all | frequencies |
|
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 |
|
Manual | Users Manual | 477.66 KiB | January 07 2001 | |||
1 2 3 |
|
Operational Manual | Users Manual | 973.25 KiB | / December 01 2004 | |||
1 2 3 |
|
Users manual | Users Manual | 1.89 MiB | November 09 2003 | |||
1 2 3 |
|
WISI manual | Users Manual | 524.52 KiB | December 12 2003 / December 01 2004 | |||
1 2 3 |
|
WPR manual | Users Manual | 269.95 KiB | December 12 2003 / December 01 2004 | |||
1 2 3 | Cover Letter(s) | December 12 2003 / December 01 2004 | ||||||
1 2 3 | External Photos | December 12 2003 / December 01 2004 | ||||||
1 2 3 | ID Label/Location Info | December 12 2003 / December 01 2004 | ||||||
1 2 3 | Internal Photos | December 12 2003 / December 01 2004 | ||||||
1 2 3 | Cover Letter(s) | December 12 2003 / December 01 2004 | ||||||
1 2 3 | Test Report | December 12 2003 / December 01 2004 | ||||||
1 2 3 | Cover Letter(s) | December 12 2003 / December 01 2004 | ||||||
1 2 3 | Test Setup Photos | December 12 2003 / December 01 2004 | ||||||
1 2 3 | Cover Letter(s) | December 01 2004 | ||||||
1 2 3 | Cover Letter(s) | September 01 2004 / December 01 2004 | ||||||
1 2 3 | Cover Letter(s) | November 09 2003 | ||||||
1 2 3 | Cover Letter(s) | November 09 2003 | ||||||
1 2 3 | Test Report | November 09 2003 | ||||||
1 2 3 | External Photos | November 09 2003 | ||||||
1 2 3 | ID Label/Location Info | November 09 2003 | ||||||
1 2 3 | Internal Photos | November 09 2003 | ||||||
1 2 3 | Test Setup Photos | November 09 2003 | ||||||
1 2 3 | Block Diagram | January 07 2001 | ||||||
1 2 3 | External Photos | January 07 2001 | ||||||
1 2 3 | Internal Photos | January 07 2001 | ||||||
1 2 3 | ID Label/Location Info | January 07 2001 | ||||||
1 2 3 | Operational Description | January 07 2001 | ||||||
1 2 3 | Test Report | January 07 2001 | ||||||
1 2 3 | Test Setup Photos | January 07 2001 |
1 2 3 | Manual | Users Manual | 477.66 KiB | January 07 2001 |
i W y r e l e s s A c c e s s T M P r e
P r o d u c t i o n S y s t e m 6
2 0
0 1 S e t u p a n d O p e r a t i n g P r o c e d u r e s 1
. I n t r o d u c t i o n T h i s m a n u a l h a s b e e n d e s i g n e d t o h e l p y o u u n d e r s t a n d t h e o p e r a t i o n o f y o u r W y r e l e s s A c c e s s T M P r e
P r o d u c t i o n S y s t e m
. P l e a s e f a m i l i a r i z e y o u r s e l f w i t h t h e s y s t e m a n d i t s p a r t s b e f o r e o p e r a t i n g
. T h e s y s t e m i n c l u d e s o n e D o o r C o n t r o l M o d u l e I n t e r f a c e
D C M I
, o n e m o u n t e d I n t e g r a t e d R e a d e r L o c k
I R L
) a n d o n e A c c e s s o r y K i t
. T h e i n f o r m a t i o n p r o v i d e d i s p r e l i m i n a r y a n d w i l l c h a n g e
. T h i s s y s t e m i s a p r e
p r o d u c t i o n s y s t e m
. I t i s n o t i n t e n d e d t o b e a f u l l
f e a t u r e s y s t e m
. P l e a s e s e e s e c t i o n 2 1
, P r e
P r o d u c t i o n S y s t e m L i m i t a t i o n s f o r a m o r e c o m p l e t e d e s c r i p t i o n o f i t s l i m i t a t i o n s
. F o r q u e s t i o n s n o t a n s w e r e d b y t h i s m a n u a l r e g a r d i n g t h e s e t u p a n d o p e r a t i o n o f t h e W y r e l e s s A c c e s s P r e
P r o d u c t i o n S y s t e m
, p l e a s e c o n t a c t _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
. F C C C o m p l i a n c e T h i s d e v i c e i s d e s i g n e d t o c o m p l y w i t h P a r t 1 5 o f t h e F C C R u l e s a n d w i t h R S S
2 1 0 o f I n d u s t r y C a n a d a
. O p e r a t i o n i s s u b j e c t t o t h e f o l l o w i n g t w o c o n d i t i o n s
1
) T h i s d e v i c e m a y c a u s e h a r m f u l i n t e r f e r e n c e
, a n d
2
) t h i s d e v i c e m u s t a c c e p t a n y i n t e r f e r e n c e r e c e i v e d
, i n c l u d i n g i n t e r f e r e n c e t h a t m a y c a u s e u n d e s i r e d o p e r a t i o n
. T h i s e q u i p m e n t w i l l b e t e s t e d t o c o m p l y w i t h t h e l i m i t s f o r a C l a s s B d i g i t a l d e v i c e a n d a C l a s s B i n t e n t i o n a l r a d i a t o r
, p u r s u a n t t o P a r t 1 5 o f t h e F C C R u l e s
. W a r n i n g C h a n g e s o r m o d i f i c a t i o n s n o t e x p r e s s l y a p p r o v e d b y t h e p a r t y r e s p o n s i b l e f o r c o m p l i a n c e c o u l d v o i d t h e u s e r s a u t h o r i t y t o o p e r a t e t h e e q u i p m e n t
. T h i s d e v i c e h a s n o t b e e n a u t h o r i z e d b y t h e F C C R u l e s
. T h i s d e v i c e i s n o t
, a n d m a y n o t b e
, o f f e r e d f o r s a l e o r l e a s e o r s o l d o r l e a s e d u n t i l a u t h o r i z a t i o n i s o b t a i n e d
. 3
. W a r n i n g s R F e x p o s u r e T o c o m p l y w i t h F C C R F e x p o s u r e r e q u i r e m e n t s f o r p o r t a b l e t r a n s m i t t i n g d e v i c e s t h i s t r a n s m i t t e r s h o u l d o n l y b e u s e d o r i n s t a l l e d a t l o c a t i o n s w h e r e t h e r e i s a t l e a s t a 2 0 c m s e p a r a t i o n b e t w e e n t h e a n t e n n a a n d a l l p e r s o n s
. U s e o n l y t h e B a t t e r y P a c k s p e c i f i e d i n t h i s i n s t r u c t i o n m a n u a l
. D o n o t s u b j e c t B a t t e r y P a c k t o f i r e o r h i g h t e m p e r a t u r e s
. D o n o t a t t e m p t t o r e c h a r g e
, s h o r t o r d i s a s s e m b l e B a t t e r y P a c k
. F o l l o w l o c a l r e g u l a t i o n s f o r b a t t e r y d i s p o s a l
. I m m e d i a t e l y r e m o v e t h e b a t t e r i e s a n d d i s c o n t i n u e u s e i f
T h e p r o d u c t i s i m p a c t e d a f t e r w h i c h t h e i n t e r i o r i s e x p o s e d
, T h e p r o d u c t e m i t s a s t r a n g e s m e l l
, h e a t o r s m o k e
. D o n o t d i s a s s e m b l e
. I f u n i t s t o p s w o r k i n g o r d i s a s s e m b l y i s n e e d e d
, c o n t a c t R e c o g n i t i o n S o u r c e a t 6 3 0
7 6 2
4 4 5 0 f o r i n s t r u c t i o n s
i i T a b l e o f C o n t e n t s 1
. I N T R O D U C T I O N I 2
. F C C C O M P L I A N C E I 3
. W A R N I N G S I T A B L E O F C O N T E N T S I I 4
. G E N E R A L D E S C R I P T I O N 1 4
. 1 C O M P O N E N T S O F T H E W Y R E L E S S A C C E S S S Y S T E M 1 4
. 1
. 1 D o o r C o n t r o l M o d u l e I n t e r f a c e
D C M I
) 1 4
. 1
. 2 I n t e g r a t e d R e a d e r L o c k
I R L
) 1 4
. 1
. 3 A c c e s s o r y K i t 1 4
. 2 O P E R A T I N G O P T I O N S 1 4
. 2
. 1 S t a n d
A l o n e O p e r a t i o n 1 4
. 2
. 2 P a n e l
C o n n e c t e d O p e r a t i o n 2 4
. 3 C A R D S W I P E 2 5
. D C M I P A R T N A M E S 2 2 i i i 6
. D C M I P C B F U N C T I O N A L C O M P O N E N T S 3 6
. 1 8
P I N H E A D E R S 3 6
. 2 T A C T I L E S W I T C H E S 3 6
. 3 2
P I N H E A D E R 3 6
. 4 3
P I N H E A D E R 3 6
. 5 4
S W I T C H D I P S W I T C H 4 6
. 6 L E D S 4 7
. I R L P A R T N A M E S 4 8
. I R L F U N C T I O N A L C O M P O N E N T S 5 8
. 1 T O R X B O S S 5 8
. 2 B A T T E R Y W I R E H A R N E S S 5 8
. 3 P R O G R A M M I N G W I R E H A R N E S S 5 9
. A C C E S S O R Y K I T P A R T N A M E S 6 1 0
. A C C E S S O R Y K I T 6 1 0
. 1 B A T T E R Y P A C K 6 1 0
. 2 B A T T E R Y O V E R R I D E C A B L E 6 1 1
. D C M I S E T U P F O R S T A N D
A L O N E M O D E 7 1 1
. 1 S T A N D
A L O N E M O D E
, D C M I S I M U L A T E S A P A N E L 7 S O T H A T T H E S Y S T E M C A N B E T E S T E D A N D E V A L U A T E D W I T H O U T A P A N E L
, T H E P R E S E N C E O F A P A N E L M U S T B E S I M U L A T E D
. W I R I N G A J U M P E R B E T W E E N T H E S T R I K E A N D G R O U N D
T O P T W O
) P I N S O F E A C H 8 P O S I T I O N T E R M I N A L B L O C K
O N H E A D E R S J 3
J 4
) O N T H E D C M I P C B W I L L S I M U L A T E A P A N E L
. S E E F I G U R E 5
. 7 1 1
. 2 P O W E R T O T H E D C M I I N S T A N D
A L O N E M O D E 7 1 2
. D C M I S E T U P F O R P A N E L
C O N N E C T E D M O D E 8 1 3
. 1 C O M M U N I C A T I O N S O V E R V I E W 9 1 3
. 2 H O W T O S E T T O A N R F C H A N N E L 9 1 4
. L I N K M O D E 1 0 1 4
. 1 L I N K I N G 1 0 1 4
. 2 L I N K P R O C E S S 1 0 1 4
. 3 H O W T O P U T T H E D C M I I N T O L I N K M O D E 1 0 1 5
. I R L L I N K I N G T O T H E D C M I V I A B A T T E R Y C O N N E C T I O N 1 1 1 5
. 1 O V E R V I E W 1 1 1 5
. 2 C O N N E C T T H E I R L B A T T E R Y P A C K T O I N I T I A T E L I N K I N G T O T H E D C M I 1 1 1 6
. W H E N A N D H O W T O C H A N G E T H E R F C H A N N E L 1 2 i v 1 7
. U N D E R S T A N D I N G T H E D C M I S L E D I N D I C A T O R S 1 2 1 8
. U N D E R S T A N D I N G T H E I R L S L E D I N D I C A T O R S A N D I N T E R N A L S O U N D E R 1 3 1 9
. O P E R A T I N G T H E W Y R E L E S S A C C E S S S Y S T E M 1 4 1 9
. 1 O V E R V I E W 1 4 1 9
. 2 C A R D S W I P I N G 1 4 1 9
. 3 I N D I C A T I O N S O F A S U C C E S S F U L C A R D S W I P E 1 5 1 9
. 4 I N D I C A T I O N O F A N U N S U C C E S S F U L C A R D S W I P E 1 5 1 9
. 5 I N D I C A T I O N S O F A S U C C E S S F U L R E Q U E S T
T O
U N L O C K
C A R D S W I P E
) 1 5 1 9
. 6 I N D I C A T I O N S O F A N U N S U C C E S S F U L R E Q U E S T
T O
U N L O C K
C A R D S W I P E
) 1 6 2 0
. O T H E R S O F T W A R E F E A T U R E S 1 6 S E N S E S A N D R E P O R T S D O O R P O S I T I O N T O T H E P A N E L
. 1 6 P E R I O D I C A L L Y R E P O R T S T O P A N E L F O R H O U S E K E E P I N G U P D A T E S
, 1
, 2
, 5 O R 1 5 M I N U T E S I N T E R V A L S
, C O N F I G U R A B L E
. B A T T E R Y L I F E I S A F U N C T I O N O F T H I S T I M E P E R I O D A N D N U M B E R O F C A R D S W I P E S
. R E Q U E S T
T O
E X I T
. 1 6 2 1
. P R E
P R O D U C T I O N S Y S T E M L I M I T A T I O N S 1 7 F C C D O E S N O T H A V E F C C A P P R O V A L
. 1 7 U L D O E S N O T H A V E U L A P P R O V A L
. 1 7 S H O C K A N D V I B R A T I O N S H O C K A N D V I B R A T I O N T E S T S H A V E N O T B E E N C O M P L E T E D
. 1 7 L I N K M O D E A T T E N U A T E D B Y 3 D B F E A T U R E H A S N O T B E E N I M P L E M E N T E D
. 1 7 L O W B A T T E R Y I N D I C A T I O N A T T H E P A N E L F E A T U R E H A S N O T B E E N I M P L E M E N T E D
. 1 7 I N T E R N A L C A C H E M E M O R Y F E A T U R E I S N O T I M P L E M E N T E D
. 1 7 I R L R E A D E R T A M P E R S W I T C H F E A T U R E H A S N O T B E E N I M P L E M E N T E D
. 1 7 D C M I T A M P E R S W I T C H F E A T U R E H A S N O T B E E N I M P L E M E N T E D
. 1 7 R S 4 8 5 C O M M U N I C A T I O N P R O T O C O L T O T H E P A N E L S C H E D U L E D F O R R E L E A S E 2
. 1 7 2 2
. C A R E A N D U S A G E 1 7 A L W A Y S O P E R A T E T H E W Y R E L E S S A C C E S S P R E
P R O D U C T I O N S Y S T E M W I T H I N I N S T R U C T I O N S A N D S P E C I F I C A T I O N S D E S C R I B E D I N T H I S M A N U A L
. 1 7 K E E P T H E D C M I D O O R A N D I R L B A T T E R Y C O M P A R T M E N T C L O S E D W H E N I N U S E
. 1 7 D O N O T U S E T H E S Y S T E M O U T D O O R S
. 1 7 D O N O T P A I N T A N Y P A R T
, E S P E C I A L L Y T H E D C M I A N T E N N A O R I R L A N T E N N A C O V E R
. 1 7 2 3
. S P E C I F I C A T I O N S
1 7 2 3
. 1 B O T H C O M P O N E N T S 1 7 2 3
. 2 I R L 1 7 2 3
. 3 D C M I 1 7 2 4
. T R O U B L E S H O O T I N G 1 8 2 5
. O T H E R I N S T A L L A T I O N R E Q U I R E M E N T S 1 9 v C O D E O F F E D E R A L R E G U L A T I O N S 1 9 Wyreless Access TM Door Control Module Interface (DCMI) Integrated Reader Lock (IRL). MHz RF Spread Spectrum Technology. DCMI DCMI RF IRL Magstripe Wiegand transceiver Accessory Kit 1 4
. G e n e r a l D e s c r i p t i o n i s a w i r e l e s s a c c e s s c o n t r o l p e r i p h e r a l s y s t e m
. S i m p l y
, i t a l l o w s a p a n e l t o c o n t r o l a r e m o t e d o o r w i t h o u t a n y w i r i n g f r o m t h e p a n e l t o t h e d o o r o r a n y w i r i n g a t o r a r o u n d t h e d o o r
. T h e s y s t e m c o n s i s t s o f t w o c o m p o n e n t s
a a n d a n I t c o m m u n i c a t e s u s i n g 9 0 0 A n A c c e s s o r y K i t i s a l s o p r o v i d e d
. 4
. 1 C o m p o n e n t s o f t h e W y r e l e s s A c c e s s S y s t e m 4
. 1
. 1 D o o r C o n t r o l M o d u l e I n t e r f a c e
D C M I
) T h e i n c l u d e s
1
) a n r e c e i v e r a n d t r a n s m i t t e r
) t o c o m m u n i c a t e w i t h a n a n d
2
) a n i n t e r f a c e t o a n a c c e s s c o n t r o l p a n e l
. T h e w i l l i n t e r f a c e w i t h a n y a c c e s s p a n e l u s i n g e i t h e r
c l o c k
d a t a
) o r
d a t a 1
d a t a 0
) c o m p a t i b l e i n p u t s
. O n e D C M I i s c a p a b l e o f c o n t r o l l i n g t w o I R L s
. A D o o r C o n t r o l M o d u l e I n t e r f a c e E x p a n d e d
D C M I E
, c a p a b l e o f c o n t r o l l i n g f o u r I R L s
, i s a l s o a v a i l a b l e
. 4
. 1
. 2 I n t e g r a t e d R e a d e r L o c k
I R L
) T h e I R L i n c l u d e s 7 c o m p o n e n t s
a n e l e c t r i c a l l o c k p l u s r e a d e r
, p o w e r s u p p l y
, o p t i o n a l d o o r p o s i t i o n c o n t a c t s a n d R e q u e s t
t o
E x i t s e n s o r
. I t a l s o i n c l u d e s a n R F r e c e i v e r a n d t r a n s m i t t e r
t r a n s c e i v e r
. T h e I R L m o u n t s o n a s t a n d a r d c y l i n d r i c a l
c u t d o o r
I R L s f o r m o r t i s e
c u t d o o r s w i l l b e a v a i l a b l e s o o n
. 4
. 1
. 3 A c c e s s o r y K i t T h e c o n t a i n s a p o r t a b l e d o o r j a m b w i t h t h e I R L m o u n t e d o n i t
. T h i s w i l l n o t b e p r o v i d e d i n t h e p r o d u c t i o n v e r s i o n
. T h e K i t a l s o i n c l u d e s t w o b a t t e r y p a c k s o f f o u r A A a l k a l i n e b a t t e r i e s a n d o n e c o n n e c t o r e a c h
. A s i n g l e b a t t e r y p a c k o f e i g h t A A a l k a l i n e b a t t e r i e s a n d o n e c o n n e c t o r w i l l b e p r o v i d e d i n p r o d u c t i o n v e r s i o n s
. A B a t t e r y O v e r r i d e C a b l e
, 9 V B O C
, w i l l a l s o b e s u p p l i e d
. 4
. 2 O p e r a t i n g O p t i o n s T h e p r e
p r o d u c t i o n s y s t e m o p e r a t e s i n t w o w a y s
S t a n d
A l o n e O p e r a t i o n o r P a n e l
C o n n e c t e d O p e r a t i o n
. 4
. 2
. 1 S t a n d
A l o n e O p e r a t i o n S t a n d
A l o n e i n v o l v e s o n l y t h e I R L a n d D C M I
. I n S t a n d
A l o n e
, t h e I R L t r a n s m i t s a R e q u e s t
t o
U n l o c k a f t e r a c a r d s w i p e
. T h e D C M I r e c e i v e s t h i s r e q u e s t t h e n t r a n s m i t s b a c k a n u n l o c k c o m m a n d
. T h i s m o d e i s i n t e n d e d f o r e v a l u a t i n g b a s i c c o m m u n i c a t i o n s p e r f o r m a n c e l e v e l s
. Panel Connected Operation Magstripe Wiegand IRL Request-to-Unlock DCMI DCMI IRL RF. Pre-production units have Magstripe readers. Wiegand & Prox readers will be available. Manual Card Swipe is required for either Stand-Alone or Panel-Connected Operation. The user must swipe a card to begin a transmission. Only when a card has been swiped will the IRL transmit a Request-to-Unlock. In Stand Alone mode, a mag stripe card with Track 2 data will be needed to transmit a valid Request-to-Unlock. In Panel-Connected mode, a valid card must be used to result in a valid Request-to-Unlock, like normal.
2 4
. 2
. 2 P a n e l
C o n n e c t e d O p e r a t i o n r e q u i r e s c o n n e c t i o n t o a n a c c e s s c o n t r o l p a n e l w i t h
c l o c k
d a t a
) o r
d a t a 1
d a t a 0
) p r o t o c o l
. A f t e r a c a r d s w i p e
, t h e t r a n s m i t s a
. T h e r e c e i v e s t h i s r e q u e s t a n d c o m m u n i c a t e s i t t o t h e p a n e l v i a w i r e s
. W h e n t h e p a n e l r e s p o n d s w i t h a n u n l o c k c o m m a n d
, t h e r e c e i v e s t h e c o m m a n d v i a w i r e s a n d t r a n s m i t s i t t o t h e v i a 4
. 3 C a r d S w i p e 5
. D C M I P a r t N a m e s S T R I K E G R O U N D R E Q U E S T
T O
E X I T D O O R S T A T U S T R O U B L E D A T A C L O C K G R O U N D 4 8 5 B u s 3
P I N H E A D E R
, J 6
G R N D
, A
, B
) S T R I K E G R O U N D R E Q U E S T
T O
E X I T D O O R S T A T U S T R O U B L E D A T A C L O C K G R O U N D 8
P I N H E A D E R
, J 3 8
P I N H E A D E R
, J 4 T A C T I L E S W I T C H
, S 1 D o o r A T A C T I L E S W I T C H
, S 2 D o o r B L E D
G R N
R E D
, C R 9 L E D
R E D
, C R 1 0 L E D
R E D
, C R 7 L E D
G R N
R E D
, C R 6 L E D
G R N
, C R 1 5 P o w e r s u p p l i e d b y p a n e l 2
P I N H E A D E R
, J 1
P o w e r
) 4
P O L E
, D I P S W I T C H
, S W 7 F i g u r e 1
D C M I P r i n t e d C i r c u i t B o a r d
P C B
) F U S E 3 6
. D C M I P C B F u n c t i o n a l C o m p o n e n t s A s p r e v i o u s l y s t a t e d
, t h e D C M I i s c a p a b l e o f c o n t r o l l i n g t w o I R L s
. T h e c o m p o n e n t s o n t h e l e f t s i d e o f t h e D C M I P C B w i l l b e d e s i g n a t e d f o r I R L A w h i l e c o m p o n e n t s o n t h e r i g h t w i l l b e d e s i g n a t e d f o r I R L B
. T h e f o l l o w i n g t e x t d e s c r i b e s t h e f u n c t i o n s o f t h e P C B c o m p o n e n t s
F i g u r e 1
. N o t e A l l h e a d e r s
m a l e t e r m i n a l p i n s t r i p s
) w i l l h a v e t e r m i n a l b l o c k s a t t a c h e d
. 6
. 1 8
P i n H e a d e r s T h e r e a r e t w o 8
p i n h e a d e r s
, o n e f o r e a c h d o o r
. T h e l e f t 8
p i n h e a d e r i s m a r k e d J 3
, a n d t h e r i g h t
, J 4
J 3 a p p l i e s t o I R L A
J 4 a p p l i e s t o I R L B
) T h e 8
p i n h e a d e r p r o v i d e s e i t h e r 1
) t h e c o n n e c t i o n s t o a p a n e l f o r P a n e l O p e r a t i o n o r 2
) t h e t w o p i n s
n o t e d a s S t r i k e a n d G r o u n d
) n e e d e d t o b e c o n n e c t e d t o g e t h e r i n o r d e r f o r t h e D C M I t o f u n c t i o n i n S t a n d
A l o n e O p e r a t i o n
. F i g u r e 1 n o t e s t h e f u n c t i o n o f e a c h p i n o n t h e 8
p i n h e a d e r
. 6
. 2 T a c t i l e S w i t c h e s T w o t a c t i l e s w i t c h e s
S 1 a n d S 2
) a r e l o c a t e d o n t h e D C M I P C B
. A g a i n
, t h e t a c t i l e s w i t c h o n t h e l e f t
S 1
) a p p l i e s t o I R L A
, a n d t h e t a c t i l e s w i t c h o n t h e r i g h t
S 2
) a p p l i e s t o I R L B
. T h e t a c t i l e s w i t c h i s u s e d t o p u t t h e D C M I i n t o L i n k M o d e
. W h e n t h e D C M I i s i n L i n k M o d e
, i t i s i n r e c e i v e m o d e
, w a i t i n g f o r t h e f i r s t l i n k r e q u e s t t r a n s m i s s i o n f r o m a n I R L i n o r d e r t o l i n k t h e I R L a n d D C M I s o t h a t t h e s y s t e m c a n b e o p e r a t e d
. T h e s w i t c h c a n a l s o b e u s e d t o t a k e t h e D C M I o u t o f L i n k M o d e
. M o r e d e t a i l e d i n f o r m a t i o n o n L i n k M o d e f o l l o w s i n s e c t i o n 1 4
, L i n k M o d e
. 6
. 3 2
P i n H e a d e r O n e 2
p i n h e a d e r
J 1
) i s l o c a t e d t o t h e l e f t o f t h e 8
p i n h e a d e r
J 4
. T h e 2
p i n h e a d e r i s a l w a y s t h e c o n n e c t i o n t o t h e p a n e l p o w e r i n e i t h e r t h e S t a n d
A l o n e M o d e o r t h e P a n e l
C o n n e c t e d M o d e
. P l u s i s l e f t p i n
, n e g a t i v e i s r i g h t p i n
. 6
. 4 3
P i n H e a d e r O n e 3
p i n h e a d e r
J 6
) i s l o c a t e d t o t h e r i g h t o f t h e 8
p i n h e a d e r
J 3
. T h i s i s f o r a f u t u r e R S 4 8 5 i n t e r f a c e t o a c o n t r o l p a n e l a n d f o r l o c a l t r o u b l e s h o o t i n g a n d c o n f i g u r a t i o n
. T h e l e f t p i n i s g r o u n d
, t h e c e n t e r p i n i s A
, a n d t h e r i g h t p i n i s B
. 4 6
. 5 4
S w i t c h D i p s w i t c h T h e r e i s o n e 4
p o l e d i p s w i t c h
S W 7
. T h e d i p s w i t c h d e t e r m i n e s t h e R F c h a n n e l t o b e u s e d
. A s t h e r e i s o n l y o n e d i p s w i t c h
, d o o r s A a n d B w i l l c o m m u n i c a t e o n t h e s a m e R F c h a n n e l
. 6
. 6 L E D s T h e f o l l o w i n g d e s c r i b e s t h e s e v e n L E D s a n d t h e m e s s a g e s t h e y c o n v e y
. 6
. 6
. 1 G r e e n L E D
, C R 1 5
, w h e n b l i n k i n g
, i n d i c a t e s t h e m i c r o p r o c e s s o r i s r u n n i n g a n d p o w e r i s o n
. N o t e
I f t h e p o w e r i s o f f
, C R 1 5 m a y s t i l l b e b l i n k i n g b u t t h e m i c r o p r o c e s s o r i s n o t r u n n i n g
. 6
. 6
. 2 R e d L E D s
, C R 1 0 a n d C R 7
, i n d i c a t e T r o u b l e a t i t s r e s p e c t i v e I R L s u c h a s L o w B a t t e r y
, T a m p e r
, N o C o m m u n i c a t i o n
. 6
. 6
. 3 C R 9 a n d C R 6 a r e d u a l g r e e n a n d r e d L E D s
. E a c h i n d i c a t e s e i t h e r L i n k M o d e o r S t a n d b y M o d e f o r i t s r e s p e c t i v e I R L
. W h e n i n L i n k M o d e
, t h e g r e e n a n d r e d L E D s f l a s h a l t e r n a t e l y
. W h e n i n S t a n d b y M o d e
, t h e g r e e n L E D s i l l u m i n a t e c o n t i n u o u s l y
. 6
. 6
. 4 G r e e n a n d r e d L E D s
, C R 9 a n d C R 6
, a l s o i n d i c a t e R F c o m m u n i c a t i o n
. T h e r e d L E D w i l l f l a s h o n c e p e r s e n t t r a n s m i s s i o n
. T h e g r e e n L E D f l a s h e s o n c e p e r r e c e i v e d t r a n s m i s s i o n
. S e e S e c t i o n 1 8
, U n d e r s t a n d i n g t h e I R L s L E D I n d i c a t o r s a n d I n t e r n a l S o u n d e r
. 7
. I R L P a r t N a m e s F i g u r e 2 M a g S t r i p e R e a d e r A n t e n n a C o v e r B a t t e r y C o v e r R e a d e r L E D A u x i l i a r y B a t t e r y S o c k e t Programming Wire Harness PCB Programming Wire Harness 5 8
. I R L F u n c t i o n a l C o m p o n e n t s T h e A n t e n n a C o v e r
, B a t t e r y C o v e r
, R e a d e r
, R e a d e r L E D a n d A u x i l i a r y B a t t e r y S o c k e t a r e s h o w n i n F i g u r e 2
. F i g u r e 3 T h e f o l l o w i n g d e s c r i b e s v a r i o u s o t h e r c o m p o n e n t s t h a t m a k e u p t h e I R L
F i g u r e 3 8
. 1 T o r x B o s s A T o r x s c r e w s e c u r e s t h e B a t t e r y C o v e r
. I t f i t s i n t o t h e t o p c e n t e r o f t h e b a t t e r y c o v e r a n d s c r e w s i n t o t h e T o r x b o s s
. N o t e
T h i s r e q u i r e s a T o r x s e c u r i t y s c r e w d r i v e r
s i z e T 9
. 8
. 2 B a t t e r y W i r e H a r n e s s T h e B a t t e r y W i r e H a r n e s s i s l o c a t e d i n t h e b a t t e r y c o m p a r t m e n t
. I t i s t h e w i r e h a r n e s s t h a t h a s t w o
, 2
p o s i t i o n c o n n e c t o r s a t t h e e n d
. T h e s e c o n n e c t o r s c o n n e c t t o t h e B a t t e r y P a c k s t h a t s u p p l y p o w e r t o t h e I R L
. 8
. 3 P r o g r a m m i n g W i r e H a r n e s s T h e P r o g r a m m i n g W i r e H a r n e s s i s l o c a t e d i n t h e b a t t e r y c o m p a r t m e n t
. I t i s t h e w i r e h a r n e s s w i t h t h e R J 1 1
6 p i n
, 6 w i r e
) c o n n e c t o r
. T h e c o n n e c t s t h e I R L t h r o u g h a n y p r o g r a m m i n g m o d u l e t o a n y c o m p u t e r v i a t h e s e r i a l d a t a p o r t
. W h e n t h e i s c o n n e c t e d
, n e w s o f t w a r e v e r s i o n s c a n b e l o a d e d i n t o t h e f l a s h m e m o r y
. I n s t r u c t i o n s w i l l b e p r o v i d e d w h e n n e e d e d
. P R O G R A M M I N G W I R E H A R N E S S B A T T E R Y W I R E H A R N E S S T O R X B O S S
i s a l s o t h e C o m b i n a t i o n M o u n t i n g S c r e w
) 6 9
. A c c e s s o r y K i t P a r t N a m e s 9 V o l t B a t t e r y C o n n e c t o r B a t t e r y P a c k B a t t e r y O v e r r i d e C a b l e
9 V B O C
) F i g u r e 4 1 0
. A c c e s s o r y K i t T h e A c c e s s o r y K i t
F i g u r e 4
) i s p r o v i d e d f o r t h e c o n v e n i e n c e o f t h e u s e r
. T h e f o l l o w i n g a r e t h e c o m p o n e n t s p r o v i d e d a n d d e s c r i p t i o n s o f t h e i r f u n c t i o n
. 1 0
. 1 B a t t e r y P a c k T h e t w o b a t t e r y p a c k s w i t h t w o c o n n e c t o r s i s t h e p o w e r s u p p l y f o r t h e I R L
. T h e y c o n n e c t t o t h e B a t t e r y W i r e H a r n e s s l o c a t e d i n t h e I R L b a t t e r y c o m p a r t m e n t
. T h e c o n n e c t o r s a r e p o l a r i z e d
. 1 0
. 2 B a t t e r y O v e r r i d e C a b l e A B a t t e r y O v e r r i d e C a b l e
, 9 V B O C
, i s n e e d e d t o p l u g a s t a n d a r d 9
. 0 V b a t t e r y
, 5 2 2 o r e q u a l
, i n t o t h e j a c k u n d e r t h e r e a d e r i f t h e i n t e r n a l I R L b a t t e r y g o e s d e a d
. T h i s c a b l e i s a v a i l a b l e f r o m R e c o g n i t i o n S o u r c e b u t i s n o t p a r t o f t h i s A c c e s s o r y K i t
. C a l l 6 3 0
7 6 2
4 4 5 0 i f o n e i s n e e d e d
. P L U G w i r e s 7 1 1
. D C M I S e t u p f o r S t a n d
A l o n e M o d e 1 1
. 1 S t a n d
A l o n e M o d e
, D C M I S i m u l a t e s a P a n e l S o t h a t t h e s y s t e m c a n b e t e s t e d a n d e v a l u a t e d w i t h o u t a p a n e l
, t h e p r e s e n c e o f a p a n e l m u s t b e s i m u l a t e d
. W i r i n g a j u m p e r b e t w e e n t h e S t r i k e a n d G r o u n d
t o p t w o
) p i n s o f e a c h 8 p o s i t i o n t e r m i n a l b l o c k
o n h e a d e r s J 3
J 4
) o n t h e D C M I P C B w i l l s i m u l a t e a p a n e l
. S e e F i g u r e 5
. P r o p e r j u m p e r w i r i n g o f J 4 f o r s i m u l a t i n g a p a n e l
, J 3 i s t h e m i r r o r i m a g e
. F i g u r e 5 1 1
. 2 P o w e r t o t h e D C M I i n S t a n d
A l o n e M o d e 1 1
. 2
. 1 L o c a t e t h e 2
p i n h e a d e r
J 1
t o t h e l e f t o f t h e 8
p i n h e a d e r
, J 4
. 1 1
. 2
. 2 P l u g t h e 2
p o s i t i o n t e r m i n a l b l o c k
, h e a d e r
J 1
) a s s h o w n
. S e e F i g u r e 6
. C A U T I O N
T h e v o l t a g e p o l a r i t y c a n n o t b e r e v e r s e d w
o d a m a g e t o t h e u n i t
. 1 1
. 2
. 3 C o n n e c t t h e p a n e l 1 2 V D C s u p p l y t o J 1
. 1 1
. 2
. 4 T h e m i c r o p r o c e s s o r L E D
C R 1 5
) w i l l b l i n k g r e e n a n d t h e L i n k M o d e
S t a n d b y L E D s
C R 9
C R 6
) w i l l i l l u m i n a t e s o l i d g r e e n
J u m p e r W i r e s h o r t i n g t o p t w o p i n s T e r m i n a l B l o c k
o n h e a d e r
8 F i g u r e 6 P r o c e e d t o S e c t i o n 1 3
, R F C h a n n e l S e l e c t i o n
, a n d g o o n
. W h e n d o n e w i t h t h e S t a n d
A l o n e M o d e r e t u r n h e r e t o s t a r t t h e P a n e l
C o n n e c t e d M o d e
. 1 2
. D C M I S e t u p f o r P a n e l
C o n n e c t e d M o d e 1 2
. 1 P a n e l
C o n n e c t e d M o d e
, D C M I W i r e d t o a P a n e l P o w e r i s c o n n e c t e d t o t h e s a m e t w o t e r m i n a l s o f J 1
. P o w e r t o b e s u p p l i e d f r o m a p o w e r s o u r c e i n t h e p a n e l
. A p o w e r s o u r c e f r o m t h e p a n e l m u s t b e 1 2
. 0 V D C n o m i n a l a t 2 5 0 m a
. m i n i m u m
. T h e 8
p o s i t i o n t e r m i n a l b l o c k
F i g
. 5
) p r o v i d e s t h e s i g n a l c o n n e c t i o n s t o t h e p a n e l
. O n e i s o n J 3
o n e o n J 4
. T h e c h a r t b e l o w i n d i c a t e s t h e n a m e s a n d
o r f u n c t i o n s o f e a c h p i n
. F o r c o n n e c t i o n i n s t r u c t i o n s f o r a s p e c i f i c p a n e l
, c a l l 6 3 0
7 6 2
4 4 5 0
. N o t e
S h i e l d e d c a b l e m u s t b e u s e d w h e n w i r i n g a D C M I t o a p a n e l
. J 3
, J 4 N a m e
f u n c t i o n S t r i k e G r o u n d R e q u e s t
t o
E x i t D o o r S t a t u s T r o u b l e D a t a 1
D a t a 0 C l o c k
D a t a G r o u n d W a r n i n g
B e c a u s e e a c h p a n e l i s d i f f e r e n t
, a l w a y s c h e c k t h e p a n e l s i n s t r u c t i o n m a n u a l f o r a p p r o p r i a t e i n t e r f a c e w i r i n g
P A N E L 1 2 V D C S U P P L Y 2
P O S I T I O N T E R M I N A L B L O C K
L E F T P I N
R I G H T P I N O t h e r 6 t e r m i n a l s o f c o n n e c t o r n o t s h o w n 9 1 3
. R F C h a n n e l S e l e c t i o n T h e p r o c e d u r e t o s e l e c t a n d
o r c h a n g e t h e R F C h a n n e l i s t h e s a m e f o r b o t h S t a n d
A l o n e a n d P a n e l
C o n n e c t e d M o d e s
. 1 3
. 1 C o m m u n i c a t i o n s O v e r v i e w T h e W y r e l e s s A c c e s s s y s t e m c o m m u n i c a t e s o n o n e o f 1 5 R F C h a n n e l s
. C h a n n e l s r a n g e b e t w e e n 9 0 2 a n d 9 2 8 M H z
, s e p a r a t e d b y a b o u t 2 M H z
. T h e s y s t e m i s s h i p p e d w i t h t h e d e f a u l t R F C h a n n e l 8 p r e
s e l e c t e d b u t n o t l i n k e d
. O n c e l i n k e d
, t h e s y s t e m w i l l o p e r a t e i n d e f i n i t e l y o n t h a t c h a n n e l
. I t i s n o t n e c e s s a r y t o c h a n g e t h e R F C h a n n e l
. H o w e v e r
, f o r e v a l u a t i o n p u r p o s e s
, a n y o r a l l o f t h e 1 5 c h a n n e l s i n t h e s y s t e m m a y b e t e s t e d
. 1 3
. 2 H o w t o S e t t o a n R F C h a n n e l N o t e t h a t t h e r e a r e f o u r s w i t c h e s o n t h e D i p s w i t c h
S W 7
, n u m b e r e d 1
4
, l e f t t o r i g h t
. S e e c h a r t b e l o w a n d F i g u r e 7
. N u m b e r s a r e i n d i c a t e d o n t h e D i p s w i t c h b e l o w t h e c o r r e s p o n d i n g s w i t c h
. T h e l e f t s w i t c h
1
) h a s a b i n a r y v a l u e o f e i g h t
t h e n e x t s w i t c h
2
) h a s a b i n a r y v a l u e o f f o u r
t h e t h i r d s w i t c h
3
) h a s a v a l u e o f t w o
t h e f o u r t h s w i t c h
4
) h a s a v a l u e o f o n e
. T h e R F C h a n n e l t h e n b e c o m e s t h e s u m o f t h e v a l u e s o f t h e v a r i o u s s w i t c h e s i n t h e d o w n p o s i t i o n
I f t h e s w i t c h i s i n t h e u p p o s i t i o n
, i t s v a l u e i s z e r o
. I f t h e s w i t c h i s d o w n
, i t s v a l u e c o r r e s p o n d s w i t h i t s b i n a r y v a l u e
) V A L U E 0 0 0 0 U P V A L U E 8 4 2 1 D O W N S W I T C H 1 2 3 4 F o r e x a m p l e
, i f R F C h a n n e l 8 i s s e l e c t e d
, t h e p o s i t i o n o f s w i t c h 1 i s d o w n
t h e p o s i t i o n o f s w i t c h 2 i s u p
3 i s u p
4 i s u p
. N o t e
T h e c o n f i g u r a t i o n s f o r C h a n n e l s 0 a n d 1 w i l l b o t h s e l e c t C h a n n e l 1
. 1 0 F i g u r e 7 U s i n g a n o b j e c t w i t h a f i n e p o i n t
a b a l l p o i n t p e n o r s i m i l a r i s a d e q u a t e
) s e t t h e p o s i t i o n s o f t h e f o u r s w i t c h e s f o r t h e d e s i r e d R F C h a n n e l
. W h e n t h e D C M I h a s p o w e r a n d t h e R F C h a n n e l h a s b e e n s e t
, t h e D C M I i s r e a d y t o e n t e r L i n k M o d e
. 1 4
. L i n k M o d e 1 4
. 1 L i n k i n g L i n k i n g i s t h e p r o c e s s t h a t t i e s a D C M I t o a n I R L b y a s s i g n i n g a u n i q u e a d d r e s s t o t h e p a i r
. 1 4
. 2 L i n k P r o c e s s L i n k M o d e a l l o w s a n I R L a n d a D C M I t o l i n k
. W h e n i n L i n k M o d e
, t h e D C M I i s i n i t s r e c e i v e m o d e a w a i t i n g a l i n k r e q u e s t f r o m a n I R L
. T h e I R L i n i t i a t e s l i n k i n g b y s e n d i n g t h i s f i r s t l i n k r e q u e s t w h e n t h e I R L B a t t e r y P a c k i s c o n n e c t e d
. W h e n a D C M I i n t h e L i n k M o d e r e c e i v e s a l i n k r e q u e s t
, t h e D C M I a u t o m a t i c a l l y a s s i g n s a n a d d r e s s r a n d o m l y t o i t s e l f a n d t r a n s m i t s i t t o t h e I R L
. W h e n t h e t w o h a v e t h e s a m e a d d r e s s t h e y a r e t h e n l i n k e d t o g e t h e r
. S i n c e t h i s a d d r e s s i s u n i q u e t o b o t h c o m p o n e n t s
, o t h e r I R L s a n d D C M I s a r e p r e v e n t e d f r o m c o m m u n i c a t i n g w i t h t h e m
. O n c e t h e D C M I a n d t h e I R L a r e l i n k e d
, T h e D C M I a n d t h e I R L t h e n c a n c o m m u n i c a t e u s i n g t h e a s s i g n e d a d d r e s s
. 1 4
. 3 H o w t o p u t t h e D C M I i n t o L i n k M o d e 1 4
. 3
. 1 V e r i f y t h a t t h e D C M I i s p o w e r e d
C R 9 a n d C R 6 a r e l i t s o l i d g r e e n
) a n d t h a t t h e m i c r o p r o c e s s o r i s r u n n i n g
C R 1 5 L E D i s b l i n k i n g g r e e n
. 1 4
. 3
. 2 O n c e t h e R F C h a n n e l h a s b e e n s e t
S e c t i o n 1 3
. 2
, p r e s s t h e T a c t i l e S w i t c h
S 1 f o r I R L A o r S 2 f o r I R L B
. 1 4
. 3
. 3 T h e c o r r e s p o n d i n g L E D s
C R 9 f o r S 1
C R 6 f o r S 2
) w i l l a l t e r n a t e l y f l a s h r e d a n d g r e e n
. T h e D C M I i s n o w i n L i n k M o d e
. U P D O W N S W I T C H
1 1 T h e D C M I r e m a i n s i n L i n k M o d e u n t i l i t r e c e i v e s a l i n k r e q u e s t f r o m a n I R L o r f o r t h i r t y m i n u t e s
, w h i c h e v e r c o m e s f i r s t
. T o a b o r t L i n k M o d e a n d r e t u r n t h e D C M I t o S t a n d b y
, p r e s s t h e s a m e s w i t c h
. S t a n d b y i s i n d i c a t e d w h e n t h e c o r r e s p o n d i n g L E D
C R 9 o r C R 6
) b l i n k s g r e e n
. W h e n t h e D C M I i s p o w e r e d
, t h e R F C h a n n e l i s s e l e c t e d
, a n d t h e D C M I i s i n L i n k M o d e
, t h e s y s t e m i s r e a d y f o r t h e I R L t o i n i t i a t e l i n k i n g
. 1 5
. I R L L i n k i n g t o t h e D C M I v i a B a t t e r y C o n n e c t i o n 1 5
. 1 O v e r v i e w W h e n t h e b a t t e r y p a c k i s c o n n e c t e d
, t h e I R L w i l l a t t e m p t u p t o t h r e e t r a n s m i s s i o n s t o l i n k p r o p e r l y
. T h i s p r o c e s s i s m a d e a p p a r e n t b y a s e r i e s o f b e e p s a n d L E D f l a s h e s f r o m t h e I R L
. S e e S e c t i o n 1 8
. 1 5
. 2 C o n n e c t t h e I R L B a t t e r y P a c k t o I n i t i a t e L i n k i n g t o t h e D C M I 1 5
. 2
. 1 V e r i f y t h e D C M I i s i n L i n k M o d e
L E D C R 9 o r C R 6 f l a s h e s
, a l t e r n a t i n g r e d a n d g r e e n
. 1 5
. 2
. 2 O n t h e I R L
, m a k e s u r e t h e B a t t e r y W i r e H a r n e s s i s a c c e s s i b l e i n t h e B a t t e r y C o m p a r t m e n t
. T h e B a t t e r y W i r e H a r n e s s h a s t w o
, 2
p o s i t i o n c o n n e c t o r s a t t h e e n d
S e e F i g u r e 3
) 1 5
. 2
. 3 C o n n e c t t h e t w o c o n n e c t o r s o n t h e B a t t e r y W i r e H a r n e s s t o t h e t w o c o n n e c t o r s o n t h e B a t t e r y P a c k a s s h o w n i n F i g
. 8
. 1 5
. 2
. 4 T h e I R L i s n o w p o w e r e d
. 1 5
. 2
. 5 O n c e p o w e r e d
, t h e I R L i n i t i a t e s l i n k i n g b y t r a n s m i t t i n g a l i n k r e q u e s t
. 1 5
. 2
. 6 W h e n l i n k i n g i s c o m p l e t e d s u c c e s s f u l l y
, C R 9 o r C R 6 t u r n s s o l i d g r e e n
. 1 5
. 2
. 7 T h e B a t t e r y C o v e r c a n b e c l o s e d a n d s e c u r e d w i t h t h e T o r x s c r e w
S e e F i g u r e 9
) 1 2 F i g u r e 8 F i g u r e 9 1 6
. W h e n a n d H o w t o C h a n g e t h e R F C h a n n e l T h e R F C h a n n e l m a y b e c h a n g e d f o r e v a l u a t i o n p u r p o s e s o r i f t h e s y s t e m e n c o u n t e r s i n t e r f e r i n g t r a n s m i s s i o n s
. W h e n t h e s y s t e m e n c o u n t e r s i n t e r f e r e n c e
m o s t n o t i c e a b l y w h e n t h e s y s t e m a t t e m p t s t o l i n k a n d c a n n o t o r R e q u e s t s
t o
E n t e r f a i l
, t h e R F C h a n n e l s h o u l d b e c h a n g e d t o a l l e v i a t e t h i s c o n d i t i o n
. T o c h a n g e t h e R F C h a n n e l a f t e r t h e s y s t e m i s l i n k e d
, t h e I R L b a t t e r y m u s t b e d i s c o n n e c t e d
. T h e n t h e p o s i t i o n s o f t h e s w i t c h e s o n t h e D C M I d i p s w i t c h
S W 7
) s h o u l d b e c h a n g e d t o t h e n e w d e s i r e d c h a n n e l
. P u s h t h e L i n k M o d e S w i t c h o n t h e D C M I
. A f t e r r e c o n n e c t i n g t h e b a t t e r y p a c k
, t h e I R L s h o u l d b e r e
l i n k e d t o t h e D C M I o n t h e n e w c h a n n e l
. I f t h e I R L a n d t h e D C M I d o n o t r e
l i n k o n t h e n e w f r e q u e n c y
, t h e I R L w i l l r e v e r t t o t h e R F C h a n n e l i t w a s s e t a t p r i o r t o d i s c o n n e c t i n g t h e B a t t e r y P a c k
. 1 7
. U n d e r s t a n d i n g t h e D C M I s L E D I n d i c a t o r s S e v e n L E D s a r e o n t h e P C B
. T h e y a r e C R 1 5 G r e e n
, C R 7 a n d C R 1 0 R e d
, C R 6 a n d C R 9 b o t h G r e e n a n d R e d
. A c t i o n D C M I L E D I n d i c a t i o n C R 1 5 G r n C R 7
, 1 0 R e d C R 6
, 9 G r n
R e d N o r m a l
, M i c r o P r u n n i n g
, P o w e r a p p l i e d B l i n k i n g O f f C o n s t a n t G R N M i c r o P n o t r u n n i n g
, P o w e r m a y b e o n o r o f f O f f O f f C o n s t a n t G R N T r o u b l e s i g n a l
L o w B a t t e r y N o C o m m u n i c a t i o n T a m p e r
, r e a d e r d o o r T a m p e r
, D C M I d o o r B l i n k i n g o n e b l i n k
, p a u s e t w o b l i n k s
, p a u s e t h r e e b l i n k s
, p a u s e f o u r b l i n k s
, p a u s e C o n s t a n t G R N L i n k M o d e B l i n k i n g O f f A l t e r n a t e l y f l a s h G R N
R E D T o r x S c r e w IRL DCMI, 1 3 T r a n s m i t t i n g a m e s s a g e B l i n k i n g O f f 1 R E D f l a s h p e r t r a n s m i s s i o n R e c e i v i n g a m e s s a g e B l i n k i n g O f f B l i n k s O f f m o m e n t a r i l y 1 8
. U n d e r s t a n d i n g t h e I R L s L E D I n d i c a t o r s a n d I n t e r n a l S o u n d e r T h e I R L L E D i s o n t h e f r o n t o f t h e M a g s t r i p e a n d W i e g a n d R e a d e r h o u s i n g s
S e e F i g u r e 2
) o r o n t h e t o p o f t h e P R O X h o u s i n g
. 1 8
. 1 E v e r y t i m e t h e b a t t e r y p a c k s a r e c o n n e c t e d t o t h e I R L
, t h e I R L s L E D a n d s o u n d e r i n d i c a t e t h a t i t i s p o w e r e d
. T h e r e d L E D f l a s h e s o n c e
, f o l l o w e d b y m u l t i p l e g r e e n L E D f l a s h e s
f o u r o n t h e p r e
p r o d u c t i o n u n i t s
) s i g n i f y i n g t h e s o f t w a r e v e r s i o n a n d o n e r e d L E D f l a s h s i g n i f y i n g t h e l o c k m o t o r h a s b e e n d r i v e n t o t h e l o c k e d p o s i t i o n
. T h i s i s a c c o m p a n i e d b y a b e e p
. 1 8
. 2 W h e n t h e I R L s e n d s i t s f i r s t t r a n s m i s s i o n
L i n k r e q u e s t
, t h e L E D s i n d i c a t e t h i s a s w e l l
. T h e g r e e n L E D f l a s h e s o n c e f o l l o w e d b y o n e r e d L E D f l a s h
. T h e L E D s f l a s h i n t h i s s e q u e n c e t h r e e t i m e s o r u n t i l a l i n k t o a D C M I i s e s t a b l i s h e d w h i c h e v e r c o m e s f i r s t
. 1 8
. 3 W h e n t h e I R L l i n k s s u c c e s s f u l l y t o a D C M I
, t h e I R L i n d i c a t e s t h e R F C h a n n e l o n w h i c h i t i s l i n k e d
. T h e g r e e n L E D f l a s h e s a n d t h e I n t e r n a l S o u n d e r b e e p s a c c o r d i n g t o t h e R F C h a n n e l n u m b e r
. F o r e x a m p l e
, i f l i n k i n g h a s b e e n s u c c e s s f u l o n R F C h a n n e l 8
, t h e g r e e n L E D f l a s h e s a n d t h e I n t e r n a l S o u n d e r b e e p s e i g h t t i m e s
. 1 8
. 4 I f
, a f t e r 3 t r a n s m i s s i o n s
, t h e d o e s n o t l i n k t o a t h e r e d L E D f l a s h e s t w i c e a c c o m p a n i e d b y a s i n g l e l o n g b e e p
. T h e I R L r e v e r t s t o i t s p r e v i o u s c h a n n e l a n d a d d r e s s b e f o r e t h e p o w e r w a s d i s c o n n e c t e d
. S e e c h a r t b e l o w f o r c a r d s w i p e d
r e a d
, s w i p e d a n d n o t r e a d
, d o o r u n l o c k
r e l o c k a n d a c c e s s d e n i e d s i g n a l s
. T h e f o l l o w i n g c h a r t o u t l i n e s t h e I R L L E D s a n d I n t e r n a l S o u n d e r i n d i c a t i o n s
. A c t i o n L E D I n d i c a t i o n I R L S o u n d e r I n d i c a t i o n 1 I R L i s p o w e r e d 1 R e d L E D f l a s h
4 G r e e n L E D f l a s h e s
1 R e d L E D f l a s h N o b e e p N o b e e p 1 b e e p 2 I R L s e n d s a l i n k r e q u e s t
u p t o 3 t r a n s m i s s i o n s
, u n t i l i t i s l i n k e d
) 1 G r e e n L E D f l a s h
1 R e d L E D f l a s h e a c h o f 3 t r a n s m i s s i o n s N o b e e p 1 4 3 I R L l i n k e d s u c c e s s f u l l y a n d a n n o u n c e s t h e R F C h a n n e l o n w h i c h i t i s l i n k e d G r e e n L E D f l a s h e s
n u m b e r e q u a l t o t h e R F C h a n n e l
) B e e p s
n u m b e r e q u a l t o t h e R F C h a n n e l
) 4 I R L n o t l i n k e d s u c c e s s f u l l y 2 R e d L E D f l a s h e s 1 l o n g b e e p C a r d s w i p e
, n o t r e a d N o n e N o n e C a r d s w i p e d a n d r e a d N o n e 1 b e e p F o l l o w e d b y
5 N o c o m m u n i c a t i o n s 1 R e d f l a s h N o n e D o o r u n l o c k 1 G R N f l a s h N o n e A c c e s s d e n i e d 2 R E D f l a s h e s 1 b e e p D o o r r e l o c k s 1 R E D f l a s h 1 b e e p M a g s t r i p e
, W i e g a n d a n d P r o x r e a d e r s w i l l u s e t h e s a m e L E D
b e e p i n d i c a t o r s
. 1 9
. O p e r a t i n g t h e W y r e l e s s A c c e s s S y s t e m 1 9
. 1 O v e r v i e w O n c e t h e I R L a n d t h e D C M I a r e l i n k e d
, t h e W i r e l e s s A c c e s s s y s t e m i s r e a d y t o b e o p e r a t e d
. A c a r d s w i p e i s r e q u i r e d t o o p e r a t e t h e s y s t e m
. W h e n a c a r d i s s w i p e d t h e I R L t r a n s m i t s a R e q u e s t
t o
U n l o c k
. A v a l i d c a r d m u s t b e u s e d f o r a s u c c e s s f u l R e q u e s t
t o
U n l o c k
. I n S t a n d
A l o n e O p e r a t i o n
, a v a l i d c a r d i s a n y m a g n e t i c s t r i p e c a r d w i t h T r a c k 2 d a t a
A T M c a r d s
, c r e d i t c a r d s
, e t c
. I n P a n e l
C o n n e c t e d O p e r a t i o n
, a v a l i d c a r d i s a m a g s t r i p e c a r d t h a t h a s b e e n v a l i d a t e d b y t h e a c c e s s c o n t r o l p a n e l
. I n S t a n d
A l o n e O p e r a t i o n
, t h e D C M I r e c e i v e s t h i s t r a n s m i t t e d r e q u e s t a n d w i l l v a l i d a t e t h e c a r d
. O n c e v a l i d a t e d
, t h e D C M I w i l l t r a n s m i t a s i g n a l t o t h e I R L t o u n l o c k
. T h e I R L w i l l u n l o c k a n d t h e n r e l o c k
. I n P a n e l
C o n n e c t e d O p e r a t i o n
, t h e D C M I r e c e i v e s t h e t r a n s m i t t e d R e q u e s t
t o
U n l o c k f r o m t h e I R L a n d t h e n f o r w a r d s t h e r e q u e s t t o t h e c o n t r o l p a n e l
. I f t h e c a r d u s e d i s v a l i d a t e d
, t h e c o n t r o l p a n e l w i l l s i g n a l b a c k t o t h e D C M I a c o m m a n d t o u n l o c k
. T h e D C M I t h e n t r a n s m i t s t h e u n l o c k c o m m a n d t o t h e I R L
. T h e I R L w i l l u n l o c k a n d t h e n r e
l o c k
. 1 9
. 2 C a r d S w i p i n g N O T E
O n e a s p e c t o f t h e W y r e l e s s A c c e s s P r e
P r o d u c t i o n S y s t e m t h a t w i l l c h a n g e i n p r o d u c t i o n u n i t s i s t h e M a g s t r i p e r e a d e r
. T h e M a g s t r i p e r e a d e r h e a d w a s i n a d v e r t e n t l y p l a c e d o n t h e w r o n g s i d e o f t h e M a g s t r i p e r e a d e r
Request-to-Unlock IRL 1 5 C a r d s n e e d t o b e s w i p e d i n r e v e r s e
. N o r m a l l y
, t h e f r o n t o f t h e c a r d w o u l d f a c e t h e l e f t s i d e
F i g u r e 1 0
) a n d t h e m a g n e t i c s t r i p e w o u l d b e r e a d o n t h e r i g h t
. B u t o n t h i s u n i t
, c a r d s s h o u l d b e s w i p e d w i t h t h e f r o n t o f t h e c a r d f a c i n g t h e r i g h t a n d t h e m a g n e t i c s t r i p e f a c i n g t h e l e f t
F i g u r e 1 1
) T h e r e a d e r h e a d w i l l b e c o r r e c t l y o r i e n t e d i n t h e p r o d u c t i o n v e r s i o n
. I n s e r t t h e c a r d w i t h t h e m a g n e t i c s t r i p e o n t h e l e f t
F i g u r e 1 1
) a n d t h e n s l i d e i t d o w n k e e p i n g t h e b a c k e d g e o f t h e c a r d f i r m l y a g a i n s t t h e b a c k o f t h e r e a d e r s s l o t t h r o u g h o u t t h e e n t i r e s w i p e
. F i g u r e 1 0 F i g u r e 1 1 1 9
. 3 I n d i c a t i o n s o f a S u c c e s s f u l C a r d S w i p e W h e n e v e r a c a r d i s s w i p e d a n d a t l e a s t 8 b i t s o f i n f o r m a t i o n a r e r e a d f r o m t h e c a r d
, a b e e p i s s o u n d e d a n d t h e I R L t r a n s m i t s a R e q u e s t t o u n l o c k
. A s u c c e s s f u l c a r d s w i p e d o e s n o t a l w a y s r e s u l t i n a n u n l o c k
. M o r e t h a n 8 b i t s a r e n e e d e d f o r a v a l i d u n l o c k r e q u e s t
. S o a l l r e q u i r e d b i t s m u s t b e r e a d
. A b e e p m a y b e g i v e n b e c a u s e 8 b i t s a r e r e a d
, b u t m o r e b i t s a r e n e e d e d f o r a n u n l o c k
. I f a n i n v a l i d c a r d i s s w i p e d c o r r e c t l y
, t h e s y s t e m w i l l r e l a y t h e i n f o r m a t i o n b u t t h e d o o r w i l l r e m a i n l o c k e d
. 1 9
. 4 I n d i c a t i o n o f a n U n s u c c e s s f u l C a r d S w i p e T h e b e s t i n d i c a t i o n o f a n u n s u c c e s s f u l c a r d s w i p e i s w h e n t h e I R L I n t e r n a l S o u n d e r d o e s n o t b e e p a f t e r a c a r d s w i p e
. M o s t l i k e l y
, t h e c a r d w a s c o c k e d o r n o t s w i p e d w i t h i t s b a c k e d g e a g a i n s t t h e r e a d e r s l o t b a c k f o r t h e e n t i r e s w i p e
. I t s h o u l d b e s w i p e d a g a i n
. 1 9
. 5 I n d i c a t i o n s o f a S u c c e s s f u l R e q u e s t
t o
U n l o c k
C a r d S w i p e
) T h e i n d i c a t i o n o f a s u c c e s s f u l i s w h e n t h e u n l o c k s
. M a g s t r i p e C a r d m u s t b e s w i p e d i n t h i s o r i e n t a t i o n 1 6 A p p r o x i m a t e l y o n e s e c o n d a f t e r a v a l i d c a r d s w i p e
, t h e I R L g r e e n L E D w i l l f l a s h o n c e a n d t h e I R L w i l l u n l o c k
R e q u e s t s t o u n l o c k a r e
. s e n t 3 t i m e s T h e D C M I L E D
, C R 6 o r C R 9
, i n d i c a t e s w h e n i t i s r e c e i v i n g t h e R e q u e s t t o u n l o c k f r o m t h e I R L b y t u r n i n g o f f m o m e n t a r i l y
l o o k s l i k e a f l i c k e r
. T h e D C M I w i l l t r a n s m i t a n a c k n o w l e d g e m e n t t o t h e I R L t h a t i t r e c e i v e d t h e t r a n s m i s s i o n a n d s e n d s t h e d a t a t o t h e p a n e l
. A f t e r t h a t t h e I R L r e
q u e r i e s u p t o 5 t i m e s t o i n q u i r e i f t h e r e i s a r e s p o n s e f r o m t h e p a n e l t o u n l o c k t h e d o o r
. O n c e t h e D C M I r e c e i v e s a r e s p o n s e f r o m t h e p a n e l i t t r a n s m i t s i t b a c k t o t h e I R L i n r e s p o n s e t o o n e o f t h e I R L r e
q u e r i e s
. T h e D C M I L E D w i l l f l a s h r e d o n c e f o r e v e r y t i m e i t s e n d s a r e s p o n s e t o t h e I R L t h e n r e v e r t s t o s o l i d g r e e n
. T h e I R L t r a n s m i t s i t s r e q u e s t u p t o t h r e e t i m e s o r u n t i l i t i s v a l i d a t e d b y t h e p a n e l
R e l o c k R e l o c k t i m e i s c o n f i g u r a b l e f r o m 1 t o 2 5 5 s e c o n d s
. A f t e r t h e p r e s e t t i m e h a s e l a p s e d
, t h e I R L r e l o c k s a n d t h e r e d L E D w i l l f l a s h o n c e a n d t h e I n t e r n a l S o u n d e r w i l l b e e p o n c e
. 1 9
. 6 I n d i c a t i o n s o f a n U n s u c c e s s f u l R e q u e s t
t o
U n l o c k
C a r d S w i p e
) T h e b e s t i n d i c a t i o n o f a n u n s u c c e s s f u l R e q u e s t
t o
U n l o c k i s w h e n t h e I R L r e m a i n s l o c k e d
. H o w e v e r
, t h e I R L L E D a n d I n t e r n a l S o u n d e r a l s o i n d i c a t e s a n u n s u c c e s s f u l R e q u e s t
t o
U n l o c k
. A f t e r a n i n v a l i d c a r d s w i p e
u n s u c c e s s f u l R e q u e s t
t o
U n l o c k
, t h e I R L r e d L E D f l a s h e s t w i c e a n d t h e I n t e r n a l S o u n d e r b e e p s o n c e
. T h e I R L r e m a i n s l o c k e d
. I n P a n e l
C o n n e c t e d O p e r a t i o n
, a f t e r a n u n s u c c e s s f u l R e q u e s t
t o
U n l o c k
, t h e p a n e l s h o u l d i n d i c a t e o n e o f t w o r e a s o n s w h y t h e r e q u e s t w a s u n s u c c e s s f u l
. O n e i s a D e n i e d R e q u e s t w h e r e t h e c a r d u s e d w a s a r e c o g n i z e d c a r d b u t w i t h o u t t h e a u t h o r i t y t o u n l o c k t h e s p e c i f i c d o o r o r w i t h o u t t h e a u t h o r i t y t o u n l o c k t h e s p e c i f i c d o o r a t t h a t s p e c i f i c t i m e
. T h e o t h e r i s a n U n r e c o g n i z e d C a r d w h e r e t h e c a r d u s e d w a s a n i n v a l i d a n d u n r e c o g n i z a b l e c a r d
i
. e
, n o t p a r t o f t h e s y s t e m
. 2 0
. O t h e r S o f t w a r e F e a t u r e s S e n s e s a n d r e p o r t s d o o r p o s i t i o n t o t h e p a n e l
. P e r i o d i c a l l y r e p o r t s t o p a n e l f o r H o u s e k e e p i n g u p d a t e s
, 1
, 2
, 5 o r 1 5 m i n u t e s i n t e r v a l s
, c o n f i g u r a b l e
. B a t t e r y l i f e i s a f u n c t i o n o f t h i s t i m e p e r i o d a n d n u m b e r o f c a r d s w i p e s
. R e q u e s t
t o
E x i t
. 1 7 B a t t e r y L i f e T a b l e 1 0 m i n
. 5 m i n
. 1 0 m i n
. 2 m i n
. 5 m i n
. 5 m i n
. 1 5 m i n
. m i n
. 1
. 0 m i n
. 0 1 0
, 0 0 0 2 0
, 0 0 0 3 0
, 0 0 0 4 0
, 0 0 0 5 0
, 0 0 0 2 1
. P r e
P r o d u c t i o n S y s t e m L i m i t a t i o n s T h e p r e
p r o d u c t i o n s y s t e m o f E n g i n e e r i n g P i l o t R u n u n i t s p r o v i d e s a n e a r l y a s s e s s m e n t o f p e r f o r m a n c e c a p a b i l i t i e s
. T h e f o l l o w i n g i s a n o u t l i n e o f l i m i t a t i o n s o f t h e p r e
p r o d u c t i o n s y s t e m
. T h e s e w i l l b e a v a i l a b l e i n p r o d u c t i o n
. F C C D o e s n o t h a v e F C C a p p r o v a l
. U L D o e s n o t h a v e U L a p p r o v a l
. S h o c k a n d V i b r a t i o n S h o c k a n d v i b r a t i o n t e s t s h a v e n o t b e e n c o m p l e t e d
. L i n k M o d e A t t e n u a t e d b y 3 d B F e a t u r e h a s n o t b e e n i m p l e m e n t e d
. L o w B a t t e r y I n d i c a t i o n a t t h e P a n e l F e a t u r e h a s n o t b e e n i m p l e m e n t e d
. I n t e r n a l C a c h e M e m o r y F e a t u r e i s n o t i m p l e m e n t e d
. I R L R e a d e r T a m p e r S w i t c h F e a t u r e h a s n o t b e e n i m p l e m e n t e d
. D C M I T a m p e r S w i t c h F e a t u r e h a s n o t b e e n i m p l e m e n t e d
. R S 4 8 5 C o m m u n i c a t i o n P r o t o c o l t o t h e P a n e l S c h e d u l e d f o r R e l e a s e 2
. 2 2
. C a r e a n d U s a g e A l w a y s o p e r a t e t h e W y r e l e s s A c c e s s P r e
P r o d u c t i o n S y s t e m w i t h i n i n s t r u c t i o n s a n d s p e c i f i c a t i o n s d e s c r i b e d i n t h i s m a n u a l
. K e e p t h e D C M I d o o r a n d I R L b a t t e r y c o m p a r t m e n t c l o s e d w h e n i n u s e
. D o n o t u s e t h e s y s t e m o u t d o o r s
. D o n o t p a i n t a n y p a r t
, e s p e c i a l l y t h e D C M I a n t e n n a o r I R L A n t e n n a C o v e r
. 2 3
. S p e c i f i c a t i o n s
2 3
. 1 B o t h C o m p o n e n t s 2 3
. 1
. 1 T e m p e r a t u r e
1 0 C t o
6 0 C 2 3
. 1
. 2 H u m i d i t y 2 0
R H t o 9 5
R H
, n o n
c o n d e n s i n g 2 3
. 2 I R L 2 3
. 2
. 1 V o l t a g e 4
. 7 5 1 3
. 2 V D C 2 3
. 2
. 2 S l a m 1 0
, 0 0 0 c y c l e s
, 2 0 t o 3 0 G p e r A N S I
B H M A A 1 5 6
. 2 5
, s e c t i o n 6
. 3
. 5
. 1 2 3
. 2
. 3 D o o r S l a m 1 0 c y c l e s
, 1 0 0 0 G m i n i m u m
. 2 3
. 3 D C M I 2 3
. 3
. 1 V o l t a g e 1 2 V D C
1 0
1 5
2 3
. 3
. 2 C u r r e n t 2 5 0 m a r m s m a x
. Y e a r s 4 3 2 1 0 Contact Eric Gonzales at 630-762-4462 or Larry Brooks at 630-762-4471. 1 8 2 4
. T r o u b l e s h o o t i n g T h e f o l l o w i n g c h a r t o u t l i n e s s e v e r a l s y m p t o m s a n d t h e i r c o m m o n f i x
. I f
, a f t e r g o i n g t h r o u g h t h e s e i n s t r u c t i o n s
, t h e s y s t e m i s s t i l l e x p e r i e n c i n g d i f f i c u l t i e s
, d o n o t a t t e m p t t o f i x
. S y m p t o m C a u s e A c t i o n T h e L E D C R 1 5 i s n o t b l i n k i n g a n d C R 9
C R 6 d o n o t i l l u m i n a t e s o l i d g r e e n w h e n p o w e r i s s u p p l i e d t o t h e D C M I
. P o w e r h a s n o t b e e n s u p p l i e d c o r r e c t l y o r t h e m i c r o p r o c e s s o r i s n o t f u n c t i o n i n g
. C h e c k t h e p o l a r i t y o f t h e p a n e l s u p p l y
. I f w r o n g t h e f u s e m u s t b e r e p l a c e d
. R e p l a c e w i t h a 3
8 A
, 2 5 0 V
, 2 A G
, f a s t a c t i n g f u s e
. T h e p o l a r i t y o f t h e p a n e l p o w e r s u p p l y i s c o r r e c t a n d t h e s y m p t o m p e r s i s t s
. S e e a b o v e
. C h e c k t h e v o l t a g e
. T h e v o l t a g e m u s t b e b e t w e e n 5
. 0 a n d 1 2
. 0 V D C
. D o n o t e x c e e d 1 3
. 2 v o l t s
. D C M I S y m p t o m s T h e v o l t a g e i s a t o r f e w e r t h a n 1 3
. 2 v o l t s a n d t h e s y m p t o m p e r s i s t s
. S e e a b o v e
. C o n t a c t E r i c G o n z a l e s a t 6 3 0
7 6 2
4 4 6 2 o r L a r r y B r o o k s a t 6 3 0
7 6 2
4 4 7 1
. T h e I R L L E D s d o n o t f l a s h a n d t h e I n t e r n a l S o u n d e r d o e s n o t b e e p w h e n p o w e r i s a p p l i e d t o t h e I R L
. T h e b a t t e r y p a c k i s n o t s u p p l y i n g p o w e r t o t h e I R L
. C h e c k t h a t t h e b a t t e r y p a c k i s n e w a n d h a s b e e n c o n n e c t e d p r o p e r l y
. T h e b a t t e r y p a c k i s g o o d a n d h a s b e e n c o n n e c t e d p r o p e r l y a n d t h e s y m p t o m p e r s i s t s
. S e e a b o v e
. C o n t a c t E r i c G o n z a l e s a t 6 3 0
7 6 2
4 4 6 2 o r L a r r y B r o o k s a t 6 3 0
7 6 2
4 4 7 1
. T h e I R L L E D S d o n o t f l a s h a n d t h e I n t e r n a l S o u n d e r d o e s n o t b e e p t o a n n o u n c e t h e R F C h a n n e l w h e n a t t e m p t i n g t o l i n k
. T h e s y s t e m i s n o t l i n k i n g p r o p e r l y
. C h e c k t h a t t h e D C M I i s p r o p e r l y i n L i n k M o d e b e f o r e p o w e r i s s u p p l i e d t o t h e I R L
. T h e D C M I i s p r o p e r l y i n L i n k M o d e a n d t h e s y m p t o m p e r s i s t s
. S e e a b o v e
. C o n t a c t E r i c G o n z a l e s a t 6 3 0
7 6 2
4 4 6 2 o r L a r r y B r o o k s a t 6 3 0
7 6 2
4 4 7 1
. T h e I R L d o e s n o t u n l o c k a f t e r a c a r d s w i p e
. T h e I R L a n d t h e D C M I a r e n o t c o m m u n i c a t i n g p r o p e r l y
. A v a l i d c a r d i s u s e d a n d t h e s y m p t o m p e r s i s t s
. S e e a b o v e
. I f i n S t a n d
A l o n e O p e r a t i o n
, c h e c k t h a t t h e t e r m i n a l b l o c k h a s b e e n a t t a c h e d p r o p e r l y
. I f i n P a n e l
C o n n e c t e d O p e r a t i o n
, c h e c k t h a t t h e w i r i n g t o t h e p a n e l i s c o r r e c t
. I R L S y m p t o m s T h e c a r d i s v a l i d a n d t h e t e r m i n a l b l o c k i s a t t a c h e d p r o p e r l y o r p a n e l c o n n e c t i o n i s c o r r e c t a n d t h e s y m p t o m p e r s i s t s
. S e e a b o v e
. C o n t a c t E r i c G o n z a l e s a t 6 3 0
7 6 2
4 4 6 2 o r L a r r y B r o o k s a t 6 3 0
7 6 2
4 4 7 1
. 1 9 2 5
. O t h e r I n s t a l l a t i o n R e q u i r e m e n t s T h e D C M I m u s t b e i n s t a l l e d b y q u a l i f i e d p r o f e s s i o n a l o r c o n t r a c t o r s i n a c c o r d a n c e w i t h F C C P a r t 1 5
. 2 0 3 i n d i c a t e d b e l o w
. C o d e o f F e d e r a l R e g u l a t i o n s T i t l e 4 7 T e l e c o m m u n i c a t i o n s P a r t 1 5
. 2 0 3 A n t e n n a R e q u i r e m e n t A n i n t e n t i o n a l r a d i a t o r s h a l l b e d e s i g n e d t o e n s u r e t h a t n o a n t e n n a o t h e r t h a n t h a t f u r n i s h e d b y t h e r e s p o n s i b l e p a r t y s h a l l b e u s e d w i t h t h e d e v i c e
. T h e u s e o f a p e r m a n e n t l y a t t a c h e d a n t e n n a o r o f a n a n t e n n a t h a t u s e s a u n i q u e c o u p l i n g t o t h e i n t e n t i o n a l r a d i a t o r s h a l l b e c o n s i d e r e d s u f f i c i e n t t o c o m p l y w i t h t h e p r o v i s i o n s o f t h i s s e c t i o n
. T h e m a n u f a c t u r e r m a y d e s i g n t h e u n i t s o t h a t a b r o k e n a n t e n n a c a n b e r e p l a c e d b y t h e u s e r
, b u t t h e u s e o f a s t a n d a r d a n t e n n a j a c k o r e l e c t r i c a l c o n n e c t o r i s p r o h i b i t e d
. T h i s r e q u i r e m e n t d o e s n o t a p p l y t o c a r r i e r c u r r e n t d e v i c e s o r t o d e v i c e s o p e r a t e d u n d e r t h e p r o v i s i o n s o f S e c
. 1 5
. 2 1 1
, S e c
. 1 5
. 2 1 3
, S e c
. 1 5
. 2 1 7
, S e c
. 1 5
. 2 1 9
, o r S e c
. 1 5
. 2 2 1
. F u r t h e r
, t h i s r e q u i r e m e n t d o e s n o t a p p l y t o i n t e n t i o n a l r a d i a t o r s t h a t m u s t b e p r o f e s s i o n a l l y i n s t a l l e d
, s u c h a s p e r i m e t e r p r o t e c t i o n s y s t e m s a n d s o m e f i e l d d i s t u r b a n c e s e n s o r s
, o r t o o t h e r i n t e n t i o n a l r a d i a t o r s w h i c h
, i n a c c o r d a n c e w i t h S e c
. 1 5
. 3 1
d
, m u s t b e m e a s u r e d a t t h e i n s t a l l a t i o n s i t e
. H o w e v e r
, t h e i n s t a l l e r s h a l l b e r e s p o n s i b l e f o r e n s u r i n g t h a t t h e p r o p e r a n t e n n a i s e m p l o y e d s o t h a t t h e l i m i t s i n t h i s p a r t a r e n o t e x c e e d e d
1 2 3 | Operational Manual | Users Manual | 973.25 KiB | / December 01 2004 |
PPPRRREEELLLIIIMMMIIINNNAAARRRYYY CONFIGURING & OPERATING INSTRUCTIONS WYRELESS ACCESS SYSTEM
(WAS) 3820 Stern Avenue St. Charles, IL 60174 Phone: 630-762-4450 Fax: 630-762-4455 P/N: M053-xxx-x001.1 CONFIGURING & OPERATING INSTRUCTIONS NOTE: This manual is intended to be used after the Wyreless Access Modules have been installed. Each Wyreless Access module has its own installation manual. Use this manual to configure and operate your system. TABLE OF CONTENTS 1. Wyreless Access System (WAS)......................................................................................................................4 2. Panel Interface Module (PIM)............................................................................................................................5 2.1 How to determine the version of PIM PCB...................................................................................................6 2.2 The PIM Indicators........................................................................................................................................9 2.3 How to Set an RF Channel ..........................................................................................................................10 2.4 Putting the PIM into Link Mode..................................................................................................................10 2.5 What Happens if the PIM Loses DC Power ................................................................................................10 2.6 Using the PIM Reset Switch........................................................................................................................11 2.7 PIM Tamper Switch Operation....................................................................................................................11 2.8 Using the PIM Programming Connector .....................................................................................................11 3. Panel Interface Module Expander (PIME) .....................................................................................................12 4. Modular Integrated Reader Lock (MIRL)......................................................................................................13 4.1 The MIRL Audio/Visual Indicators.............................................................................................................13 4.2 Linking the MIRL to a WPIM .....................................................................................................................14 4.3 Testing the MIRL ........................................................................................................................................16 4.4 Installing/Replacing the MIRL Battery Pack...............................................................................................16 4.5 Battery Override ..........................................................................................................................................17 4.6 Re-linking an MIRL and WPIM..................................................................................................................17 4.7 Changing the RF Channel............................................................................................................................17 5. Wireless Reader Interface (WRI).....................................................................................................................18 5.1 The WRI Visual Indicators..........................................................................................................................19 5.2 Linking to the WPIM by Powering or Resetting the WRI...........................................................................20 5.3 Testing the WRI...........................................................................................................................................20 5.4 Re-linking a WRI and WPIM ......................................................................................................................21 5.5 Changing the RF Channel............................................................................................................................21 6. Wireless Integrated Strike Interface (WISI)...................................................................................................22 6.1 The WISI Audio/Visual Indicators ..............................................................................................................23 6.2 Linking to the WPIM by Powering the WISI ..............................................................................................23 6.3 Testing the WISI..........................................................................................................................................24 P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 2 of 44 6.4 Replacing the WISI Battery Pack, BP12V-001 ...........................................................................................24 6.5 Battery Override ..........................................................................................................................................25 6.6 Re-linking an WISI and WPIM ...................................................................................................................25 6.7 Changing the RF Channel............................................................................................................................25 7. Wireless Universal Strike Interface (WUSI) ...................................................................................................27 7.1 The WUSI Visual Indicators........................................................................................................................28 7.2 Linking to the WPIM by Powering the WUSI.............................................................................................28 7.3 Testing the WUSI ........................................................................................................................................29 7.4 Re-linking a WUSI and WPIM....................................................................................................................30 7.5 Changing the RF Channel............................................................................................................................30 8. Wireless Portable Reader (WPR).....................................................................................................................31 8.1 The WPR Audio/Visual Indicators ..............................................................................................................32 8.2 Turning the WPR On...................................................................................................................................32 8.3 Linking or Re-Linking to the WPIM by Powering the WPR.......................................................................32 8.4 Testing the WPR..........................................................................................................................................33 8.5 Replacing the WPR Battery Pack, BP12V-001 ...........................................................................................34 8.6 Changing the RF Channel............................................................................................................................35 9. Wireless Contact Monitor (WCM)...................................................................................................................36 9.1 The WCM Visual Indicators........................................................................................................................37 9.2 Linking to the WPIM by Resetting the WCM .............................................................................................37 9.3 Replacing the WCM Battery Pack, BP12V-001..........................................................................................38 9.4 Re-linking an WCM and WPIM..................................................................................................................39 9.5 Changing the RF Channel............................................................................................................................39 10. Other Important Information.......................................................................................................................40 Knowing When to Change the RF Channel.............................................................................................40 10.1 Configuring the Wyreless AccessTM System ...........................................................................................40 10.2 10.3 Extended Unlock .....................................................................................................................................40 10.4 Why Swipe a Card When the Power Is Disconnected? ...........................................................................41 Contacting Recognition Source ....................................................................................................................42 FCC Compliance & Warnings......................................................................................................................43 12.1 FCC Compliance .....................................................................................................................................43 12.2 Warnings..................................................................................................................................................43 Revision History.............................................................................................................................................44 11. 12. 13. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 3 of 44 1. Wyreless Access System (WAS) Every access control system that uses Wyreless AccessTM contains two different types of modules (Figure 1-1):
at least one Wyreless Panel Interface Module (WPIM), and at least one Wyreless Access Point Module (WAPM) Recognition Sources product line contains several different expressions of each module (Table 1-1). Figure 1-1 Wyreless Access System Block Diagram Wyreless Access Module Name Acronym Panel Interface Module Panel Interface Module Expander Modular Integrated Reader Lock Wireless Reader Interface Wireless Integrated Strike Interface*
Wireless Universal Strike Interface Wireless Portable Reader*
Wireless Contact Monitor*
*Not evaluated by UL. PIM PIME MIRL WRI WISI WUSI WPR WCM Type WPIM WPIM WAPM WAPM WAPM WAPM WAPM WAPM Manual Section Page 2 3 4 5 6 7 8 9 5 12 13 18 22 27 31 36 Table 1-1 Recognition Source Wyreless Access Product Line The WPIM is wired to the access control panel and ideally is installed very close to the access control panel. The WPIMs installation location is determined by the location of the WAPMs with which it will communicate using RF. The WAPM is installed at the access point where access will be controlled and/or monitored. Depending on the application and which WAPM is used, some wiring at the access control point may be required. Regardless of which WPIM or WAPM module is used, the communication link between the WPIM and WAPM is always RF. This manual describes the configuration and operation of all the WPIMs and WAPMs in the Recognition Source Wyreless Access Product Line. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 4 of 44 2. Panel Interface Module (PIM) The Panel Interface Module (PIM) is a product in the Recognition Sources Wyreless Panel Interface Module
(WPIM) category. The PIM is the wireless interface to an access control panel. Table 2-1 & Table 2-2 show all the PIM sales models and their major specifications. Sales Model PIM-OTD Closed Enclosure Opened Enclosure Extender Antenna PIME-OTD internal c or remote
(ANT-REMOTE)
(ANT-6DB-FLAT) Table 2-1 PIM Enclosure Variations P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 5 of 44 MODEL ENCLOSURE MAXIMUM NUMBER OF WAPMs PIM-OTD PIM-OTD-485 PIME-OTD ANT-REMOTE ANT-6DB-PANEL plastic plastic n/a plastic plastic 2 16 2 n/a n/a LOCATION ACCESS CONTROL PANEL INTERFACE/DESCRIPTION indoor indoor indoor indoor outdoor indoor outdoor Magnetic (clock & data) or Wiegand (data1/data0) RS485 Magnetic (clock & data) or Wiegand (data1/data0) Optional remote omni-directional antenna (0 DB gain) Optional remote directional panel antenna (6 DB gain) 2.1 How to determine the version of PIM PCB Table 2-2- PIM Sales Model Table There are two versions of the PIM printed circuit board (PCB): RS232 (Figure 2-1) and RS485 (Figure 2-2). The version of PIM PCB being installed can be identified by observing which connectors are installed on the PCB. Compare the board being installed to Figure 2-1 and Figure 2-2. 2.1.1 RS232 PIM PCB (Figure 2-1) If the RS232, 9-pin connector, J5, is installed and the RS485, 5-pin terminal block, J7, is missing then it is a RS232 PIM PCB 2.1.2 RS485 PIM PCB (Figure 2-2) The RS485 PIM PCB can be uniquely identified in one of two ways:
If the RS232, 9-pin connector, J5, is installed and the RS485, 5-pin terminal block, J7, is installed it is a RS485 PIM PCB If the Access Point A, 8-pin panel connector, J3 and the Access Point B, 8-pin panel connector, J4, are missing it is a RS485 PIM PCB P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 6 of 44 Figure 2-1 RS232 PIM & PIME Printed Circuit Board (PCB) P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 7 of 44 Figure 2-2 RS485 PIM & PIME Printed Circuit Board (PCB) P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 8 of 44 2.2 The PIM Indicators There are five LEDs on the PIM PCB: CR15 (green), CR7 and CR10 (red), CR6 and CR9 (green and red). These LEDs indicate the current status of the PIM (Table 2-3) and the WAPMs linked to it. Condition LED Indication CR 15
(green) CR7, 10
(red) CR6, 9
(green red) Normal operation, PIM is powered &
the microprocessor is running Tamper On
(Door Open) Tamper Off 2 PIM is not powered or PIM is defective WAPM Trouble: Low Battery WAPM Trouble: No Communication WAPM Trouble: Reader Tamper WAPM Trouble: Lock Motor Stall blinking on off on NA NA NA 1 blink 2 blinks 3 blinks 4 blinks green green NA NA Link Access Point A Link Access Point B blinking blinking NA NA 1 3 4 5 CR9 flash green & red CR6 flash green & red Green flash on every good transmission-
Red flash on any bad transmission. Goes on for about 20 seconds. 1 red flash per transmission blinks off momentarily 6 Packet-Error-Rate test during linking blinking NA 7 8 PIM Transmitting a Message blinking PIM Receiving a Message blinking NA NA Table 2-3 PIM LED Indicators P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 9 of 44 2.3 How to Set an RF Channel One of fifteen RF channels can be set using DIP switch SW7 on the PIM (Figure 2-1 or Figure 2-2). Table 2-4 shows how to set SW7 to select the desired RF channel:
Switch 3 Switch 1 Switch 2 Switch 4 Channel 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 up up up up up up up up down down down down down down down down up down up down up down up down up down up down up down up down Table 2-4 DIP Switch Setting to Select the RF Channel up up down down up up down down up up down down up up down down up up up up down down down down up up up up down down down down NOTE: The first two switch settings select Channel 1. When the PIM is wired to the panel, power is applied, and the RF Channel is set, the PIM is ready to enter Link Mode. 2.4 Putting the PIM into Link Mode The Link Mode allows 2 WAPMs to be linked to a PIM. Only one WAPM can be linked at a time. 2.4.1 Once the RF Channel has been set (Section 2.3) on the PIM, press and release switch S1 to link Access Point A (AP A) or switch S2 to link Access Point B (AP B). 2.4.2 The corresponding PIM LED (CR9 for S1; CR6 for S2) flashes red and green. This indicates that the PIM is in Link Mode. To abort Link Mode, press the same switch again. When the PIM is powered, the RF Channel is set, and the PIM is in Link Mode, the system is ready for the WAPM to initiate linking. Now, proceed to the appropriate section of this manual to link the desired WAPM to this PIM. 2.5 What Happens if the PIM Loses DC Power All of the configuration and linking information is stored in non-volatile memory in the PIM. Therefore if PIM DC power is lost or cycled, upon restoring DC power, the PIM will continue operation with the same configuration and linking information. There is no need to re-configure or re-link. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 10 of 44 2.6 Using the PIM Reset Switch The Reset Switch, S3 (Figure 2-1 or Figure 2-2), is used if the PIM does not seem to be working properly. Pressing the Reset Switch has the same effect as cycling DC power to the PIM. 2.7 PIM Tamper Switch Operation The PIM Tamper Switch, SW1 (Figure 2-1 or Figure 2-2), senses if the PIM enclosure door is open or closed. PIM Enclosure Door PIM LED CR15 PIM Access Point A Trouble Signal*
PIM Access Point B Trouble Signal*
constant green inactive inactive Extended Unlock for Access Point A
Access Point B works if enabled blinking green active active does not work even if enabled
*this assumes that no other trouble is present from either Access Point closed
(i.e. no tamper) open
(i.e. tamper) Table 2-5 PIM Tamper Switch Operation The Trouble signal is asserted (activated) for both PIM Access Points when a PIM enclosure door is opened. Any PIM enclosure door opening, even if for maintenance, is considered a tamper condition. When the PIM enclosure door is open the Extended Unlock feature (section 10.3) will not work (i.e. temporarily disabled) even if the feature is configured to be enabled under normal operation (i.e. no PIM tamper). This was done to makes system testing, maintenance, and commissioning easier. 2.8 Using the PIM Programming Connector The PIM Programming Connector, J2 (Figure 2-1 or Figure 2-2) is used to install a new version of the PIM firmware into the PIM. If a new firmware version is required, please refer to the Wyreless Access System Firmware Programming manual for further details. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 11 of 44 3. Panel Interface Module Expander (PIME) The Panel Interface Module Expander (PIME) is a product in the Recognition Sources Wyreless Panel Interface Module (WPIM) category. The PIME installs in a PIM-OTD enclosure and provides the ability to interface 1 to 16 additional Wyreless Access Point Modules (WAPM) to an Access Control Panel. Figure 3-1 shows the PIM-OTD enclosure with PIME-OTD installed. Figure 3-1 PIME-OTD PCB Location in a PIM-OTD Since configuration and operation of a PIME-OTD is identical to a PIM-OTD use Section 2 and replace PIM with PIME where ever found. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 12 of 44 4. Modular Integrated Reader Lock (MIRL) The Modular Integrated Reader Lock (MIRL) is a product in the Recognition Sources Wyreless Access Point Module (WAPM) category. Figure 4-1 MIRL Locked Side (Outside) Figure 4-2 MIRL Unlocked Side (Inside) 4.1 The MIRL Audio/Visual Indicators Action LED Indications 1 MIRL is powered and then displays 2a MIRL Relocks (motor runs) software version number 2b 2c 2d If linking, MIRL sends a link request
(up to 3 times per RF channel) looking for a WPIM in link mode If linking, MIRL & WPIM do an Packet-Error-Rate test for about 20 seconds If linking, MIRL linked successfully and indicates the RF Channel on which it linked 2e Or if linking, MIRL not linked 3 4 5 No communications with card swipe successfully Card swiped and not read Card swiped and read 6 Access denied 7 Access granted, MIRL unlocks 8 MIRL Relocks (motor runs)
(motor runs) X red flashes then Y green flashes*
1 red flash 1 green flash;
then 1 red flash once for each link request sent flashes for each RF transmission:
green flash for a good transmission red flash for a bad transmission Z green flashes*
2 red flashes none none 1 red flash immediate 2 red flashes delayed about 1-15 seconds 1 green flash 1 red flash
* X = major software version number (any number is possible) Y = minor software version number (any number is possible) Z = RF channel number that the MIRL linked on (1-15) MIRL Sounder none 1 beep none none Z beeps*
1 long beep none 1 beep none 1 beep none 1 beep P/N: M053-xxx-x001.1 Table 4-1 MIRL Indicators 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 13 of 44 4.2 Linking the MIRL to a WPIM NOTE: Only one MIRL can be linked at a time. 4.2.1 If the MIRL does not have a Battery Pack installed, install one now (section 4.4). 4.2.2 Make certain that the WPIM to be linked to is in the Link Mode (Section 2.4). 4.2.3 To initiate the linking process:
4.2.3.1 Open the door. 4.2.3.2 Activate and hold down the inside lever to create a Request to Exit Condition. 4.2.3.3 While holding down the lever (Request to Exit), present a card to the card reader. 4.2.3.4 Continue to hold down the lever (Request to Exit) until the MIRL LEDs start to blink indicating that the link process has begun (approximately 8 seconds), then release the lever. 4.2.3.5 Close the door. 4.2.4 During linking, the WPIMs LED (CR6 or CR9, depending on the door (IRL) being linked) and the MIRL LED blink green (some intermittent red may be seen) for about 20 seconds while the MIRL &
WPIM determine the integrity of the selected RF channel. 4.2.5 If the MIRL & WPIM determine that the RF channel can be used, then the linking is completed successfully and the WPIMs LED (CR6 or CR9, whichever was flashing) turns solid green. The MIRL LED then blinks green and the sounder beeps. The number of green blinks and beeps indicates the linked RF channel number. If this occurs go to the next step, section 4.2.6. If the MIRL & WPIM determine that the RF signal quality is not acceptable then the link fails and the MIRL LED blinks red twice and the sounder beeps once (Table 4-1). The WPIM will stay in the Link Mode and the WPIM LED (CR6 or CR9) returns to alternating green and red. If this happens, move either the PIM, or change RF channels and try the link process again (Section 4.2). 4.2.6 The MIRL is now ready to be tested for normal operation. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 14 of 44 Figure 4-3 MIRL Transceiver Cover Figure 4-4 MIRL Battery Pack Removal/Installation Figure 4-5 MIRL Battery Pack P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 15 of 44 4.3 Testing the MIRL 4.3.1 Proximity Card Reader Models 4.3.1.1 Place the card flat to and within one-quarter inch of the upper part of the Proximity Reader
(Figure 4-6). The reader sounder beeps. Figure 4-6 - Presenting a Proximity Card 4.3.1.2 The green LED flashes and the lock will unlock. 4.3.1.3 Turn the Lever and open the door. 4.3.1.4 Shortly after the green flash, there is a red flash and sounder beep signifying relock. 4.3.2 Indication of an Unsuccessful Card Swipe The best indication of an unsuccessful valid card swipe is when the MIRLs internal sounder does not beep, indicating that the card was not read. If an invalid card is swiped, the MIRLs red LED flashes twice and the internal sounder beeps once. In both cases the MIRL remains locked. 4.4 Installing/Replacing the MIRL Battery Pack NOTE: If you want to re-link when changing the MIRL Battery Pack, follow the procedure in section 4.2, page 14. Approximately one month prior the end of the MIRL Elite Battery Pack life, a Low Battery Trouble signal is indicated at the WPIM (Table 2-3) and a Trouble signal will be sent to the access control panel. To install or replace the MIRL Elite Battery Pack, remove the MIRL Transceiver Cover (Figure 4-3). IF replacing, disconnect the old MIRL Battery Pack. If installed, remove the Battery Bracket. If replacing, remove the old Battery Pack (Figure 4-4). Install the new Battery Pack, install the Battery Bracket, and connect the Battery Pack (Figure 4-5). Install the MIRL Transceiver Cover (Figure 4-3). Depending on how long the Battery Pack was disconnected, the MIRL may or may not go through its power-up sequence. In either case the MIRL will stay linked to its WPIM. There is no need to re-link. NOTE: No other WPIM can be in Link Mode during this process. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 16 of 44 4.5 Battery Override If the MIRL Battery Pack fails, a standard 9.0V battery, 522 or equivalent, may be used together with a Battery Override Supply Cable (9VBOC) to power the MIRL so the door can be opened with a valid card. The Battery Override Cable plugs to the Battery Override Connector found on the lower part Card Reader Base Plate after removing the Card Reader Cover (Figure 4-7). NOTE: If the Card Reader Base Plate has a Tamper Switch that is activated when the Reader Cover is removed, then the Card Reader is disabled. Tamper Switch must be manually held closed (simulating the cover being installed) for the Card Reader to operate. Figure 4-7 MIRL Battery Override 4.6 Re-linking an MIRL and WPIM To re-link a MIRL and WPIM, follow the instructions in Section 4.2. 4.7 Changing the RF Channel At the WPIM, change DIP switch SW7 to the desired new RF channel (Section 2.3), place the PIM in Link Mode (see Section 2.4), then re-link the desired MIRL (Section 4.6). NOTE: The WPIMs RF channel DIP switch (SW7) is read when the WPIM enters the Link Mode. If the DIP switch is changed while the WPIM is in the Link Mode, then the WPIM must be taken out of Link Mode and put back into Link Mode for the new RF channel to be selected. The WPIM is taken out of Link Mode by pressing the switch associated with the Access Point that is in the Link Mode (S1 or S2). NOTE: Changing the RF channel will require all WAPMs linked to the PIM to be re-linked. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 17 of 44 5. Wireless Reader Interface (WRI) The Wireless Reader Interface (WRI) is a product in the Recognition Sources Wyreless Access Point Module (WAPM) category. Figure 5-1 Front of the WRI Figure 5-2 Inside the WRI Figure 5-3 WRI Printed Circuit Board (PCB) P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 18 of 44 5.1 The WRI Visual Indicators There are two LEDs on the WRI PCB: a red Power LED (LED1, Figure 5-3) and a green/red State LED
(LED2, Figure 5-3). These LEDs indicate the current status of the WRI (Table 5-1). 1 2 3 4 4a 4b Condition Normal operation, WRI is powered &
the microprocessor is running Tamper On
(WRI door open or external tamper) Tamper Off PIM is not powered or PIM is defective WRI is powered and then displays software version number WRI sends a link request (up to 3 times per RF channel) looking for a WPIM in link mode seconds If linking, WRI & WPIM do an Packet-Error-Rate test for about 20 If linking, WRI linked successfully and indicates the RF Channel on which it linked 4c Or, if linking, WRI not linked successfully LED1
(green) blinking on off on on on on on 5 6 Card swiped and not read Card swiped and read blinking blinking LED Indication LED2
(green red) off off NA X red flashes then Y green flashes*
1 green flash; then 1 red flash once for each link request sent flashes for each RF transmission: green flash for a good transmission, red flash for a bad transmission Z green flashes*
2 red flashes off off 7 No communications with card swipe blinking 1 red flash immediate 8 Access denied blinking 2 red flashes delayed about 1-15 seconds 9 Access granted, WRI activates Strike &
Auxiliary Relays blinking green stays on as long as the Strike Relay is activated
* X = major software version number (any number is possible) Y = minor software version number (any number is possible) Z = RF channel number that the WRI linked on (1-15) Table 5-1 WRI LED Indicators P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 19 of 44 5.2 Linking to the WPIM by Powering or Resetting the WRI NOTE: Only one WRI can be linked at a time. 5.2.1 Make certain that that WPIM to be linked to is in the Link Mode (Section 2.4). 5.2.2 Reset the WRI by either cycling the WRI power (J3, Figure 5-3) or by pressing and releasing the WRI Reset Switch (S1, Figure 5-3). After displaying the firmware version number on LED2, the WRI attempts to link with a WPIM. 5.2.3 During linking, the WPIMs LED (CR6 or CR9, depending on the portal (WRI) being linked) blinks green (some intermittent red may be seen) and the WRI LED2 blinks green (some intermittent red may be seen) for about 20 seconds while the WRI & WPIM determine the integrity of the selected RF channel. 5.2.4 If the WRI & WPIM determine that the RF channel can be used, then the linking is completed successfully and the WPIMs LED (CR6 or CR9, whichever was flashing) turns solid green. LED2 of the WRI then blinks green. The number of green blinks indicates the linked RF channel number. If the WRI & WPIM determine that the RF signal quality is not acceptable then the link fails and the WPR LED2 blinks red twice (Table 5-1). The WPIM will stay in the Link Mode. If this happens, move either the WRI, PIM, or change RF channels and try the link process again (Section 5.2.1). 5.2.5 Close and secure the WRI enclosure cover. 5.2.6 The WRI is now ready to be tested for normal operation. 5.3 Testing the WRI If the WRI was installed with all of its peripherals then there are 8 tests that need to be run before commissioning the WRI for operation. If a WRI peripheral was not installed, then that particular test can be skipped. 5.3.1 Tamper Switch The WRI Tamper Switch (SW1, Figure 5-3) monitors the WRI enclosure door position. If the WRI enclosure door is open a tamper condition is generated. To test the operation of this switch, open the WRI enclosure door, if an External Tamper is wired, make certain the circuit is open or remove the Tamper Input (J2, Figure 5-3) connection, the WRI LED1 should be flashing green. Press SW1 using a finger or non-conductive tool. The WRI LED1 should be a constant green for as long as the switch is pressed. If it was removed, remember to replace the Tamper Input (J2, Figure 5-3) connection. NOTE: The External Tamper Input is wired in parallel with the WRI Tamper Switch (SW1), therefore in order to test the WRI Tamper Switch (SW1), the Tamper Input (J3) must be in the non-Tamper
(pressed) state (i.e. open circuit). 5.3.2 External Tamper Do this test if an external tamper switch is wired to the WRI Tamper Input (J2, Figure 5-3). Open the WRI enclosure door. Press and hold SW1 using a finger or non-conductive tool. When the external tamper switch is closed, the WRI LED1 should be flashing green. When the external tamper switch is open, the WRI LED1 should be a constant green. NOTE: The External Tamper Input is wired in parallel with the WRI Tamper Switch (SW1), therefore in order to test the External Tamper, the WRI Tamper Switch must be in the non-Tamper (pressed) state. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 20 of 44 5.3.3 Request to Exit Do this test if a Request to Exit device is wired to the WRI Portal Inputs (J7-3 & 4, Figure 5-3). Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that activating the Request to Exit device causes a request to exit to be sent to the CDT or ACP software. Also verify that the request to exit is removed when the Request to Exit device goes inactive. 5.3.4 Door Position Do this test if a Door Position device is wired to the WRI Portal Inputs (J7-5 & 6, Figure 5-3). Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that the CDT or ACP software can monitor the doors position by opening and closing the door. 5.3.5 Strike Relay Do this test if an electrical lock or load is connected to the Strike Portal Output (J8-1, 2, and/or 3, Figure 5-3). Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that Strike Portal Output can control the electrical lock or load. 5.3.6 Auxiliary Relay Do this test if an electrical lock or load is connected to the Auxiliary Portal Output (J8-4, 5, and/or 6, Figure 5-3). Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that Auxiliary Portal Output can control the electrical lock or load. 5.3.7 Card Reader 1 Do this test if a card reader or keypad is connected to the Card Reader 1 (J4, Figure 5-3) connector. Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that the card reader or keypad is sending the correct data. 5.3.8 Card Reader 2 Do this test if a card reader or keypad is connected to the Card Reader 2 (J5, Figure 5-3) connector. Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that the card reader or keypad is sending the correct data. 5.4 Re-linking a WRI and WPIM To re-link a WRI and WPIM, follow the instructions in Section 5.2. 5.5 Changing the RF Channel At the WPIM, change DIP switch SW7 to the desired new RF channel (Section 2.3), place the WPIM in Link Mode (see Section 2.4), then re-link the desired WRI (Section 5.2). NOTE: The WPIMs RF channel DIP switch (SW7) is read when the WPIM enters the Link Mode. If the DIP switch is changed while the WPIM is in the Link Mode, then the WPIM must be taken out of Link Mode and put back into Link Mode for the new RF channel to be selected. The WPIM is taken out of Link Mode by pressing the switch associated with the Access Point that is in the Link Mode (S1 or S2). NOTE: Changing the RF channel will require all WAPMs linked to the WPIM to be re-linked. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 21 of 44 6. Wireless Integrated Strike Interface (WISI) The Wireless Integrated Strike Interface (WISI) is a product in the Recognition Sources Wyreless Access Point Module (WAPM) category. Figure 6-1 WISI Components Figure 6-2 WISI Battery Pack Figure 6-3 Control Transceiver with Cover Removed P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 22 of 44 6.1 The WISI Audio/Visual Indicators Action Card Reader LED Indication 1 WISI is powered and then displays 2a WISI Relocks (motor runs) software version number 2b 2c 2d If linking, WISI sends a link request
(up to 3 times per RF channel) looking for a WPIM in link mode If linking, WISI & WPIM do an Packet-Error-Rate test for about 20 seconds If linking, WISI linked successfully and indicates the RF Channel on which it linked 2e Or if linking, WISI not linked 3 4 5 No communications with card swipe successfully Card swiped and not read Card swiped and read X red flashes then Y green flashes*
1 red flash 1 green flash;
then 1 red flash once for each link request sent flashes for each RF transmission:
green flash for a good transmission red flash for a bad transmission Z green flashes*
2 red flashes none none 1 red flash immediate 2 red flashes delayed about 1-15 second 6 Access denied 7 Access granted, WISI unlocks (motor 8 WISI Relocks (motor runs) runs) 1 green flash 1 red flash
* X = major software version number (any number is possible) Y = minor software version number (any number is possible) Z = RF channel number that the WISI linked on (1-15) WISI Sounder none 1 beep none none Z beeps*
1 long beep none 1 beep none 1 beep none 1 beep Table 6-1 WISI Indicators 6.2 Linking to the WPIM by Powering the WISI NOTES:
Only one WISI can be linked at a time. The WISI Battery Pack must be installed before linking (Section 6.4). 6.2.1 Make certain that that WPIM to be linked to is in the Link Mode (Section 2.4). 6.2.2 If the WISI cover is installed, use a Phillips screwdriver to remove WISI cover. There are 4 cover screws, one in each corner (Figure 6-3). 6.2.3 Find, press, and release the WISI Reset Switch located below and to the left side of J4 (Figure 6-3). 6.2.4 During linking, the WPIMs LED (CR6 or CR9, depending on the door (WISI) being linked) blinks green (some intermittent red may be seen) and the WISI Card Reader LED blinks green (some intermittent red may be seen) for about 20 seconds while the WISI & WPIM determine the integrity of the selected RF channel. 6.2.5 If the WISI & WPIM determine that the RF channel can be used, then the linking is completed successfully and the WPIMs LED (CR6 or CR9, whichever was flashing) turns solid green. The WISI Card Reader LED then blinks green and the sounder beeps. The number of green blinks and beeps indicates the linked RF channel number. If the WISI & WPIM determine that the RF signal quality is not acceptable then the link fails and the WISI LED blinks red twice and the sounder beeps once (Table 6-1). The WPIM will stay in the Link P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 23 of 44 Mode. If this happens, move either the WISI, PIM, or change RF channels and try the link process again (Section 6.2.1). 6.2.6 Re-install the WISI cover, making certain that no wires are pinched. The cover should go on easy with no interferences. Replace the 4 cover screws, one in each corner (Figure 6-1). 6.2.7 The WISI is now ready to be tested for normal operation. 6.3 Testing the WISI NOTE: The WISI Card Reader will not work as long as the WISI Enclosure Cover is removed (i.e. the WISI Card Reader will not work if there is a WISI Tamper). 6.3.1 Magnetic Stripe or Wiegand Card Reader Models 6.3.1.1 Insert the card and slide it down the slot keeping its back edge against the back of the readers slot throughout the entire swipe. The reader sounder beeps. 6.3.1.2 The WISI Card Reader LED flashes green and the strike unlocks. 6.3.1.3 Shortly after the green flash, there is a red flash and sounder beep signifying relock. 6.3.2 Proximity Card Reader Models 6.3.2.1 Place the card flat to and within one-quarter inch of the upper part of the Proximity Reader. The reader sounder beeps. 6.3.2.2 The WISI Card Reader LED flashes green and the strike unlocks. 6.3.2.3 Shortly after the green flash, there is a red flash and sounder beep signifying relock. 6.3.3 Indication of an Unsuccessful Card Swipe The best indication of an unsuccessful valid card swipe is when the WISIs internal sounder does not beep, indicating that the card was not read. If an invalid card is swiped, the WISI Card Reader LED flashes red twice and the internal sounder beeps once. In both cases the WISIs strike remains locked. 6.4 Replacing the WISI Battery Pack, BP12V-001 Approximately one month prior the end of the WISIs Battery Pack life, a Low Battery Trouble signal is indicated at the WPIM (Table 6-1), a Trouble signal will be sent to the access control panel. NOTE: Make certain no WPIMs are in the Link Mode when replacing the WISI Battery Pack or the WISI may inadvertently link to the wrong WPIM. 6.4.1 Use a Phillips screwdriver to remove WISI cover. There are 4 cover screws, one in each corner
(Figure 6-3). 6.4.2 Locate the used Battery Pack (Figure 6-4), disconnect the used Battery Pack, and remove the used Battery Pack from its Velcro Strips. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 24 of 44 Figure 6-4 Removing the Used Battery Pack 6.4.3 Install the Battery Pack into the Transceiver Control Module enclosure using the Velcro provided AND connect the Battery Pack Connector to its mating connector that is factory connected to J4
(Figure 6-5). Figure 6-5 New Battery Pack Installed 6.4.4 To continue to use the WISI on the same RF channel and with the same WPIM, make certain that no WPIMs are in the Link Mode, then press and release the WISI Reset Switch located below and to the left side of J4 (Figure 6-5). This insures that the WISI has started properly. Re-install the WISI cover, making certain that no wires are pinched. The cover should go on easy with no interferences. Replace the 4 cover screws, one in each corner (Figure 6-1). If the WPR needs to be re-linked or the RF channel needs to be changed, before re-installing the WISI cover, follow the instructions in Section 6.2 or Section 6.7. NOTE: No other WPIM can be in Link Mode during this process. 6.5 Battery Override If the WISI Battery Pack fails, a standard 9.0V battery, 522 or equivalent, may be used together with a Battery Override Supply Cable (9VBOC) to power the WISI so the door can be opened with a valid card. The Battery Override Cable plugs to the Battery Override Connector found on the underside of the card reader. 6.6 Re-linking an WISI and WPIM To re-link a WISI and WPIM follow the instructions in Section 6.2. 6.7 Changing the RF Channel At the WPIM, change DIP switch SW7 to the desired new RF channel (Section 2.3), place the PIM in Link Mode (see Section 2.4), then re-link the desired WISI (Section 6.6). NOTE: The WPIMs RF channel DIP switch (SW7) is read when the WPIM enters the Link Mode. If the DIP switch is changed while the WPIM is in the Link Mode, then the WPIM must be taken out of Link Mode and put back into Link Mode for the new RF channel to be selected. The WPIM P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 25 of 44 is taken out of Link Mode by pressing the switch associated with the Access Point that is in the Link Mode (S1 or S2). NOTE: Changing the RF channel will require all WAPMs linked to the PIM to be re-linked. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 26 of 44 7. Wireless Universal Strike Interface (WUSI) The Wireless Universal Strike Interface (WUSI) is a product in the Recognition Sources Wyreless Access Point Module (WAPM) category. Figure 7-1 Front of the WUSI Figure 7-2 Inside the WUSI Figure 7-3 WUSI Printed Circuit Board (PCB) P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 27 of 44 7.1 The WUSI Visual Indicators Depending on how the Card Reader is interfaced to the WUSI, the LED on the Card Reader may display some WUSI status conditions (Table 7-1). 1 2 3a 3b Condition WUSI is powered and then displays software version number Card Reader LED Y green flashes*
WUSI sends a link request (up to 3 times per RF channel) looking for a WPIM in If linking, WUSI & WPIM do an Packet-Error-Rate test for about 20 link mode seconds If linking, WUSI linked successfully and indicates the RF Channel on which it linked 3c Or, if linking, WUSI not linked successfully 4 5 Card swiped and not read Card swiped and read 1 green flash each link request sent flashes for each RF transmission: green flash for a good transmission, red flash for a bad transmission Z green flashes*
2 red flashes solid red red to green to red 6 No communications with card swipe red to green to red 7 Access denied 8 Access granted, WUSI activates Strike &
Auxiliary Relays red to green to red green stays on as long as the Strike Relay is activated
* Y = minor software version number (any number is possible) Z = RF channel number that the WUSI linked on (1-15) Table 7-1 WUSI LED Indicators 7.2 Linking to the WPIM by Powering the WUSI NOTE: Only one WUSI can be linked at a time. 7.2.1 Make certain that that WPIM to be linked to is in the Link Mode (Section 2.4). 7.2.2 Reset the WUSI by cycling the WUSI power (Figure 7-3). The WUSI attempts to link with a WPIM. 7.2.3 During linking, the WPIMs LED (CR6 or CR9, depending on the portal (WUSI) being linked) blinks green (some intermittent red may be seen) and the WUSI Card Reader LED may blink green (some intermittent red may be seen) for about 20 seconds while the WUSI & WPIM determine the integrity of the selected RF channel. 7.2.4 If the WUSI & WPIM determine that the RF channel can be used, then the linking is completed successfully and the WPIMs LED (CR6 or CR9, whichever was flashing) turns solid green. The WUSI Card Reader LED may then blink green. The number of green blinks indicates the linked RF channel number. If the WUSI & WPIM determine that the RF signal quality is not acceptable then the link fails and the WUSI Card Reader LED may blink red twice (Table 7-1). The WPIM will stay in the Link Mode. If P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 28 of 44 this happens, move either the WUSI, PIM, or change RF channels and try the link process again
(Section 7.2.1). 7.2.5 Close and secure the WUSI enclosure cover. 7.2.6 The WUSI is now ready to be tested for normal operation. 7.3 Testing the WUSI If the WUSI was installed with all of its peripherals then there are 6 tests that need to be run before commissioning the WUSI for operation. If a WUSI peripheral was not installed, then that particular test can be skipped. 7.3.1 Tamper Switch The WUSI Tamper Switch (Figure 7-3) monitors the WUSI enclosure cover position. If the WUSI enclosure cover is open a tamper condition is generated. To test the operation of this switch, make certain that the WUSI is linked to a PIM, open the WUSI enclosure cover, if an External Tamper is wired, make certain the circuit is open or remove the Tamper Input (J2, Figure 7-3) connection, the PIMs Trouble LED (CR7 or CR10) should be flashing 3 red blinks. Install the WUSI cover. The PIMs Trouble LED (CR7 or CR10) should not be flashing 3 red blinks for as long as the WUSIs cover in installed. Note: The Trouble LED may be flashing other trouble codes, just make certain it is not flashing the Tamper error code: 3 red blinks. If it was removed, remember to replace the Tamper Input (Figure 7-3) connection. NOTE: The External Tamper Input is wired in parallel with the WUSI Tamper Switch (SW1), therefore in order to test the WUSI Tamper Switch, the Tamper Input must be in the non-Tamper
(pressed) state (i.e. open circuit). 7.3.2 External Tamper Do this test if an external tamper switch is wired to the WUSI Tamper Input (Figure 7-3). Make certain that the WUSI is linked to a PIM. Install the WUSI enclosure cover. When the external tamper switch is closed, the PIMs Trouble LED (CR7 or CR10) should be flashing 3 red blinks. When the external tamper switch is open, the PIMs Trouble LED (CR7 or CR10) should not be flashing 3 red blinks for as long as the switch is pressed. Note: The Trouble LED may be flashing other trouble codes, just make certain it is not flashing the Tamper error code: 3 red blinks. NOTE: The External Tamper Input is wired in parallel with the WUSI Tamper Switch, therefore in order to test the External Tamper, the WUSI Tamper Switch must be in the non-Tamper (pressed) state. 7.3.3 Request to Exit Do this test if a Request to Exit device is wired to the WUSI Portal Inputs (Figure 7-3). Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that the activating the Request to Exit device causes a request to exit to be sent to the CDT or ACP software. Also verify that the request to exit is removed when the Request to Exit device goes inactive. 7.3.4 Door Position Do this test if a Door Position device is wired to the WUSI Portal Inputs (Figure 7-3). Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that the CDT or ACP software can monitor the doors position by opening and closing the door. 7.3.5 Strike Relay Do this test if an electrical lock or load is connected to the Strike Portal Output (Figure 7-3). Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 29 of 44 Panels software (ACP Software), verify that Strike Portal Output can control the electrical lock or load. 7.3.6 Card Reader Do this test if a card reader or keypad is connected to the Card Reader (Figure 7-3) connector. Using either the Recognition Sources Configuration and Demonstration Tool (CDT) or the Access Control Panels software (ACP Software), verify that the card reader or keypad is sending the correct data. 7.4 Re-linking a WUSI and WPIM To re-link a WUSI and WPIM, follow the instructions in Section 7.2. 7.5 Changing the RF Channel At the WPIM, change DIP switch SW7 to the desired new RF channel (Section 2.3), place the WPIM in Link Mode (see Section 2.4), then re-link the desired WUSI (Section 7.2). NOTE: The WPIMs RF channel DIP switch (SW7) is read when the WPIM enters the Link Mode. If the DIP switch is changed while the WPIM is in the Link Mode, then the WPIM must be taken out of Link Mode and put back into Link Mode for the new RF channel to be selected. The WPIM is taken out of Link Mode by pressing the switch associated with the Access Point that is in the Link Mode (S1 or S2). NOTE: Changing the RF channel will require all WAPMs linked to the WPIM to be re-linked. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 30 of 44 8. Wireless Portable Reader (WPR) The Wireless Portable Reader (WPR) is a product in the Recognition Sources Wyreless Access Point Module (WAPM) category. Figure 8-1 Wireless Portable Reader (WPR) with Proximity Reader P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 31 of 44 8.1 The WPR Audio/Visual Indicators Action LED Indication 2a 1 WPR is powered and then displays software version number If linking, WPR sends a link request
(up to 3 times per RF channel) looking for a WPIM in link mode If linking, WPR & WPIM do an Packet-Error-Rate test for about 20 seconds If linking, WPR linked successfully and indicates the RF Channel on which it linked 2b 2c 2d Or if linking, WPR not linked successfully 3 Card swiped and not read 4 Card swiped and read 5 No communications 6 Invalid card swiped 7 Valid card swiped Low WPR Battery 8 X red flashes then Y green flashes*
1 green flash;
then 1 red flash once for each link request sent flashes for each RF transmission:
green flash for a good transmission red flash for a bad transmission Z green flashes*
2 red flashes none none 1 red flash immediate 1 long red flash delayed about 1-15 seconds W seconds long green flash*
1 long red flash
* X = major software version number (any number is possible) Y = minor software version number (any number is possible) Z = RF channel number that the WPR linked on (1-15) W = green LED stays on for the door unlock time WPR Sounder none none none Z beeps*
1 long beep none 1 beep none 1 beep none 3 beeps 8.2 Turning the WPR On Table 8-1 WPR Indicators The WPR is turned On & Off using the On/Off switch located on the WPR cover (Figure 8-1). When the WPR is turned on, Action 1, Table 8-1 occurs. Actions 2a, 2b, 2c, and/or 2d will only occur if the WPR is being linked (Section 8.3). 8.3 Linking or Re-Linking to the WPIM by Powering the WPR NOTE: Only one WAPM can be linked at a time. 8.3.1 Make certain that that WPIM to be linked to is in the Link Mode (Section 2.4). 8.3.2 Make certain that the WPR is turned off using the On/Off switch (Figure 8-1). 8.3.3 With the WPR turned off, swipe or present a card at the WPR card reader (Figure 8-1) (Section 10.4). 8.3.4 Use the Phillips screwdriver to remove WPR cover. There are 4 cover screws, one in each corner
(Figure 8-1). P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 32 of 44 8.3.5 Locate the Door Position Switch Connector on the WPR PCB (Figure 8-2, DPS1). Temporarily short the two terminals of the Door Position Switch Connector. While keeping these two terminals shorted, turn on the WPR using the On/Off switch (Figure 8-1). Keep the two terminals shorted until the WPR enters the Linking Mode (Table 8-1, actions 2a or 2b). Once the WPR is in the Linking Mode, remove the short. Figure 8-2 WPR PCB Connectors 8.3.6 During linking, the WPIMs LED (CR6 or CR9, depending on the WPR being linked) blinks green
(some intermittent red may be seen) and the WPR LED (Figure 8-1) blinks green (some intermittent red may be seen) for about 20 seconds while the WPR & WPIM determine the integrity of the selected RF channel. 8.3.7 If the WPR & WPIM determine that the RF channel can be used, then the linking is completed successfully and the WPIMs LED (CR6 or CR9, whichever was flashing) turns solid green. The WPR LED blinks green and the sounder beeps, the number of which indicate the RF channel linked. If the WPR & WPIM determine that the RF signal quality is not acceptable then the link fails and the WPR LED blinks red twice and the sounder beeps once (Table 8-1). The WPIM will stay in the Link Mode. If this happens, move either the WPR, PIM, or change RF channels and try the link process again (Section 8.3.1). 8.3.8 Re-install the WPR cover, making certain that no wires are pinched. The cover should go on easy with no interferences. Replace the 4 cover screws, one in each corner (Figure 8-1). 8.3.9 The WPR is now ready to be tested for normal operation. 8.4 Testing the WPR 8.4.1 Magnetic Stripe or Wiegand Card Reader Models 8.4.1.1 Insert a valid card and slide it down the slot keeping its back edge against the back of the readers slot throughout the entire swipe. The reader sounder beeps. 8.4.1.2 The green LED will flash. 8.4.2 Proximity Card Reader Models 8.4.2.1 Place a valid card flat to and within one-quarter inch of the upper part of the Proximity Reader. The reader sounder beeps. 8.4.2.2 The green LED will flash. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 33 of 44 8.4.3 Indication of an Unsuccessful Card Swipe The best indication of an unsuccessful valid card swipe is when the WPRs internal sounder does not beep, indicating that the card was not read correctly. If an invalid card is swiped, the WPRs red LED displays a long flash and the internal sounder beeps once. 8.5 Replacing the WPR Battery Pack, BP12V-001 Approximately one month prior the end of the WPRs Battery Pack life, a Low Battery Trouble signal is indicated at the WPIM (Table 2-3), a Trouble signal will be sent to the access control panel, and the WPR will provide a visual and audible indication (Table 8-1, action 7) consisting of a long red LED flash and three sounder beeps. The WPRs low battery indication (Table 8-1, action 7) will occur whenever the WPRs battery is low and:
the WPR is turned on (after action 1, Table 8-1), the WPR transmits a Heartbeat, or any card is swiped at the WPRs reader. It is then time to replace the WPRs Battery Pack:
8.5.1 Use the Phillips screwdriver to remove WPR cover. There are 4 cover screws, one in each corner
(Figure 8-1). 8.5.2 Locate the used Battery Pack (Figure 8-6), disconnect the used Battery Pack (Figure 8-4), remove the used Battery Pack from its Velcro Strips (Figure 8-3) 8.5.3 Attach a new Battery Pack to the housing using the Velcro strips (Figure 8-3& Figure 8-4). Figure 8-3 WPR Battery Pack Velcro Strips Figure 8-4 WPR Battery Pack Positioned P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 34 of 44 8.5.4 Connect the battery connector to the mating connector coming from the transceiver board (Figure 8-5
& Figure 8-6). Figure 8-5 WPR Battery Connector 8.5.5 To continue to use the WPR on the same RF channel and with the same WPIM, re-install the cover, Figure 8-6 WPR Battery Pack Connected making certain that no wires are pinched. The cover should go on easy with no interferences. Replace the 4 cover screws, one in each corner (Figure 8-1). If the WPR needs to be re-linked or the RF channel needs to be changed, before re-installing the WPR cover, follow the instructions in Section 8.2 or Section 8.6. 8.6 Changing the RF Channel At the WPIM, change DIP switch SW7 to the desired new RF channel (Section 2.3), place the WPIM in Link Mode (see Section 2.4), then re-link the desired WPR (Section 8.2). NOTE: The WPIMs RF channel DIP switch (SW7) is read when the WPIM enters the Link Mode. If the DIP switch is changed while the WPIM is in the Link Mode, then the WPIM must be taken out of Link Mode and put back into Link Mode for the new RF channel to be selected. The WPIM is taken out of Link Mode by pressing the switch associated with the Access Point in the Link Mode
(S1 or S2). NOTE: Changing the RF channel will require all WAPMs linked to the PIM to be re-linked. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 35 of 44 9. Wireless Contact Monitor (WCM) The Wireless Contact Monitor (WCM) is a product in the Recognition Sources Wyreless Access Point Module (WAPM) category. Figure 9-1 Wireless Contact Monitor Figure 9-2 WCM Battery Pack Figure 9-3 Transceiver Control Module with Cover Removed P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 36 of 44 9.1 The WCM Visual Indicators NOTE: LED assembly XXX-XXX-XXX must be installed on the GRN_LED & RED_LED connections of J3 in order for any visual indicators to be seen. Action 1 WCM is powered and then displays 2a WCM is ready to start linking software version number 2b 2c 2d If linking, WCM sends a link request
(up to 3 times per RF channel) looking for a WPIM in link mode If linking, WCM & WPIM do an Packet-Error-Rate test for about 20 seconds If linking, WCM linked successfully and indicates the RF Channel on which it linked 2e Or if linking, WCM not linked successfully LED Assembly on J3 X red flashes then Y green flashes*
1 red flash 1 green flash;
then 1 red flash once for each link request sent flashes for each RF transmission:
green flash for a good transmission red flash for a bad transmission Z green flashes*
2 red flashes
* X = major software version number (any number is possible) Y = minor software version number (any number is possible) Z = RF channel number that the WCM linked on (1-15) 9.2 Linking to the WPIM by Resetting the WCM Table 9-1 WCM Visual Indicators NOTES:
Only one WCM can be linked at a time. The WCM Battery Pack must be installed before linking (Section 9.3). Leaving the WCM cover off for extended periods of time with the Battery Pack connected will shorten the expected battery life. 9.2.1 Make certain that that WPIM to be linked to is in the Link Mode (Section 2.4). 9.2.2 If the WCM cover is installed, use a Phillips screwdriver to remove WCM cover. There are 4 cover screws, one in each corner (Figure 9-3). 9.2.3 Find, press, and release the WCM Reset Switch located below and to the left side of J4 (Figure 9-3). 9.2.4 During linking, the WPIMs LED (CR6 or CR9, depending on the WAPM being linked) blinks green
(some intermittent red may be seen) and the LED Assembly blinks green (some intermittent red may be seen) for about 20 seconds while the WCM & WPIM determine the integrity of the selected RF channel. 9.2.5 If the WCM & WPIM determine that the RF channel can be used, then the linking is completed successfully and the WPIMs LED (CR6 or CR9, whichever was flashing) turns solid green. The LED Assembly then blinks green. The number of green blinks indicates the linked RF channel number. If the WCM & WPIM determine that the RF signal quality is not acceptable then the link fails and the LED blinks red twice (Table 9-1). The WPIM will stay in the Link Mode. If this happens, move either the WCM, PIM, or change RF channels and try the link process again (Section 9.2). P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 37 of 44 9.2.6 Re-install the WCM cover, making certain that no wires are pinched. The cover should go on easy with no interferences. Replace the 4 cover screws, one in each corner (Figure 9-1). 9.2.7 The WCM is now ready for normal operation. 9.3 Replacing the WCM Battery Pack, BP12V-001 Approximately one month prior the end of the WCMs Battery Pack life, a Low Battery Trouble signal is indicated at the WPIM (Table 2-3), a Trouble signal will be sent to the access control panel. NOTE: Make certain no WPIMs are in the Link Mode when replacing the WCM Battery Pack or the WCM may inadvertently link to the wrong WPIM. NOTE: Leaving the WCM cover off for extended periods of time with the Battery Pack connected will shorten the expected battery life. 9.3.1 Use a Phillips screwdriver to remove WCM cover. There are 4 cover screws, one in each corner
(Figure 9-1). 9.3.2 Locate the used Battery Pack (Figure 9-4), disconnect the used Battery Pack, and remove the used Battery Pack from its Velcro Strips. Figure 9-4 Removing the Used Battery Pack 9.3.3 Install the Battery Pack into the Transceiver Control Module enclosure using the Velcro provided AND connect the Battery Pack Connector to its mating connector that is factory connected to J4
(Figure 9-5). Figure 9-5 New Battery Pack Installed P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 38 of 44 9.3.4 To continue to use the WCM on the same RF channel and with the same WPIM, make certain that no WPIMs are in the Link Mode, then press and release the WCM Reset Switch located below and to the left side of J4 (Figure 9-5). This insures that the WCM has started properly. Re-install the WCM cover, making certain that no wires are pinched. The cover should go on easy with no interferences. Replace the 4 cover screws, one in each corner (Figure 9-1). If the WPR needs to be re-linked or the RF channel needs to be changed, before re-installing the WCM cover, follow the instructions in Section 9.1 or Section 9.4. NOTE: No other WPIM can be in Link Mode during this process. 9.4 Re-linking an WCM and WPIM To re-link a WCM and WPIM follow the instructions in Section 9.1. 9.5 Changing the RF Channel At the WPIM, change DIP switch SW7 to the desired new RF channel (Section 2.3), place the PIM in Link Mode (see Section 2.4), then re-link the desired WCM (Section 9.4). NOTE: The WPIMs RF channel DIP switch (SW7) is read when the WPIM enters the Link Mode. If the DIP switch is changed while the WPIM is in the Link Mode, then the WPIM must be taken out of Link Mode and put back into Link Mode for the new RF channel to be selected. The WPIM is taken out of Link Mode by pressing the switch associated with the Access Point that is in the Link Mode (S1 or S2). NOTE: Changing the RF channel will require all WAPMs linked to the PIM to be re-linked. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 39 of 44 10. Other Important Information 10.1 Knowing When to Change the RF Channel The RF Channel should be changed if the system encounters interfering transmissions (most noticeably when the system attempts to Link and cannot or when a card swipe results in a no communication indication at the Access Point). Try re-linking on a different RF channel. If the WAPM and WPIM do not re-link on the new channel, try another channel. For more detailed information, see Wyreless Access Troubleshooting Guide, available from Recognition Source. If the WAPM and WPIM do not re-link, the WAPM reverts to the RF channel it was set at prior to disconnecting the WAPM power. However, the WAPM will not communicate with the WPIM on the original RF channel until the WPIMs DIP switch SW7 is reset to the original RF channel and the WPIM is taken into and out of Link Mode. 10.2 Configuring the Wyreless AccessTM System There are several configurable features in each WAPM & WPIM. These are programmed through the WPIM using a PC and the Recognition Source Configuration & Demonstration Tool. The configurable features are:
Heartbeat time (default: 10 minutes) Relock time (default: 3 seconds) Re-latch on: timer, door opening, or door closing (default: timer) Card conversion (default: none) Polarity of the Request-to-Exit (RTE) signal (default: low = RTE) Polarity of Trouble signal (default: low = trouble) Polarity of Door Position Switch (DPS) signal (default: low = closed) Extended Unlock: enabled or disabled (default: enabled) 10.3 Extended Unlock Extended unlock is a feature that permits a Wyreless Access Point Module (WAPM) to stay in an indefinite unlock state. Normally a card is swiped at a WAPM and if it is a valid card, the Access Point will unlock for a short period of time (seconds) and then automatically relock. This is considered a momentary unlock. A WPIM and WAPM can be configured (section 10.2) to respond to extended unlocks from an access control panel. The WPIM monitors the state of the access control panels strike relay. When the strike relay is energized without the WPIM presenting card data (i.e. no card swipe has occurred) to the access control panel, then the next time the WAPM communicates with the WPIM (card swipe, door state change, request to exit, or heartbeat), the WPIM will tell the WAPM to unlock its portal (door, gate, etc.) indefinitely. When the WPIM detects that the strike relay is de-energized, then the next time the WAPM communicates with the WPIM (card swipe, door state change, request to exit, or heartbeat), the WPIM will tell the WAPM to lock its portal (door, gate, etc.) indefinitely. The extended unlock feature is most likely to be used to implement a timed unlock. For instance, wanting a business main entry doors unlocked during normal business hours (i.e. 8-5). P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 40 of 44 Note: The exact time that the Access Point will be unlocked or locked depends on the frequency of RF activity between the WAPM and the WPIM. Generally the WAPM is in a low power mode (i.e. sleeping) and therefore the WPIM can only communicate with the WAPM when the WAPM initiates the communication. The Heartbeat time will determine the maximum time that it will take for a WAPM to respond to the start or end of an extended unlock. For instance, lets say that the Heartbeat time is set to 10 minutes and that we want the Access Point to be unlocked from 8-5. We would program the access control panel to unlock the Access Point at 7:50 and lock it at 5:00. The WAPM would unlock sometime between 7:50 & 8:00 and would lock sometime between 5:00 & 5:10. 10.4 Why Swipe a Card When the Power Is Disconnected?
When linking or re-linking, the instructions say to swipe a card after the power has been removed from the WAPM that will be linked or linked, why?
Most of the time a WAPM is in a very lower power mode to conserve energy and extend battery life. Therefore when power is removed, if a WAPM is in its low power mode, it will stay powered for several minutes due to capacitance in the DC regulator on the PCB. Swiping a card will cause the WAPM to go to a high power mode which will collapse any residual power. This will insure that the WAPM will start from reset when power is reapplied. If a card is not swiped and power is reapplied, no damage is done, but if power has only been removed for a short time, the WAPM (specifically the WPR) will not reset. The WAPM will just continue to operate as if power had never been removed. If the WAPM does not reset when power is reapplied, then the WAPM link mode will not be entered, which may have been the primary reason for cycling power. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 41 of 44 For questions regarding Wyreless Access:
11. Contacting Recognition Source
(630) 762-4450
(630) 762-4444 fax P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 42 of 44 12. FCC Compliance & Warnings 12.1 FCC Compliance This device has been authorized by the FCC Rules and Industry Canada. This device complies with the limits for a Class B digital device and a Class B intentional radiator, pursuant to Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Wyreless Access System Component must be installed by qualified professionals or contractors in accordance with FCC part 15.203, Antenna Requirements. Do not use any antenna other than the one provided with the unit. 12.2 Warnings RF Exposure - To comply with FCC RF exposure requirements for mobile transmitting devices this transmitter should only be used or installed at locations where there is normally at least a 20 cm separation between the antenna and all persons. Do not co-locate and operate in conjunction with any other antenna or transmitter. Use only the Battery Pack specified in this instruction manual. Do not subject Battery Pack to fire or high temperatures. Do not attempt to recharge, short out or disassemble Battery Pack. Follow local regulations for alkaline battery disposal. Immediately remove the batteries and discontinue use if:
- the product is impacted after which the interior is exposed, or
- the product emits a strange smell, heat, or smoke. Changes or modifications not expressly approved by Recognition Source could void the users authority to operate the equipment. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 43 of 44 13. Revision History Version x001 x001.1 Date 09/09/03 12/08/03 Changes preliminary in house release for comments deleted PIM & PIM-OTD sales models, deleted IRL section, added WRI, WISI, WUSI, WPR, & WCM sections P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 44 of 44
1 2 3 | Users manual | Users Manual | 1.89 MiB | November 09 2003 |
PPPRRREEELLLIIIMMMIIINNNAAARRRYYY INSTALLATION INSTRUCTIONS MODULAR INTEGRATED READER LOCK
(MIRL) STANDARD CYLINDRICAL 3820 Stern Avenue St. Charles, IL 60174 Phone: 630-762-4450 Fax: 630-762-4455 P/N: M053-xxx-x001 3820 Stern Avenue St Charles, IL 60174
(630) 762-4450
(630) 762-4455 Fax Copyright 2003 Recognition Source, LLC, all rights reserved. No part of this document can be reproduced, transmitted, or transcribed in any form by electrical, mechanical, optical, manual, or otherwise without the prior written consent of Recognition Source. Recognition Source reserves the right to alter or revise the content of this document as needed to support future product revisions, without obligation to notify any persons of specific changes. The use of trademarks, trade names, or other product identification is solely for reference purposes. All other product brand names are trademarks or registered trademarks of their respective holders. Recognition Source believes the information in this document to be accurate and reliable. Recognition Source does not guarantee results from the use of this information. Recognition Source assumes no responsibility, obligation, or liability for the information presented in this document. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 2 of 37 INSTALLATION INSTRUCTIONS Wyreless Access MIRL Standard Cylindrical NOTE: These instructions are for installing the Modular Integrated Reader Lock (MIRL) Standard Cylindrical, a component of a Wyreless Access System. After completing this installation refer to the Configuring and Operating the Wyreless Access System manual. Table of Contents 2. 1. Wyreless AccessTM System Components...............................................................................................................4 1.1 Overview............................................................................................................................................................4 1.2 MIRL Standard Cylindrical Components & Sales Models ............................................................................5 Installing the MIRL Standard Cylindrical ...........................................................................................................7 2.1 Tools Required..................................................................................................................................................7 2.2 Determining the Best WPIM and MIRL Locations........................................................................................7 2.3 Door Preparation...............................................................................................................................................7 2.4 Marking Holes for Drilling...............................................................................................................................7 2.5 Drilling Holes................................................................................................................................................. 12 2.6 Marking & Drilling Transceiver Mounting Holes ....................................................................................... 12 2.7 Marking & Drilling Reader Mounting Holes............................................................................................... 14 2.8 Mortising for Latch........................................................................................................................................ 16 2.9 Installing the Optional Door Position Switch............................................................................................... 17 2.10 Mounting Transceiver.................................................................................................................................... 18 2.11 Connecting Door Position Switch Wires...................................................................................................... 21 2.12 Mounting Reader............................................................................................................................................ 22 2.13 Adjusting Lockset to Door Thickness........................................................................................................... 25 2.14 Placing the Lock Chassis into the Chassis Hole and Then Engaging the Retractor in Latch................... 27 2.15 Connecting & Dressing the Motor, Request to Exit, & Ground Wires ...................................................... 28 Installing the Inside Rose Assembly & Cover ............................................................................................. 28 2.16 Installing the Inside Lever............................................................................................................................. 30 2.17 Installing Strike Plate..................................................................................................................................... 30 2.18 2.19 Installing the Optional Door Position Magnet.............................................................................................. 31 Install the Battery Pack & Transceiver Cover.............................................................................................. 32 2.20 3. Troubleshooting...................................................................................................................................................... 34 4. Contacting Recognition Source............................................................................................................................ 35 5. FCC/UL Compliance & Warnings...................................................................................................................... 36 FCC Compliance............................................................................................................................................ 36 5.1 5.2 UL Compliance.............................................................................................................................................. 36 5.3 Warnings......................................................................................................................................................... 36 6. Revision History..................................................................................................................................................... 37 P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 3 of 37 1. Wyreless AccessTM System Components 1.1 Overview Every access control system that uses Wyreless AccessTM contains two different types of modules (Figure 1-1):
at least one Wyreless Panel Interface Module (WPIM), and at least one Wyreless Access Point Module (WAPM) Access Control Panel Wired Communication Wyreless Panel Interface Module
(WPIM) RF Communication Wyreless Access Point Module
(WAPM) Wired Communication Access Point Access Control Panel Location Access Point Location Figure 1-1 Wyreless Access System Block Diagram Recognition Sources product line contains several different expressions of each module. The WPIM is wired to the access control panel and ideally is installed very close to the access control panel. The WPIMs installation location is determined by the location of the WAPMs with which it will communicate using RF. The WAPM is installed at the access point where access will be controlled and/or monitored. Depending on the application and which WAPM is used, some wiring at the access control point may be required. Regardless of which WPIM or WAPM module is used, the communication link between the WPIM and WAPM is always RF. This manual describes the installation of a Modular Integrated Reader Lock (MIRL) Standard Cylindrical which is a WAPM. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 4 of 37 1.2 MIRL Standard Cylindrical Components & Sales Models The MIRL Standard Cylindrical includes 7 components (Figure 1-2, Figure 1-3, Figure 1-4, and Figure 1-5 ):
electrical lock card reader power supply door position switch connections request-to-exit sensor RF receiver RF transmitter Figure 1-2 Unlocked Side of the MIRL Figure 1-3 Locked Side of the MIRL Figure 1-4 MIRL Battery Pack Figure 1-5 Exploded MIRL P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 5 of 37 Table 1-1- MIRL Standard Cylindrical Sales Model Table NOTE: Reader types are UL Recognized Components:
(PH) = Recognition Source, Model MIRL-PH-UR
(PI) = Recognition Source, Model MIRL-PI-UR
(MG) = Recognition Source, Model MIRL-MG-UR
(Refer to Installation Instructions P/N M053-028-xxx.) When the outside portion (reader side) of the MIRL is actually outdoors, make certain that the inside portion
(transceiver side) of the MIRL is in a temperature controlled environment where a minimum temperature of 32? F (0? C) is maintained with 72? F (22? C) being optimum. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 6 of 37 2. Installing the MIRL Standard Cylindrical 2.1 Tools Required 2 1/8 Boring Bit, if needed, 5/16, 3/8, 7/16, 3/4", 1 Drill Bits, Templates RSTP21 (T147-008-001) provided (also available at www.recognition-source.com), Center punch, Drill with chuck for 1 bits, Flat and Phillips head screwdrivers, T-10 & T15 TORX tamper resistant L-keys, provided, Chisels, if Strike has to be mortised, Square, Level, Pencil, Masking Tape. 2.2 Determining the Best WPIM and MIRL Locations Proper selection of the WPIM and the MIRL mounting locations insures reliable RF communications. The mounting location of the MIRL is fixed by the location of the door. Best RF performance is achieved when the MIRL Antenna Cover (Figure 1-2) can never be within 4 of any metal object whether the door is closed or open. This does not include any metal that maybe in the door or door frame. The MIRL Antenna Cover is located just above the Cylindrical Lockset on the unlocked side of the door
(Figure 1-2). Since mounting location of the MIRL is fixed by the location of the door, only the location of the WPIM can be varied to achieve optimum RF performance. The WPIM manual contains a section for determining the best location for the WPIM. The maximum distance between WPIM and an MIRL is 200 horizontally when installed inside a building that uses normal building construction materials. The maximum distance is 600 for a line of sight installation. NOTE: When the outside portion (reader side) of the MIRL is actually outdoors, make certain that the inside portion (transceiver side) of the MIRL is in a temperature controlled environment where a minimum temperature of 32? F (0? C) is maintained with 72? F (22? C) being optimum. 2.3 Door Preparation If the door already has a lockset installed, remove it. 2.4 Marking Holes for Drilling NOTE: Some doors may have some holes already drilled; skip the instructions related to those holes. The suggested height from the floor to the centerline of the Lever is 38. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 7 of 37 2.4.1 Door Side 2.4.1.1 Mark a horizontal line 38 from the floor between 2 to 3 from the edge of the door on both sides of the door. Use a level. 2.4.1.2 Using a square (to compensate for beveled door edges), mark a point along the horizontal line 2 from the door edge on both sides of the door (Figure 2-1). Figure 2-1 Marking 2 Setback with Square P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 8 of 37 2.4.1.3 NOTE: There is a template for a metal door (hollow core) and a different template for a wood door (solid core). Make certain you are using the correct template!
If the door does not have the 2 1/8 hole already drilled, place the Template, RSTP21, so that the center of Hole #3 (the 2 1/8 hole) is centered over the intersection of the horizontal line drawn in Section 2.4.1.1 and the 2 setback line drawn in Section 2.4.1.2. If the 2 1/8 hole already exists, align the 2 1/8 hole in the Template over it. Align the edge of the Template to be parallel with the edge of the door (Figure 2-2). The edge of the door maybe beveled, so the edge of the template may not line up exactly with the door edge, just make certain it is parallel to it. Figure 2-2 Template, RSTP21, on Metal Door 2.4.1.4 Tape the Template onto the door. 2.4.1.5 Center punch the center points of the holes (Figure 2-2). 2.4.1.6 To locate hole center points on the opposite side of the door, following instructions 2.4.1.3, 2.4.1.4, and 2.4.1.5 with Template on the other side of the door. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 9 of 37 2.4.2 Door Edge 2.4.2.1 Skip this section if the Latch Hole (Hole #1) is already drilled and the Optional Door Position Switch (Hole #2) is not being installed (Figure 2-3). 2.4.2.2 Mark a vertical center line on the door edge 37 to 39 from floor. Mark a horizontal line on the door edge that lines up with the horizontal line drawn on the door side in Section 2.4.1.1. 2.4.2.3 Align Template, RSTP21, on the door edge so that the center of the Latch Hole is at the intersection of the vertical center line and horizontal line drawn in Section 2.4.2.2 (Figure 2-3). 2.4.2.4 Align the edge of the Template to be parallel to the edge of the door and tape in place. 2.4.2.5 If the Latch Hole (Hole #1) does not exist, center punch its center point (Figure 2-3). 2.4.2.6 If the Optional Door Position Switch (Hole #2) is to be installed, center punch the correct center point for the size magnet to be installed (Figure 2-3). Figure 2-3 Template RSTP21 on Metal Door Edge P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 10 of 37 2.4.3 Doorjamb 2.4.3.1 If the strike is not mortised or if a door position switch is being used, mark a vertical line on the strike side of the doorjamb, one half the thickness of the door plus the thickness of any bumpers on the jamb away from the door stop of the doorjamb (D = door thickness + bumper thickness, Figure 2-4 & Figure 2-5). The vertical line must be in line with the Center Line of the door when the door is closed. Figure 2-4 Locating Center Line on Doorjamb (top view) 2.4.3.2 Mark a horizontal center line (Figure 2-5) on the door jamb that lines up with the horizontal center line on the door that intersects the center of the Chassis Hole on the door (Hole #2 in Figure 2-3). 2.4.3.3 Place Template, RSTP11, with the center of the Latch Hole over this 38 intersect. Align the center lines on the template with the center lines drawn on the doorjamb and tape it in place
(Figure 2-5). Figure 2-5 Template, RSTP21, on Doorjamb (side view) 2.4.3.4 Center punch the Latch Hole drill point. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 11 of 37 2.4.3.5 If the Optional Door Position Switch is being installed then center punch the Optional Door Position Magnet Hole (Figure 2-5). NOTE: It is very important that the Optional Door Position Magnet Hole on the doorjamb and the Optional Door Position Switch Hole on the door edge are center punched exactly opposite each other. Note: For UL installations that use a Door Position Switch use a UL listed door/window contact. Door contacts for door position monitoring are not for intrusion protection. 2.5 Drilling Holes Follow the instructions printed on the templates for drilling holes. Note: Some holes are only to be drilled on the reader side and some holes are transceiver side of the door Note: There is a template for a metal door (hollow core) and a different template for a wood door
(solid core). Make certain you have used the correct template!
Note: For UL installations that use a Door Position Switch use a UL listed door/window contact. Door contacts for door position monitoring are not for intrusion protection. 2.6 Marking & Drilling Transceiver Mounting Holes NOTE: Self tapping screws cannot be used to mount the Transceiver, therefore drill the Transceiver Mounting Holes as indicated below. 2.6.1 If install, remove the Transceiver Cover by removing the two secure Torx Reader Cover Mounting Cover Screws (6-23 x 3/8) (Figure 2-6). Figure 2-6 Transceiver Cover Screws P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 12 of 37 2.6.2 Position the Transceiver Base Plate so that it is flush against the inside of the door and that the lower right mounting hole on the Transceiver Base Plate lines up with the mark made from the template
(Figure 2-7). Make certain that the Transceiver Base Plates long side is vertically plumb or parallel with the doors edge, then mark the other three mounting holes. Remove the Transceiver Base Plate from the door and drill holes at these four locations. NOTE: Do not drill while the Transceiver Base Plate is still on the door!
NOTE: Do not install the Transceiver Base Plate at this time. Figure 2-7 Transceiver Mounting Holes P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 13 of 37 2.7 Marking & Drilling Reader Mounting Holes NOTE: Self tapping screws cannot be used to mount the Reader, therefore drill the Reader Mounting Holes as indicated below. 2.7.1 If install, remove the Reader Cover by removing the two secure Torx Reader Cover Mounting Cover Screws (6-23 x 3/8) (Figure 2-8). Figure 2-8 Reader Cover Screws P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 14 of 37 2.7.2 Position the Reader Base Plate so that it is flush against the outside of the door and that the lower right mounting hole on the Reader Base Plate lines up with the mark made from the template (Figure 2-9). Make certain that the Reader Base Plates long side is vertically plumb or parallel with the doors edge, then mark the other three mounting holes. Remove the Reader Base Plate from the door and drill holes at these four locations. NOTE: Do not drill while the Reader Base Plate is still on the door!
NOTE: Do not install the Reader Base Plate at this time. Figure 2-9 Reader Mounting Holes P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 15 of 37 2.8 Mortising for Latch 2.8.1 If not already done, mortise the edge of the door to accommodate the Latch & Faceplate (Figure 2-10). 2.8.2 Making certain that the Latch is properly oriented (Note: The Deadlocking Plunger of the Latch must face away from the Door Stop of the Door Jamb, Figure 2-11.), install the Latch & Faceplate with the two screws provided (Figure 2-10). Figure 2-10 Mortising Latch on Door Edge Figure 2-11 Latch Orientation on Door Edge P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 16 of 37 2.9 Installing the Optional Door Position Switch If the optional Door Position Switch is being used, feed the 2 wires of the supplied 3/4 diameter Door Position Switch through the Door Position Switch Hole in the edge of the door and then through the Reader Cable Hole to the inside side of the door (Figure 2-12). Press the reed switch into the hole so it is flush with the door edge. The two wires from the Door Position Switch will be connected after mounting the Transceiver, see Section 2.11, below. Figure 2-12 Installing the Door Position Switch P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 17 of 37 2.10 Mounting Transceiver The Transceiver consists of two major components: the Transceiver Cover (Figure 2-13) and the Transceiver Base Plate (Figure 2-14). The Transceiver is mounted on the inside of the door. NOTE: For maximum weather resistance, make certain that there is a foam gasket attached to the back side of the Transceiver Base Plate. Contact Recognition Source if the foam gasket is missing. Figure 2-13 Transceiver Cover Figure 2-14 Transceiver Base Plate Components 2.10.1 Before mounting the Transceiver, the Reader Cable, Motor & Request to Exit Cable, the optional Door Position Switch Wires, and Gray Ground Wire (ring terminal toward the Transceiver) must be routed into their appropriate locations (Figure 2-15). P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 18 of 37 Figure 2-15 Routing Transceiver Wires and Cables 2.10.1.1 Make certain that the Reader Cable is routed out the back of the Transceiver Base Plate in the opening just above the Battery Pack location (Reader/DPS Cable Entry/Exit, Figure 2-14). 2.10.1.2 Make certain that the Motor & Request to Exit Cable and Gray Ground Wire (ring terminal toward the Transceiver) are routed out the back of the Transceiver Base Plate in the opening at the bottom of the Transceiver Base Plate (Motor/RTX Cable Entry/Exit, Figure 2-14). 2.10.1.3 If installing on a metal door, install plastic Bushings in the Motor Cable hole and on Reader Cable Hole both the Transceiver and Reader Side, three bushings total (Figure 2-15). 2.10.1.4 The Reader Cable must be routed through the Reader Cable Hole from the inside of the door so that the Reader Cable extends to the outside of the door. It will be connected to the Reader in section 2.12, below. 2.10.1.5 The Motor & Request to Exit Cable and Gray Ground Wire (ring terminal toward the Transceiver) must be routed through the Motor & Request to Exit Cable Hole and down to the Lock Housing Hole. The route that this cable takes will depend on the type of door. If the door is solid core (i.e. wood), then there is a Diagonal Motor Cable Hole that is used. If the door is hollow core (i.e. metal), then the hollow core is used. See page three of template T147-008-001. 2.10.1.6 If the optional Door Position Switch is being installed, the wires coming from this switch should already be coming out the Reader Cable Hole and need to be routed through the Transceiver Base Plate in the opening just above the Battery Pack (Reader/DPS Cable Entry/Exit, Figure 2-14). P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 19 of 37 2.10.2 Being careful not to pinch any of the wires, position the Transceiver Base Plate so that it is flush against the inside of the door. Figure 2-16 Mounting Transceiver Base Plate Figure 2-17 Transceiver Grounding Screw Secure the Transceiver Base Plate to the door using the supplied wood/sheet metal screws (Figure 2-16), making certain that the Gray Ground Wire (ring terminal end) coming Lock Housing is securely fastened under Grounding Screw at the lower left (Figure 2-17). NOTE: Do not install the Battery Pack or Transceiver Cover at this time!
P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 20 of 37 2.11 Connecting Door Position Switch Wires 2.11.1 Cut and strip the Door Position Switch wires so that they can be neatly dressed and connected to the Door Position Connector on the Transceiver PCB (Figure 2-18). 2.11.2 Connect the two Door Position Switch wires to the Door Position Connector on the Transceiver PCB
(Figure 2-18). This connection is not polarized so either wire can go to either terminal. Figure 2-18 Connecting the Door Position Switch Wires P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 21 of 37 2.12 Mounting Reader The Reader consists of two major components: the Reader Cover (Figure 2-19) and the Reader Base Plate
(Figure 2-20). The Reader is mounted on the outside of the door. NOTE: For maximum weather resistance, make certain that there is a foam gasket attached to the back side of the Reader Base Plate. Contact Recognition Source if the foam gasket is missing. Figure 2-19 Reader Cover Components 2.12.1 If not already done, remove the Reader Cover by removing the two secure Torx Reader Cover Figure 2-20 Reader Base Plate Components Mounting Cover Screws (6-23 x 3/8) (Figure 2-21). Figure 2-21 Reader Cover Screws P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 22 of 37 2.12.2 Before mounting the Reader, the Reader Cable must be routed through Reader Cable Routing Hole on the Reader Base plate (Figure 2-22). Figure 2-22 Reader Cable Routing 2.12.2.1 If installing on a metal door, make certain that the plastic Bushing is installed in the Reader Hole on the Reader side of the door (Figure 2-22). 2.12.2.2 Route the Reader Cable from the Reader Hole in the door through the back of the reader into Reader Cable Routing Hole near the bottom of the Reader (Figure 2-22 & Figure 2-23). Figure 2-23 Reader Cable Connection 2.12.2.3 Connect the Reader Cable to the Reader Connector from the front side of the reader (Figure 2-23). P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 23 of 37 2.12.2.4 Dress the Reader Cable so that a minimum of cable is left on the front side of the reader and that all of the Reader Cable is above the Plastic Wall (Figure 2-24). This insures that the Reader Cable will not interfere when mounting the Reader Cover. Figure 2-24 Reader Cable Dressing 2.12.3 Being careful not to pinch any of the wires, position the Reader Base Plate so that it is flush against the outside of the door and secure the Reader Base Plate to the door using the supplied wood/sheet metal screws. 2.12.4 If the Reader Gasket (Figure 2-25) is not already mounted on the Reader Base Plate, position the Reader Gasket in the outer groove of the Reader Base Plate making certain that the ends of the Reader Gasket are at the bottom of the base plate and that there is a Weep Gap. Figure 2-25 Reader Gasket P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 24 of 37 2.12.5 If the Reader is equipped with an optional Request to Exit Switch (Figure 2-19), before installing the Reader Cover, route the Request to Enter switch wires through the Reader Cable Hole from the Reader side to the Transceiver side of the door. On the Transceiver side, connect the Request to Enter wires to the mating connector. Pull the excess Request to Enter wires toward the Transceiver side and from the Transceiver side dress any excess wires into the Reader Hole. 2.12.6 Install the Reader Cover and fasten with two secure T-10 Torx Reader Cover Mounting Screws (6-32 x 3/8) using the T-10 TORX L-key that is provided (Figure 2-21). 2.13 Adjusting Lockset to Door Thickness 2.13.1 Remove the Inside Lever by depressing the Lever Catch with the Wire Pin through the small hole in the Inside Rose and/or Inside Lever and pull Inside Lever off the Inside Lock Tube (Figure 2-28). Depress the Lever Catch again and remove the Inside Rose assembly (Figure 2-26). Figure 2-26 Removing Inside Lever & Inside Rose Assembly 2.13.2 Determine the doors thickness. Locksets will fit doors 1-5/8 to 1-7/8 thick. Locksets are factory assembled for 1-3/4 doors. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 25 of 37 2.13.3 To adjust, remove the outside lever (Figure 2-28). Screw the outside rose to the desired position. Use the DOOR THICKNESS GAUGE (provided with lockset) to confirm correct position for the desired door thickness. The mark on the gauge should line up with the center of the Retractor in the Housing
(Figure 2-27). Figure 2-27 Door Thickness Adjustment Figure 2-28 Exploded Lock Hardware 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 26 of 37 P/N: M053-xxx-x001 2.14 Placing the Lock Chassis into the Chassis Hole and Then Engaging the Retractor in Latch 2.14.1 Push the Lock Housing through the 2-1/8 Hole from the outside of the door, so that the Retractor in the Lock Housing engages the Latch Tail (Figure 2-29 & Figure 2-30). Make certain the Motor Wire Harness from the Motor and the Motor & Request to Exit Cable from the Transceiver are not pinched and are properly routed to the inside of the door for connection later. Note: Prongs must engage inside the Lock Housing. Figure 2-29 Inserting Lock Housing into the 2-1/8 Hole 2.14.2 Align the Outside Mounting Plate and Outside Rose so that the Rose Posts enter the Thru-Bolt holes in the door (Figure 2-28). 2.14.3 Check from the inside of the door to see if the Latch is properly engaged with the Latch Tail in the Retractor and the Prongs in the Lock Housing. Make certain that the Latch Tube Prongs engage Chassis Frame and Latch Tailpiece engages Retractor (Figure 2-30). Figure 2-30 Engaging Retractor & Latch P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 27 of 37 2.15 Connecting & Dressing the Motor, Request to Exit, & Ground Wires 2.15.1 Connect the Gray Wire (spade lug end) from the Transceiver Base to the Grounding Screw on the Lock Housing (Figure 2-31). NOTE: Only the top screw on the Lock Housing can be used as a Grounding Screw. Figure 2-31 Ground Wire Connection & Wire/Connector Holes 2.15.2 Connect the Motor Wires from the motor to the Motor Connector on the cable routed through the Upper Trim Hole coming from the Transceiver. The Motor Connector is unique and will only mate with the correct connector. 2.15.3 Connect the Request to Exit Wires from the Request to Exit Switch on the Inside Rose to the Request to Exit Connector on the cable routed through the Upper Motor Cable Hole coming from the Transceiver. The Request to Exit Connector is unique and will only mate with the correct connector. 2.15.4 Insert the mated Motor Connector into the Motor Connector Hole (Figure 2-31) on the located on the side of the 2-1/8 Lock Housing Hole. Pack and dress the Motor Cable so that the Inside Rose will not pinch it. 2.15.5 Insert the mated Request to Exit Connector into the Request to Exit Connector Hole (Figure 2-31) located just below the Motor Connector Hole. Pack and dress the Request to Exit Cable so that the Inside Rose will not pinch it. 2.15.6 Make certain that the cable is properly routed and dressed so that it will not be pinched when a Thu-
Bolt is installed in the Upper Trim Hole. 2.16 Installing the Inside Rose Assembly & Cover 2.16.1 Insert the Plastic Bushing (Figure 2-32) from the inside of the door into the Upper Trim Hole so that the Plastic Bushing slides over the top Outside Rose Post (Figure 2-28 & Figure 2-30). Make certain that the Plastic Bushing does not pinch any wires. The Plastic Bushing will protect the wires from being pinched when the Upper Thu-Bolt is installed in the following step. 2.16.2 Insert the Upper Thu-Bolt through the top hole of the Inside Rose and install the Inside Rose Assembly making certain that the Upper Thu-Bolt goes inside the Plastic Bushing (Figure 2-32). The Inside Rose may have to be wiggled to get the Plastic Bushing over the Inside Rose Post. Make certain all connectors and wires are properly routed and dressed so that no pinching occurs then fasten it to the Outside Rose with the two long Thru-Bolts (Figure 2-32). P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 28 of 37 Figure 2-32 Installing Inside Rose, Thru-Bolts and Cover 2.16.3 This step is easy to forget: Place the Stepped Plastic Washer (Figure 2-32), larger diameter first towards the door) over the Inside Lock Tube and into the Inside Rose (it snaps in). 2.16.4 Press the Inside Cover over the Inside Rose making certain that the Notch in the Inside Cover aligns with either Notch on the inside Rose. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 29 of 37 2.17 Installing the Inside Lever 2.17.1 Insert Cylinder Retainer into the Inside Lever (Figure 2-28). 2.17.2 With the level end towards the hinges, push the Inside Lever onto the Inside Lock Tube, slightly wiggle and push until the Inside Lever engages the Lever Catch on the Inside Rose (Figure 2-28). 2.17.3 Test the Inside Lever to insure that it is on securely. 2.18 Installing Strike Plate 2.18.1 Calculating the location of the Strike Plate Center Line will vary from door to door. It is basically of the door thickness from whatever stops the door when it is closed. Sometimes this is the door frame (jam) itself, sometimes it is a rubber bumper, and sometimes it is weather stripping. Determine what stops your door when it is closed and measure the doors thickness from that point and that is the Strike Plate Center Line location (Figure 2-33). Figure 2-33 Installing Strike Plate 2.18.2 Mortise the doorjamb to accommodate the Strike Box and Plate in alignment with the Strike Plate Center Line (Figure 2-33). The mortise must be deep enough so that the installed Strike Plate is flush with the Door Frame. 2.18.3 Insert the Strike Box and Plate and secure both with two screws provided. Note: Make certain that the Strike Plate is positioned so that the door will latch easily. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 30 of 37 2.19 Installing the Optional Door Position Magnet Note: The magnet that works with the Door Position Switch must get mounted exactly across from the Door Position Switch. Note: For UL installations that use a Door Position Switch use a UL listed door/window contact. Door contacts for door position monitoring are not for intrusion protection. 2.19.1 Insert the magnet into the hole drilled in section 2.4.3. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 31 of 37 2.20 Install the Battery Pack & Transceiver Cover 2.20.1 Install the new Battery Pack (Figure 2-34), install the Battery Bracket, and connect the Battery Pack
(Figure 2-35). Figure 2-34 MIRL Battery Pack Figure 2-35 MIRL Battery Pack Installation 2.20.2 If the Transceiver Gasket (Figure 2-36) is not already mounted on the Transceiver Base Plate, position the Transceiver Gasket in the outer groove of the Transceiver Base Plate making certain that the ends of the Reader Gasket are at the bottom of the base plate and that there is a Weep Gap. Figure 2-36 MIRL Transceiver Gasket P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 32 of 37 2.20.3 Install the MIRL Transceiver Cover and fasten with two secure T-10 TORX Transceiver Cover Mounting Screws (6-32 x 3/8) using the T-10 TORX L-key that is provided (Figure 2-37). Figure 2-37 MIRL Transceiver Cover This completes the installation of the MIRL Standard Cylindrical. If the Panel Interface Module (PIM) is not installed, now is the time to install it, please refer to the PIM Installation Manual. If the Panel Interface Module (PIM) is installed, then you are ready to configure your Wyreless Access System, please refer to the Configuring & Operating a Wyreless Access System manual. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 33 of 37 3. Troubleshooting Problem Levers pull off. Solution 1. Lever catch not engaging. Lock may not be centered or door too thick. 2. Cylinder retainer not flush. 3. Non-standard sized cylinder Unable to install outside lever. Key orientation incorrect Outside lever removable without using key. 1. Tailpiece installed in wrong orientation. 2. Wrong tailpiece. Latch wont retract. Key binds in lock. Incorrect retractor/latch engagement 1. 2. Poor door preparation or mis-aligned Thu-Bolts. 1. Lever catch not fully engaged. 2. Be sure outside rose is not adjusted too far outward. 3. Wrong tailpiece. Key cannot be removed from cylinder. Incorrect tailpiece alignment. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 34 of 37 For questions regarding Wyreless Access :
(630) 762-4450
(630) 762-4444 fax 4. Contacting Recognition Source P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 35 of 37 5. FCC/UL Compliance & Warnings 5.1 FCC Compliance This device has been authorized by the FCC Rules and Industry Canada. This device complies with the limits for a Class B digital device and a Class B intentional radiator, pursuant to Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Wyreless Access System Component must be installed by qualified professionals or contractors in accordance with FCC part 15.203, Antenna Requirements. Do not use any antenna other than the one provided with the unit. 5.2 UL Compliance The Modular Integrated Reader Lock (MIRL) Standard Cylindrical is listed under UL294 as an access control system accessory. Access equipment manufactured and/or sold by Recognition Source, LLC, is not rated for, or intended for use in place of life safety devices. For example, do not use a MIRL where a crash bar is required. When using the proximity version of the Modular Integrated Reader Lock, for UL installations, the lock has not been investigated for burglary protection. For UL installations that use a Door Position Switch use a UL listed door/window contact. Door contacts for door position monitoring are not for intrusion protection. No standby power provided. 5.3 Warnings RF Exposure - To comply with FCC RF exposure requirements for mobile transmitting devices this transmitter should only be used or installed at locations where there is normally at least a 20 cm separation between the antenna and all persons. Do not co-locate and operate in conjunction with any other antenna or transmitter. Use only the Battery Pack specified in this instruction manual. Do not subject Battery Pack to fire or high temperatures. Do not attempt to recharge, short out or disassemble Battery Pack. Follow local regulations for alkaline battery disposal. Immediately remove the batteries and discontinue use if:
the product is impacted after which the interior is exposed, or the product emits a strange smell, heat, or smoke. Changes or modifications not expressly approved by Recognition Source could void the users authority to operate the equipment. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 36 of 37 6. Revision History Version x001 Date 09/09/03 Changes preliminary in house release for comments P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 37 of 37
1 2 3 | WISI manual | Users Manual | 524.52 KiB | December 12 2003 / December 01 2004 |
PPPRRREEELLLIIIMMMIIINNNAAARRRYYY INSTALLATION INSTRUCTIONS WIRELESS INTEGRATED STRIKE INTERFACE
(WISI) 3820 Stern Avenue St. Charles, IL 60174 Phone: 630-762-4450 Fax: 630-762-4455 P/N: M053-xxx-x001 INSTALLATION INSTRUCTIONS Wireless Integrated Strike Interface (WISI) NOTE: These instructions are for installing the Wireless Integrated Strike Interface (WISI), a component of a Wyreless Access System. After completing this installation refer to the Configuring and Operating the Wyreless Access System manual. Table of Contents 2. 1. Wyreless AccessTM System Components........................................................................................................3 1.1 Overview .......................................................................................................................................................3 1.2 WISI Components & Sales Models ...............................................................................................................4 Installing the WISI ..........................................................................................................................................6 2.1 Tools Hardware Required...........................................................................................................................6 2.2 Determining the Best WPIM and WISI Locations ........................................................................................6 2.3 Mounting the WISI Components...................................................................................................................7 2.4 Connecting the Access Control Peripherals...................................................................................................8 Using the WISI Without a Card Reader......................................................................................................14 Battery Operated Strike Mechanical Specifications...................................................................................15 FCC/UL Compliance & Warnings...............................................................................................................17 5.1 FCC Compliance .........................................................................................................................................17 5.2 UL Compliance............................................................................................................................................17 5.3 Warnings......................................................................................................................................................17 Contacting Recognition Source ....................................................................................................................18 Revision History.............................................................................................................................................19 3. 4. 5. 6. 7. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 2 of 19 1. Wyreless AccessTM System Components 1.1 Overview Every access control system that uses Wyreless AccessTM contains two different types of modules (Figure 1-1):
at least one Wireless Panel Interface Module (WPIM), and at least one Wyreless Access Point Module (WAPM) Access Control Panel Wired Communication Wyreless Panel Interface Module
(WPIM) RF Communication Wyreless Access Point Module
(WAPM) Wired Communication Access Point Access Control Panel Location Access Point Location Figure 1-1 Wyreless Access System Block Diagram Recognition Sources product line contains several different expressions of each module. The WPIM is wired to the access control panel and ideally is installed very close to the access control panel. The WPIMs installation location is determined by the location of the WAPMs with which it will communicate using RF. The WAPM is installed at the access point where access will be controlled and/or monitored. Depending on the application and which WAPM is used, some wiring at the access control point may be required. Regardless of which WPIM or WAPM module is used, the communication link between the WPIM and WAPM is always RF. This manual describes the installation of a Wireless Integrated Strike Interface (WISI) which is a WAPM. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 3 of 19 1.2 WISI Components & Sales Models The WISI includes a Card Reader Assembly (HID proximity, magnetic, or Wiegand), a Control Transceiver Module, and a Battery Pack (located inside the Control Transceiver Module) (Figure 1-2 and Figure 1-3). If the access point where the WISI will be used requires a strike, then an optional Battery Operated Strike
(BOS) Assembly (Figure 1-2) must also be ordered. There is one BOS that is approved for the WISI. It comes with three faceplates for use with cylindrical locksets, mortise locksets without a deadbolt, or a mortise panic exit devices with or without a deadlatch. The BOS is available from Recognition Source as a BOS-100 or directly from Locknetics as a 9110 TRI-BP. NOTE: Using any other strike with the WISI may damage the Control Transceiver Module and will void the WISI warranty. Figure 1-2 WISI & Peripherals Figure 1-3 WISI Battery Pack P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 4 of 19 MODEL WISI-MS WISI-PROX CARD READER MOUNTING LOCATION Magnetic HID Proximity Surface Surface indoor indoor Table 1-1- WISI Sales Model Table MODEL BOS-100 9110 TRI-BP SUPPLIER LOCATION indoor indoor Table 1-2- WISI Battery Operated Strikes Recognition Source Locknetics P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 5 of 19 2. Installing the WISI 2.1 Tools Hardware Required Hammer 9/32 & 3/4 drill bits Flat and Phillips head screwdrivers (1/8 wide flat blade for screw terminals) Pencil Transceiver Control Box Mounting Kit (K381-000-001), provided, including four zinc, pan head Phillips, 8-18 X 1 sheet metal screws and four heavy-duty anchors Card Reader Mounting Kit (K384-002-001), provided, including two black, flat head Phillips, 8-18 X 1 sheet metal screws and two heavy-duty anchors 2.2 Determining the Best WPIM and WISI Locations Proper selection of WPIM and WISI Transceiver Control Box mounting locations insures reliable RF communications. The WPIM manual contains a section for determining the best location for the WPIM. The maximum distance between WPIM and a WISI is 200 horizontally when installed inside a building on the same floor that uses normal building construction materials. Never locate the WISI and WPIM more than one (1) floor apart. If on different floors, limit the maximum horizontal distance to 100. The maximum distance is 1000 for a line of sight installation. This section provides additional application specific help and guidelines to select the best mounting location for the WISI Transceiver Control Box:
Mount the WISI Transceiver Control Box inside the protected area. Mount the WISI Transceiver Control Box on the wall, at least 55 from the floor Mount the WISI Transceiver Control Box within 6 cable feet of the Card Reader If a Battery Operated Strike is used, mount the WISI Transceiver Control Box within 15 cable feet of the Strike. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 6 of 19 2.3 Mounting the WISI Components 2.3.1 TRANSCEIVER CONTROL BOX A 1 hole is provided in the back of the Transceiver Control Box for routing wires in & out. If needed, additional hole(s) can be drilled in the lower left hand corner of the Transceiver Control Box. Wire routing inside the enclosure is very important. Improper wire routing will reduce the RF range. Keep the wires inside the enclosure as short as possible (i.e. do not coil any excess wire inside the enclosure) (Figure 2-1 & Figure 2-2). NOTE: Do not run wires across the printed circuit board. Figure 2-1 Improper Wire Routing Figure 2-2 Proper Wire Routing 2.3.1.1 Remove the Transceiver Control Box cover. 2.3.1.2 Place the Transceiver Control Box (cover removed) against the wall in the position it was successfully link tested. 2.3.1.3 Using Transceiver Control Box as a template, mark the four corner mounting holes and the wire hole (if used) with a pencil. 2.3.1.4 Drill a 9/32 hole at each mounting mark, 1 deep, and a hole at the wire hole mark (if used). 2.3.1.5 Insert the four anchors provided firmly into the holes so they are flush with the wall. 2.3.1.6 Depending on the installation, you may want to screw the Transceiver Control Box to the wall now or wait until the rest of the components are installed to facilitate wire routing. 2.3.2 CARD READER Using the Card Reader Hole Drilling Template (Error! Reference source not found.), mark the wall for the 9/32 mounting holes, and the 3/4 wiring hole. The WISI package contains screws for drywall mounting. If you have a different mounting surface than drywall, you will need to provide suitable mounting hardware, and determine the proper hole size. Route the Card Reader wires into the Transceiver Control Box. 2.3.3 BATTERY OPERATED STRIKE - If the installation uses a strike, mount the strike assembly into the door jamb. Follow the directions packaged with the strike assembly (also refer to section 4, page15). Route the strike wires into the Transceiver Control Box. 2.3.4 DOOR POSITION SWITCH If the installation uses a door position switch, mount it using the manufacturers installation instructions. Route the door position switch wires into the Transceiver Control Box. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 7 of 19 2.3.5 REQUEST TO EXIT DEVICE If the installation uses a separate request to exit device, mount it using the manufacturers installation instructions. Route the request to exit device wires into the Transceiver Control Box. NOTE: The only recommended Request To Exit Device to use with a WISI is a momentary switch. Unless powered from a separate source using a powered device like a PIR will result in a very short battery life. 2.3.6 REQUEST TO ENTER DEVICE If the installation uses a request to enter device, mount it using the manufacturers installation instructions. Route the request to enter device wires into the Transceiver Control Box. NOTE: The only recommended Request To Enter Device to use with a WISI is a momentary switch. Unless powered from a separate source using a powered device like a PIR will result in a very short battery life. 2.4 Connecting the Access Control Peripherals The access control peripherals for the WISI are connected to the Transceiver Control PCB via two 10 terminal connectors, J3 & J4 (Figure 2-3 & Figure 2-4). Figure 2-3 WISI Transceiver Control Box with Cover Removed P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 8 of 19 Figure 2-4 WISI Typical Wiring Diagram P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 9 of 19 2.4.1 CARD READER NOTE: Use only the supplied Card Reader. If the WISI is to be used without a Card Reader, please refer to section 3, page 14, below. The Card Reader connects to the Transceiver Control Module through J3 using 10 wires. The Card Reader Assembly is shipped with the mating J3 connector already installed on the end of a 6 cable. If this cable length is acceptable for the installation, then just plug the mating connector into J3. If the cable needs to be shortened, remove the mating connector, shorten the cable to the desired length, strip the wires, tin the wires, and reconnect the wires to the mating connector following the information in Table 2-1. WISI Terminal J3 GRN_LED RED_LED BEEPER DCJ_POS RDR_CLK RDR_DAT CARD_PRES RDR_PWR PROX_PWR GND Card Reader Cable Wire ORANGE BROWN YELLOW BLUE WHITE GREEN PURPLE GRAY RED BLACK Description Card Readers green LED control Card Readers red LED control Card Readers beeper control Card Readers positive DC jack terminal Card Readers clock or data1 signal Card Readers data or data0 signal Card Readers card present signal Card Readers positive DC power (switched) Card Readers positive DC power for proximity reader (non-switched) Card Readers DC ground 2.4.2 BATTERY OPERATED STRIKE Table 2-1 Card Reader Connector (J3) If used, the Battery Operated Strike connects to the Transceiver Control Module through J4 using 2 wires. The Battery Operated Strike is shipped with a 15 cable. Trim the cable to the desired length, strip the wires, tin the wires, and connect the wires to the mating connector following the information in Table 2-2. The color of the wires provided with the strike can not be guaranteed to be black and white. If this is the case, take your best guess (a 50/50 chance), connect the two wires from the strike in any order. If the strike unlocks when it should lock or locks when it should unlock, then switch the wires. No damage will be done, you just wont get the proper lock/unlock operation. WISI Terminal J4 STK_LK STK_UL Battery Operated Strike Wire BLACK WHITE Description If the Battery Operated Strike wires are not black and white, see text above. Table 2-2 Battery Operated Strike Connections (J4) P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 10 of 19 2.4.3 DOOR POSITION SWITCH If used, a Door Position Switch connects to the Transceiver Control Module through J4 using 2 wires. Trim the cable to the desired length, strip the wires, tin the wires, and connect the wires to the mating connector following the information in Table 2-3. Either wire can go to either connection, i.e. the connection is non-polar. WISI Terminal DR_POS_A DR_POS_B J4 Description A dry contact closure across these terminals indicates to the ACP that the access point portal is closed. An open circuit indicates to the ACP that the access point portal is open. Table 2-3 Door Position Switch Connections (J4) 2.4.4 REQUEST TO EXIT DEVICE NOTE: The only recommended Request To Exit Device to use with a WISI is a momentary switch. Unless powered from a separate source using a powered device like a PIR will result in a very short battery life. If used, a Request To Exit Device connects to the Transceiver Control Module through J4 using 2 wires. Trim the cable to the desired length, strip the wires, tin the wires, and connect the wires to the mating connector following the information in Table 2-4. Either wire can go to either connection, i.e. the connection is non-polar. WISI Terminal RT_EXIT_A RT_EXIT_B J4 Description A dry contact closure across these terminals initiates a request to exit. Table 2-4 Request To Exit Device Connections (J4) 2.4.5 REQUEST TO ENTER DEVICE NOTE: The only recommended Request To Enter Device to use with a WISI is a momentary switch. Unless powered from a separate source using a powered device like a PIR will result in a very short battery life. If used, a Request To Enter Device connects to the Transceiver Control Module through J4 using 2 wires. Trim the cable to the desired length, strip the wires, tin the wires, and connect the wires to the mating connector following the information in Table 2-5. Either wire can go to either connection, i.e. the connection is non-polar. WISI Terminal RT_ENT_A RT_ENT_B J4 Description A dry contact closure across these terminals initiates a request to enter. Table 2-5 Request To Enter Device Connections (J4) P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 11 of 19 2.4.6 BATTERY PACK INSTALLATION The Transceiver Control Module is shipped with a Battery Pack with a connector attached but maybe unconnected (Figure 1-3 & Figure 2-3). 2.4.6.1 If the WISI enclosure cover is on, use the Phillips screwdriver to remove WISI cover. There are 4 cover screws, one in each corner (Figure 1-2). 2.4.6.2 Install the Battery Pack into the Transceiver Control Module enclosure using the Velcro provided (Figure 2-5). Figure 2-5 Positioning the Battery Pack to Connect the Wires 2.4.6.3 Connect the Battery Pack Connector to its mating connector that is factory connected to J4
(Figure 2-6). Figure 2-6 Battery Pack Installed 2.4.6.4 Do not install the WISI cover at this time. The WISI needs to be linked before installing the WISI cover, follow the instructions in the Configuring & Operating a Wyreless Access System manual. WISI Terminal J4
+12V GND Battery Connector Wire RED BLACK Description Positive battery pack wire to this terminal Negative battery pack wire to this terminal Table 2-6 Battery Pack Connections (J4) P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 12 of 19 This completes the installation of the WISI. Do not install the WISI cover yet, this will be done after the Panel Interface Module (PIM) is installed and during system configuration. If the Wireless Panel Interface Module (WPIM) that will control this WISI is not installed, now is the time to install it, please refer to the PIM Installation Instruction manual. If the WPIM is installed, then you are ready to configure your Wyreless Access System, please refer to the Configuring & Operating a Wyreless Access System manual. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 13 of 19 3. Using the WISI Without a Card Reader The WISI is usually installed with the Card Reader that is supplied with the WISI. Some applications may not require the Card Reader, such as an access point that only needs a strike or an access point that just needs a Request to Exit or Door Position switches. When the WISI application does not require a card reader, two jumpers need to be added to the Card Reader Connector (J3) to insure that the WISIs DC current draw is minimized to maximize the battery life. The two reader signal connections, RDR_CLK & RDR_DAT, need to be grounded by jumping them to the GND connection (Table 3-1 & Figure 3-1). WCM Terminal Description RDR_CLK Card Readers clock or data1 signal RDR_DAT Card Readers data or data0 signal J3 GND Card Readers DC ground Table 3-1 WISI Card Reader Connector Figure 3-1 WISI Without Card Reader Jumpers P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 14 of 19 4. Battery Operated Strike Mechanical Specifications Figure 4-1, Figure 4-2, and Figure 4-3 show the mechanical dimensions of the battery operated strike (BOS-
100). These figures are provided for convenience only and the documentation provided with the strike should be used for actual installation dimensions. Figure 4-1 BOS-100 Perspective View Figure 4-2 BOS-100 Door Jamb Preparation Dimensions P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 15 of 19 Figure 4-3 BOS-100 Top View Dimensions P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 16 of 19 5. FCC/UL Compliance & Warnings 5.1 FCC Compliance This device has been authorized by the FCC Rules and Industry Canada. This device complies with the limits for a Class B digital device and a Class B intentional radiator, pursuant to Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Wyreless Access System Component must be installed by qualified professionals or contractors in accordance with FCC part 15.203, Antenna Requirements. Do not use any antenna other than the one provided with the unit. 5.2 UL Compliance The Wireless Integrated Strike Interface (WISI) listing under UL294 as an access control system accessory. Access equipment manufactured and/or sold by Recognition Source, LLC, is not rated for, or intended for use in life safety installations. The Wireless Integrated Strike Interface (WISI) shall not be installed in the fail-secure mode unless permitted by the local authority having jurisdiction and shall not interfere with the operation of panic hardware. The Wireless Integrated Strike Interface (WISI) shall only be installed where free egress is always allowed. 5.3 Warnings RF Exposure - To comply with FCC RF exposure requirements for mobile transmitting devices this transmitter should only be used or installed at locations where there is normally at least a 20 cm separation between the antenna and all persons. Do not co-locate and operate in conjunction with any other antenna or transmitter. Use only the Battery Pack specified in this instruction manual. Do not subject Battery Pack to fire or high temperatures. Do not attempt to recharge, short out or disassemble Battery Pack. Follow local regulations for alkaline battery disposal. Immediately remove the batteries and discontinue use if:
- the product is impacted after which the interior is exposed, or
- the product emits a strange smell, heat, or smoke. Changes or modifications not expressly approved by Recognition Source could void the users authority to operate the equipment. P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 17 of 19 6. Contacting Recognition Source
(630) 762-4450
(630) 762-4444 fax For questions regarding Wyreless Access:
P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 18 of 19 7. Revision History Version x001 Date 11/26/03 Changes preliminary in house release for comments P/N: M053-xxx-x001 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 19 of 19
1 2 3 | WPR manual | Users Manual | 269.95 KiB | December 12 2003 / December 01 2004 |
PPPRRREEELLLIIIMMMIIINNNAAARRRYYY INSTALLATION INSTRUCTIONS WYRELESS PORTABLE READER
(WPR) 3820 Stern Avenue St. Charles, IL 60164 Phone: 630-762-4450 Fax: 630-762-4455 P/N: M053-xxx-x001.1 INSTALLATION INSTRUCTIONS Wyreless Portable Reader (WPR) NOTE: These instructions are for installing a Wyreless Portable Reader (WPR), a component of a Wyreless Access System. After completing this installation refer to the Configuring and Operating the Wyreless Access System manual. Table of Contents 2. 1. Wyreless AccessTM System Components............................................................................................................3 1.1 Overview .......................................................................................................................................................3 1.2 Wyreless Portable Reader (WPR) Components.............................................................................................4 Installing the Wyreless Portable Reader (WPR) ..............................................................................................5 2.1 Tool Required................................................................................................................................................5 2.2 WPR Battery Installation/Replacement .........................................................................................................5 3. Contacting Recognition Source ..........................................................................................................................7 4. FCC Compliance & Warnings............................................................................................................................8 4.1 FCC Compliance ...........................................................................................................................................8 4.2 Warnings........................................................................................................................................................8 5. Revision History...................................................................................................................................................9 P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 2 of 9 1. Wyreless AccessTM System Components 1.1 Overview Every access control system that uses Wyreless AccessTM contains two different types of modules (Figure 1-1):
at least one Wyreless Panel Interface Module (WPIM), and at least one Wyreless Access Point Module (WAPM) Figure 1-1 Wyreless Access System Block Diagram Recognition Sources product line contains several different expressions of each module. The WPIM is wired to the access control panel and ideally is installed very close to the access control panel. The WPIMs installation location is determined by the location of the WAPMs with which it will communicate using RF. The WAPM is installed at the access point where access will be controlled and/or monitored. Depending on the application and which WAPM is used, some wiring at the access control point may be required. Regardless of which WPIM or WAPM module is used, the communication link between the WPIM and WAPM is always RF. This manual describes the installation of a Wyreless Portable Reader (WPR) which is a WAPM. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 3 of 9 1.2 Wyreless Portable Reader (WPR) Components Figure 1-2 Wyreless Portable Reader (WPR) with Proximity Reader The WPR includes 4 components:
WPR card reader (Figure 1-2), WPR on/off switch (Figure 1-2), WPR battery pack (Figure 1-3), WPR RF transceiver (Figure 1-4). Figure 1-3 WPR Battery Pack Figure 1-4 WPR RF Transceiver P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 4 of 9 2. Installing the Wyreless Portable Reader (WPR) Since the WPR is portable, no installation is required. The WPR is normally shipped with a battery installed and therefore it is ready for configuration right out of the box and the rest of this section can be skipped. If a battery is not installed or needs replacing, please follow the instructions in the following sections:
2.1 Tool Required Phillips head screwdriver 2.2 Determining the Best WPIM and WPR Locations Proper selection of the WPIM mounting location relative to the use area of the WPR insures reliable RF communications. Since the WPR is portable, determining best location for the WPIM is very important in achieving optimum performance. The WPIM manual contains a section for determining the best location for the WPIM. The maximum distance between WPIM and a WPR is 200 horizontally when on the same floor inside a building that uses normal building construction materials. Never operate the WPR more than one (1) floor from the WPIM antenna. If this is the case then reduce the horizontal distance to 100 maximum. The maximum distance is 1000 for a line of sight installation. 2.3 WPR Battery Installation/Replacement 2.3.1 Use the Phillips screwdriver to remove WPR cover. There are 4 cover screws, one in each corner
(Figure 1-2). 2.3.2 If a Battery Pack is being replaced, locate the used Battery Pack (Figure 2-4), disconnect the used Battery Pack (Figure 2-2), remove the used Battery Pack from its Velcro Strips (Figure 2-1) P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 5 of 9 2.3.3 Attach a new Battery Pack to the housing using the Velcro strips (Figure 2-1& Figure 2-2). Figure 2-1 Battery Pack Velcro Strips Figure 2-2 Battery Pack Positioned 2.3.4 Connect the battery connector to the mating connector coming from the transceiver board (Figure 2-3
& Figure 2-4). Figure 2-3 Battery Connector Figure 2-4 Battery Pack Connected 2.3.5 To continue to use the WPR on the same RF channel and with the same WPIM, re-install the cover, making certain that no wires are pinched. The cover should go on easy with no interferences. Replace the 4 cover screws, one in each corner (Figure 1-2). If the WPR needs to be re-linked or the RF channel needs to be changed, before re-installing the WPR cover, follow the instructions in the Configuring & Operating a Wyreless Access System manual. This completes the battery installation/replacement for the WPR. Do not turn on the WPR yet, this will be done after the Wyreless Panel Interface Module (WPIM) is installed and during system configuration. If the Wyreless Panel Interface Module (WPIM) is not installed, now is the time to install it, please refer to the WPIM Installation Manual. If the Wyreless Panel Interface Module (WPIM) is installed, then you are ready to configure your Wyreless Access System, please refer to the Configuring & Operating a Wyreless Access System manual. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 6 of 9 For questions regarding Wyreless Access :
(630) 762-4450
(630) 762-4444 fax 3. Contacting Recognition Source P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 7 of 9 4. FCC Compliance & Warnings 4.1 FCC Compliance This device has been authorized by the FCC Rules and Industry Canada. This device complies with the limits for a Class B digital device and a Class B intentional radiator, pursuant to Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Wyreless Access System Component must be installed by qualified professionals or contractors in accordance with FCC part 15.203, Antenna Requirements. Do not use any antenna other than the one provided with the unit. 4.2 Warnings RF Exposure - To comply with FCC RF exposure requirements for mobile transmitting devices this transmitter should only be used or installed at locations where there is normally at least a 20 cm separation between the antenna and all persons. Do not co-locate and operate in conjunction with any other antenna or transmitter. Use only the Battery Pack specified in this instruction manual. Do not subject Battery Pack to fire or high temperatures. Do not attempt to recharge, short out or disassemble Battery Pack. Follow local regulations for alkaline battery disposal. Immediately remove the batteries and discontinue use if:
- the product is impacted after which the interior is exposed, or
- the product emits a strange smell, heat, or smoke. Changes or modifications not expressly approved by Recognition Source could void the users authority to operate the equipment. P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 8 of 9 5. Revision History Version x001 X001.1 Date 11/25/03 12/01/03 Changes preliminary in house release for comments changed to plastic WPR handle P/N: M053-xxx-x001.1 3820 Stern Avenue St. Charles, IL 60174
(630) 762-4450
(630) 762-4444 fax Page 9 of 9
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2004-01-12 | 902 ~ 928 | DSS - Part 15 Spread Spectrum Transmitter | Class II permissive change or modification of presently authorized equipment |
2 | 2003-10-20 | 902 ~ 928 | DSS - Part 15 Spread Spectrum Transmitter | |
3 | 2001-07-01 | 902 ~ 928 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 | Effective |
2004-01-12
|
||||
1 2 3 |
2003-10-20
|
|||||
1 2 3 |
2001-07-01
|
|||||
1 2 3 | Applicant's complete, legal business name |
Recognition Source, LLC
|
||||
1 2 3 | FCC Registration Number (FRN) |
0018919456
|
||||
1 2 3 | Physical Address |
3820 Stern Avenue
|
||||
1 2 3 |
St, Charles, Illinois 60174
|
|||||
1 2 3 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 | TCB Application Email Address |
c******@curtis-straus.com
|
||||
1 2 3 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 3 | Grantee Code |
PM7
|
||||
1 2 3 | Equipment Product Code |
IRL2001
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 | Name |
G****** S****
|
||||
1 2 3 | Title |
Vice President of Engineering
|
||||
1 2 3 | Telephone Number |
630-7********
|
||||
1 2 3 | Fax Number |
630-7********
|
||||
1 2 3 |
g******@recognition-source.com
|
|||||
app s | Technical Contact | |||||
1 2 3 | Firm Name |
Radiometrics Midwest Corporation
|
||||
1 2 3 | Name |
J******** R**** S****
|
||||
1 2 3 | Physical Address |
12 East Devonwood Av.
|
||||
1 2 3 |
Romeoville, Illinois 60446
|
|||||
1 2 3 |
United States
|
|||||
1 2 3 | Telephone Number |
815-2********
|
||||
1 2 3 | Fax Number |
815-2********
|
||||
1 2 3 |
j******@radiomet.com
|
|||||
app s | Non Technical Contact | |||||
1 2 3 | Firm Name |
Radiometrics Midwest Corporation
|
||||
1 2 3 | Name |
J******** E**** S********
|
||||
1 2 3 | Physical Address |
12 East Devonwood Av.
|
||||
1 2 3 |
Romeoville, Illinois 60446
|
|||||
1 2 3 |
United States
|
|||||
1 2 3 | Telephone Number |
815-2********
|
||||
1 2 3 | Fax Number |
815-2********
|
||||
1 2 3 |
j******@radiomet.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 3 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 2 3 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Modular integrated reader/lock | ||||
1 2 3 | Access System Transmitter | |||||
1 2 3 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 | Modular Equipment Type | Single Modular Approval | ||||
1 2 3 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 3 | Original Equipment | |||||
1 2 3 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 3 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | Yes | ||||
1 2 3 | No | |||||
1 2 3 | Grant Comments | Grant Conditions - The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 3 | Grant Conditions The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 3 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 | Firm Name |
Radiometrics Midwest Corporation
|
||||
1 2 3 |
LS Research, LLC
|
|||||
1 2 3 | Name |
J****** S********
|
||||
1 2 3 |
R******** U****
|
|||||
1 2 3 | Telephone Number |
815-2********
|
||||
1 2 3 |
262-3********
|
|||||
1 2 3 | Fax Number |
815-2********
|
||||
1 2 3 |
262-3********
|
|||||
1 2 3 |
r******@lsr.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 902.00000000 | 928.00000000 | 0.2000000 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 902.00000000 | 928.00000000 | 0.2000000 | N/A | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15C | 902.00000000 | 928.00000000 | 0.2000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC