AP0263510, AP0263511, AP0263530, AP0263540, AP0279700, AP0279710, AP0279720, SUAG00 5 GHz SU/Alpha Assembly Boards REFERENCE GUIDE Regulatory Compliance FCC/ISED - Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and ISED RSS standards. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. It is the responsibility of the installer to ensure that when using the outdoor antenna kits, only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden by FCC rules 47 CFR part 15.204 and ISED RSS standards. Warning Avertissement Caution Il est de la responsabilit de l'installateur de s'assurer que lorsque vous utilisez les kits d'antennes extrieures, seules les antennes certifis avec le produit sont utiliss. L'utilisation d'une antenne autre que ceux qui sont certifis avec le produit est expressment interdite par la rglementation FCC partie 47 CFR 15.204 et ISDE normes RSS. Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the product warranty and may expose the end user or the service provider to legal and financial liabilities. Resellers or distributors of this equipment are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas. The installer should configure the output power level of antennas according to country regulations and antenna type. Reference Guide i Prudence Warning Avertissement Les units extrieures et les antennes doivent tre installs que par des professionnels expriments d'installation qui sont familiers avec les normes locales et les codes de scurit et, si applicable, sont agres par les autorits gouvernementales de rglementation comptents. Ne pas le faire peut annuler la garantie du produit et peuvent exposer l'utilisateur final ou le fournisseur de services financiers. Revendeurs ou distributeurs de ces quipements ne sont pas responsables des blessures, des dommages ou violation des rglements lis l'installation des units extrieures ou des antennes. L'installateur doit configurer le niveau de puissance de sortie des antennes conformment aux rglementations nationales et le type d'antenne. d'obligations juridiques et The antennas used for this transmitter must be installed to provide a separation distance of at least 80 cm from all persons Les antennes utilises pour cet metteur doivent tre installes de manire fournir une distance de sparation d'au moins 85 cm par rapport toutes les personnes The module is granted to operate under FCC certification in the 4.9 / 5.2 /
5.3 / 5.4 / 5.8 GHz bands. Warning Le module est autoris fonctionner sous certification ISDE dans les bandes 4,9 / 5,3 / 5,4 / 5,8 GHz. Avertissement This device complies with Part 15 of the FCC rules and with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la norme dIndustrie Canada exempts de licence RSS (s). Son fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas causer dinterfrences, et 2. Cet appareil doit accepter toute 3nterference, y compris les 3nterferences qui peuvent causer un mauvais fonctionnement de lappareil. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada Reference Guide ii Overview The 5 GHz SU/Alpha Board is a 5 GHz assembly board operating in the 4.9, 5.2, 5.3, 5.4 and 5.8 GHz frequency bands. It is a TDD OFDM radio supporting 10, 20, 40, 50 and 80 MHz channel bandwidths. It is a 2x2 MIMO transceiver. The assembly board contains the power supply block, the CPU and peripheral block, the Ethernet communication interface and the radio transceiver block on a single board. It is installed in a host enclosure manufactured by RADWIN. The 5 GHz SU/Alpha Board is certified as a limited modular approval type under the FCC ID:
Q3K-5XSUALMOD. It is also certified under IC: 5100A-5XSUALMOD excluding the 5.2 GHz band. Condition of Use The 5 GHz SU/Alpha Board is a proprietary radio module manufactured by RADWIN. The module is not for sale to the general public or for installation in hosts not manufactured by RADWIN. The hosts names are:
1. SU Integrated 2. Alpha Integrated 3. SU Connectorized 4. Alpha Connectorized FCC rules and ISED Regulation Restrictions The host firmware is factory programmed to operate under the FCC rules and ISED regulation restrictions. The firmware is locked and inaccessible by any third party. As a result of the above the user interface allows both the installer and the user to control the host only within the boundaries of the regional restrictions. The final hosts into which the assembly boards have been installed were tested to Part 15 Subpart B. Reference Guide 1 Antennas The 5 GHz SU/Alpha Board is certified with a wide range of antenna types covering both Point-to-Point and Multipoint systems up to 32 dBi gain. Antennas Following is the list of antennas supported by the 5 GHz SU/Alpha boards:
Antenna Type Manufacturer Model Number Antenna Gain
(dBi) Flat Panel Dual Pole External RADWIN RW-9105-5159*
13 Flat Panel Dual Pole External RADWIN RW-9105-4958 16 (15@ 4.9GHz) Flat Panel Dual Pole Integrated RADWIN MR0204670 22 (21@ 4.9GHz) Flat Panel Dual Pole External RADWIN RW-9613-4960 Flat Panel Dual Pole Integrated RADWIN MT0268450*
Flat Panel Dual Pole External RADWIN RW-9622-5001 Dual Pole Dish Dual Pole Dish RADWIN RW-9721-5158 RADWIN RW-9732-4958 23 25 28 28 32
*Not valid for 4.9 GHz operation Maximum Output Power 5725 5850 MHz band FCC Part 15 Subpart E, RSS 247 The maximum output power is set as follows, under FCC and ISED regulations. The power values are for PtP systems with 13 dBi antenna gain. The highest conducted output power shall be limited on all channel bandwidths as per the table below 10 MHz: 28.0 dBm 20 MHz: 28.0 dBm 40 MHz: 29.0 dBm 80 MHz: 28.0 dBm 5150 5250 MHz band FCC Part 15 Subpart E The maximum output power is set as follows, under FCC regulations. The power values are for PtP systems with 13 dBi antenna gain 10 MHz: 26.0 dBm 20 MHz: 29.0 dBm 40 MHz: 29.0 dBm 80 MHz: 18.0 dBm Reference Guide 2 5250 5350 MHz band FCC Part 15 Subpart E, RSS 247 The maximum output power is set as follows, under FCC and ISED regulations. The power values are for systems with 13 dBi antenna gain not exceeding the 30 dBm EIRP limit 20 MHz: 17.0 dBm 40 MHz: 17.0 dBm 80 MHz: 17.0 dBm 5470 5725 MHz band FCC Part 15 Subpart E, RSS 247 The maximum output power is set as follows, under FCC and ISED regulations. The power values are for systems with 13 dBi antenna gain not exceeding the 30 dBm EIRP limit 20 MHz: 17.0 dBm 40 MHz: 17.0 dBm 80 MHz: 17.0 dBm 4940 4990 MHz band FCC Part 90 Subpart Y, RSS 111 The maximum output power is set as follows, under FCC and ISED regulations. The power values are for systems with 15 dBi antenna gain not exceeding the 85 dBm EIRP limit 10 MHz: 25.0 dBm 20 MHz: 25.0 dBm 40 MHz: 24.0 dBm - Not Applicable for Canada Labelling Requirements The assembly board is labeled with the identification numbers as follows:
FCC ID: Q3K-5XSUALMOD IC: 5100A-5XSUALMOD The host into which the board is assembled is labeled as follows:
Contains FCC ID: Q3K-5XSUALMOD Contains IC: 5100A-5XSUALMOD Hosts Test Mode Configuration Integration in various hosts requires power limitations per antenna assembly gain used with the host to comply with the FCC/ISED requirements (5.15-5.25 GHz and 4.9 GHz @ 40 MHz only for FCC) Reference Guide 3 Host Antenna Gain
(dBi) Max Output Power per Band
(dBm, GHz) 5.15-5.25 5.25-5.35 5.47-5.725 5.725-5.85 4.94-4.99 SU Connectorized and Alpha Connectorized SU Connectorized and Alpha Connectorized SU Integrated and Alpha Integrated SU Connectorized and Alpha Connectorized SU Connectorized and Alpha Connectorized SU Connectorized and Alpha Connectorized SU Connectorized and Alpha Connectorized Reference Guide 13 29.0 16 (15 @ 4.9 GHz) 26.0 22 (21 @ 4.9 GHz) 23.0 23 25 28 32 22.0 20.0 15.0 10.0 17.0 14.0 7.0 8.0 5.0 N/A N/A 17.0 14.0 7.0 8.0 5.0 N/A N/A 29.0 26.0 27.0 26.0 24.0 15.0 13.0 N/A 25.0 25.0 25.0 N/A 25.0 25.0 4