Rayconn electronics CO.,Ltd. User Manual Name: Controller with remote ModelREC-RF100 Summarization Magic color controller suitable for SPI signal direct drive LED applications; With 256 * 256 * 256 level gray, length setting function and power off memory function, built-in a variety of patterns to choose, and can through the RF remote control to adjust all kinds of dynamic lighting change effect. Can be applied to light box advertising, the stage, home decoration, etc. But this controller belong to upgrade edition, can support ten different IC strip, support the strip line sequence switch function, at the same time support the maximum pixel points is 2048. Technical parameters working temperature: 20-60 supply voltage: DC5V external dimension: L94W59H25 mm packing size: L145W95H50 mm net weight: 126.3g gross weight: 166.8g rated power: 2.2W support the maximum pixel point: 2048 output: one groups SPI signal frequency 433MHz Rayconn electronics CO.,Ltd. External Dimension Interface Specification Power input interface:
Load output interface:
Adopt conventional DC power socket as power input interface, input voltage is 5V. data port, CLK connect clock port. Direction for use V+ connect strip positive, V- connect strip negative, DATA connect strip 1. There are eight buttons on controller panel, and every button function as follows:
ON/OFF button, it can open or close load output ;
Play/pause button, can play or pause led effect, convenient observation led static effect, dynamic model (8- 83) are effective;
Rayconn electronics CO.,Ltd. Adding button, at load close state, can adjust strip IC type,pixel point number,RGB line sequence;
Reducing button, at load close state, can adjust strip IC type, pixel point number,RGB line sequence;
Mode choosing button, mode add 1; at load close state, can switch IC type, pixel point number, RGB line sequence. Mode choosing button, mode minus 1; at load close state, can switch IC type, pixel point number, RGB line sequence. Speed-down button, dynamic model (8- 83) are effective, there are 100 steps in all. Speed up button, dynamic model (8- 83) are effective. 2. There are six buttons on remote controller panel, and every button function as follows:
ON/OFF: you can turn on or off load output at any time;
pause: mode button, you can choose playing or pausing mode, and observe the static effect of LED in pausing mode. S+: change speed increase button;
S-: Change speed slow down button, a total of 100 steps;
M+: Program choosing button, Upward choice, a total of 83 program;
M-: Program choosing button, down choice. 3. Operating instructions:
Connect the load wire at first, following by the power wire, press key, close the controller, at this key, screen up rank shows"Pixel Number:", down rank time, the screen shows"-POWER OFF-", press value means the controller current support pixel point, press key can adjust point number;
Press key again, screen up rank shows"IC Type:", down rank information means the current support IC type, through key can choose the corresponding type. Press key again, screen up rank shows"Led Sequence:", down rank information means strip RGB line sequence, because in the market, a lot of strips specification are different, some the sequence is RGB, some is RBG,GRB and so on, so this controller provide the RGB line sequence modify. Through key can choose the corresponding RGB line sequence. Rayconn electronics CO.,Ltd. 4.Standard color changes as follows:
Modes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Program instruction Static red Static green Static blue Static yellow Static purple Static Cyan Static white Red horse race lamp to right Red horse race lamp to left Green horse race lamp to right Green horse race lamp to left blue horse race lamp to right Blue horse race lamp to left Red horse lower curtain Green horse draw curtain Three mix color brush forward direction Three mix color horse race to brush Three base color horse race to brush lower curtain Three mix color horse race to brush draw curtain Seven color race to brush color forward direction Seven color race to brush color backward direction Seven color horse race to brush draw curtain Seven color horse race to brush lower curtain Three base color brush forward direction Three base color brush backward direction Three mix color brush forward direction Three mix color brush backward direction Seven color brush backward direction Seven color brush forward direction Three base color brush draw curtain Three base color brush lower curtain Seven color brush draw curtain Seven color brush lower curtain Three base color flash Seven color flash Three base color jumpy change Three mix color jumpy change Seven color jumpy change Modes 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Program instruction B/Y/C flow change forward direction G/B color draw curtain B/Y color lower curtain Seven color wave forward direction Seven color wave backward direction Blue color trail backward direction Red color trail forward direction Red color trail backward direction Green color trail forward direction Green color trail backward direction Blue color trail forward direction Yellow color trail forward direction Cyan color trail forward direction Purple color trail forward direction White color trail forward direction White color trail backward direction Seven color trail backward direction Seven color trail forward direction C/R/C gradual change forward direction P/R/P gradual change forward direction P/R/P gradual change backward direction Y/G/Y gradual change forward direction Y/G/Y gradual change backward direction C/G/C gradual change forward direction C/G/C gradual change backward direction P/B/P gradual change forward direction P/B/P gradual change backward direction C/B/C gradual change forward direction C/B/C gradual change backward direction W/R/W gradual change forward direction W/R/W gradual change backward direction G/R/G gradual change forward direction G/R/G gradual change backward direction Y/R/Y gradual change forward direction Y/R/Y gradual change backward direction R/Y/R gradual change R/P/R gradual change G/C/G gradual change Rayconn electronics CO.,Ltd. 39 40 41 42 G/B/Y flow change forward direction B/Y/C flow change backward direction Three mix color flow change forward direction Three mix color flow change backward direction 5. Controller support strip IC type as follow:
81 82 83 G/Y/G gradual change B/P/B gradual change Auto play 1-82 No. 1 2 3 4 5 6 7 8 9 10 11 Model LPD6803 TM1803 UCS1903 WS2811 TM1812 TM1809 WS2801 TLS3001 TLS3008 P9813 LPD8806 Signal line DATACLK DATA DATA DATA DATA DATA DATACLK DATA DATA DATACLK DATACLK If the strip have 2 signal line, then need to connect the ground line, clock line, data line with controller V-
CLKDATA; if the strip have 1 signal line, then need to connect the ground line, data line with controller V-
DATA is OK. Note: If the Strip V+ port voltage is the same with controller input voltage, then you can direct connect it with controller V+ port, if it is different, then need to connect to other power supply. Rayconn electronics CO.,Ltd. Typical Application Connect double signal line situation:
Connect single signal line situation:
Rayconn electronics CO.,Ltd. FCC Certification Requirements Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.