| submitted | available | document details (if available) | source link |
|---|---|---|---|
| April 09 2014 | May 09 2014 |
| various | UserMan | Users Manual | 1.87 MiB | April 09 2014 / May 09 2014 |
User Guide For Windows 8.1 Tablet-laptop TZ10II1 Regulatory Compliance Information FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government, Industry Canada, and other national regulatory agencies. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Equipment Authorization has been granted to this model with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching the FCC ID:
TX2-RTL8723BS; SAR limit is 1.34w/kg. For questions related to the EMC performance of this product, contact:
Elitegroup Computer Systems Co., Ltd No.239, Sec. 2, Ti Ding Blvd., Taipei, Taiwan 11493 886-2162-1177 Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil numerique nmet pas de bruits radio lectriques dpassant les limites applicables aux appareils numriques de la classe B prescrites dans le Rglement sur le broullage radiolectrique dict par le ministre des Communications du Canada. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CE mark. Declaring compliance to all the applicable European Union (EU) directives. For CE mark related questions:
Elitegroup Computer Systems Co., Ltd No.239, Sec. 2, Ti Ding Blvd., Taipei, Taiwan 11493 886-2162-1177 French SAR/DAS Votre ordinateur tablette a un DAS. Pour plus d'informations, voir le portail radiofrquences-sante-environnement:
www.radiofrequences.gouv.fr In the European Union, this symbol indicates that this product including battery must not be disposed of with household waste. It is your responsibility to hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your local waste collection center or the point of purchase of this product. Japan VCCI Statement
(VCCI) B Taiwan battery recycling:
Translation please recycle batteries Attention: Teachers, Parents and Adult Supervisors This product is an educational tool designed for school children, ages 6 and up. There must be supervision by an adult on school children under 10 when using this Intel Classmate PC -
Convertible. It is a must to have a thorough explanation to students on safe and proper handling of the Intel Classmate PC
- Convertible, power supply, battery pack, and power cord. Be sure to keep the power cord away from younger children Please ensure that students understand the following:
As with all electrical products, precautions should be observed during handling and use to prevent electric shock. The power supply (adapter) should not be handled by the children. Emphasize to students that this device is an educational tool and not a toy. The computer, power supply, battery pack or power cord should not be dropped, crushed, stepped on or otherwise abused. Ensure students understand the safe and proper handling of power cord and power supply. Misuse could result in serious injury. The teacher, parent or adult supervisor should periodically inspect the computer; power supply and power cord for damage and replace it, if necessary. Students should report any damage or loose parts to their teacher, parent or adult supervisor, immediately. Do not leave the PC plugged in or on when enclosed in a non-vented container, such as a school backpack, as overheating may occur. It is recommended that students should take a 5 minute break every 30 minutes of use. Safety Precautions The following are lists of precautionary measures the students must understand before using this computer inside the classroom or home environment:
1. Do not place near the fire or other sources of heat. 2. Do not expose to magnetic fields. 3. Do not expose to direct sunlight. 4. Do not expose to rain or moisture. 5. Do not place heavy objects to add heavy pressure on the computer. 6. Do not drop the computer. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Contents 1. Getting to know your computer ................................................. 1 Package contents .............................................................................................................. 1 Separating your tablet-laptop ...................................................................................... 2 Docking your tablet ........................................................................................................... 2 Layout ...................................................................................................................................... 3 Tablet Views ............................................................................................................. 3 Front .......................................................................................... 3 Top and Back ........................................................................ 4 Left ............................................................................................. 5 Bottom ...................................................................................... 5 Keyboard Duck Views ......................................................................................... 6 Connectors............................................................................. 6 2. Using your computer .................................................................. 7 Powering ON/OFF ............................................................................................................ 7 Powering on your computer ............................................................................. 7 Powering off your computer ............................................................................. 7 Putting your tablet into sleep mode ............................................................. 9 Waking up your computer ................................................................................. 9 Basic touch screen operations ................................................................................. 10 3. Windows Interface .........................................................................12 Start Screen ....................................................................................................................... 12 Desktop ................................................................................................................................. 13 Adding Desktop to the Start screen ........................................................... 14 Customizing your taskbar ................................................................................ 14 The Charms menu .......................................................................................................... 15 All Apps ................................................................................................................................. 17 Switching back to Start screen ................................................................................. 18 Start button ......................................................................................................................... 19 Start menu Power user menu ................................................................... 19 4. Setup and Connection .................................................................20 Setup Your Microsoft Account ................................................................................... 20 Setup your Start screen ............................................................................................... 20 Adding an App ....................................................................................................... 21 Removing an App ................................................................................................ 21 How to Boot to the Desktop directly ...................................................................... 22 Wireless LAN ..................................................................................................................... 23 Enabling wireless connection ........................................................................ 23 Connecting to a wireless LAN ....................................................................... 23 Micro SD Card Slot ......................................................................................................... 24 To insert your micro SD card ......................................................................... 24 To remove your memory card ....................................................................... 24 Connecting an External Device ............................................................................... 24 Connecting to the USB port ........................................................................... 24 Connecting a USB drive ................................................................................... 25 Disconnecting a USB drive or storage device ...................................... 25 Connecting to the HDMI port ......................................................................... 26 5. Battery ................................................................................................28 Charging your battery.................................................................................................... 28 Inspecting your battery status ................................................................................... 28 By opening the Charms .................................................................................... 28 By inspecting the taskbar ................................................................................ 29 Approximate status of your battery ........................................................................ 29 6. Windows Help and Troubleshooting .....................................31 Windows Help ................................................................................................................... 31 Troubleshooting ................................................................................................................ 31 7. Specification ....................................................................................36 1. Getting to know your computer This chapter provides an overview of the tablet, including the locations of the connectors and controls, tablet features, and accessories. Package contents Carefully unpack your box and take out the items listed as below. If any of the items is missing or damaged, contact your dealer immediately:
One tablet One keyboard docking Others One warranty card This manual One AC adapter 1 Separating your tablet-laptop Note: Make sure you have safely disconnected your USB device from the USB port on the dock. Please refer to the devices manual on how to do so. 1. Set your tablet laptop on a stable surface. 2. Eject the HDD optionally installed in your keyboard dock (the D-drive, in default). For details, see page 25. 3. Hold the screen and push down the latch. 4. Detach the screen by pulling it upward 1. Hold your tablet with the button side facing the dock. 2. Gently press and insert the tablet into the docking connector on the dock. 3. When you hear a click sound, it means the tablet is successfully docked. Docking your tablet 2 Layout Tablet Views Front No. Name Function 1 2 Front facing Often for taking self-portraits as well as for video camera conferencing. Touchscreen It is a see-touch device: You look at it and also touch it with your fingers to control the tablet. 3 Top and Back No. Name Function 1 Power lock tablet. Push here to power on/off or lock on/off your 2. 3 4 Volume up/
Press here to increase or decrease the sound down volume. Microphone Mainly for sound and speech recording. Speaker The sound system has two speakers for playing music, notification sounds, and other audio data. 4 Left No. Name Function 1 2 3 4 5 Windows button Switches the screen between the Start screen and the previously opened app/program. Micro SD card This is where you can insert a Micro SD memory slot card. USB port Here you can plug in a USB device. This is where you can connect your HDMI external screen. Here you can plug in a standard headphone. HDMI port Headphone connector 6 Power port your tablet. This is where you plug in the adapter to charge Bottom No. Name Function 1 Docking Connector A connector to the keyboard dock 5 Keyboard Duck Views Connectors No. Name Function 1 2 3. Docking Connector Touchpad A connector where you docking your tablet. Here is the touchpad that you can use it as you are using a traditional mouse. USB 2.0 port Here you can plug in a USB device. 6 2. Using your computer Powering ON/OFF Powering on your computer 1. If this is the first time you turn this computer on, connect the AC adapter and fully charge the battery. 2. Press the power button. 3. A logo will appear when the system is powered on. Powering off your computer Save all your data before powering your computer off. To power off your system, you can do one of the following:
A. By Charms 1. Slightly swipe from the right edge of the screen. This opens the Charms menu. (For more about the Charms menu, see page 15) 2. Click Settings from the menu, and you will see a menu as shown on the right, 3. Click Power icon, and select Shut down. 7 B. Using the power button Press and hold the power button for at least four seconds, and you will see an instruction appear in the middle of the screen, which is as shown below. Slide your finger on the screen downward, and the system will power off itself. If you want to cancel it, just slide your finger upward C. Using the Start button In the Start screen and Desktop, you can move your cursor to the low left corner. The Start button will shows itself. Right click the button, and the start menu will pop out 8 From the lower part the menu, select <Shut down or sign out> and then <Shut down>
Putting your tablet into sleep mode When you will be away from your computer for a short time, put the computer to sleep. Do one of the following:
When the keyboard is attached, close the display panel or press Fn +
F2. Press the power button. Open the Charms and then select <Settings> <Power> <Sleep>. Right click the start button and then select <Shut down or sign out>
<Sleep>
Waking up your computer Note: It is recommended that you put your computer to sleep before you move it. Moving your computer while the hard disk is spinning can sometimes damage the hard disk, causing loss of data. Do one of the following:
Press the power button. Press the Windows button. 9 Basic touch screen operations The monitor is not only a touch screen, but actually also is a tablet. You can use your fingers or a touch pen to perform many actions on it. Dont use sharp objects to touch the screen. Or, the screen may be damaged or scratched. Dont touch the touch screen with a conductive material. It may cause a malfunction. The supporting functions are application dependent. Gesture name Explanation Tap Touch once on an item to start an app, open a link, or perform an optional function. This is similar to a left-click with a mouse. Double-tap Slightly press twice with your finger to select an item. Press and hold Press and leave your finger on an item. This brings up detailed information or opens a menu with more options for the item. This is similar to a right-click with a mouse. 10 Pinch Rotate or Move two fingers together or apart while touching the screen. This is to zoom in and out on visual apps, such as pictures and maps. Place two or more fingers on an item and then turn your hand. This enables you to turn an object. (Note:
Not all items can be rotated, depending upon the app.) Slide Drag your finger across the screen. This can scroll through lists and pages, and can also move an object or be used to draw or write, depending upon your apps. Two-finger-slide Moves up/down, left/right. This is the same function as scrolling your mouse. Start from any edge of the screen, and then swipe toward the center of the screen. 11 Swipe 3. Windows Interface Start Screen When you turn on the computer, the Start screen is displayed, which allows you to access many features and installed applications (also referred to as apps) at one glance. Apps These bricks are the shortcuts for respective applications. User Account The currently used user account. Charms See page 15 for detailed information. 12 1 2 3 123 Desktop In Windows 8.1, the Desktop is treated as an app. You can find and activate it from your Start screen and All Apps screen. 1 2 3 4 If you want to start your computer to skip the Start screen and to directly open the Desktop, see p.22. Taskbar Allows you to add toolbars that hold extra buttons and menus. Notification Shows you the current system status and area notifications Program area This is where you can place a shortcut icon for your desired application. Charms See page 15 for detailed information. 13 3214 Adding Desktop to the Start screen If the Desktop tile cannot be found in your start screen, you can add it to the start screen by following steps:
1. Open the All Apps screen, as described in the section All Apps of this Chapter. 2. Long touch or right click the desktop app icon. 3. A command bar appears at the bottom of the screen. Click the Pin to Start option to add your Desktop tile to the Start screen. Customizing your taskbar Right-click (or press and hold using your finger) on a blank part of the taskbar, a pop-up menu leaps out. In the menu, select Toolbars and offer and you can see following five toolbar options:
Address By choosing this, part of your taskbar becomes a place for typing website addresses where you want to visit. Links This adds quick access to your favorite websites listed in your Internet Explorer's Favorites menu. 14 Touch This is for tablet owners and can add a button that Keyboard brings a keyboard to the forefront for touch-typing on the screen. Desktop This adds quick access to all your PC's resources, allowing you to browse through files, folders, libraries, network locations, and Control Panel menus without opening any menus. New Toolbar This lets you create a toolbar from any folder's contents. The Charms menu This menu consists of five options that are called charms and provide quick access to various aspects of Windows 8.1. To display the Charms, do one of the following:
Move the pointer to the upper-right or lower-right corner Use one finger to swipe in from the right edge of the screen Press Windows key + C. 15 The five charms are:
Search Search for a program or file. Simply enter a keyword in the Search charm and start search. It also enables you to perform a search within an app or on the Web. This charm is for you to transfer and share a picture or file with another user. If you are not in the Start screen, this allows you to return to the Start screen. If you are in the Start screen, this allows you to return to the previously screen, which could be an app or the Desktop. This enables you to operate directly a desired device. You can import pictures from a digital camera, stream a video to your TV, or transfer files to a device listed on the screen. Share Start Device Settings This charm enables you to perform basic tasks such as adjusting the volume, turning off the PC, etc. 16 All Apps In the Start screen, touch any blank area and slightly drag upward. Or Once you move the cursor, a downward arrow appears in the low left area of the screen, as shown below. Click the arrow. Then The All Apps screen will appear similar to what is as shown below. 17 Switching back to Start screen For switching back to the Start screen, do one of the following:
Press the Windows key on your keyboard or the Windows button on your tablet. Once you move the cursor, an upward arrow will appear. Click the upward arrow. Move the mouse cursor to the lower-left corner, and click the Windows icon. Click the Windows icon in the Charms bar. 18 Start button In the Start screen, move your cursor to the low left corner (or swipe in from the left edge of the screen if you dont use the dock keyboard), a windows icon will show up. It is the start button. A right click on the icon will open a quick access menu as shown below. In the Desktop, the Windows icon in the low left corner is the start button, and a right click on it can open the quick access menu. Start menu Power user menu Followings are some of these items that are especially useful to have at your mouse-tip:
System: opens a window that provides every possible detail about your machine. Control Panel: This is the quickest known method to get to the desktop Control Panel. Search: Having the option to choose Search here saves you a trip into TileWorld and its Charms menu. Shut down or sign out: Now shutting down, signing out, or restarting is a single step and it doesnt require leaving the Desktop. In its submenu, you can find commands for Sign out, Sleep, Shut down, and Restart. 19 4. Setup and Connection Setup Your Microsoft Account To share files or settings with other devices running Windows 8, you need to setup a Microsoft Account. Furthermore, if you want to download or purchase apps from the Microsoft Store, such Microsoft Account is required. To setup a Microsoft account 1. Open the Charms and click Settings > Change PC Settings. 2. Click Account > Your account >Connect to a Microsoft account. 3. Follow the instruction to register your account information. Setup your Start screen 20 Adding an App To add an app:
1. Open the All Apps screen. 2. Drag the top or bottom of the screen inward, and an option menu appears at the bottom of the screen. 3. Touch the icon named Customize in the menu. 4. Touch the app that you want to add to your Start screen. The available options will appear in the right side of the option menu. 5. Click Pin to Start to add the app to your Start screen. Removing an App To remove an app:
1. In the Start screen or All Apps screen, drag the top or bottom of the screen inward. An option menu is activated at the bottom of your screen. 2. Touch the icon named Customize in the menu. 3. Touch the app that you want to remove from the Start screen. The available options will appear in the right side of the option menu 4. Click Unpin from Start to remove it from the Start screen. 21 How to Boot to the Desktop directly If you want to start your computer to skip the Start screen and to directly open the Desktop, here is how:
1. From the Apps screen, open the Control Panel. If you're using the dock keyboard and are already on the Desktop, right-click on the taskbar and choose Properties, then skip to Step 4. 2. With the Control Panel open, touch or click Appearance and Personalization. 3. On the Appearance and Personalization screen, touch or click Taskbar and Navigation. 4. Touch or click the Navigation tab along the top of the Taskbar and Navigation window that is open. 5. Check the box next to < When I sign in or close all apps on a screen, go to the desktop instead of Start>. 6. Touch or click the OK button to confirm the change. From now on, after powering on your tablet or closing your open apps, the Desktop will open instead of the Start screen 22 Wireless LAN Enabling wireless connection To do this, do one of the following:
Press Fn+F1 to activate the wireless networking function. Open the Charms and select Settings to open the Network configuration page, and then toggle the Airplane mode switch to Off. To confirm that Airplane mode is disabled, go to the desktop and check the notification area. If you see an airplane icon displayed on the lower right, then Airplane mode is on. Otherwise, wireless function is enabled. Connecting to a wireless LAN Once the wireless has been enabled, the computer automatically scans for available wireless networks and displays them in the wireless LAN network list. To connect to your desired wireless network, click the networks name in the list, and then click Connect. Note: Some networks require a network security key or password for connection. If necessary, ask the network administrator or the Internet service provider (ISP) for the required information. 23 Micro SD Card Slot You can utilize your micro SD cards as removable disks and conveniently exchange data with digital devices such as a digital camera, digital camcorder, MP3, etc. To insert your micro SD card 1. Insert the micro SD card into the card slot as shown below. 2. Follow the message appeared on the screen, and choose to open and view files. 3. A Windows Explorer runs and shows all the folders and files in the micro SD cards, and you can save, move and delete data as you are handling a storage device. To remove your memory card 1. Press the card and release. The card will pop up. 2. Pull the card out by holding the end of the card. Connecting an External Device Connecting to the USB port Your computer comes with two USB ports compatible with USB devices. The one on the tablet is a micro USB 2.0 port, and the other one is on the keyboard dock. 24 Once you plug a USB device into one of these USB ports, Windows automatically loads a driver for that device. After the driver has been loaded one time, you can disconnect and reconnect the same device without performing any additional steps. Note: If Windows requires you to install the driver before connecting, check the documentation provided by the devices manufacturer before connecting the device. Connecting a USB drive The Windows system will automatically detect a USB storage device, and will provide you the options on how to explore the files. Note: If your USB device uses a power cord, connect the device to a power source before connecting it. Disconnecting a USB drive or storage device Before disconnecting a USB drive or storage device, make sure the data transfer between your computer and that device has finished. Follow following steps to disconnect the device:
1. In Desktop, click the in the notification area. If you dont see such icon, click the small triangle icon instead to display all hidden icons, as shown on the right. 25 2. A list of removable devices (similar to the one on the right) will show up. Click the device that you want to remove. 3. The system will shows you a notification telling you it's safe to remove the device. 4. If the device is the D-drive, you can safely separate the tablet from the keyboard dock now. If the device is connected to the USB port on the dock, you can disconnect its USB connection now. Connecting to the HDMI port You can connect an external display device such as a monitor, TV, projector, etc., only if such device has a HDMI port. By doing so, you have a wider view when you give a presentation or watch a video or movie. 1. Power off the external device. 2. Locate the micro-HDMI port on your computer. 26 3. Connect the small end of the HDMI cable to the port, and the other end to the HDMI port on the external device. 4. Power on the external device. When connecting a TV, you may need to configure your TV to external device mode. 5. Select Charms menu > Devices >
Second Screen. An option menu appears as shown on the right. 6. Select a desired monitor mode. 27 5. Battery Charging your battery You can charge your tablet directly by connecting the adapter to the DC jack on your tablet and to a wall socket. While system is off, it takes at least 3hrs to fully charge the battery. Inspecting your battery status There are mainly two ways to view your battery status. By opening the Charms In the Start screen or Desktop, open the Charms menu. A popup window shows up at the down-left corner of your screen, as shown below. In the lower-left corner is the battery status icon. 28 By inspecting the taskbar In Desktop, move the cursor to the battery icon in the taskbar. A pop-up dialog box appears and shows you the remaining battery percentage, as shown below. Approximate status of your battery The battery icon reveals the approximate status of your battery, which described as below. Battery is fully charged Battery is starting to drain Battery is about to completely drain, and you should stop using your tablet and charge it at once. Battery is being charged. A battery is an expendable supply, so when using it over a long time, the 29 capacity/battery life is shortened. If the battery life is reduced to under half of its initial time, we recommend purchasing a new battery. When not using the battery for a long time, store the battery after charging it to 30-40% of its capacity. This extends the battery life time. 30 6. Windows Help and Troubleshooting To know how to use Windows 8 properly, it is better to learn how to use Windows by utilizing Windows Help. Windows Help Move the pointer on the screen to the top or bottom right edge of the screen to view the Charm menu. Alternatively, drag the right edge inward with your finger to view the Charm menu. Select Charm menu > Settings > Help. For accessing to the most recent online Help, you need to connect your computer to the Internet. Troubleshooting This section describes some common problems and suggested solutions, and ways to recover your computer from a crash. Be aware that the problems and solutions described here are meant only as a guide. They are not definitive problem solving techniques. For certain problems, you might need help from your reseller or your service provider. When you observe a problem, stop operation immediately, because taking further action might result in data loss or damage. Take a note of what the system is doing and what actions you performed before 31 the problem occurred. Provide detailed information to your service provider for quicker problem resolution. For about any problem, follow these steps:
1. Restart your tablet. 2. Check your Wi-Fi connection. 3. Reset your Wi-Fi connection. 4. Plug your tablet to a wall socket to charge it for at least one hour. Display problems When I turn on the If the screen is blank, make sure that:
computer, nothing appears
- The AC adapter is connected to the on the screen. computer and the power cord is plugged into a working electrical outlet.
- The computer power is on. (Press the power button again for confirmation.) If these items are properly set, and the screen remains blank, have the computer serviced. My screen goes blank while Your power management is enabled. Do the computer is on. one of the following to resume from sleep mode:
- Press any key on the keyboard. (Cannot be used in Tablet mode.)
- Press the power button.
- Press the Windows button. 32 Sleep problems The critical low-battery error The battery power is getting low. message appears, and the Connect the AC adapter to the computer. computer turns off The computer enters sleep Make sure that the battery is charged. mode immediately after
- The operating temperature may be too Power-on. hot. Move to a cooler environment and try to wake the computer. The computer does not Connect the AC adapter, then press the return from sleep mode and Windows button or the power button. the computer does not If your computer is powered-off, connect work. the AC adapter first, and then press the power button to resume operation. Display problem The screen is blank. Do the following:
- If you are using the AC adapter, or using the battery, and the battery status indicator is on, press Fn+F8 to make the screen brighter.
- If the power indicator is blinking, press the power button to resume from sleep mode.
- If the problem persists, follow the solution in the next problem The screen is unreadable or distorted. The screen is unreadable or Make sure that:
distorted.
- The screen resolution and color quality are correctly set.
- The monitor type is correct. 33 Incorrect characters appear Are the operating system or programs on the screen. installed correctly? If they are installed and configured correctly, have the computer serviced. Keyboard problems After docking the tablet, the Do the followings:
keyboard has no response. 1. Connect the adapter to the dock. 2. Separate your tablet from the dock.
(See page 2 for details) 3. Dock your tablet again. You shall hear a click sound when you push the tablet into the dock. If the keyboard still has no response, please contact your local dealer. Sound problems No sound can be heard Make sure that:
from the speaker even
- The Mute function is off. when the volume is turned
- The combo audio jack is not being used. up.
- Speakers are selected as the playback Recovery system problems device. Fail to restore system The system partition, such as the partition to factory default. partition size or the drive capacity of C, Other problems has been modified. 34 Your computer does not To turn off your computer, press and hold respond. the power button for 10 seconds or more. If the computer still does not respond, remove the AC adapter. Your computer might lock when it enters sleep mode during a communication operation. Disable the sleep timer when you are working on the network. The connected external Do not connect or disconnect any device does not work. external device cables other than USB while the computer power is on. Otherwise, you might damage your computer. When using a high power consumption external device such as an external USB optical disk drive, use an external device power adapter. Otherwise, the device may not be recognized, or the system may shut down as a result. 35 7. Specification Processor Intel Bay TrailT-CR (1M Cache) Memory 1GB/2GB DDR3L one- channel, 1333MT/s (max.) Storage Tablet 16GB/32GB NAND flash eMMC Version 4.51 interface Keyboard dock (Optional) One SATA II/III 2.5" 7mm HDD 320GB/500GB Dimension Tablet Weight 263 x 177 x10.8 mm Keyboard dock 263 x 187 x13.6 ((26.1 with stand))mm 1300g
(Docking w/o HDD, w/o Battery); 1400g (Docking w/HDD, w/o Battery) Wireless IEEE 802.11 b/g/n Wireless LAN Touchscreen Bluetooth 4.0 10.1, 1280 x 800 TFT Color LCD (TN) 10-point touch Cameras Front facing camera: 1.2M (HD) Rear facing camera (optional): 5M 36 Battery Tablet 1S3P 6300mAh Model No.: TCL/GLW/SMP Input/Output Tablet 1 x DC-in jack 1 x micro USB 2.0 port 1 x Mic/head phone jack combo 1 x micro HDMI port 1 x micro SD card slot Keyboard Dock 1 x USB 2.0 port Gyroscope Gaming and virtual reality input devices GPS navigation systems I2C/SPI digital output interface Magnetometer/
Accelerometer sensor Compensated compass Map rotation I2C serial interface Speaker &
Speaker :
Mic Language Build-in 2 Speakers 0.7W x 4 ohm Mic:
Internal MIC Arabic Brazil Portuguese English French German Greek Hebrew Hungarian Italian 37 Latin Spanish Portuguese Russian Simplified Chinese Spanish Thai Traditional Chinese Turkish DC Output: 5V/15W 3A Input Voltage: 100240VAC Nominal Input Frequency: 5060Hz. Model No. AC-Adapter Certification EMC CE /FCC/CCC RF FCC&SAR /
R&TTE&SAR UL / CB Safety&
CCC Environment WEEE Others RoHS HDMI (D type) Energy Star 6.0 38
This product uses the FCC Data API but is not endorsed or certified by the FCC