FCC ID: 2BEDG-RMAW122C-06 1200 Lumen Solar Area wall Light Set

SOLAR AREA LIGHT WITH MOTION SENSOR ITEM: RMAW122C-06 | RMAW122D-06 | RMAW122D-06 PARTS C - Light Fixture (2) D - Mounting Plate (2) PRE-INSTALLATION HARDWARE INCLUDED (note: some parts may be pre-assembled) A-Wall Anchors (4) B-Screws (4) TOOLS REQUIRED Pencil Phillips-head Screwdriver Electric drill drill bit size:

7.5mm (3/10 in.) INSTALLATION MARKING THE LOCATION Mark the location where you want to mount the light xture (Part C). Measure the width of two holes on the back of the mounting plate (Part D) and mark holes for the 2 screws (Part A) on the surface. The distance between the two holes is 2.36in. (60mm). Drill two holes. 2.36in. (60mm) x x MOUNTING THE LIGHT FIXTURE Insert the wall anchors (Part B) so they are ush with the surface. Secure the mounting plate (Part D) in place with the screws (Part A). Mount the light on the mounting plate (Part D) by aligning the holes on the back of the light to the knobs on the front of the mounting plate. Align, insert, and slide down to lock in place. B A D C NOTE: Light xture will stay on 30 seconds when triggered by motion and revert back to standby mode of 20 lumens until motion is detected. For best performance, mount the light a minimun 6 feet (1.8 m) above the ground. Detection range is 26 feet (8 m), detection angle is 120. Light xture uses radio frequency technology to link, and should not be greater than 98 feet (30 m) between the neighboring/adjacent lights. When one light is triggered by motion both lights will activate. The package includes 2 lights. These 2 lights are factory linked, and can not be linked with more of the same type light or any other lights. BATTERY INSTRUCTIONS USE RECHARGEABLE BATTERIES ONLY. Only purchase the recommended type, size, and capacity of battery. Remove batteries from equipment when product will not be in use for an extended period of time. Dispose of the battery in accordance with local, state and federal regulations. (Do not burn or discard the battery in a municipal water system or other body of water.) TROUBLESHOOTING Lights will not come on. Check the battery to ensure that it is making secure contact with the terminals. If this doesnt work, replace with a new battery. Screws Battery Cover Power Switch Battery SOLAR AREA LIGHT WITH MOTION SENSOR ITEM: RMAW122C-06 | RMAW122D-06 | RMAW122H-06 FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 -12 HOURS WITH THE SWITCH IN THE ON POSITION TO FULLY CHARGE THE BATTERY. The intelligent solar LED motion activated light measures the available battery power capacity and adjusts the light's performance to maximize runtime. REPLACING THE BATTERIES Slide the power switch to the "OFF" position. Use a Phillips head screwdriver to remove the 4 screws holding the battery cover in place. Replace old battery with a new 3.7V, 2000 mAh lithium (18650) rechargeable battery. Replace the battery cover by aligning it properly and replacing the 4 screws removed earlier. Slide the power switch to the ON position. For optimal performance, allow light xture to charge in full sunlight for 8-12 hours, to fully charge the battery.

WARNING: Do not dispose of lithium batteries in municipal waste stream or by re as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable

(nickel cadmium, nickel metal hydride or lithium ion) batteries . FCC WARNING WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. DO NOT RETURN THIS PRODUCT TO THE STORE If you have questions or need assistance, please call customer service at 1-888-445-8974 or Email solarlights@westingehouse.com. and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Rayman Lights Inc. All Rights Reserved.

Page 1 of 1 FCC ID:2BEDG-RMAW122C-06 LABEL AND LOCATION 1200 Lumen Solar Area wall Light Set Model:RMAW122C-06 FCC ID:2BEDG-RMAW122C-06

(Size: L3.5cm x 1.5cm) Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Rayman Lights Inc. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 1/24/24 Rayman Lights Inc. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID:

2BEDG-

RMAW122C-06):

Name and company of U.S. agent:

Rayman Lights Inc. Physical U.S. address of agent:

702 Interchange Blvd.Newark, DE 19711 United States FRN of U.S. agent:

0034697631 Email address of U.S. agent:

holly.wang@raymanlighting.com Rayman Lights Inc. acknowledges their obligation to accept service of process on behalf of Rayman Lights Inc.. Rayman Lights Inc. with the FRN 0034697631 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, 5 0 V Signature Holly Wang Retail Merchandising Director Rayman Lights Inc. Signature Holly Wang Retail Merchandising Director Rayman Lights Inc.

, U

) 7

) d

1 1 9 2 _ t n e g A _ S U

l e d o m

_ 8 4

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products:

FCC ID 2BEDG-RMAW122C-06 Model name RMAW122C-06, RMAW122D-06, RMAW122H-06 For the products listed above, we request permanent confidentiality for all applicable exhibits as there are:

the Operational Description the Block Diagram the Schematics The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2024-01-25 Name / Title: Holly Wang / Retail Merchandising Director Company: Rayman Lights Inc. Address: 702 Interchange Blvd. Newark, DELAWARE 19711, United States Phone: +1-135-109-9740-5 Fax: N/A Email: holly.wang@raymanlighting.com

Covered Equipment Identification Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(ii) of the Commissions Rules (47 C.F.R.) we attest as follows:

We, applicant Company Name: Rayman Lights Inc. Address:

702 Interchange Blvd. Newark, DELAWARE 19711, United States Phone: +1-135-109-9740-5 certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2024-01-25 Name / Title: Holly Wang / Retail Merchandising Director Company: Rayman Lights Inc. Address: 702 Interchange Blvd. Newark, DELAWARE 19711, United States Phone: +1-135-109-9740-5 Fax: N/A Email: holly.wang@raymanlighting.com

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commissions Rules (47 C.F.R.) we attest as follows for the product listed below:

FCC ID 2BEDG-RMAW122C-06 Model name RMAW122C-06, RMAW122D-06, RMAW122H-06 We, applicant Company Name: Rayman Lights Inc. Address:

702 Interchange Blvd. Newark, DELAWARE 19711, United States Phone: +1-135-109-9740-5 certify that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2024-01-25 Name / Title: Holly Wang / Retail Merchandising Director Company: Rayman Lights Inc. Address: 702 Interchange Blvd. Newark, DELAWARE 19711, United States Phone: +1-135-109-9740-5 Fax: N/A Email: holly.wang@raymanlighting.com

Rayman Lights Inc. 702 Interchange Blvd. Newark, DELAWARE 19711, United States Date: January 25, 2024 FCC ID: 2BEDG-RMAW122C-06 Model Number: RMAW122C-06, RMAW122D-06, RMAW122H-06 To: Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21048 To Whom It May Concern, We, Rayman Lights Inc. hereby declare that our product (1200 Lumen Solar Area wall Light Set) Model Number: RMAW122C-06, RMAW122D-06, RMAW122H-06 board, Schematic, Hardware version, Software version, structure and internal photos are same, named and appearance differently due to marketing purposes. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely,

(Signed) Name / Title: Holly Wang / Retail Merchandising Director Company: Rayman Lights Inc. Address: 702 Interchange Blvd. Newark, DELAWARE 19711, United States Phone: +1- 135-109-9740-5 Fax Number: N/A E-Mail: holly.wang@raymanlighting.com