FeRAYTAC Mini Wireless Presenter
(PC Card Size) Users Manual Be sure to carefully read this Users Manual first for the proper use of the Mini Wireless Presenter and keep it for future reference. lode PP 2400 Raytac Corporation, Tel: +886 2 8227 5596 Fax: +886 2 8227 7867 Web : http:/www.ravtac.com E-mail : service@raytac.co:
Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written prior permission of the seller. The seller provides this document without warranty, or condition of any kind. The seller may make improvements or change in the product described in this documentation at any time. Other product and company name herein may be the trademarks of their respective owners. 2004 All rights reserved. IMPORTANT SAFETY AND HEALTH INFORMATION _ CAUTION LASER RADIATION-DO NOT STARE INTO BEAM MAX OUTPUT: imW WAVE LENGTH:650+ 20nm CLASS II LASER PRODUCT. This product complies with 21 CFR. |
ARNING! RISK OF INJURY!
Laser beam can cause permanent damage to eyes. Do not look into the laser beam or shine the laser beam into your eyes, other peoples eyes, or pet's eyes WARNING! RISK OF INJURY!
Keep this device away from Children. This is a working tool, not a toy or entertainment device. It should only be used by adults. Table of Contents Chapter 1 Introduction m What's the benefits... m Equipment checklist, m System requirement. Chapter 2 Product Features m Parts descriptions (Fig. 1,2,3)... H Take out the receiver (Fig. 4).. m Put back the receive (Fig. 5)... ole Chapter 3 Getting Started Initial setup the mini wireless presenter. Using the mini wireless presenter... Chapter 4 Additional Information Specifications. m Care and Maintenance... Appendix A Regulatory Compliance, Chapter 1 Introduction Thank you for choosing Raytacs Mini Wireless Presenter.
"Enjoy Your Wireless Life With Raytac
= What's the benefits Easily control the pace of your presentation With Raytacs Mini Wireless Presenter, you don't need to stand beside your computer or have an additional person click the slide for you, nor do you need to aim at the receiver of the remote control. Slim, act eas ar Raytacs Mini Wireless Presenter is a special design presentation tool, it's USB dongle is designed small enough to snap into the main body and fit the whole wireless presenter into the PC Card slot of your notebook PC. Multi-function Raytac's Mini Wireless Presenter is the mixed of RF wireless control of PowerPoint keyboard shortcuts and the laser point. The device enables the user to control presentation slides wirelessly up to 50 feet (15 meters) away indoors, while the laser pointer up to over 40 meters from the target. Easy to use Raytacs Mini Wireless Presenter is a USB plug-and-play device with no additional software required. The laser beam safety switch provides protection against unintentional laser beam into human eyes. Equipment Checklist Carefully unpack your Mini Wireless Presenter, and keep the packing materials for future reference. Check to make sure you have all the following items:
Mini Wireless Presenter (with USB receiver) 1 CR2032 battery 1 User's Manual 1 a
@ System Requirement It is recommended to install this wireless presenter under one of the following Operating Systems:
Operating Systems a Windows 98 SE, ME, 2000, XP a Mac0S9.1 or later, Mac OS X (10.1) or later
= The Mini Wireless Presenter interface with the computer hardware is through the USB dongle. Chapter 2 Product Features Parts Description Figure 4 Laser beam
Laser key Funetion key (Fn) Front View Figure 2 USB Receiver ! |
Battery chamber a Rear View Figure 3 Link key USB Receiver 6 Take out the receiver Figure 4
@ Put back the receive Improper insertion may cause the receiver damage, please follow the instruction below to put back your receiver. Figure 5 Chapter 3 Getting Started Initial setup the Mini Wireless Presenter Step 1: Open the battery cover on the back and insert the battery. Notes on battery 2 Do not insert battery into the presenter in the wrong direction 3 Donot charge, heat. open, or short-circuit the battery. 2 Do not leave dead or exhausted battery in the presenter. 1 Ifyou do not use the presenter for a long period of time, remove the battery to avoid possible damage from battery corrosion. a Ifthe presenter does not function correctly or if the operating range becomes reduced, try to replace the battery with new one. Step 2: Take out the receiver on the back and plug it into an available USB port.
(Please refer to page 7) You may encounter the following conditions with different Operating Systems:
2 Windows 98 SE/ME The system will prompt you to insert the operating system CD-ROM and the follow the instruction to install the software required 1 Window 2000/XP The operation system identifies the receiver, prompts "USB Human Interface Device and begins installation automatically. Please follow the instruction on the screen to complete the installation procedure. Note: In case you have several remote devices working at the same time within the same rage, you need to tune up the ID with your own receiver. The following is the procedure. a Press the link key on the receiver (connected to your computer now), and the LED light will be steady for tuning. (Refer to Page 6) Press Fn key and the Link key on the Presenter simultaneously for more than three seconds. The LED on the receiver will now start flashing to confirm that tuning is done. The Wireless Presenter is ready for use now. Whenever you change new battery, you are recommended to tune up the ID again. 8 Bm Using the Mini Wireless Presenter There are six keys on the Mini Wireless Presenter. The Fn key does not function except when used simultaneously with another key. The function of each key is described below. o o a Normal mode: Function of e:
ach key when not used with the Fn key. Keys marked in black Function Laser
[Activate the laser point first by pressing and holding the Fn & Laser keys simultaneously over 3 seconds. (Warning: Never to point the laser beam to human or pets eyes during activating or lde-activating process) Slides [The same function as F5 on to activate the slide ESC The same function as ESC to stop the slide Next [Advances to the next page Prev. Return to the previous page Function mode: Function of each key when used simultaneously with the Fn key, Note: The Fn key should be pressed before clicking the other key. Keys marked in green Function Fn + OniOff [Switch the laser beam on or off Fn + Black Turn the projector beam to black screen Fn + White [Turn the projector beam to white screen Fn +Alt/Tab Change presentation programffiles Fn + Link Link the ID with the receiver Idling over 30 minutes, the las ser key will be de-activated automatically. Chapter 4 Additional Information
= Specifications a System Model name: PP2400 Frequency range: 2400~2483MHz
(16 multi chamels and 65535 ID channels) Remote range: Approx. 50 feet (15 meters) indoors, 328 (100 meters) feet outdoors Operating voltage: Remote control: 2.4V~3.3V, Laser: 2.6V~3.3V Power: CR2032 battery * 1 Very low power consumption: Normal operation <10mA_ Laser operation < 30mA Sleep < 102A Output power: Under ImW Physical Dimensions Size: 86()) x 54(w) x 5(h) millimeters Weight: Approx. 23 grams (with the receiver and battery) Environmental Requirements Temperature:
Operating: 0C (32F 60C (140F) Non-operation: -10C (14F )~65C(149F) Humidity(non-condensing):
Operating: 10%~85% RH Non-operating: 10%~-95% RH Laser: Semiconductor laser( A = 650 nm), emission duration: continuous Laser output power: Max. 0.95mW Note: Design and specifications are subject to change without notice.
@ Care and Maintenance a a a For cleaning, you are advised to use a soft, slightly moistened cloth Avoid using solvents or abrasive substances Do not open the presenter: for maintenance, consult qualified staff only. 10 Appendix A Regulatory Compliance FCC Statement on Class B Note: This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation, This equipment generate, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orient or re-locate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation, 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF Exposure:
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Patent Pending Thank you for using Raytacs Mini Wireless Presenter again Raytac Corporation FE C 5F-3, No. 755, Chung Cheng Road., Chung Ho, Taipei Hsien 235, Taiwan, ROC Tek +886 2 8227 5596 Web : htto-/Awww.raytac.com Fax: +886 2 8227 7867 E-mail : service@raytac.com ry RAYTAC I:
www.raytac.com DOC NO. EB-Az010-202 2