RCS Model SCG5 Z-Wave Keypad INSTALLATION AND OPERATION MANUAL DCN: 141-02273-01 5/19/15 Model: SCG5 Z-Wave Keypad This manual applies to the following product revisions or later revisions up to the next manual revision release:
Product Z-Wave Keypad Document Revision History Firmware Revision 1.00.3 Part No:
001-02273 Revision 01 Date 10/20/10 Changes Original release Product Specifications Product Model:
Product:
Keypad Size:
Display:
Backlight:
Contrast:
Buttons:
Power:
Communications:
SCG5 Scene Control Z-Wave RF communications enabled 3.5 wide x 4.5 height x 1.2 depth Graphical LCD, 2.75 x 1.5, 64x128 pixel Yes, Blue/white, Controllable, on, off, timeout Adjustable on screen 8 2 AAA Alkaline Z-Wave RF DCN: 141-02273-01 5/19/15 2 Table of Contents Overview ...................................................................................................................................................... 4 Z-Wave Installation ................................................................................................................................... 5 Inclusion and Exclusion ............................................................................................................................. 5 Power ......................................................................................................................................................... 5 FCC ............................................................................................................................................................... 6 DCN: 141-02273-01 5/19/15 3 Overview button labels On-screen dynamic Function Control Buttons Z-Wave Keypad The Z-Wave Keypad provides for typical Keypad control plus has the added feature of Z-Wave communications for remote control. The Keypad has a large, backlit graphical display and control buttons. The Keypad can display multiple screens for different functions of the Keypad. Display operation Keypad control screen Normally the Keypad displays the Keypad control screen as shown above. Minimized Display Mode Optionally, you can set the Keypad to timeout and show a blank screen. Backlight The Keypad has a backlit display for low light and night visibility. It can be set to remain on constantly, or to turn off after a 20-120 second delay. These are selectable in the User Settings menu. Function Control Buttons The Keypads buttons are Soft Keys meaning that they change functions when you change screens. The function of the button is defined by on-screen labels that are dynamic and change when you change screens DCN: 141-02273-01 5/19/15 4 Z-Wave Installation Z-Wave controllers from various manufacturers may support the Z-Wave Wall Controller Device class used by the RCS Z-WAVE Keypad. The following procedure will allow the Keypad to be added to a Z-
Wave network. General Programming Procedure (for controllers supporting the Keypad device class):
1. Set your primary controller to Include mode, to add the Keypad as a node on your network
(see your controllers user manual for detailed instructions). 2. In the Keypads Main Menu, scroll down to the ZWave Install item. Select the item. 3. Press the YES button in the ZWave Install screen. Your controller will indicate the Keypad was successfully added to its network (see your controllers user manual for details). Also you can check if the Keypad was successfully added to the network by checking the ZHID (Home ID) and ZNID (Node ID) located in the Keypad Info screen. For other specific tasks such as adding the Keypad to Scenes or Groups, or deleting the Keypad from an existing network, use the Z-Wave Install procedure. Note: Before adding the Keypad to a Z-Wave Network, check that it does not already belong to one by viewing the Home and Zone IDs located in the Keypad Info screen. An un-configured Keypad should show zeros for both the Home and Zone IDs. Consult your controllers user manual for details on removing a device from a Z-Wave network. Inclusion and Exclusion Inclusion or exclusion is started by putting the controller into add node or remove node state and performing the General Programming Procedure outlined above. As part of the process, the Keypad sends a node information frame at normal power. Low power inclusion or low power exclusion is not possible. Power The Keypad requires 2 AAA Alkaline batteries DCN: 141-02273-01 5/19/15 5 FCC/IC INFORMATION TO USER Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device m ay not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. DCN: 141-02273-01 5/19/15 6