RTL8812BU Users Manual
(Realtek RTL8812BU) USB Module Users Manual Preliminary Version 19/07/2017 Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com RTL8812BU Users Manual CONTENT ENVIRONMENTAL .......................................................................................................................... 3 OPERATING ............................................................................................................................................ 3 STORAGE ................................................................................................................................................ 3 MTBF CACULATION .............................................................................................................................. 3 WARNING .......................................................................................................................................... 3 Federal Communication Commission Interference Statement ...................... 3 INDUSTRY CANADA STATEMENT ........................................................................................................... 5 NCC ...................................................................................................... 6 RTL8812BU Users Manual ENVIRONMENTAL Operating Operating Temperature: 0C to +70 C Relative Humidity:
5-90% (non-condensing) Storage Temperature:
Relevant Humidity:
-40C to +80C (non-operating) 5-95% (non-condensing) MTBF caculation Over 150,000hours Warning Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
RTL8812BU Users Manual
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Referring to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2P. 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. RTL8812BU Users Manual USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX2-RTL8812BU ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Manual Information To the End User This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. RTL8812BU Users Manual NCC NCC :
ID Installing the Wireless USB module module Hardware Installing USB module to USB connector RTL8812BU Users Manual Un-installing the Wireless USB module Hardware Remove the Wireless USB module board from USB connector port. Installing the Wireless USB module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first. A. Execute the setup.exe, Click Next to process the installation RTL8812BU Users Manual B. Click Install to process the installation C. Click Install this driver software anyway RTL8812BU Users Manual D. After step C please press Next button. E. Press Finish button to complete the install process RTL8812BU Users Manual Un-installing the Wireless USB module Software A. Uninstall the RTL8812BU WLAN Driver from Start All Programs Please click Uninstall to remove RTL8812BU WLAN driver. REALTEK RTL8812BU can only be used with the following specific host:
NFA822B00 DataSheet OS DELL Vostro 270S (PC) ASUS-( P7H55-M/USB3 ) ASUS-(M5A87) (PC) ASUS(NB)-(U36J) ASUS-(P8Z77-V LX) GIGABYTE-(GA-880GMA-UD2H) GIGABYTE-(GA-F2A85X-UP4) MB/NB/add-in card model name Acer-Aspire VN7 719G-55MB(NB) WIN8.1 WIN7 WIN7 WIN7 WIN7 WIN7 WIN7 WIN7 GIGABYTE-(GA-H61M-USB3(B3)) WIN7 WIN8 WIN7 WIN7 WIN7 WIN7 WIN7 WIN7 WIN7 WIN7 MSI-(H67MA-E35(B3)) TOSHIBA(NB)-(R830) TOSHIBA(NB)-(R930) HP 14-R017TU(NB) Lenovo T430(NB) UTB222 UTB242 UTB245 VLI-805 add-in card USB Host Intel USB3.0 NEC USB3.0 Asmedia USB3.0 Fresco USB3.0 Intel USB3.0 Intel USB3.0 NEC USB3.0 AMD USB3.0 ETRON USB3.0 Intel USB3.0 Intel USB3.0 NEC USB3.0 Renesas USB3.0 Intel USB3.0 Renesas USB3.0 TI USB3.0 Fresco USB3.0 VLI USB3.0 Page 12/12