External Components Introduction Turn on Device Start measuring This device is able to calculate your heart The device will turn on after pressing the Press the recording button when the device rate, heart conditions, stress and nervous power button for 2 seconds. The power LED is solid on your chest. The device will beep index. Provide instant health information will light up and the Transferring LED will once. After several seconds, the device for you. Contents blink slowly in standby mode. beeps constantly for a good signal Before measuring device x1 Charger cable x1 Put the device to your chest. The 4 Instruction(this page) x1 conductors should contact your body solid. 1 Charge connector 6 Recording LED Before using 2 Conductors 7 Recording Button Please charge the device with the USB cable 3 Power button 8 Power LED for 3 hours. The charging LED will turn on 4 Cable connector 9 Transferring LED when charging and turn off after the 5 Charging LED Download APP Find the QR code below for APP download Android iOS battery is full. Attention: you may not operate the device when charging. Data uploading 1. Explore the Cmate Gen2 APP 2. Point at [file uploading] button and select the file for analysis by recording time. 3. Wait until server responds the result. If it shows poor signal please take another measurement and upload again. 4. All result will stay in the [my report page]. The latest analysis result will show on the main page of the APP. Bluetooth Pairing Android user need to paring the device first. 1. Turn on the device (standby mode). 2. Explore Bluetooth settings in your phone. 3. Scan the nearby Bluetooth device, find CmateH device and finish the pairing recorded. After 30 seconds, the device beeps twice for end recording and turns into standby mode. If you need terminate the measurement, press the recording button again and the device will turn into standby mode. You can utilize the Cmate Gen2 APP for data analysis service. Please also put on some cream on your chest and conductors before measuring. Power Management The device will automatically turn off after 3 minutes standby for the sake of power saving. You may push the power button for 2 seconds for manual turn off. When the battery is low, the device will beep once by every 5 seconds. The Power LED also blinks every second. The device is still workable yet we advise you to charge the device immediately. When the battery is extreme low, the device will shut down automatically. Please charge the device for 3 hours immediately. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Non-modification Statement:
Changes or modifications not expressly approved by the party responsible for Error Messages LED fast blinks and beeps twice every seconds Device memory full, please upload or delete the file with APP. If the error still occur, please contact your sales channel for further help please contact your sales channel for further help The device is not able to charge Brand Name:Cmate Model:CHI-100
( 1214 )
---
---
Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction. Revlis Biotech Co., Ltd. 7F., No 108-1, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, Tel : +886-2-22198878 FAX : +886-2-22192587