FCC ID: U5X-RE663 LED Keypad

RE663 LED Keypad Connect+ Encrypted IN S TA L L G U I D E LED Keypad is a table or wall mounted interface that chimes and uses lit keys and an LED light bar to provide visual arming status. The LED Keypad can be battery operated or AC powered for flexible installs. Features Displays real-time status Wall or table mount AC or battery primary power 1 year battery life for battery primary power User replaceable AA batteries Enroll by placing the panel and LED Keypad into wireless enrollment mode. Press the enroll button on the side of the panel to put the panel into wireless enrollment mode. Hold 1 and 3 simultaneously for 3 seconds on the Keypad to put the Keypad into wireless enrollment mode. Operate using the LED Keypad buttons. Light bar Night - Blue). Indicates arming level with color (Disarm - Green, Stay - Cyan, Away - Red, Amber corners indicate trouble condition. AC powered operation uses full light bar. Light bar "breathes" if zones are open. Battery operation uses light bar corners. Light bar blinks periodically and will double blink periodically if zones are open. Disarm Indicates Disarmed Cancel Force Arm Silence Trouble beeps

(w/code if required*) 0-9/User Code Disarm Force Arm Arm if required*

Silence Trouble beeps if required*

Press and hold 1 & 3 for

(Un)Enrollment

*Depends on panel settings

(Quick Arm, UL, etc.) Stay/Away/Night Change/Indicates Arming Level Hold Night for 3 seconds to turn display off Silent Arm Silent Arm or Disarm Modifier Press and hold with number to change volume Instant Arm No Entry Delay Modifier Press and hold with number to change brightness Panic Alarm Trigger Press and hold the * and #

buttons for 3 seconds Use the panel installation guide to verify proper system setup. I Keypad Mounting Options Table Top Mounting 1. Insert batteries into Keypad following polarity markings. 2. Route power cable through wire window in table stand. Connect the power supply by inserting the barrel plug into the black port. Orient the barrel plug as shown. Wire window Barrel plug 3. Insert the Keypad into the table stand. Push any extra wire into stand before inserting into stand. Slide the Keypad on stand until it "clicks" into place. 4. Coil up the excess power wire into the stand. Insert wire into wire holder and close stand cover to contain excess wires. Wire holder 5. Plug in power supply. Wall Mounting 1. Insert batteries into Keypad following polarity markings. 2. Fasten to wall by screwing the screws through the two holes into the wall. Screws should be fastened to a stud, a single gang box, or with wall anchors into drywall. Ensure power supply wires are routed through wire window and seated in wire channel if wire does not run behind drywall. Screw hole Screw hole Wire window Wire channel 3. Route power cable using one of two methods. A. Wires to Terminal Block: Connect one end of the wires to the terminal block. Splice the other end of the wires to the provided power supply. Polarity does not matter. MUST USE PROVIDED POWER SUPPLY. Wire lengths must not exceed lengths listed below. Terminal block B. Barrel Plug: Connect the power supply by inserting the barrel plug into the black port. Orient the connector as shown. WIRE GAUGE MAXIMUM LENGTH BETWEEN POWER SUPPLY AND KEYPAD

#24

#22

#20

#18

#16 Up to 50 feet Up to 100 feet Up to 150 feet Up to 250 feet Up to 400 feet Barrel plug 4. Insert the Keypad into the mounting plate. Push any extra wire behind wall plate before inserting into mounting plate. Slide the Keypad on plate until it "clicks" into place. 5. Plug in power supply. Pro Tips Wire can be hidden by running the wires through a hole behind the wall mounting plate and along the back side of the drywall to a location with an outlet. Switching to battery primary power can be done by restarting the keypad with the battery power. First, remove wall power supply and batteries. Wait 10 seconds. Then, power the keypad back up with only batteries. Unenrollment can be done by following the same steps as enrollment. Force unenroll can be done when no panel is present. Hold the 1 and 3 keys simultaneously to enter unenrollment mode. After the keypad fails to unenroll, hold the 1 and 3 keys simultaneously again to force unenroll. Specifications Physical Environmental Operating Temperature Maximum Humidity Device Specifications Frequency Power Transformer Input Output Part Number Replacement Battery Nominal Battery Life Current Draw Transmitted Indications Certification RE663 Wall Dimensions Table Top Footprint Weight Mounting Fasteners Pilot Hole for Screw into Wood Pilot Hole for Wall Anchor 3.81 x 5.10 x 1.55 inches (9.68 x 12.94 x 3.94 cm) 3.81 x 5.47 x 3.17 inches (9.68 x 13.89 x 8.05 cm) 1.49 lb (675 g)

#6 screws & 2 wall anchors (included) 1/8 in (3 mm) 3/16 in (4.7 mm) 32 to 120F (0 to 49C) 85% relative humidity non-condensing 100-240VAC, 50/60Hz, 0.5A 12VDC, 1A RE012-6 4 AA batteries 1 year (Battery operation under normal use) 350mA (Maximum) Low Battery, Supervision, Tamper, AC Fail 2.4 GHz FCC, IC Specifications subject to change without notice. IC NOTICE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

(1) This device may not cause harmful interference.

(2) This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Alula could void the users authority to operate this equipment. FCC ID: U5X-RE663 Le prsent appareil est conforme aux cnr dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) Lappareil ne doit pas produire de brouillage, et

(2) Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC: 8310A-RE663 47-00012 REV A 2021-03-16 Tech Support Line (888) 88-ALULA (888) 882-5852 alula.com 01

Alula RE663 123456ABCDEF

- FCC ID: U5X-RE663 IC: 8310A-RE663 el Power Supply: 12VDC === 1A ee Made in Mexico Date: YYJJJ

+ 48-00668 Rev A FCC ID: USX-RE663 IC: 8310ARE663 Power Supply: 12VDC ~~ 1A Wade in Mexico Date: YJ 48-00668 Rov A GC 1D: USXRE663 IC: 6310A-RE663 1 Power Supply: 12VDC ~~ 1A 8 + -

jade in Mexico Date: YYJJJ 48-00668 Rev A

Alula RE663 123456ABCDEF

- FCC ID: U5X-RE663 IC: 8310A-RE663 el Power Supply: 12VDC === 1A ee Made in Mexico Date: YYJJJ

+ 48-00668 Rev A

= FCC ID: USXRE663 IC: 6310ARE663 Power Supply: 12VDC ~~ 1A Made in Mexico Date: YYJJJ 48-00668 Rev A

March 22, 2021 RE: Confidentiality Request for U5X-RE663 To Whom It May Concern:

Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent*1 Permanent Permanent Permanent Permanent Permanent*

Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual

*Note: ______(Insert Explanation as Necessary)______ Alula has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. 1 2

- The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be:

The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.

- Please refer to http://atcb.com/publicdocs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. Sincerely, By:

(Signature/Title3) Paul Saldin, Vice President

(Print name) 3

- Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.