FCC ID: MEE-DX-929 CB Transceiver

DX 929 RF GAIN DIMMER dB S 1 0 2 MOD PWR 5 5 0 4 3 0 SWR 1 7 9

+20 6 0 80 100%

1 0 20 3040 50 2 1. 5 3 M A X

+40

6 0 SWR NB/ANL HI TALKBACK CB OFF RX/TX PWR PA LO SWR VOL SQ MIC GAIN POWER DX 929 OFF Two Way Citizen Band Mobile Transceiver With StarLite Face Plate OWNERS MANUAL TABLE OF CONTENTS CHAPTER 1 Specifications . CHAPTER 2 Installation . Installing The Radio . Ignition Noise Interference . Antenna . External Speaker . Public Address . CHAPTER 3 Operation . Front Panel . Rear Panel . Frequency Chart . Procedure to Receive and Transmit . Alternate Microphone and Installation . Maintenance And Adjustment . A Few Rules That Should Be Obeyed . How Your CB Can Serve You . Use Channel 9 For Emergency Message Only . PAGE 2 3 3 4 4 4 4 5 5 8 9 10 11 14 15 15 16

- 1 -

CHAPTER 1 SPECIFICATIONS CHAPTER 2 INSTALLATION GENERAL Model Channels Frequency Range Frequency Control Frequency Stability Temperature Range Antenna Impedance Antenna Connectors Input Voltage Size Weight TRANSMITTER RF Power Output Spurious Emission Unwanted Sideband Audio Distortion Frequency Response Microphone RECEIVER Sensitivity for 10 dB (S+N)/N Squelch Sensitivity Selectivity Image Rejection Hum & Noise AGC Figure of Merit Audio Power Output Audio Response DX 929 40 26.965 ~ 27.405 MHz Phase-Lock-Loop (PLL) Synthesizer 0.001%

-30C to +50C 50 Ohms Standard SO-239 type 13.8V DC 7 3/8 (W) x 8 3/4 (D) x 2 1/4 (H) 4.2 lbs. AM 3.8 watts

> -60 dB

-50 dB 10%

300 to 2500 Hz Dynamic

< 0.5 uV

< 0.5 uV

> -50 dB

> 60 dB

> -40 dB 50 mV for 10 dB Change in Audio Output 2.5W @ 10% Distortion 300 to 2500 Hz INSTALLING THE RADIO Choose a convenient location for operation that does not interfere with driver or passenger. This radio is supplied with a universal mounting bracket. When mounting the bracket and radio to your car, make sure it is mechanically strong. Also, provide a good electrical grounding connection to the chassis of vehicle. Proceed as follows to install the radio. 1. Locate a convenient area in your vehicle for the installation of the radio. Hold the mounting bracket with the radio in the location where the radio is to be installed. Make sure nothing will interfere with either the radio or the mounting bolts. Mark and then drill holes for the mounting bracket. 2. Most radio antennas come equipped with a PL-259 plug. Connect this plug to the ANT. Jack in the rear of the radio. 3. Extending from the rear of the radio is a fused red and black wire for the DC connections to the vehicles electrical system. For best performance, it is strongly recommended that the red lead be taken directly to the positive terminal on the vehicles battery and the black lead be connected to the nearest chassis ground.

(Note: This radio is designed for vehicles with negative ground systems.) Connections should be made using appropriate crimp on lugs of a size large enough to make good contact with the bolt used to fasten to the battery and the chassis ground. It is a good safety idea to install a second fuse that would provide protection in case the red wire was to fray or get pinched and short to the body of the vehicle, somewhere between the battery and the radio. High power radios such as this one require large DC current flow when in the TX mode. Poor power connections cause supply voltage drops that can substantially decrease the performance of your radio. A good DC connection is probably one of the most important things for getting the best transmitter performance and in some cases, least receiver noise. 4. Mount the microphone bracket near the radio in an easily accessible spot using the two screws provided.

(SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE)

- 2 -

- 3 -

IGNITION NOISE INTERFERENCE With weak signals, you may experience interference of the signal by background noise. This radio has NB and ANL circuits which will help reduce background noise from sources such as your ignition system. However, background electrical noise may come from several sources and all noise may not be eliminated. With extremely weak signals, you can operate this radio with the engine turned off, which should improve reception. If the ignition noise level is too high to allow proper operation under most conditions, you should have your installation of the radio checked by a qualified technician. ANTENNA This radio has a jack in the rear for a standard PL-259 antenna plug. If you are looking for the most range for your transmission, use a vertically polarized, quarter-

wave length antenna. If antenna height is a problem, you may use a shorter, loaded-

type whip antenna although you can expect some loss of transmission range. To improve performance, your antenna should be matched to your radio. Your antenna can be adjusted so that it matches your radio. EXTERNAL SPEAKER The external speaker jack (EXT SP.) on the rear panel is used for remote receiver monitoring. The external speaker should have 8 ohms impedance and be able to handle at least 3.8 watts. When the external speaker is plugged in, the internal speaker is disconnected. PUBLIC ADDRESS To use the Public Address (PA) function, first connect an external speaker to the PA. SP. Jack on the rear of the radio. See the above specifications for a proper external speaker. Keep the speaker away from the microphone to avoid acoustic feedback. CHAPTER 3 OPERATION CONTROL FUNCTIONS FRONT PANEL 8 9 10 11 12 13 14 15 16 RF GAIN DIMMER dB S 1 0 2 MOD PWR 5 5 0 4 3 0 SWR 1 7 9

+20 6 0 80 100%

1 0 20 30 40 50 2 1. 5 3 M A X

+40

6 0 SWR NB/ANL HI TALKBACK CB OFF RX/TX PWR PA LO SWR VOL SQ MIC GAIN POWER DX 929 OFF 1 2 3 4 5 6 7 1. MICROPHONE JACK: Used to connect microphone for voice source. 2. SQUELCH CONTROL: This knob is used to eliminate background noise being heard through the receiver, which can be disturbing when no transmissions are being heard through the receiver. To use this feature, turn the knob fully counterclockwise and then turn clockwise slowly until the background noise is just eliminated. Further clockwise rotation will increase the threshold level which a signal must overcome in order to be heard. Only strong signals will be heard at a maximum clockwise setting. 3. ON/OFF VOLUME CONTROL: This knob controls the volume and power to the radio. To turn radio on, rotate the knob clockwise. Turning the knob further will increase the volume of the receiver. 4. MIC GAIN CONTROL: Adjusts the microphone gain in the transmit and PA modes. This controls the gain to the extent that full talk power is available several

- 4 -

- 5 -

14. TALKBACK (TB) SWITCH: This switch is used to monitor your own voice. For example, you could use this feature to compare different microphones. 15. RX/TX LED: The red LED indicates the unit is in the transmit mode. The green LED indicates the unit is in the receive mode. 16. CHANNEL DISPLAY: The channel display indicates the current selected channel. inches away from the microphone. In the Public Address (PA) mode, the control functions as the volume control. POWER CONTROL: This control allows the user to adjust RF power output. 5. 6. SWR LED: This LED lights red when your SWR is higher than about 3:1. This is not an exact indicator of 3:1 SWR, but it is an indication that you should check your SWR reading. 7. CHANNEL SELECTOR: This control is used to select the desired transmit and receive channel. 8. FRONT PANEL METER: The front panel meter allows the user to monitor signal strength, RF output power, SWR level and AM modulation level. 9. ILLUMINATED FACE PLATE: All faceplate lettering will fully illuminate to allow the user easy viewing at night. This unique, solid state, backlight is designed to maximize night vision while minimizing eye fatigue. Therefore, it is ideal for switch and control recognition day or night. 10. RF GAIN CONTROL: This control is used to reduce the gain of the RF amplifier under strong signal conditions. 11. DIMMER CONTROL: This knob controls the level of brightness for the meter lamp and channel display. 12. SWR/MOD/PWR SWITCH: This switch controls the function of the meter during the transmit mode. In the SWR position, the meter indicates the Standing Wave Ratio (SWR) of your antenna. There are no adjustments because the SWR circuit in this radio calibrates itself automatically. When the switch is in the MOD position, the green scale on the meter indicates your percentage of modulation in the AM mode only. It is most accurate when testing at maximum power output. When this switch is in PWR position, the meter indicates your power output. 13. NB-ANL/CB/PA SWITCH: When the switch is in the NB/ANL position, the Noise Blanker (NB) and Automatic Noise Limiter (ANL) circuits are activated. The Noise Blanker is very effective in eliminating repetitive impulse noise such as ignition interference. In the CB position, the PA function is disabled and the radio will transmit and receive on the speaker that is connected. In the PA position, the radio acts as public address amplifier. Your voice will come out of the speaker that is plugged into the PA. SP. jack on the rear panel. The radio does not operate when you are in the PA mode.

- 6 -

- 7 -

REAR PANEL FREQUENCY CHART Channel Channel Frequency Channel Channel Frequency MODEL NO. : DX 929 AM 40 CH CB TRANSCEIVER FCC ID : MEE DX 929 MADE IN CHINA DATE OF MFG.:

SERIAL NO. :

3 4 PA SP. EXT SP. ANT F.C.

- DC 13.8V +

MADE IN CHINA 1 2 1. ANTENNA: This jack accepts a 50-ohm coaxial cable with a PL-259 type plug. 2. DC POWER: This jack accepts the 13.8V DC power cable with built-in fuse. The power cord provided with the radio has a black and red wire. The black goes to negative and red goes to positive. 3. PA SP: This jack is for PA operation. Before operating, you must first connect a PA speaker (8 ohms, 4W) to this jack. 4. EXT. SP: This jack accepts a 4 to 8 ohm, 5-watt external speaker. When the external speaker is connected to this jack, the built-in speaker will be disabled. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26.965 MHz 26.975 MHz 26.985 MHz 27.005 MHz 27.015 MHz 27.025 MHz 27.035 MHz 27.055 MHz 27.065 MHz 27.075 MHz 27.085 MHz 27.105 MHz 27.115 MHz 27.125 MHz 27.135 MHz 27.155 MHz 27.165 MHz 27.175 MHz 27.185 MHz 27.205 MHz 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 27.215 MHz 27.225 MHz 27.255 MHz 27.235 MHz 27.245 MHz 27.265 MHz 27.275 MHz 27.285 MHz 27.295 MHz 27.305 MHz 27.315 MHz 27.325 MHz 27.335 MHz 27.345 MHz 27.355 MHz 27.365 MHz 27.375 MHz 27.385 MHz 27.395 MHz 27.405 MHz

- 8 -

- 9 -

- 6 -

PROCEDURE TO RECEIVE AND TRANSMIT A. MICROPHONE The push-to-talk switch on the microphone controls the receiver and transmitter. Press the switch and the transmitter is activated, release switch to receive. When transmitting, hold the microphone two inches from your mouth and speak clearly in a normal voice. This transceiver comes complete with a low impedance dynamic microphone. B. PROCEDURE TO RECEIVE 1. Be sure that power source, microphone and antenna are connected to the proper connectors before going to the next step. 2. Turn VOL knob clockwise to apply power to the radio. 3. Set the VOL for a comfortable listening level. 4. Set the MODE switch to the desired mode. 5. Listen to the background noise from the speaker. Turn the SQ knob slowly clockwise until the noise just disappears. The SQ is now properly adjusted. The receiver will remain quiet until a signal is actually received. Do not advance the control too far or some of the weaker signals will not be heard. 6. Set the CHANNEL selector switch to the desired channel. C. PROCEDURE TO TRANSMIT 1. Select the desired channel of operation. 2. Set the MIC GAIN control fully clockwise. 3. If the channel is clear, depress the push-to-talk switch on the microphone and speak in a normal voice. ALTERNATE MICROPHONES AND INSTALLATION For best results, the user should select a low-impedance dynamic type microphone or a transistorized microphone. Transistorized type microphones have low output impedance characteristics. The microphones must be provided with a four-lead cable. The audio conductor and its shielded lead comprise two of the leads. The third lead is for transmit control and fourth is for receiving control. The microphone should provide the functions shown in the schematic below. 4 WIRE MIC CABLE Pin Number 1 2 3 4 Mic Cable Lead Audio Shield Audio Lead Transmit Control Receive Control Fig. 1 Your transceiver microphone schematic. If the microphone to be used is provided with pre-cut leads, they must be revised as follows. 1. Cut leads so that they extend 7/16" beyond the plastic insulating jacket of the 2. All leads should be cut to the same length. Strip the ends of each wire 1/8" and tin microphone cable. the exposed wire.

- 10 -

- 11 -

Before beginning the actual wiring, read carefully the circuit and wiring information provided with the microphone you select. Use the minimum heat required in soldering the connections. Keep the exposed wire lengths to a minimum to avoid shorting when the microphone plug is reassembled. Fig. 2 Microphone plug wiring To wire the microphone cable to the plug provided, proceed as follows:

1. Remove the retaining screw. 2. Unscrew the housing from the pin receptacle body. 3. Loosen the two cable clamp retainer screws. 4. Feed the microphone cable through the housing, knurled ring and washer as shown Figure 2. 5. The wires must now be soldered to the pins as indicated in the above wiring tables. If a vise or clamping tool is available it should be used to hold the pin receptacle body during the soldering operation, so that both hands are free to perform the soldering. If a vise or clamping tool is not available, the pin receptacle body can be held in a stationary position by inserting it into the microphone jack on the front panel. The numbers of the microphone plug are shown in Fig. 3, as viewed from the back of the plug. Before soldering the wire to the pins, pre-tin the wire receptacle of each pin of the plug. 7. Fig. 3 Microphone plug pin numbers viewed from rear of pin receptacle. 6. Be sure that the housing and the knurled ring of Figure 2 are pushed back onto the microphone cable before starting to solder. If the washer is not captive to the pin receptacle body, make sure that it is placed on the threaded portion of the pin receptacle body before soldering. If the microphone jack is used to hold the pin receptacle during soldering operation, best results are obtained when the connections to pin 1 and 3 are made first and then the connections to pins 2 and 4. Use a minimum amount of soldering and be careful to prevent excessive solder accumulation on pins, which could cause a short between the pin and the microphone plug housing. 8. When all soldering connections to the pins of the microphone are completed, push the knurled ring and the housing forward and screw the housing onto the threaded portion of the pin receptacle body. Note the location of the screw clearance hole in the plug housing with respect to the threaded hole in the pin receptacle body. When the housing is completely threaded into the pin receptacle body, a final fraction of a turn either clockwise or counterclockwise may be required to align the screw hole with the threaded hole in the pin receptacle body. When these are aligned, the retaining screw is then screwed into place to secure the housing to the pin receptacle body.

- 12 -

- 13 -

9. The two cable clamp retainer screws should now be tightened to secure the housing to the microphone cord. If the cutting directions have been carefully followed, the cable clamp should secure to the insulation jacket of the microphone cable. 10. Upon completion of the microphone plug wiring, connect and secure the microphone plug in the transceiver. MAINTENANCE AND ADJUSTMENT This transceiver is specifically designed for the environment encountered in base installations. The use of all solid state circuitry and its light weight result in high reliability. Should a failure occur, however, replace parts only with identical parts. Do not substitute. NOTE in the performance described the OPERATION and If is not MAINTENANCE AND ADJUSTMENT sections obtained, review the operating instructions to insure that proper procedures were followed. FCC WARNING All transmitter adjustments other than those provided on front panel by the manufacturer must be made by or under the supervision of the holder of an FCC issued general radio telephone operators license. A FEW RULES THAT SHOULD BE OBEYED 1. You are not allowed to carry on a conversation with another station for more than five minutes at a time without taking a one-minute break, to give others a chance to use the channel. 2. You are not allowed to blast others off the air by over-powering them with illegally amplified transmitter power, or illegally high antennas. 3. You cant use the transceiver to promote illegal activities. 4. You are not allowed to use profanity. 5. You may not play music in your transceiver. 6. You may not use your transceiver to sell merchandised or professional service. HOW YOUR CB CAN SERVE YOU 1. Warn of traffic tie ups ahead. 2. Provide weather and road information. 3. Provide help fast in event of emergency or breakdown. 4. Suggest good spots to eat and sleep. 5. Make long trips more interesting, and help keep you awake. 6. Provide direct contact with your office or home. 7. Make friends for you as you travel. 8. Provide local information to find your destination. 9. Help law enforcement officers by reporting drunk and reckless drivers.

- 14 -

- 15 -

- 14 -

USE CHANNEL 9 FOR EMERGENCY MESSAGES ONLY The FCC gives the following examples of permitted and prohibited types of communications for use in an emergency. These are guidelines and are not intended to be all inclusive. Permitted YES NO YES NO YES NO YES NO YES NO Example Message A tornado sighted six miles north of town. This is observation post number 10. No tornado sighted. I am out of gas on interstate 95 I am out of gas in my driveway There is a four-car collusion at exit 10 on the Beltway, send police and ambulance. Traffic is moving smoothly on the Beltway Base to Unit 1, the weather Bureau has just issued a thunder storm warning. Bring the sailboat into port. Attention all motorists. The weather Bureau advises that the snow tomorrow will accumulate 4 to 6 inches. There is a fire in the building on the corner of 6th and Main Streets. This Everything is quiet here. is Halloween patrol unit number 3.

- 16 -

MEMO MEMO MEMO WARRANTY

Limited means that we will repair problems caused by factory defects or normal This radio is covered by a two year Limited parts and labor warranty. use at no charge.

Before returning a radio to us for warranty service, please call our Service Department for a Repair Authorization Number (RAN). This RAN must be written below your return address on the outside of the shipping box. Boxes, which arrive without an RAN, will be refused, and the shipping company will return the unopened box to you. Be sure to have a pen and paper ready along with the serial number of your radio before calling. We will give you the RAN and our shipping address over the phone. The telephone number of the Service Department is (760) 480-8800, and we suggest calling between 10:00 AM and 4:00 PM Pacific Time.

Please include a note with a detailed description of the symptoms. This is important because it will help the technician who works on your radio to locate your problem. Intermittent problems are easily overlooked, so be sure to give as much detail as possible in your note. Also, please include your daytime telephone number in case our technicians have any additional questions.

Do not send your power cord or microphone unless we ask for these items during our telephone conversation.

You are responsible for getting the radio safely to us. (We suggest using United Parcel Service.) You must pay to ship the radio to us, and we will pay to ship the radio back to you. Since we use UPS and they do not ship to Post Offices boxes, please provide us with a street address for the return of your radio.

We will repair and return your radio as soon as we can. We appreciate your choosing a Galaxy radio and we want you to be on the air as much as possible!

Be sure to visit our web site at www.GalaxyRadios.com Printed in China AT240N010D