FCC ID: 2AHCYRGBCCT-RMT RF Remote

System Parts:

(1) Dynamic RF LED Remote Control . . . . . . . . . . . . . . . P/N: L-RGBCCT-RMT

(1) Dynamic RF LED Parent Controller . . . . . . . . . . . . . . P/N: L-RGBCCT1-PREC

(1) Dynamic RF LED Child Receiver (optional) . . . . . . . . P/N: L-RGBCCT1-CREC

(1) Power Supply, Class 2, 12VDC 60W max (or) 24VDC 96W max Tresco low voltage 12VDC or 24VDC LED RGB or CCT light(s) with Starter Cord Instructions FREEDiM Dynamic RF Remote Control For RGB & CCT LEDs 12VDC 60W & 24VDC 96W The FREEDiM Remote Control starts out with preset settings:

RGB preset - all values start at 0-0-0 CCT preset - begins at 2700K RGB CCT Remote Control Remote Control Specifications:

L-RGBCCT-RMT Operating Voltage: . . . . . . . . . . . . . . . . (2) AAA batteries (included) Radio Frequency: . . . . . . . . . . . . . 916 .5 MHz RF Remote Distance: . . . . . . . . . . 66 ft . (20m)

#1 Home Button Takes any settings back to Start

(Starts over at preset settings, but does not erase pairing) R Speed-up Button Increases the speed of whatever RGB program running G B Z1 Play Button Starts the pre-set programs . Hit play again stops that program . Hit play again moves to the next program . R 3000K 3500K 5000K Z2 3000K 3500K 5000K G B B Z2 R G Z1 3000K 3500K 5000K Speed-down Button G R R Decreases the speed of whatever Z1 RGB program running G R 3500K 3000K 3000K B G B Z2 B 3500K 5000K 5000K Zone 1 & Zone 2 Buttons 3000K Z1 3500K Z1 5000K Z2 Z2 Switches between Zones 1 and 2 for independent zone functions Z1 Z2 On Indicator Light CCT Slider for CCT control

(slide with finger touch) RGB Color Wheel for RGB control

(rotate with finger touch) On/Off Button Dim Button Dims up or down R 3000K G 3500K B 5000K Z1 Z2 R G B 3000K Z1 R R R 3500K 3000K 3000K 3000K R R R Z1 Z1 Z1 B B G G G 5000K RGB Buttons B Quick preset buttons 3500K 3500K 5000K In RGB mode, quickly go to Z2 preset Red, Green or Blue colors G 5000K 3500K 5000K G G B B B Z2 Z2 Z2 3000K 3000K 3000K 3500K R Z1 G Z1 Z1 3500K 3500K 5000K CCT Buttons 5000K 5000K Quick preset buttons Z2 In CCT mode, quickly go to preset Warm (3000K), Neutral (3500K), or Cool (5000K) light Z2 Z2 B 3000K 3500K 5000K Z1 Z2 Switch Mode Switches unit between RGB and CCT modes Zone 1 Indicator Light RGB Indicator Light Zone 2 Indicator Light RGB and CCT full-function controls:

The Tresco FREEDiM Remote Control provides color and brightness controls for RGB or CCT (white color-tunable) lighting on Tresco low voltage LED RGB and CCT lights . It also controls the intensity (dim levels) of the lights up to 95% . The digital screen on the FREEDiM Parent Controller displays the current mode and settings . The wireless Remote Control must be positioned within 66 ft .

(20m) of Parent Controller and any Child Receivers . Note: outside interference may affect the signal between Remote Control and Parent Controller . (see Signal Interference on page 2) RGB and CCT modes:

Prior to installation you need to select between RGB or CCT LED lights . Then after installation, you must select either RGB or CCT mode on the Parent Controller . (see the Switch Mode button above, in Fig 1) See separate instruction sheets for further information on Tresco low voltage LED RGB and CCT lights, FREEDiM Parent Controllers and Child Receivers, and Power Supplies. Pairing the Remote Control to the Parent Controller 1 . First install the Parent Controller with either a RGB or CCT LED light system and then turn on the Parent Controller . 2 . Check the mode on the Parent Controller and select either RGB or CCT mode depending on the LED light system installed . 3 . On the Remote Control hit the ON button

- The small indicator light in top corner is now red, indicating that the Remote Control is live and active (this light stays on for 30 sec .) (see Fig. 1 above) . 3000K 3500K 5000K G R B R G B 4 . Using the Switch Mode button Z1

, select either RGB or CCT mode . The red 3000K 3500K 5000K Z2 indicator light underneath the Switch Mode button indicates RGB mode . Z1 Z2 R G B 5 . On the Parent Controller press the Learning Key one time . 3000K 3500K 5000K 6 . Next on the Remote Control press the Zone 1 button light underneath is now red (see Fig. 1 above) . Z1

. The Zone 1 indicator Z2 7 . After you have hit the Zone 1 button, touch either the RGB Color Wheel or CCT Slider . Lights will flash once indicating everything is paired . Then repeat steps if adding Zone 2 or more Parent Controllers . Note: Each zone can control 1 Parent Controller and up to 10 Child Receivers . Each zone is independent and must be controlled separately from each other .(see more information and illustration on page 2)

(Instructions continued on page 2) Instructions FREEDiM Dynamic RF Remote Control For RGB & CCT LEDs 12VDC 60W & 24VDC 96W Page 2 To Deprogram the Remote Control:

1 . Press and hold the Learning button on the Parent Controller . This will erase all programming on the Remote Controls .

(Note: you cannot erase just one Remote Control at a time .) Additional Information on Button Functions:

10 Pre-programmed, RGB Color-Changing Modes:

Parent Controllers are pre-loaded with ten different programs to quickly change lighting specifications when needed . The ten programs are for the RGB mode only and include: RGB color mixes, flashing, fade-in/

fade-out, etc . These pre-loaded programs are only accessible through the Remote Control . CCT Slider and RGB Color Wheel

In CCT mode, you can quickly make adjustments with the CCT Slider on top of the unit .

In RGB mode, you can quickly make adjustments with the large RGB Color Wheel .

- The RGB Color Wheel will not work in CCT mode, and the CCT Slider will not work in RGB mode . To Access and Review the 10 Pre-programmed Modes:

1 . On the Remote Control (in RGB mode), press the Play button once to play the first Preset Mode (see list below) . Press the Play button again to stop it . Press the Play button once again to advance to the next preset mode . 3000K 3500K 5000K G B R Z1 Z2 2 . Press the Speed-up button faster fade-in/fade-out) . R G B to increase the speed of the mode (e .g . To check current settings, view the Parent Controllers digital screen . 3 . Press the Speed-down button to decrease the speed . 3000K 3500K 5000K

- The Remote Control cannot control both zones at once . Each zone must Mode 9: R&B two colors mix fade (R in B out), then G fade-in, then R&B RGB and CCT Quick Preset Buttons:

The RGB/CCT Preset buttons are dual-purpose:

In RGB mode, the (3) Preset buttons quickly go to preset Red, Green or Blue colors . Then the buttons work by turning on/off R, G or B . For example, press R if you want solid red . Press R again to turn red off . If you then want a mix of red and blue, press R and B . In CCT mode, the (3) Preset buttons quickly go to preset Warm (3000K), Neutral (3500K), or Cool (5000K) light . As in RGB mode, turn on/off the Quick Preset buttons to achieve other warm/cool lighting effects . Zone 1 and Zone 2 Buttons

- The FREEDiM Remote Control can control up to 2 zones independently .

(also see Fig. 2 below) be controlled independently .

- The Remote Control can have one zone in RGB mode and the other zone in CCT mode to control two different Parent Controllers, but any single Parent Controller can only be in RGB or CCT mode .

- To turn off a zone press and hold either the Zone 1 or Zone 2 button . Switch Mode Button

- When the Remote Control is in RGB mode, the small indicator light 3000K 3500K 5000K G B R under the Switch Mode button Z1 Z2 is red (see Fig. 1, on page 1) .

- When in CCT mode, there is no indicator light .

#2 Each Remote Control can control up to 2 Parent Controllers 1 2 Note: Each zone can handle 1 Parent Controller and up to 10 Child Receivers . IMPORTANT SAFETY INSTRUCTIONS Use only in dry locations . Not for use where exposed to the weather . Replace the batteries on the Remote Control with (2) AAA batteries only (non-rechargeable) . Clean with a damp cloth . Do not use cleaners or detergents . I-RGBCCTRMT-0720 R Z1 G B Z2 3000K 3500K 5000K The Built-In 10 Color-changing Modes are as follows:

Z2 Z1 Mode 1: Randomly selects any two colors of RGB mix fade-in & fade-out Mode 2: RGB three colors mix fade-in & fade-out Mode 3: RGB three colors mix fade-out & fade-in Mode 4: RGB flash Mode 5: RGB three colors fade-in & fade-out successively Mode 6: RGB three colors fade-in successively Mode 7: RGB three colors fade-out successively Mode 8: RGB three colors jump changing successively mix fade (R out B in), then G fade-out Mode 10: B fade-out, then G&B mix fade (G out B in), then R&G mix fade

(R out G in), then R fade-in Signal Interference:

Outside interference may affect the signal between the Remote Control and Parent Controller or Child Receiver . Typical items that might cause interference include: metal pots and pans, leaded glass, aluminum framed doors, etc . If experiencing interference, try repositioning the Parent Controller or Child Receiver in 6 (15cm) increments . This typically allows the system to function properly . Save these instructions for future reference. For technical assistance, call 1-800-227-1171 Tresco Lighting by Rev-A-Shelf 12400 Earl Jones Way Louisville, KY 40299 Tel: 800-227-1171 Fax: 502-491-2215 Email: cservice@trescolighting .com Web: www .trescolighting .com RoHS COMPLIANT FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

DATE : 2020-08-31 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Actas Agent On our behalf, | appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission's regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Rev-A-Shelf and 12400 Earl Jones Way Louisville, Kentucky 40299, United States Signature:

Yea Name: Chris Tress Title: Director Company: Rev-A-Shelf

Rev-A-Shelf DATE : 2020-08-31 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AHCYRGBCCT-RMT Product Name: RF Remote Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ...) e Schematics e Block diagram e Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature:

Name: Chris Tress Title: Director Company: Rev-A-Shelf