FCC ID: 2AHCYRGBCCT RF Wall Switch

System Parts:

(1) Wall Controller - RGB . P/N: L-WLD-RGB-WH-1

(1) Wall Controller - Color Tunable White . P/N: L-WLD-CCT-WH-1

(1) Dynamic Parent Controller (12/24VDC) (required) . P/N: L-RGBCCT1-PREC

(1) Dynamic RF LED Child Receiver (12/24VDC) (optional) . P/N: L-RGBCCT1-CREC

(1) Power Supply, Class 2, 12VDC 60W max (or) 24VDC 96W max Tresco low voltage 12VDC or 24VDC LED RGB or CCT light(s) with Starter Cord Also see Accessories below. Installation Instructions FREEDiM Wireless RGB & CCT Wall Controllers FreeDim RGB/CCT Wall Controllers (AARAS) < upd 1020m Single Zone 12VDC 60W & 24VDC 96W Wall Controller Specifications:

Operating Voltage: . (1) CR1620 battery (included) Radio Frequency: . 916.5 MHz RF Remote Distance: . 50 ft. (15m) Parent Controller & Child Receiver Specifications:

Input Voltage: . 12VDC or 24VDC Output: . 12VDC (5A, 60W), or 24VDC (4A, 96W) Front views R

#1 RGB Wall Controller CCT Wall Controller Mounting Cradle READ ALL INSTRUCTIONS BEFORE INSTALLING SYSTEM. Before beginning installation, be sure power is turned OFF to light system. Front views Index Tab to orient Controller 2 61mm 4 103mm G B 1 27mm FreeDim Wall Controller (AARAS) < upd 1020 m W C 1 27mm Housing 1 33mm Tresco FREEDiM Wall Controllers provide color control for RGB lighting or warm/

cool controls for CCT (white color-tunable) lighting on Tresco low voltage LED RGB and CCT lights. They also control the intensity (dim levels) of the lights. The digital screen on the FREEDiM Parent Controller displays the current mode and settings. The wireless Wall Controller must be positioned within 50 ft. (15m) of the Parent Controller. Note: outside interference may affect the signal between Wall Controller and Parent Controller or Child Receiver. (see Signal Interference on page 2) The Wall Controller's mounting cradle (see Figure 1) allows installation directly to drywall or to a standard wall electrical box, giving the appearance of a hardwired wall switch. Verify power to outlet box is off before installing. (see Figure 2 for installation options) The Wall Controller has a magnet to hold it within the mounting cradle or to place on any magnetic surface (i.e. refrigerator door). To remove Wall Controller from mounting cradle use the slight indents on the top and bottom edges of Controller. The mounting cradle has an index tab to orient the Wall Controller in the proper

"up" position. (see Figure 1) Trescos FREEDiM Parent Controllers and Child Receivers can be used with any Class 2, 12VDC/60W or 24VDC/96W Power Supply. As an option, Tresco Power Supplies are available: (see Power Supplies on Figure 3 & 4) For more Power Supply options, see Tresco Specifications Catalog. 12VDC/60W max. part no.: L-DC-SLELT60-1, and 24VDC/96W max. part no.: L-24DCELT96-1 Installing Parent Controller:

NOTE: All wiring must follow local codes and NEC regulations. 1. Verify power is turned off to light system. Connect Parent Controller input wire to 12VDC or 24VDC Power Supply output wire (see Figures 3 & 4). 2. If using Tresco Power Supplies, connect Parent Controller input wire to 12VDC Mounting Block or 24VDC 5-Output Barrel Splice (see Figures 3 & 4). Otherwise follow installation guide of power supply used. To use multiple Parent Controllers or Child Receivers on one Power Supply, the optional 12VDC Mounting Block (P/N: L-TRANS-MNT-BL) can accept 6 Parent Controllers and/or Child Receivers. The optional 24VDC 5-Output Barrel Splice

(P/N: L-1BRL5-1) can accept 5 Parent Controllers and/or Child Receivers. Use insulated staples or plastic ties to secure ALL loose cords. 3. With RGB or CCT light(s) connected to a starter cord, plug the starter cord into the Parent Controller or Child Receiver(s) 4-Position Amp Output Connector. Child Receivers must be used with Parent Controller. To connect multiple RGB or CCT light(s) to a single Parent Controller or Child Receiver use the optional 4-Position 6-Output Adaptor Cord (P/N: L-4P6O-1). Plug the input wire of the Adaptor Cord to the 4-Position Amp Connector on the output of the Parent Controller or Child Receiver. Then plug the desired RGB or CCT light(s) starter cords into any of the 6 outputs of the Adaptor Cord. The 4-Position 6-Output Adaptor Cord works with 12VDC/5A and 24VDC/4A systems as well as RGB and Color Tunable White Lights. 4. Check all connections and turn on power to the Power Supply. 5. Check the mode on the Parent Controller and select either RGB or CCT mode depending on the LED light system installed. NOTE: See separate instruction sheets for further information on Tresco low voltage LED RGB and CCT lights, FREEDiM Parent Controllers and Child Receivers, and Tresco Power Supplies. See page 2 for further instructions. Accessories (sold separately): Extension and Link Cords, additional Parent Controllers, Child Receivers, Wall Controllers, 12V Mounting Blocks, 24V 5-Output Barrel Splices, 4-Position 6-Output Adaptor Cords. Side views Side views 13mm 13mm

#2 Options to Install Mounting Cradle in a Wall Option 1:

Non-Metallic Low-Voltage Bracket

(e.g. Carlon Model #SC100R) FreeDim Wall Controller (AARAS) < upd 1020 m Option 3:

Option 2:

Single Outlet Box Multiple Outlet Box Cover with a Decora style wall plate Orig IN IN PDF from RAS 116 called I-WLDIM1RND WATCH! old lines have double-lines w layers. See Hidden Layer for orig IL. >

GRX flip & rework middle IL only on 1217 MP ... But since converted to G5 !!! 218 (u.519, 619) RF LED Controller RF LED Receiver

#3 Typical 12V Installation Showing example of CCT 3-Wire installation with optional Tresco products Tresco 12V LED lights

(example using CCT FlexTape) 4-Position AMP Connectors 4-Position 6-Output Adaptor Cord

(optional) CCT Tape Connector Input Cord 6 (152 mm) Parent Controller Power Supply 12 VDC 60W Orig IN IN PDF from RAS 116 called I-WLDIM1RND WATCH! old lines have double-lines w layers. See Hidden Layer for orig IL. >

GRX flip & rework middle IL only on 1217 MP ... But since converted to G5 !!! 218 (u.519, 619) OUTPUT 12 VDC 12V Mounting Block

(optional) Length w/wire 9-5/16 (236 mm) Child Receiver (optional) RF LED Controller RF LED Receiver Learning Key CCT Adaptor Cord

(3-wires) (2 50mm) CCT Starter Cord

(3-wires)

#4 Typical 24V Installation Showing example of RGB 4-Wire installation with optional Tresco products Tresco 24V LED lights

(example using RGB FlexTape) Barrel-to-AMP Adaptor Cord

(optional) 3 (76mm) Input Cord 6 (152 mm) Parent Controller LED Power Supply 12 VDC Install Wall Dimmer on input (line voltage) side of Power Supply OUTPUT 12 VDC 4-Position 6-Output Adaptor Cord

(optional) 4-Position AMP Connectors INPUT RGB Tape Connector Power Supply 24 VDC 96W Child Receiver (optional) 24V 5-Output Barrel Splice

(optional) Length w/wires 13 (330 mm) Learning Key RGB Adaptor Cord

(4-wires) (2 50mm) RGB Starter Cord

(4-wires) Installation Instructions FREEDiM Wireless RGB & CCT Wall Controllers Single Zone 12VDC 60W & 24VDC 96W FreeDim RGB/CCT Wall Controllers

(AARAS) < upd 1020m Page 2 Programming Instructions:

NOTE: Each Wall Controller will only pair with ONE Parent Controller. Wall Controllers do not pair with Child Receivers. 1. Remove the Wall Controller from the Mounting Cradle (Figure 1 on page 1). Remove the clear plastic tab to activate the battery. 2. Press once (do not hold down) the Learning Key (see Figures 3 or 4 on page 1) on the Parent Controller, then press "On" once on the Wall Controller (see Figure 5). The Parent Controller connected light should flash on/off, indicating they are paired up and programmed properly. 3. Repeat Step 2 for any additional Controllers to pair up. NOTE: Each Wall Controller can control 1 Parent Controller. Each Parent Controller can be paired with up to 10 different Child Receivers (see Figure #6). Deprogramming:

1. To deprogram, press and hold down the Learning Key on the Parent Controller until the lights flash. Wall Controller. 2. The Parent Controller is now reset and no longer paired to the To Control the Lights:

RGB Wall Controller:

To turn on and off, press the "On/Off" button once (see Figure 5). Press R, G or B buttons once to increase the value of that color. Press R, G or B buttons a second time to decrease the value of that color. To dim or brighten the lights once the colors are set, hold down the "On/Off"

button. To dim/brighten the lights in the opposite direction, hold down the "On/

Off" button a second time. The lights dim from 100% down to 5%. CCT Wall Controller:

(see Figure 5). To turn on, press the "On" button once. To turn off, press the "Off" button once the On button. The lights dim from 100% down to 5%. NOTE: To check current settings, view the Parent Controllers digital screen (see Figure 6). Each Parent Controller can control up to 10 Child Receivers

#6 99 9 88 8 1010 10 77 7 11 1 66 6 22 2 55 5 33 3 44 4

#5 RGB Wall Controller CCT Wall Controller R Red increase &

decrease red color intensity On/Off

(press), dimming

(hold) On turn on, or adjust intensity W Warm adjust light warmer white Green increase &

decrease green color intensity G B Blue increase &

decrease blue color intensity Off turn off, or adjust intensity C Cool adjust light cooler white Signal Interference:

Outside interference may affect the signal between the Wall Controller and Parent Controller or Child Receiver. Typical items that might cause interference include: metal pots and pans, leaded glass, aluminum framed doors, etc. If experiencing interference, try repositioning the Parent Controller or Child Receiver in 6 (15cm) increments. This typically allows the system to function properly. IMPORTANT SAFETY INSTRUCTIONS CAUTION: To reduce the risk of fire, electric shock, or injury to persons:

Use proper Class 2, Power Supply for the lighting system e.g. 12VDC Power Supply with 12V Lights; and 24VDC Power Supply with 24V Lights. Parent Controller output 12VDC 60W 5A max or 24VDC 96W 4A max NOT intended for use in ceilings, soffits or walls. Use only in dry locations. Not for use where exposed to the weather. Do not run line voltage power supply cord through holes in walls, ceilings, floors or similar permanent structure. If required, a licensed electrician should be consulted for wiring through permanent structures. When mounting and wiring light system, follow all local electric codes and the National Electrical Code

(NEC). Disconnect electrical power before cutting light or modifying system. Save these instructions for future reference. For technical assistance, call 1-800-227-1171 Tresco Lighting by Rev-A-Shelf 12400 Earl Jones Way Louisville, KY 40299 Tel: 800-227-1171 Fax: 502-491-2215 Email: cservice@trescolighting.com Web: www.trescolighting.com I-WLDCCTRGB 1120 Press W to adjust the color temperature of the lights warmer. Use only insulated staples or plastic ties to secure cords. Press C to adjust the color temperature of the lights cooler. Route and secure cords so that they will not be pinched or damaged To dim the lights, hold down the Off button. To brighten the lights hold down when the cabinet is pushed to the wall. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Rev-A-Shelf Agent Authorization Company: Rev-A-Shelf Address: 12400 Earl Jones Way Louisville, Kentucky 40299, United States Product Name: RF Wall Switch Model Number(s): WLD-RGB-WH, WLD-CCT-WH Product Description: RF Wall Switch We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2020-09-08 Name:

Chris Tress Title:

Director Company: Rev-A-Shelf

Rev-A-Shelf Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Date: 2020-09-08 Subject; Request for Long Term Confidentiality FCC ID: 2AHCYRGBCCT To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Chris Tress Title: Director

Differences Declaration To whom concern, We company Rev-A-Shelf hereby declares: The product models WLD-RGB-WH, WLD-CCT-WH are identical in the same PCB layout, interior structure and electrical circuits, the only difference is the model name for commercial purpose. Authorized signature:

Name: Chris Tress Date: 2020-09-08