RSA-4000 Manual 1. Description CanineBeam Left/Right/Center LampOn/Off Column Up/Down Home Cancel Ready
[Example]
Remote controller can control 9 motions.
[Lamp] Button : Turns on/off the laser beam.
[Column Up] Button : Height of system rises when pressed.
[Column Down] Button : Height of system lowers when pressed.
[Home] Button : Location of device initialize.
[Canine Left] Button : Move canine beam forward.
[Canine Center] Button : Move canine beam at center.
[Canine Right] Button : Move canine beam rear.
[Ready] Button : Scanner ready button When clicked, system moves to the starting position for scanning.
[Cancel] Button : Cancel button Touch to cancel scanning, close scanning screen and return to the Splash screen 1 2. How to insert batteries in the remote control Openthecoveronthebackside,asseenintheimagebelow. PreparetwoAAAsize1.5Vbatteries,check+/andinsert. Closethecover.
Warning Sinceremotecontrolisusablefromlongdistance(dozensofmeters), donotpressthebuttonwhendeviceisoutofsightforsafety. Alsousetheremotecontrolwhilethedeviceisinsight. Ifyouarenotusingtheremotecontrolforalongtime, pleaseremovethebatteries 2 3. FEATURES RF Transceiver
- Single-chip 2.4GHz ZigBee RF Transceiver module
- Low Power Consumption
- Operation Voltage : 3.0 Vdc
- high Sensitivity (-98dBm)
- On-chip VCO, LNA, and PA
- Programmable Output Power Max. 5dBm
- O-QPSK Modulation
- Scalable Data Rate: 250Kbps
- RSSI Measurement
- Compliant to IEEE802.15.4 8051-Compatible Microcontroller
- 8051 Compatible Microcontroller
- 96KB Embedded Flash Memory
- 8KB Data Memory
- 128-byte CPU dedicated Memory
- 1KB Boot ROM
- 24 General Purpose I/Os
- On-chip Power-on-Reset
- 4-channel 12-bit ADC
- ISP (In System Programming)
- Internal Temperature Sensor Clock Inputs & Power
- 16MHz Crystal for System Clock
- Separate On-chip Regulators for Analog and Digital Circuitry
- Power Supply Range for Internal Regulator
- Battery Monitoring Support 3 4. SPECIFICATION 1) Description Item Application Frequency Range I/O Supply Voltage Current Operating Temperature Standard Spec. Size Description Transceiver Module 2.425 ~ 2.470 GHz (ISM Band) 3 V (1.9 V ~ 3.3 V) 50 mA 0 ~ 40 IEEE802.15.4 212 x 53 x 15 mm 2) Electrical specifications Parameter Min Typ Max Unit RF Frequency Range RF Bandwidth Channel Bandwidth RF Output Power Receiver Sensitivity
(PER1%, Packet length of 22-byte) Normal mode (250 kbps) Maximum Input Level Current : RF Receive Mode Current : RF Transmit Mode Current : Sleep Mode 2425 2470 10 90 MHz MHz MHz dBm dBm dBm mA mA uA 2 5 5
-98 35 45 25 4 5. Contact Information Ray Co., Ltd. 332-7, Samsung 1-ro, Hwaseong-si, Gyeonggi-do, 445-330, Korea Tel : +82 31 605 1000 5 FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 6