FCC ID: 2ADGHCON2005 Embedded WiFi Module

OEM INTEGRATION INSTRUCTIONS: (additional information) This device is intended only for OEM integrators under the following conditions: The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the external antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Validity of using the module certification:

In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. This host device must be kept away from all persons by 20cm or more and installations using less distance, or installations using antennas with gain greater than that with which this was Certified will require additional approvals.

TinyCon_AT Instruction





TinyCon_AT Instruction Ver V1.1.4 Date2015/06/10 1 Ralinwi Nanjing Electronic Technology Co., Ltd.













TinyCon_AT Instruction





AT Introduce AT is a user terminal interface for TinyCon2005, which provides users a set of the command operation interface, convenient user testing and checking information. How to enable AT Hardware connection AT work on TinyCon2005 UART interface, so you need to TinyCon2005 UART interface and through the derivation of additional circuit or device connected to a computerIf you are using a TinyWiEV - 1000 development board, then TinyWiEV -

1000 development board has UART derivation, using a mini USB cable to connect to the computer. Enter AT Enter AT Must make TinyWiEV - 1000 board dial switch to 1 (high level) or input $$$at UART interface. In this case, the TinyCon2005 is powered on or reset automatically enter AT mode. Note: WiFi module to enter configuration mode to enter $$$, frame wait time defaults value is 50 ms. When serial return OK by entering the AT (or at), into command mode. TINYCON S2W APP at OK AT OK AT Command Introduce 2 Ralinwi Nanjing Electronic Technology Co., Ltd.

















TinyCon_AT Instruction AT Command Classification TinyCon2005 AT instruction has five instruction set l serial port control instruction set l WiFi interface instruction set l Network control instruction set l Auto connect instruction set l Other instruction set Serial port control instruction set AT instruction ATB ATSn=p ATB=

Description UART parameters take effect after reset Set various adapter interface parameters Function UART parameters take effect after reset. Format Settings ATB=<baudrate>

[[,<databits>][,<parity>][,<stopbits>][,<flowcontrol>]]

Parameter baudrate Baud rate 115200support 9600~921600 databits Data bits 77bit 8 8bit parity Parity nnone e even parity o odd parity stopbits Stop bits 1 (1 stop bit) 2 (2 stop bits) flowcontrol Flow control nfc (none) fc hardware Example: setting up the serial port parameters (baud rate 115200, the data bits of 8, no check, 1 stop bit, and none flow control) ATB=115200,8,n,1,nfc OK ATSn=p FunctionSet various adapter interface parameters Format Settings ATSn=p Parameter Example: Set the frame trigger a length of 1400 n=0 to 2 p=parameter value 0=auto frame length 1=auto frame wait time 2=auto frame interval ATS0=1400 OK 3 Ralinwi Nanjing Electronic Technology Co., Ltd.















TinyCon_AT Instruction WiFi interface instruction set



Description Associate to specified SSID, optionally using specified security parameters. Disassociate from the current network. Network scan, returns list of found networks in the format. Set 802.11 country code. Set 802.11 PHY mode:

Current RSSI as ASCII Adapter reports the current wireless settings to the serial host Current wireless and network configuration. Create a network on specified channel (only open and WAP2-PSK supported). Start specify the PIN code to protect the process. the simple-config process. Optionally AT instruction at+wa at+wd at+ws at+wcountry at+wphymode at+wrssi=?

at+wsetting=?

at+nstat=?

at+wap at+sc at+wa parameters. Format Settings Parameter at+wa=rlwap Joining Network... Connected to rlwap DHCP: started IP address: 192.168.1.103 OK FunctionAssociate to specified SSID, optionally using specified security at+wa=< ssid >[,<password>,<wep keyindex>]

ssid specify the SSID to connect the AP password set the key, if the security type for wep type 5 or 13 ASCII characters; If the security type for wpa_psk, wpa2_psk input 8 ~ 32 ASCII characters. wep keyindex set the wep key SN for 0 ~ 3 Example: Join a AP ,SSID is rlwap, encryption for the open Example: Join a AP , SSID is sytest, the secret key for 123456789, encryption for wpa2 4 Ralinwi Nanjing Electronic Technology Co., Ltd.



at+wa=sytest,123456789 Joining Network... Connected to sytest DHCP: started IP address: 192.168.2.158 OK











FunctionNetwork scan, returns list of found networks in the format. Format



TinyCon_AT Instruction at+wd



FunctionDisassociate from the current network. Format at+wd Settings Example:

at+ws at+wd Disassociated OK at+ws Settings Example:

at+ws Scanning... 1 6 WPA2 AES

[1] c8:3a:35:49:04:e0 -42 2 6 Open

[2] 08:10:79:11:cc:5e -44

[3] 00:22:c3:81:98:3a -52 1 6 WPA2 AES

[4] 14:75:90:09:42:26 -52 6 6 WPA2 AES

[5] d4:ca:6d:87:28:ba -56 1 6 WPA2 AES 11 6 WPA2 AES

[6] b8:c7:5d:0c:5d:81 -62 11 6 Open

[7] e4:d3:32:ac:a7:8e -62

[8] 64:e4:25:11:00:84 -74 1 6 WPA2 AES

[9] 64:e4:25:11:00:9d -84 1 6 WPA2 AES WLAN SCAN END at+wcountry FunctionSet 802.11 country code (available for US only). Format at+wcountry=< contry string>

contry string :

US The United States Settings Parameter Example:

at+wcountry=us OK 5 Ralinwi Nanjing Electronic Technology Co., Ltd.













SC_TEST_AP rlwap New AP sun aibo AppleYao testTCP RLW_LED_64e42511084 sunwenhaoudptest n:

1 3 802.11 b/g 11 802.11 b 802.11 b/g/n



TinyCon_AT Instruction at+wphymode



FunctionSet 802.11 PHY code. Format Settings Parameter at+wphymode=n FunctionCurrent RSSI as ASCII Format Example: set up to BG mode at+wrssi=?

at+wphymode=3 OK at+wrssi=

Settings Parameter none Example:

at+wrssi=?

-45 OK at+wsetting=?

Parameter None Example:

at+wsetting=?

WMODE=STA SSID=rlwap CHANNEL=2 SECURITY=OPEN PASSWORD=

OK at+nstat=?

FunctionAdapter reports the current wireless settings to the serial host Format Settings at+wsetting=

FunctionCurrent wireless and network configuration. Format 6 Ralinwi Nanjing Electronic Technology Co., Ltd.













TinyCon_AT Instruction





Settings at+nstat=?

Parameter None Example:

at+nstat=?

MAC=00:E0:4C:87:00:00 WSTATE=CONNECTED WMODE=STA BSSID=E4:D3:32:AC:A7:8E SSID="rlwap" CHANNEL=2 SECURITY=OPEN IP addr=192.168.1.103 SubNet=255.255.255.0 Gateway=192.168.1.1 DNS1=192.168.1.1 O at+wap FunctionCreate a network on specified channel (only open and WAP2-PSK at+wap =<SSID>,<Channel>[,<WPA2Password >]

ssid To create an AP SSID specified channel Channel Settings 1~13 password 8~32 ASCII character set the AP ssid is sun, channel 1, encryption mode for the open set the AP ssid to sun, channel 1, encryption mode for wpa2 ,key is 12345678 supported). Format Settings Parameter Example:

at+wap=sun,1 Creating network...

"sun" created IP address: 192.168.1.165 DHCPS: started OK at+wap=sun,1,12345678 Creating network...

"sun" created IP address: 192.168.1.165 DHCPS: started OK at+sc FunctionStart the simple-config process. Optionally specify the PIN code to protect the process. Format Settings 7 Ralinwi Nanjing Electronic Technology Co., Ltd.













custom PIN code : Set the PIN protection configuration program TinyCon_AT Instruction





at+sc=[<custom PIN code>]

Parameter Example:

at+sc OK Joining network... Connected to rlwap DHCP: started IP address: 192.168.1.103 Auto connect instruction set AT instruction at+nauto at+wauto ato ata ata2 atd atn at+nauto Description Sets network parameters to be used for Auto Connect. Sets WiFi parameters to be used for Auto Connect. Return to Auto-Connect mode. Initiate auto connection using parameters set by AT+WAUTO and AT+NAUTO. Initiate auto connection when the adapter is already associated with an AP. Disconnect session. Returns the Auto-Connect. current network Auto-Connect status of network current FunctionSets network parameters to be used for Auto Connect. Format Settings at+nauto=<Type>,<Protocol>,<Destination IP/ Host Name>

<Destination Port>,[<Src port>]

0 client 1 server 1 TCP Parameter Type Protocol 0 UDP Destination ip Destination IP

/Host Name / Host Name Destination Port Destination Port Src port Src port e.g.:4096 Example:

e.g.:192.1.168.1.1 e.g.www.ralinwi.com e.g.:8080 at+nauto=0,1,192.168.1.101,5001,5002 OK 8 Ralinwi Nanjing Electronic Technology Co., Ltd.















TinyCon_AT Instruction at+wauto



FunctionSets WiFi parameters to be used for Auto Connect. Format Settings STA mode:

AP mode:

at+wauto=<mode><SSID>[,<Password>,<WEP Key Index>]

Parameter at+wauto=<mode><SSID>,<channel>[,<WPA2 Password>]

mode 0 STA 1 AP SSID specify the SSID to connect the AP Password The STA mode, key of the AP WEP Key Index the STA mode, if you need to connect the AP for WEP encryption type mode, enter 0 channel AP mode, automatic reconnection channel set (1 ~ 13) WPA2 Password AP mode keys: set the key security type for wpa_psk, wpa2_psk, input 8 ~ 32 ASCII characters. Example:

at+wauto=0,test OK at+wauto=0,test,12345,0 OK at+wauto=0,test,12345678 OK at+wauto=1,testAP,12 OK at+wauto=1,testAP,12,12345678 OK ato FunctionReturn to Auto-Connect mode. Format Settings ato Parameter None Example:

9 Ralinwi Nanjing Electronic Technology Co., Ltd.













TinyCon_AT Instruction





ato OK ata FunctionInitiate auto connection using parameters set by AT+WAUTO and AT+NAUTO. Format Settings ata Parameter Example:

None ata Joining Network... Connected to New AP DHCP: started IP address: 192.168.2.168 CONNECTING TO REMOTE... ESTABLISHED OK ata2 FunctionInitiate auto connection when the adapter is already associated with an AP. Format None Settings ata2 Parameter Example:

ata2 CONNECTING TO REMOTE... ESTABLISHED OK atd FunctionDisconnect current network Auto-Connect session. Format Settings atd Parameter Example:

None 10 Ralinwi Nanjing Electronic Technology Co., Ltd.













FunctionReturns the current status of network Auto-Connect. Format TinyCon_AT Instruction





atd NWCONN DIS OK atn None Example:

Settings atn Parameter atn NO NWCONN OK Network control instruction set AT instruction at+mac=?

at+ipset at+dhcp=n at+dhcpsrvr=n at+dnsset at+dnslookup at+mac=?

Description Returns the current adapter MAC address. Static network parameters overrides previous values. If 1, DHCP is enabled Prior to start the server, the adapter should be configured with a valid static IP address. Sets the DNS server addresses to be used. Queries DNS server for address of hostname URL. FunctionReturns the current adapter MAC address. Format Settings at+mac=?

Parameter None Example:

at+mac=?

00:E0:4C:87:00:00 OK at+ipset FunctionStatic network parameters overrides previous values. Format Settings at+ipset =<Local ip>,<Net Mask>,<Gateway>

11 Ralinwi Nanjing Electronic Technology Co., Ltd.













TinyCon_AT Instruction





Parameter Local ip IP address Net Mask Gateway mask e.g. 255.255.255.0 gateway: e.g. 192.168.1.1 e.g. 192.168.1.101 at+ipset=192.168.1.122,255.255.255.0,192.168.1.1 OK Example:

at+dhcp FunctionIf 1, DHCP is enabled Format Settings at+dhcp=n 1 enable dhcp client Parameter n 0 disable dhcp client Example:

at+dhcp=0 OK at+dhcpsrvr static IP address. Format Settings at+dhcpsrvr=n Parameter n 0 disabled dhcp server Example:

1 enable dhcp server at+ dhcpsrvr =0 OK at+dnsset FunctionSets the DNS server addresses to be used. Format Settings Parameter Example:

at+dnsset=<DNS1 ip>

DNS1 ip DNS at+dnsset=114.114.114.114 OK 12 Ralinwi Nanjing Electronic Technology Co., Ltd.













FunctionPrior to start the server, the adapter should be configured with a valid FunctionQueries DNS server for address of hostname URL. Format



TinyCon_AT Instruction at+dnslookup



Settings at+ dnslookup=<url>

Parameter Example:

url domain at+dnslookup=www.mtime.com 59.151.32.20 OK Other instruction set AT instruction at+dsv at+webconfgen=n ATEn at+fwup=ip,port at+reset at&f at+ver=?

at+ping at&w at&v at+dsv Description if Enable = 1,device discover enable if n = 1,web config enabled If 1, echo all inputs The adapter will enter the OTA upgrade mode. Reset the adapter. Restore profile settings to factory default values. Return the current adapter firmware versions. PING the host provided. Optionally specify the count. Save current profile to NV memory. Output current and saved profile values in ASCII. Functionif Enable = 1,device discover enable Format Settings at+dsv= <Enable>[<Device Name>, <User ID>]

Enable 0 disabled device discovery Device Name device name User ID device ID 1 enable device discovery Parameter Example:

at+dsv=1,RLWLED,9527 OK at+webcfgen=n Functionif n = 1,web config enabled Format 13 Ralinwi Nanjing Electronic Technology Co., Ltd.













TinyCon_AT Instruction





Settings at+webcfgen=n n 0 disabled web config Parameter 1 enable web config Example:

at+webcfgen=1 OK ATEn Settings ATEn Parameter Example:

ATE0 OK at+fwup FunctionIf 1, echo all inputs Format n 0 disabled echo 1 enable echo FunctionThe adapter will enter the OTA upgrade mode. Format Settings at+fwup=ip,port Parameter port Example:

ip: The target OTA server address The target server port at+fwup=192.168.2.198,8082 OK at+reset FunctionReset the adapter. Format Settings at+reset Parameter None Example:

at+reset OK 14 Ralinwi Nanjing Electronic Technology Co., Ltd.















TinyCon_AT Instruction at&f



FunctionRestore profile settings to factory default values. Format Settings at&f Parameter None Example:

at&f OK at+ver=?

FunctionReturn the current adapter firmware versions. Format Settings at+ver=

Parameter None Example:

at+ver=?

APP VERSION=2.1.0b1 WLAN VERSION=2.6a APP TYPE=S2W BUILD TIME=15:51:44 BUILD DATE=Mar 31 2015 OK at+ping FunctionPING the host provided. Optionally specify the count. Format at+ping=<ip/hostname><n>

ip/hostname Enter domain name or IP address n The number of ping Settings Parameter Example:

at+ping=8.8.8.8 PING 8.8.8.8(8.8.8.8): 120(148) data bytes 72 bytes from 8.8.8.8: icmp_seq=1 time=349 ms 72 bytes from 8.8.8.8: icmp_seq=2 time=332 ms 72 bytes from 8.8.8.8: icmp_seq=3 time=330 ms 72 bytes from 8.8.8.8: icmp_seq=4 time=331 ms

--- 8.8.8.8 ping statistics ---

4 packets transmitted, 4 received, 0% packet loss, time 1342 ms 15 Ralinwi Nanjing Electronic Technology Co., Ltd.













TinyCon_AT Instruction





at+ping=8.8.8.8,10 PING 8.8.8.8(8.8.8.8): 120(148) data bytes 72 bytes from 8.8.8.8: icmp_seq=1 time=263 ms 72 bytes from 8.8.8.8: icmp_seq=2 time=331 ms 72 bytes from 8.8.8.8: icmp_seq=3 time=330 ms 72 bytes from 8.8.8.8: icmp_seq=4 time=331 ms 72 bytes from 8.8.8.8: icmp_seq=5 time=434 ms 72 bytes from 8.8.8.8: icmp_seq=6 time=322 ms 72 bytes from 8.8.8.8: icmp_seq=7 time=236 ms 72 bytes from 8.8.8.8: icmp_seq=8 time=330 ms 72 bytes from 8.8.8.8: icmp_seq=9 time=331 ms 72 bytes from 8.8.8.8: icmp_seq=10 time=330 ms

--- 8.8.8.8 ping statistics ---

10 packets transmitted, 10 received, 0% packet loss, time 3238 ms OK at&w FunctionSave current profile to NV memory. Format Settings at&w Parameter None Example:

at&w OK at&v FunctionOutput current and saved profile values in ASCII. Format Settings at&v Parameter None Example:

16 Ralinwi Nanjing Electronic Technology Co., Ltd.













TinyCon_AT Instruction





at&v E1 B=115200,8,N,1,NFC

+DHCP=1 +IPSET=192.168.1.122,255.255.255.0,192.168.1.1

+DNS1=114.114.114.114

+DHCPSRVR=1

+WAUTO=0,rlwap

+NAUTO=0,1,192.168.1.101,8086,8087

+DISCOVER=1,rlw,www.ralinwi.com

+WEBCFGEN=1 S0=1400 S1=500 S2=0 OK 17 Ralinwi Nanjing Electronic Technology Co., Ltd.













FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 15.105 Information to the user.

(b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncont rolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. The final end product must be labelled in a visible area with the following:

Contains Transmitter Module 2ADGHCON2005