-CC1312R-XXX

O

D

T

-

G

A

T

J

/

6

1

-

O

D

I

I

D

T

-

G

A

T

J

/

7

1

-

O

D

I

8

1

-

O

D

I

C

S

M

T

-

G

A

T

J

C

K

C

T

-

G

A

T

J

1

1

-

O

D

I

2

1

-

O

D

I

3

1

-

O

D

I

4

1

-

O

D

I

5

1

-

O

D

I

4

1

5

1

6

1

7

1

8

1

9

1

0

2

1

2

2

2

3

2

0

D

T

-

G

A

T

J

/

6

1

-

O

D

I

I

D

T

-

G

A

T

J

/

7

1

-

O

D

I

C

S

M

T

-

G

A

T

J

C

K

C

T

-

G

A

T

J

For cJTAG

VDD

GND

RESET N

JTAG-TMSC

JTAG-TCKC

For JTAG

VDD

GND

RESET N

JTAG-TDI

JTAG-TDO

JTAG-TMSC

JTAG-TCKC

Mechanical Dimension

1.27mm

15mm

Antenna UFL

Antenna Pad

8

3

9

3

7

3

Antenna hole

RC-CC1312R-XXX

1

2

3

4

5

6

7

8

9

0

1

1

1

2

1

3

1

6

3

5

3

4

3

3

3

2

3

1

3

0

3

9

2

8

2

7

2

6

2

5

2

4

2

22mm

4

1

5

1

6

1

7

1

8

1

9

1

0

2

1

2

2

2

3

2

(2.50 mm)

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 3 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1312R-XXX-H

Radio

ontrolli

Wireless Modules

Terminal description RC-CC1312R-XXX

Antenna UFL

Antenna Pad

8

3

9

3

7

3

Antenna hole

RC-CC1312R-XXX

1

2

3

4

5

6

7

8

9

0

1

1

1

2

1

3

1

6

3

5

3

4

3

3

3

2

3

1

3

0

3

9

2

8

2

7

2

6

2

5

2

4

2

JTAG-TMSC

JTAG-TCKC

JTAG TMSC, High drive capability

JTAG TCKC

GPIO,JTAG -TDO, High drive capability

GPIO,JTAG-TDI, High drive capability

4

1

5

1

6

1

7

1

8

1

9

1

0

2

1

2

2

2

3

2

Pin out device

GPIO

GPIO, High drive capability

GPIO, High drive capability

GPIO, High drive capability

Pads Name

Description

Ground

GPIO

GPIO

GPIO

Ground

Power

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GPIO

GND

DIO-1

DIO-2

DIO-3

DIO-4

DIO-5

DIO-6

DIO-7

GND

VDD

DIO-8

DIO-9

DIO-10

DIO-11

DIO-12

DIO-13

DIO-14

DIO-15

DIO-16

DIO-17

DIO-18

DIO-19

DIO-20

DIO-21

DIO-22

RESET-N

DIO-23

DIO-24

DIO-25

DIO-27

DIO-28

DIO-29

DIO-30

GND

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

RESET, (Active low ,No internal pull up)

GPIO, Analog capability

DIO-26

GPIO, Analog capability

GPIO, Analog capability

GPIO, Analog capability

GPIO, Analog capability

GPIO, Analog capability

GPIO, Analog capability

GPIO, Analog capability

Ground

Antenna

GND

Antenna PAD

Ground

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 4 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1101-SPI-434

RC-CC1312R-XXX-H

Antenna Connection

Radio

ontrolli

Wireless Modules

0 ohm chip selector

UFL connector

Antenna hole connector

Antenna pad connector

Type of Antenna connection

RC-CC1313R-XXX-H

RC-CC1312R-XXX

- Without UFL Connector

- Resistor direct on pcb antenna (hole

and pad)

- With UFL Connector

- Resistor direct on the UFL connector

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 5 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1101-SPI-434

RC-CC1312R-XXX-H

RC-CC1312R-XXX Adapter board

Radio

ontrolli

Wireless Modules

To make immediate usable the RC-CC1312R-XXX module with TI development systems has

been realized the following board adapter.

Adapter board front

Adapter board rear

SMART RF06 Evaluation board (TI)

RC-CC1310-DK Evaluation kit

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 6 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1101-SPI-434

RC-CC1312R-XXX-H

FCC Statement (915MHz version) :

Radio

ontrolli

Wireless Modules

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could

void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

2.2 FCC rules

CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular

transmitter.

2.3 operational use conditions

This module is stand-alone modular. If the end product will involve the Multiple simultaneously

transmitting condition or different operational conditions for a stand-alone modular transmitter in a

host, host manufacturer have to consult with module manufacturer for the installation method in end

system.

2.4 Limited module procedures

Not applicable

2.5 Trace antenna designs

Not applicable

2.6 RF exposure considerations

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator and your body.

2.7 Antennas

This radio transmitter FCCID: 2ANH5RC-CC1312R-915 has been approved by Federal

Communications Commission to operate with the antenna types listed below, with the maximum

permissible gain indicated. Antenna types not included in this list that have a gain greater than the

maximum gain indicated for any type listed are strictly prohibited for use with this device.

2.8 Label and compliance information

The final end product must be labeled in a visible area with the following "Contains FCC

ID:2ANH5RC-CC1312R-915".

2.9 Information on test modes and additional testing requirements

Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the

transmitter when the module is installed in the host.

2.10 Additional testing, Part 15 Subpart B disclaimer

Host manufacturer is responsible for compliance of the host system with module installed with all

other applicable requirements for the system such as Part 15 B.

FCC ID : 2ANH5RC-CC1312R-915

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 7 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1101-SPI-434

RC-CC1312R-XXX-H

Recommended PCB Layout

Radio

ontrolli

Wireless Modules

0.26

2.20

5.08

2.10

Ø0.60

0

2

.

1

15.24

23.00

1.27

1.40

0.70

1.60

0.70

1.77

0.23

1.27

11.43

16.0

Recommended Reflow Profile for Lead Free Solder

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 8 / 9

Rev 1.3

 RC-CC1312R-XXX

RC-CC1101-SPI-434

RC-CC1312R-XXX-H

REEL DIMENSIONS

Radio

ontrolli

Wireless Modules

Reel Diameter

(330mm)

Reel Width

(45mm)

TAPE DIMENSIONS

15.5mm

± 0.10mm

23.0mm

± 0.10mm

3.5mm

± 0.10mm

44.0mm

± 0.30mm

20.0mm

± 0.10mm

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for

any possible lack or inaccuracy of the data and reserves the right to change in whole

or in part these information without notice.

www.radiocontrolli.com

Pag. 9 / 9

Rev 1.3



 

 

 

 

 

 

 

 

 

 

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ANH5RC-CC1312R-915 LABEL AND LOCATION FCC ID: 2ANH5RC-CC1312R-915 Size: L1.5cm*W1.2cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

 

 

Radiocontrolli SRL Agent Authorization Company: Radiocontrolli SRL Address: Via Carditello 10, P.co Nuovo Villaggio 6 81050 San Tammaro -CE Italy Product Name: Transceiver Module Trade Mark: Radiocontrolli Model Number: RC-CC1312R-915 FCC ID: 2ANH5RC-CC1312R-915 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: 2021-06-30 Signature:

Name:

Antonio Di Paola Title:

CEO Company: Radiocontrolli SRL

 

 

Radiocontrolli SRL

Modular Transmitter Approval Request

Federal Communications Commission

Equipment Authorization Branch

7435 Oakland Mills Road

Columbia, MD 21046

Company name: Radiocontrolli SRL

FCC ID: 2ANH5RC-CC1312R-915

Gentlemen,

In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 ‘Module

Certification Guide v01r04’. FCC ID 2ANH5RC-CC1312R-915 has been examined against the

following requirements.

Explanation from Grantee

(do not write yes/no, but explain why product

complies/how it is achieved)

Yes, EUT has the radio frequency circuitry

shielded.

Yes. The module can use the original

antenna or other antennas with lower gain.

Requirement per 15.212 and KDB 996369 D01

‘Modular Certification Guide v01r04

The radio elements must have the radio frequency circuitry

shielded. Physical components and tuning capacitor(s) may be

located external to the shield, but must be on the module

assembly

The module must have buffered modulation/data inputs to ensure

that the device will comply with Part 15 requirements with any

type of input signal

The module must contain power supply regulation on the module

The module must contain a permanently attached antenna, or

contain a unique antenna connector, and be marketed and

operated only with specific antenna(s), per Sections 15.203,

15.204(b), 15.204(c), 15.212(a), 2.929(b)

The module must demonstrate compliance in a stand-alone

configuration

The module must be labelled with its permanently affixed FCC ID

label, or use an electronic display (See KDB Publication 784748

about labelling requirements)

The module must comply with all specific rules applicable to the

transmitter including all the conditions provided in the integration

instructions by the grantee

The module must comply with RF exposure requirements

Yes.

Yes.

Yes.

Yes.

Yes.

Yes.

Name: Antonio Di Paola

Title: CEO

Date: 2021-06-30

Signature of applicant

FCC – Modular Approval Request Rev 2.0



 

 

Radiocontrolli SRL

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

USA

Date: 2021-06-30

Subject; Request for Confidentiality

FCC ID: 2ANH5RC-CC1312R-915

To Whom It May Concern,

Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we

are requesting the Commission to withhold the following attachment(s) as confidential

documents from public disclosure indefinitely.

These documents contain detailed system and equipment descriptions and are considered as

proprietary information in operation of the equipment. The public disclosure of these documents

might be harmful to our company and would give competitors an unfair advantage in the market.

In additional to above mentioned documents, in order to comply with the marketing regulations

in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that

business sensitive information remains confidential until the actual marketing of newly

authorized devices, we request Short Term Confidentiality of the following attachment(s);

Schematic Diagram

Block Diagram

Operational Description

External Photos

Test Setup Photos

Internal Photos

User Manual

OR

For 45 days, pursuant to Public Notice DA 04-1705.

For 180 days pursuant to KDB 726920 D01.

It is our understanding that all measurement test reports, FCC ID label format and

correspondence during the certification review process cannot be granted as confidential

documents and this information will be available for public review once the grant of equipment

authorization is issued.

Sincerely,

Signature:

Name: Antonio Di Paola

Title: CEO