L IN S TAL UI D E G 360 Degree PIR Motion Sensor 360 PIR Motion Sensor alarms when motion is sensed. It is a commercial battery-powered ceiling mount sensor with a 360 degree detection range. Features 360 detection range with 62 distinct detection zones Range up to 40 feet in diameter Selectable pulse count 2 or 4 Designed for commercial application 5 year warranty Enroll by placing the panel into wireless enrollment mode and tripping the sensors enrollment sequence. Interlogix , DSC, Qolsys and Cryptix variants can be enrolled by pulling the battery tab or by tampering the unit. Honeywell and 2GIG variants can be enrolled by tripping the unit three times (tamper or motion) or by holding the tamper down and powering the unit up by pulling the battery tab. Honeywell and 2GIG sensors must be enrolled as a Loop1 sensor. Alternatively, all variants of the motion sensor can be enrolled by entering its serial number into the panel. Install by screwing two #8 screws into the ceiling, leaving 1/4 inch of thread exposed. Next, slide the back plate over the screws and rotate the back plate. Screw the third #8 screw through the wall tamper into the ceiling, ensuring that the wall tamper screw is attached to something solid. Tighten all screws until snug. Then, insert the square nut into the square slit of the cover and start threading the #4 screw into the side of the cover. Close the cover and conduct a walk test. After walk testing, take the unit out of walk test mode and close the cover again. Finally, finish threading the #4 screw until it is snug. Mounting Tips Avoid direct sunlight Avoid facing directly to AC or heating vents Avoid vapor or high humidity Avoid curtains, screens, etc. from blocking detection Do not install outdoors Use your panels installation guide to verify proper system setup. I Sensor functions Alarm LED can be switched either ON or OFF. Pulse Count can be switched to either 2 or 4 mode depending on the environmental conditions of the installation. Pulse Count Select 2 for normal applications. Select 4 for use in areas where there may be movement by small animals or other objects, such as fax machines or curtains. Walk Test Switch LED lights up when the unit has detected motion. An alarm signal is outputted whenever detection occurs. Normal Operation (Battery Saving Mode) LED lights up when the unit has detected if LED ON is selected. Once alarm is outputted, it does not output alarm again for 2 minutes. It goes back after 2 minutes and outputs alarm again when receiving detection signal. Detection Range Troubleshooting Problem Probable Cause Remedy Alarm is not activated although someone is walking in detection area Detection area is improper, battery is dead, Walk Test switch is OFF and 2 minute delay is active Conduct a walk test, change the battery Alarm is activated with nobody in the area LED does not light up at the time of the walk test Moving object within detection area, temperature of object within area is changing rapidly Remove the object from the detection area, remove the heat sources from the detection area or relocate the detector Walk test switch is OFF, battery is dead Turn the walk test switch ON, change the battery LED does not light up in normal operation LED switch is OFF, battery is dead Turn LED switch ON, change battery Pro Tips Save battery life by taking unit out of walk test mode after completing walk test. There is no 2 minute delay when in walk test mode. Leaving in walk test mode will severely decrease battery unit life. Light changes will cause the sensor to trip. Ensure that the detector is not placed near windows. Sudden temperature changes will cause the sensor to trip. Ensure the motion detector is not placed near heating and cooling vents. High humidity environments can cause condensation of the detection lens. Ensure the motion detector is not installed in these kinds of environments. Protective film should be removed from the lens after installation. Sensor Specifications: The table below displays the functional frequencies of each compatible sensor. Part Number Frequency Compatible RE159 319.5 Interlogix/Qolsys RE259 RE259T RE359 RE659 345 345 433 433 Honeywell 2GIG DSC Cryptix Specifications Physical Housing Dimensions Weight with Battery Mounting Fasteners Environmental 4.72 x 1.57 inches (40 x 120 mm) 4.2oz (120g)
(3) #8 screws, (1) square nut, (1) #4 screw (All provided) Operating Temperature Maximum Humidity 32F to 120F (0C to 49C) 85% non-condensing relative humidity Sensor Specifications Frequencies Replacement Battery Nominal Battery Life Battery Voltage Current Draw Detection Length Detectable Speed Transmitted Indications Certification RE159, RE259, RE259T, RE359, RE659 433.92 MHz, 319.5 MHz, 345 MHz One Panasonic CR123A Lithium Battery 3 years (assuming 720 trips/day), 7 years (assuming 240 trips/
day) 3.3 VDC (Nominal), 2.4 VDC (Low) 21 mA (Maximum), 4.7 uA (Standby), 30 mA (Max in walk test) Default: 16.5 feet (5m), Optional: 6.5 feet (2m) 1 to 5 feet per second (0.3 to 1.5 meters per second)Motion, Tamper (Cover/Wall), Low Battery, Supervision UL639, ULC-S306-03, ETL, FCC, IC Specifications subject to change without notice WARRANTY Resolution Products, Inc. will replace all non-portable products that are defective in their first five (5) years, and all portable products that are defective in their first two (2) years. IC NOTICE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux cnr dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
(1) Lappareil ne doit pas produire de brouillage, et
(2) Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC: 8310A-RE159, 8310A-RE259, 8310A-RE359 FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Resolution Products, Inc. could void the users authority to operate this equipment. FCC ID: U5X-RE159, U5X-RE259, U5X-RE359 TRADEMARKS INTERLOGIX, HONEYWELL, 2GIG, QOLSYS, AND DSC ARE TRADEMARKS OWNED BY UNITED TECHNOLOGIES ELECTRONIC CONTROLS INC., HONEYWELL INTERNATIONAL INC., TYCO SAFETY PRODUCTS CANADA LTD, QOLSYS INC. AND NORTEK SECURITY & CONTROL LLC, RESPECTIVELY. RESOLUTION PRODUCTS, INC. PRODUCTS WILL FUNCTION WITH ONE OF EITHER INTERLOGIX (FORMERLY GE), HONEYWELL, DSC, OR 2GIG SYSTEMS. HOWEVER, NO RESOLUTION PRODUCT IS PRODUCED BY, ENDORSED BY, NOR IS OFFICIALLY ASSOCIATED WITH INTERLOGIX (FORMERLY GE), HONEYWELL, DSC OR 2GIG. RESOLUTION RECOMMENDS VERIFYING PROPER ENROLLMENT AND OPERATION, PER CONTROL PANEL INSTALLATION INSTRUCTIONS, AT INSTALLATION. 47-0047-00 RevA 2018-01-18 Tech Support Line (877) 260-5578 www.ResolutionProducts.com