AP0158770 5 GHz Wireless Module REFERENCE GUIDE Regulatory Compliance FCC/IC - Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and IC RSS standards. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. It is the responsibility of the installer to ensure that when using the outdoor antenna kits, only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden by FCC rules 47 CFR part 15.204 and IC RSS standards. Warning Avertissement Caution Il est de la responsabilit de l'installateur de s'assurer que lorsque vous utilisez les kits d'antennes extrieures, seules les antennes certifis avec le produit sont utiliss. L'utilisation d'une antenne autre que ceux qui sont certifis avec le produit est expressment interdite par la rglementation FCC partie 47 CFR 15.204 et IC normes RSS. Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the product warranty and may expose the end user or the service provider to legal and financial liabilities. Resellers or distributors of this equipment are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas. The installer should configure the output power level of antennas according to country regulations and antenna type. AP0158770 Reference Guide i Avertissement Warning Prudence Les units extrieures et les antennes doivent tre installs que par des professionnels expriments d'installation qui sont familiers avec les normes locales et les codes de scurit et, si applicable, sont agres par les autorits gouvernementales de rglementation comptents. Ne pas le faire peut annuler la garantie du produit et peuvent exposer l'utilisateur final ou le fournisseur de services financiers. Revendeurs ou distributeurs de ces quipements ne sont pas responsables des blessures, des dommages ou violation des rglements lis l'installation des units extrieures ou des antennes. L'installateur doit configurer le niveau de puissance de sortie des antennes conformment aux rglementations nationales et le type d'antenne. d'obligations juridiques et The antennas used for this transmitter must be installed to provide a separation distance of at least 314 cm from all persons and must not be co-
located or operating in conjunction with another antenna or transmitter within a device Warning Les antennes utilises pour cet metteur doivent tre installes de manire fournir une distance de sparation d'au moins 314 cm par rapport toutes les personnes et ne doivent pas tre co-localises ou fonctionner conjointement avec une autre antenne ou un autre metteur dans un appareil The module is granted to operate under FCC certification in the 4.9/5.1/5.3/5.4/5.8 GHz bands. This device complies with Part 15 of the FCC rules and with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la norme dIndustrie Canada exempts de licence RSS (s). Son fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas causer dinterfrences, et 2. Cet appareil doit accepter toute 3nterference, y compris les 3nterferences qui peuvent causer un mauvais fonctionnement de lappareil. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada AP0158770 Reference Guide ii Overview The AP0158770 is a wireless module operating in the 4.9, 5.1, 5.3, 5.4 and 5.8 GHz frequency bands. It is a TDD OFDM radio supporting 5 MHz, 10 MHz, 20 MHz, 40 MHz and 80 MHz channel bandwidths. The wireless module cannot work as a stand-alone device. It can operate and be controlled only when attached to a digital main board and altogether assembled in an enclosure suitable for outdoor use. The assembly of the wireless module attached to the digital main board is hereafter referred to as ODU. The ODU in its various outdoor enclosures is manufactured by RADWIN. The wireless module is certified as a limited modular approval type under the FCC ID: Q3K-
5XACMOLD. It is also certified under IC: 5100A-5XACMOD. Condition of Use The AP0158770 wireless module is a proprietary radio interface and can only be connected to digital boards manufactured by RADWIN. The ODU resides in an outdoor enclosure also manufactured and assembled by RADWIN or its subcontractors. The wireless module is not for sale to the general public. FCC rules and IC Regulation Restrictions The ODU firmware is factory programmed to operate under the FCC rules and Industry Canada regulation restrictions. The firmware is locked and inaccessible by any third party. As a result of the above the user interface allows both the installer and the user to control the ODU only within the boundaries of the regional restrictions. Antennas The AP0158770 wireless module is certified with a wide range of antenna types covering both Point-to-Point and Point-to-Multipoint systems up to 32 dBi gain. AP0158770 Reference Guide 1 Antennas Following is the list of antennas supported by the AP0158770 5 GHz Wireless Module:
Antenna Type Manufacturer Model Number Antenna Max Gain (dBi) Sector Dual Pole Integrated 120 Deg RADWIN Ltd. MT0128930 Sector Dual Pole 120 Deg RADWIN Ltd. RW-9061-5004 Sector Dual Pole Integrated 95 Deg RADWIN Ltd. AM0135060 Sector Dual Pole 90 Deg RADWIN Ltd. RW-9061-5001 11 11 12 14 Sector Dual Pole 60 Deg RADWIN Ltd. RW-9061-5002 16.5 Sector Dual Pole Integrated 90 Deg RADWIN Ltd. MT0125250 Flat Panel Dual Pole Integrated RADWIN Ltd. AM0119960 13 16 Flat Panel Dual Pole Integrated RADWIN Ltd. AM0111760 16.5 Flat Panel Dual Pole Integrated RADWIN Ltd. MT0070760 Flat Panel Dual Pole External RADWIN Ltd. RW-9612-5001 Flat Panel Dual Pole External RADWIN Ltd. RW-9622-5001 Dual Pole Dish Dual Pole Dish RADWIN Ltd. RW-9721-5158 RADWIN Ltd. RW-9732-4958*
Shark Fin Monopole RADWIN Ltd. RW-9401-5002 Smart Antenna Multi Pole Integrated RADWIN Ltd. AM0156430 24 23 29 29 32 12.5 20.5
* Not applicable for 4.9 GHz band Maximum Output Power 5725 5850 MHz band - FCC/IC The maximum output power can be set as follows, when operating in the 5.8 GHz band, under FCC and IC regulations. The power values are for PtP systems and PtMP systems with 0 to 6 dBi total antenna assembly gain. For PtMP systems the total EIRP is limited to 36 dBm. Therefore the output power for these systems, using higher than 6 dBi total antenna assembly gains will be reduced to comply with 36 dBm EIRP. The highest conducted output power shall be limited to 30 dBm in all channel bandwidths 5150 5250 MHz band FCC The maximum output power can be set as follows when transmitting in the 5.1 GHz band, under FCC regulations. The total EIRP limit for PtP applications is 53 dBm. The total EIRP limit for PtMP applications is 36 dBm. The total EIRP limit for PtMP applications when transmitting at elevations above 30 relative to the horizon is 21 dBm. 5 MHz: 25.0 dBm 10 MHz: 27.0 dBm 20 MHz: 27.0 dBm AP0158770 Reference Guide 40 MHz: 27.0 dBm 80 MHz: 29.0 dBm 2 40 MHz: 19.0 dBm 80 MHz: 19.0 dBm 40 MHz: 19.0 dBm 80 MHz: 19.0 dBm 5250 5350 MHz band FCC/IC The maximum output power can be set as follows, when operating in the 5.3 GHz band. The total EIRP limit is 30 dBm. 5 MHz: 14.0 dBm 10 MHz: 16.0 dBm 20 MHz: 19.0 dBm 5470 5725 MHz band FCC/IC*
The maximum output power can be set as follows, when operating in the 5.3 GHz band. The total EIRP limit is 30 dBm. 5 MHz: 14.0 dBm 10 MHz: 17.0 dBm 20 MHz: 19.0 dBm 4940 4990 MHz band - FCC/IC The maximum output power can be set as follows, when operating in the 4.9 GHz band, under FCC and IC. The power values shown below are for systems using 0 to 26 dBi total antenna assembly gain. Systems using 29 dBi antenna gain must reduce output power by 3 dB. 5 MHz: 26.97 dBm 10 MHz: 27.41 dBm 20 MHz: 28.24 dBm Radio parameters accessed by end-user The following parameters can be accessed by user:
1. Output Power 2. Frequency channel 3. Channel bandwidth 4. Antenna gain in external antenna type device
* Under IC regulations the 5600-5650 MHz band is excluded from operation AP0158770 Reference Guide 3