OBSBOT ORB-2205-CT Tail Air Remote Controller Design Specification Version: V1.0 1.0 Introduction 1.1 Component Description 1. Power button gyroscope. 2. Laser emitter hole 9. Select/Cancel person tracking 3. Status indicator light 10. Laser button Single click: laser;
4. Camera control wheel (controls double click: execute/cancel AI mode zoom) 11. Select/Cancel animal tracking 5. Multi-camera switching 12. Preset position 1/2/3 Single click:
6. Focus/Take photo Half-press for trigger preset position; long press:
focus; press fully to take photo add preset position 7. Record/Stop 13. Remote control sleep/wake 8. Gimbal control Four-way control of toggle button gimbal movement; single click to 14. Camera switch 1/2/3 Single click:
reset gimbal; long press to activate control camera (green light); double click: output camera video stream Light off Tail Air not connected
(red light). If output and control are on the same White Tail Air connected device, the red light will remain on. light 15. Customizable button Red light Camera output in Can be customized for function progress 16. USB-C interface Green Current remote control light can control the camera 1.2 Pairing method The following is the manual pairing method for the remote control and Tail Air:
Prerequisites Operation Enter pairing Quickly press the "" power button on the Tail Air three times, mode and the status indicator light "" on the Tail Air will turn into a flashing blue light. At the same time, press and hold the remote control's Person Tracking+1 dual keys for 3 seconds, and the indicator light "" on the remote control will change from steady to flashing to enter Bluetooth pairing mode. Release the keys, and the indicator light will continue to flash. Note: The Bluetooth remote control supports multiple connections to the Tail Air. Use the Person Tracking+ different device keys to pair, for example: If you use the remote control's Person Tracking+1 key combination to pair, the current Tail Air will be configured as device 1. If you use the remote control's Person Tracking+2 key combination to pair, the current Tail Air will be configured as device 2. If you use the remote control's Person Tracking+3 key combination to pair, the current Tail Air will be configured as device 3. Pairing status Pairing successful: The Tail Air returns to its state before entering Bluetooth pairing mode, with the blue light no longer flashing. The indicator light on the remote control flashes three times quickly and then goes off. The corresponding button on the remote control can control the device with a steady green light, while other added devices will have a steady white light. If a device is not added or if an added device is not turned on, the light will not turn on. Pairing failed: The Tail Air indicator light will flash blue for 30 seconds, then flash red three times quickly and exit pairing mode. The indicator light on the remote control will flash for 30 seconds, then flash red three times quickly and exit pairing mode. 1.2 Attention LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. FCC compliance statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. ISED Canada compliance statements:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication. The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with minimum distance 0mm between the radiator & your body. L'appareil a t valu pour rpondre aux exigences gnrales d'exposition aux RF. Cet quipement doit tre install et utilis avec une distance minimale de 0 mm entre le radiateur et votre corps.