RE636 Wireless Outdoor Siren Strobe Connect+ Encrypted The RE636 Wireless Outdoor Siren Strobe is an auditory warning device that produces high volume warning sounds and visual strobing. L IN S TAL UI D E G Features Multi-cadence siren 100 dBA minimum at 1m 2-5 year battery life (batteries included) or AC powered
(RE012-17 sold separately) 5-year warranty Sounds a high volume warning for burglary, smoke and carbon monoxide alarm conditions. Volume is adjustable through the Connect+ Installer application, or through the interactive service providers web portal. Enroll by placing the panel and siren into wireless enrollment mode. The sirens PWR and RF LEDs will blink back and forth when in enrollment mode. If the siren has never been enrolled, enrollment mode will start automatically when opening the cover. To overwrite a previously enrolled ID, power up the device while holding the tamper. When the red RF LED illuminates, release the tamper switch. After enrolling the siren, take the panel out of wireless enrollment mode. Mounting Holes Once the siren is properly enrolled, test functionality in a desired location. The panel supports up to eight RE636 sirens at one time. Replace batteries by opening the cover and removing the inner cover to gain access to the 3 C-cell batteries. To remove inner cover, push down the two latches, then pull out the clear inner cover. Mounting can be done by securing the siren to a surface with the mounting screws (included) at the three slotted mounting holes. Ensure arrows inside are pointed up. Pro Tips Cover can hang from bottom of enclosure and inner cover can clip into cover for convenience while work is being done inside enclosure. To change the strobe lens, unscrew the cover screw until it is past the lens, and then push on the corner of the lens to loosen and remove. Select desired color. Inner cover removal latches Power (PWR) LED will turn on when the siren is awake (every 18 seconds on battery and always when powered from wall). RF LED will blink when a packet is received. Enroll packets are automatically sent every 18 seconds when in enroll mode. Pressing or releasing the tamper switch while sensor is in enroll mode will send another enroll packet. Use the panel installation guide to verify proper system setup. I Specifications Physical Housing Dimensions Weight with Batteries Mounting Hardware Environmental Operating Temperature Maximum Humidity Sensor Specifications 12.0 x 11.2 x 2.2 inches (30.5 x 28.4 x 5.6 centimeters) 2.6 pounds (41.6 ounces) 3 Stainless Steel Mounting Screws 0F to 130F (-18C to 55C) 85% non-condensing relative humidity Frequency Replacement Battery Battery Life Battery Voltage Current Draw Sounder Loudness Wall Connection (Optional) Transmitted Indications 433 MHz 3 Energizer C-Cell Batteries 2-5 years, non rechargeable 4.5 VDC (nominal) 4uA (Sleep), 16mA (AC Power), 1.05A (Alarm) 100 dBA, minimum at 1m US 2-prong electrical outlet blades (RE012-17) Low Battery, Supervisions, Cover Tamper, Wall Tamper Certification RE636 FCC, IC AC/NZS 60950-1:2015 ETSI EN 300 220-2 V2.4.1 / AS/NZS 4268:2012 ETSI EN 301 489-1 V1.9.2 ETSI EN 301 489-3 V1.6.1 Specifications subject to change without notice WARRANTY Alula will replace all non-portable products that are defective in their first five (5) years, and all portable products that are defective in their first two (2) years. IC NOTICE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux cnr dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
(1) Lappareil ne doit pas produire de brouillage, et
(2) Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC: 8310A-RE636 FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Alula could void the users authority to operate this equipment. FCC ID: U5X-RE636 TRADEMARKS Alula and Connect+ are trademarks owned by Alula Holdings, LLC. Energizer is a registered trademark owned by Energizer Brands, LLC. 47-0063-00 REV A 2019-05-30 Tech Support Line (888) 88-ALULA (888) 882-5852 alula.net 02