FCC ID: M9MF80100 Dual Frequency RFID Reader

01/20/2020 To Whom it may concern OEM Responsibilities to comply with FCC and Industry Canada Regulations The OEM integrator must be aware not to change any RF related parameters or provide information to the end user regarding how to modify this OEM RF module or change RF related parameters in the end product or all warranty or certifications will be VOID. OEM End Product Labeling requirements The OEM-805N11KU, OEM-805N21KU, OEM-805N11K5 and OEM-805N11K7 modules are labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Numbers are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:

Contains Transmitter Module FCC ID: M9MF80100 Contains Transmitter Module IC: 6571A-F80100 The above OEM modules have been certified for integration into products only by OEM integrators under the following condition:

The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone (866) 439-4884 toll free (847) 483-1129 fax Sales@RFIDeas.com www.RFIDeas.com

WAVE ID Plus Reader QUICK START GUIDE This document provides the following information:

I. Connector Options II. Installing the Configuration Utility Software III. Reader Setup IV. Configuring the Reader V. Troubleshooting Wave ID pcProx Plus Reader Congratulations on the purchase of your pcProx or pcProx Plus reader!

Configuration of RF IDeas readers is easy. With our plug and play design, you will be able to quickly take advantage of a more secure environment in your business, school, or organization. RF IDeas products are an integral part of a variety of solutions in every market such as healthcare, manufacturing, government, enterprise and other markets. The number of applications is ever-increasing and we maintain a strong relationship with our robust list of software partners and resellers which are readily found on our website. Please contact our Sales department if you have any questions or are interested in our OEM and Independent Developers programs. For more details about our product line, please visit www.RFIDeas.com/knowledge-center or follow the Support > Learning Center link for more details about our various products. Thank you, The RF IDeas team CONTACT INFORMATION Phone: +1 (847) 870-1723 Toll Free: (866) 439-4884 Fax: (847) 483-1129 Email: Sales@RFIDeas.com Support: TechSupport@RFIDeas.com ADDRESS RF IDeas, Inc. 4020 Winnetka Avenue Rolling Meadows, IL 60008, USA 2 1. Connector Options There are two connector options available with the reader for data input and output. Connector Type Output Data Type USB Keystroke SDK Virtual Com Port: ASCII or SDK USB DB9 ASCII SDK The product you have purchased may need to be configured before use. The configuration software and support documents can be downloaded from our product support page at:

http://www.rfideas.com/support/product-support The configuration section details the steps necessary to install the configuration utility software and update the configuration to meet your requirements. 2. Installing the Configuration Utility Software To install the configuration utility software, complete the following steps:

1. Verify the system meets the following minimum requirements:

Hardware Pentium class PC Memory 32 MB RAM Disk 25 MB hard disk space I/O 1 available DB9 or USB port, dependent upon the connector Operating System Any operating system that supports a USB keyboard including Microsoft Windows XP, 7, 8, 10 and Linux. Can be used for keystroke applications. 2. Install the pcProx Configuration Utility from the following Web page:

http://www.RFIDeas.com/Software/pcProxConfig/

3. Reader Setup To set up the reader:

3. Plug the connector into the workstations (or available on any peripheral) open RS-232, USB, or Ethernet plug. 4. Place the device next to the monitor, beside the workstation, or where appropriate. 5. The workstation should detect new hardware for USB and DB9 connections. Verify the workstation recognizes this connection using Device Manager. 6. For RS-232 products, verify the correct COM port for RS-232 DB9 connections using Windows Device Manager. 4. Configuring the Reader To configure the Reader for operation, complete the following steps:

7. Start the pcProx Configuration Utility software. 8. Plug the reader into the workstations USB or DB9 port. a. If the reader has a USB connector, verify the workstation detected the connection automatically using Windows Device Manager. b. If the reader has a DB9 connector, verify the correct COM port using Windows Device Manager. 9. If your reader requires a custom configuration, refer to the pcProx Plus/pcProx Enroll Manual for detailed information on the configuring the reader. The manual is available at www.RFIDeas.com > Support >

Product Manuals. 10. After the configuration settings are correctly configured and written/saved to the device, unplug the reader. The reader is now ready for use. Troubleshooting If the device is not working or the following error message is displayed:

11. Check to be sure the device is connected to the USB or RS-232 port. When the workstation is on and no card is being read, the LED is red. A valid proximity card causes the LED to turn green, provided the configuration is not set to only read certain bit lengths. 12. Only one COM port application can own the RS-232 port at a time. Make sure there is not another COM port application running. This prevents our software from seeing the device. 13. Verify the correct model and the software configuration screen agrees with the device attached. 14. Verify the port agrees with the workstation connector. 15. If the device still does not work, disconnect it, remove General USB Device using Windows Control Panel a Add/Remove Hardware. Then reboot the workstation. When the workstation boots up, re-attach the device USB and the OS should re-install the Windows driver automatically. If the device does not read the card, contact the card manufacturer/vendor to verify that the card type is compatible with the device model. Radio Waves Reader Contactless Badge License Agreement and End-User License Agreement End-User License Agreement for RF IDeas SOFTWARE and HARDWARE - RF IDeas pcProx, Proximity Activated Readers, Software Developers Kit, and Proximity Reader DLLs, and Protocol(s). by a licensed end user in accordance with Section 1.1. A single license for the SOFTWARE PRODUCT may not be shared or used concurrently by other end users. IMPORTANT-READ CAREFULLY: This End-User License Agreement

(EULA) is a legal agreement between you (either an individual or a single entity) and the manufacturer RF IDeas (Manufacturer) with which you acquired the RF IDeas software and hardware product(s) identified above

(PRODUCT). The PRODUCT includes the RF IDeas reader, computer software, the associated media, any printed materials, and any on line or electronic documentation. The SOFTWARE PORTION OF THE PRODUCT includes the computer software, the associated media, any printed materials, and any on line or electronic documentation. By installing, copying or otherwise using the PRODUCT, you agree to be bound by the terms of this EULA. If you do not agree to the terms of this EULA, RF IDeas is unwilling to license the PRODUCT to you. In such event, you may not use or copy the SOFTWARE PORTION OF THE PRODUCT, and you should promptly contact the vendor you obtained this PRODUCT from for instructions on return of the unused product(s) for a refund. The products described in this publication are intended for consumer applications. RF IDeas assumes no liability for the performance of product. RF IDeas products are not suitable for use in life-support applications, biological hazard applications, nuclear control applications, or radioactive areas. None of these products or components, software or hardware, are intended for applications that provide life support or any critical function necessary for the support of protection of life, property or business interests. The user assumes responsibility for the use of any of these products in any such application. RF IDeas shall not be liable for losses due to failure of any of these products, or components of these products, beyond the RF IDeas commercial warranty, limited to the original purchase price. SOFTWARE PRODUCT LICENSE: The PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PORTION OF THE PRODUCT is licensed, not sold. 1. GRANT OF LICENSE. This EULA grants you the following rights:

*Software. You may install and use one copy of the SOFTWARE PORTION OF THE PRODUCT on the COMPUTER. *Network Services. If the SOFTWARE PORTION OF THE PRODUCT includes functionality that enables the COMPUTER to act as a network server, any number of computers or workstations may access or otherwise utilize the basic network services of that server. The basic network services are more fully described in the printed materials accompanying the SOFTWARE PORTION OF THE PRODUCT. *Storage/Network Use. You may also store or install a copy of the computer SOFTWARE PORTION OF THE PRODUCT on the COMPUTER to allow your other computers to use the SOFTWARE PORTION OF THE PRODUCT over an internal network, and distribute the SOFTWARE PORTION OF THE PRODUCT to your other computers over an internal network. 1.1 General License Grant. RF IDeas grants to an individual, a personal, nonexclusive license to make and use copies of the SOFTWARE PRODUCT for the sole purposes of designing, developing, and testing your software product(s) that are designed to operate in conjunction with any RF IDeas designed proximity reader product. You may install copies of the SOFTWARE PRODUCT on an unlimited number of computers provided that you are the only individual using the SOFTWARE PRODUCT. If you are an entity, RF IDeas grants the right to designate one individual within your organization to have the sole right to use the SOFTWARE PRODUCT in the manner provided above. 1.2 Documentation. This EULA grants an individual, a personal, nonexclusive license to make and use an unlimited number of copies of any documentation, provided that such copies shall be used only for personal purposes and are not to be republished or distributed (either in hard copy or electronic form) beyond the users premises and with the following exception: you may use documentation identified in the SOFTWARE PRODUCT as the file format specification for RF IDeas proximity readers solely in connection with your development of software product(s) or an integrated work or product suite whose components include one or more general purpose software products. 1.4 Sample Code. RF IDeas grants you the right to use and modify the source code version of those portions of the SOFTWARE PRODUCT identified as Samples in the SOFTWARE PRODUCT (Sample Code) for the sole purposes to design, develop, and test your software product(s), and to reproduce and distribute the Sample Code, along with any modifications thereof, only in object code form. 2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS. *Limitations on Reverse Engineering, De-compilation and Disassembly. You may not reverse engineer, decompile, or disassemble the PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation *You may not reproduce or otherwise emulate, in whole or in part, any form the protocol(s) defined within this PRODUCT for use without a RF IDeas PRODUCT Redistributable Code. If you are authorized and choose to redistribute Sample Code

(Redistributables) as described in Section 1.4, you agree to: (a) distribute the Redistributables in object code only in conjunction with and as a part of a software application product developed by you using the PRODUCT accompanying this EULA that adds significant and primary functionality to the SOFTWARE PRODUCT (Licensed Product); (b) not use RF IDeas name, logo, or trademarks to market the Licensed Product; (c) include a valid copyright notice on the Licensed Product;

(d) indemnify, hold harmless, and defend RF IDeas from and against any claims or lawsuits, including attorneys fees, that arise or result from the use or distribution of the Licensed Product; (e) otherwise comply with the terms of this EULA; and (f) agree that RF IDeas reserves all rights not expressly granted. You also agree not to permit further distribution of the Redistributables by your end users except: (1) you may permit further redistribution of the Redistributables by your distributors to your end-

user customers if your distributors only distribute the Redistributables in conjunction with, and as part of, the Licensed Product and you and your distributors comply with all other terms of this EULA; and (2) in the manner described in Section 1.4.

*Separation of Components. The PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one computer.

*Single COMPUTER. The PRODUCT is licensed with the COMPUTER as a single integrated product. The PRODUCT may only be used with the COMPUTER.

*Rental. You may not rent or lease the PRODUCT without permission from RF IDeas.

*Software Transfer. You may permanently transfer all of your rights under this EULA only as part of a sale or transfer of the COMPUTER, provided you retain no copies, you transfer all of the PRODUCT (including all component parts, the media and printed materials, any upgrades, this EULA and, if applicable, the Certificate(s) of Authenticity), AND the recipient agrees to the terms of this EULA. If the PRODUCT is an upgrade, any transfer must include all prior versions of the PRODUCT.

*Termination. Without prejudice to any other rights, RF IDeas may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the SOFTWARE PORTION OF THE PRODUCT and all of its component parts. 3. UPGRADES. If the SOFTWARE PORTION OF THE PRODUCT is an upgrade from another product, whether from RF IDeas or another supplier, you may use or transfer the PRODUCT only in conjunction with that upgraded product, unless you destroy the upgraded product. If the SOFTWARE PORTION OF THE PRODUCT is an upgrade of a RF IDeas product, you now may use that upgraded product only in accordance with this EULA. If the SOFTWARE PORTION OF THE PRODUCT is an upgrade of a component of a package of software programs which you licensed as a single product, the SOFTWARE PORTION OF THE PRODUCT may be used and transferred only as part of that single product package and may not be separated for use on more than one computer. 1.3 Storage/Network Use. You may also store or install a copy of the SOFTWARE PRODUCT on a storage device, such as a network server, used only to install or run the SOFTWARE PRODUCT on computers used 4. OEM COPYRIGHT. All title and copyrights in and to the PRODUCT

(including but not limited to images, photographs, animations, video, audio, music, text and applets, incorporated into the PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PORTION OF THE PRODUCT, are owned by RF IDeas or its suppliers. The PRODUCT and SOFTWARE PORTION OF THE PRODUCT is protected by copyright laws and international treaty provisions. You may not copy the printed materials accompanying the PRODUCT. OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OF PURPOSE. Since some states do not allow such exclusion of limitation of incidental or consequential damages for consumer products, check the statute of the state in which your business resides. 5. DUAL-MEDIA SOFTWARE. You may receive the SOFTWARE PORTION OF THE PRODUCT in more than one medium. Regardless of the type or size of medium you receive, you may use only one medium that is appropriate for your single computer. You may not use or install the other medium on another computer. You may not loan, rent, lease, or otherwise transfer the other medium to another user, except as part of the permanent transfer (as provided above) of the SOFTWARE PORTION OF THE PRODUCT. 6. OEM PRODUCT SUPPORT. Product support for the product is not provided by RF IDeas or its subsidiaries. For product support, please refer to the OEM supplies support number provided in the documentation. Should you have any questions concerning the EULA, or if you desire to contact OEM for any other reason, please refer to the address provided in the documentation provided. FOR THE LIMITED WARRANTIES AND SPECIAL PROVISIONS PERTAINING TO YOUR PARTICULAR JURISDICTION, PLEASE REFER TO YOUR WARRANTY BOOKLET INCLUDED WITH THIS PACKAGE OR PROVIDED WITH THE SOFTWARE PRODUCT PRINTED MATERIALS. Limited Warranty: RF IDeas warrants to the original buyer of this product, that the hardware and related disk(s) are free of defects in material and workmanship for a period of one year from date of purchase from RF IDeas or from an authorized RF IDeas dealer. Should the RF IDeas products fail to be in good working order at any time during the one-year period, RF IDeas will, at its option, repair or replace the product at no additional charge, provided that the product has not been abused, misused, repaired or modified. This warranty shall be limited to repair or replacement and in no event shall RF IDeas be liable for any loss of profit or any commercial or other damages, including but not limited to special, incidental, consequential or other similar claims. No dealer, distributor, company, or person has been authorized to change or add to the terms of this agreement, and RF IDeas will not be bound by any representation to the contrary. RF IDeas SPECIFICALLY DISCLAIMS ALL This warranty gives you the specific legal rights in addition to any rights that you have under the laws of the state in which your business resides or operates. Returns: RF IDeas products which require Limited Warranty service during the warranty period shall be delivered to the nearest authorized dealer or sent directly to RF IDeas at the address below with proof of purchase and a Return Materials Authorization (RMA) Number provided by RF IDeas Technical Support Dept. Replacement parts or complete boards become the property of RF IDeas. If the returned board or unit is sent by mail, the purchaser agrees to pre-pay the shipping charges and insure the board or unit or assume the risk of loss or damage which may occur in transit. The purchaser is expected to employ a container equivalent to the original packaging. Copyright: Copyright by RF IDeas 2017. All rights reserved. Reproduction or distribution of this document in whole or in part or in any form is prohibited without express written permission from RF IDeas. Trademarks: All RF IDeas products are trademarks of RF IDeas. All other product names or names are trademarks or registered trademarks of their respective holders. Applicable Patents: RF IDeas pcProx Plus card readers supporting HID formats retain US Patent No. 5,952,935 and U.S. Patent No. 7,439,862. Disclaimer: This Reference Guide is printed in the U.S.A. Any resemblance mentioned in the Reference Guide to persons living or dead, or to actual corporations or products is purely coincidental. RF IDeas believes that the information contained in this manual is correct. However, RF IDeas does not assume any responsibility for the accuracy of the content of this User Manual, nor for any patent infringements or other rights of third parties. RF IDeas reserves the right to make any modifications in either product or the manual without giving prior written notification. FCC/ISED Compliance Statement ISED French Compliance Statement FCC ID: M9MF80100 (Multi-protocol USB Card Reader) IC: 6571A-F80100 (Multi-protocol USB Card Reader) Pursuant to FCC 15.21 of the FCC rules, changes not expressly approved by RF IDeas might cause harmful interference and void the FCC authorization to operate this product.

"Conformment la FCC 15.21 de la rglementation FCC, les changements ne sont pas expressment approuvs par les ides RF peuvent causer des interfrences nuisibles et annuler l'autorisation FCC d'utiliser ce produit. Note: This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product complies with FCC OET Bulletin 65 radiation exposure limits set forth for an uncontrolled environment. The reader may not recognize value cards in the presence of high RF fields. If the current reading is erratic, the user shall take the following step: Move the equipment from any known transmitters nearby. For more information contact Tech Support at (866) 439-4884 or TechSupport@RFIDeas.com. Note: Cet appareil est conforme la Partie 15 des rglements de la FCC et d'Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) Ce dispositif ne doit pas causer d'interfrences nuisibles, et (2) cet appareil doit accepter toute interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. Ce produit est conforme aux normes FCC OET Bulletin 65 l'exposition aux rayonnements limites dfinies pour un environnement non contrl. Le lecteur peut ne pas reconnatre des cartes de valeur, en prsence de champs RF leves. Si la valeur actuelle est erratique, l'utilisateur doit passer l'tape suivante: Dplacer le matriel de toute metteurs connus proximit. Pour plus d'informations contactez le support technique au 866.439.4884 or TechSupport@RFIDeas.com. RF IDeas, Inc. 4020 Winnetka Avenue Rolling Meadows, IL 60008 www.RFIDeas.com Toll Free: 866-439-4884 Voice: 847-870-1723 Fax: 847-483-1129 is a registered trademark of RF IDeas Inc. Trademarks not belonging to RF IDeas are property of their respective companies. 2017 RF IDeas, Inc. All rights reserved. Products are subject to change without notice. 99009230

Single Badge Solutions foridentification and Access ID Label/Location FCC ID: M9MF80100 IC: 6571A-F80100 Model: RDR-80531AKU ID Label

"= PDR-80531AKU rf IDEAS EN LAAT TATTOO TD P| we tDeas.com FCC ID: MOMF80100 IC: 6571A-F80100 a }This device may not cause hae interference. Q) This device must accept awpktetince thatmay |

mais undesireable operation. PCB-1080-03E -

DC:2002Q FW: LNC160900UPX700.H/LNRO20400-

KHAN

| FU05000001 Ls Fe C

"* RDR-80034AKU rf IDEAS UAT A TE A LY Av RFtD2as. com FCC ID: M9MF80100 Ic: 6571A-F 80100

(A) This device may not cause ae ful interference. Q) This device must accept any interference that may :

Cause undesireable operation. PCB-1080-03E ;

DC:2004Q FW: LNC160900UPX700. at ll LL ll &

FDOIO00001 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone * (866) 439-4884 toll free (847) 483-1129 fax Sales@RFiDeas.com www.RFiDeas.com Single Badge Solutions foridentificationand Access Model: RDR-80541 AKU ID Label RDR-80541 AKU-RSOP rf IDEAS MU AUVEN SYA viene a aniensctae FCC ID: M9MF80100 IC: 6571A-F80100 This product complies with Part 15 ofthe FCC Rules. Operation is subject te the followingtwo conditions:

(1) This device may not cause harmful interference. (23 This device mustaccept any interference that may Cause undesireable operation. PCB-1080-03 DC:2002Q FW: LNC160900UPX700.H/LNR020400 08.0 0 1 as FU05000001 2FE C Be Bs A

"= RDR-80534AK5 rf IDEAS BLED TNT PPE IN HI, ww RF tDeas.com FCC ID: M9MF80100 IC: 6571A-F80100

(1) This device may not cause harmful interference. (2) This device must accept any interference that may -

cause undesireable operation. PCB-1080-03E -

DC:2002Q FW: LNC160900SPX700.H/LNRO20400 MOM FS05000001 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free * (847) 483-1129 fax Safes@RFiDeas.com www.RFiDeas.com Single Badge Solutions foridentification and Access Model: RDR-80531AK7 ID Label RDR-80531AK7 rf IDEAS UU] www.RFIDeas.com FCC IB: M9MF80100 IC: 6571A-F80100

(1) This device may not cause harmful interference. (2) This device mustaccepl any interference that may |

Cause undesireable operation. PCB-1080-03E -

SeriNor DC:2002Q FW: LNC160900SPX700.H/LNRO20400 UY TMM V0 V0 a FS05700001

" RDR-80031AK7 rf IDEAS UTD TRTE YU MTV YD A www.RFIDeas.com FCC ID: M9MF80100 IC: 6571A-F80100

(1) This device may not cause harmful interference. (2) This device must accept any interference that may. Cause undesiteable operation. PCB-1080-03E -

SerilNo: DC:2004Q FW: LNC160900SPX700.H/LNR0O20400 -

WN) YANO ADE MOODY AEH AT Ros] Sy FS01000001 ZS FE C BS! X 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone * (866) 439-4884 toll free * (847) 483-1129 fax Sales@RFiDeas.com www.RFiDeas.com Single Badge Solutions foridentification and Access Model: OEM-805N11KU ID Label

M/N: OEM-805N11KU rf IDEAS FW: LNC160900UPX700.H/LNRO20400 = www.RFiDeas.com FCC ID: M9MF80100 IC: 6571A-F80100 De: 2002 I: A peti] FE C UTE AGE TH Model: OEM-805N11K5 ID Label M/N: OEM-805N11K5 rf IDEAS

| FW: LNC160900SPX700.H/LNR0O20400 www.RFiDeas.com

| | FCC ID: M9MF8ot00 IC: 6574A-F80100 DC: 2004 CE CE ULTIMO LITT FS050011 Model: OEM-805N11K7 ID Label M/N: OEM-805N11K7 rf IDEAS FW: LNC160900SPX700.H/LNRO20400 = www.RFiDeas.com

| | FCC 1D: M9MF80100 IC: 6571A-F80100 DC: 2004 ee =n ST |

PCB-1080-03 FS05B011 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free * (847) 483-1129 fax Sales@RFiDeas.com www.RFiDeas.com Single Badge Soiutions forldentificationand Access Material of Serial Number Label

- Type: Zebra/Identco CTTL302-730-2 Silver Label

- Color: Silver with black text

- Size of Label: 1.00 x 2.0

- Adhesive to Permanent

- This label will be installed on the bottom of the EUT (see picture)

~ RDR-B0631AKU TUE FCC iD: MMFEDTOD

- Type: Zebra PolyPro Label PN: 18930

- Color: White with black text

- Size of Label: 1.50 x 0.5

~ Adhesive to Permanent :

- This label will be installed on the bottom of the EUT for OEM models 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free (847) 483-1129 fax Sales@RFiDeas.com www.RFiDeas.com Single Badge Solutions for identification and Access Sincerely, RF [DeasNhc. 4020 Winnetka Avenue Rolling Meadows, IL 60008 Tel: (847) 870-1723 ext. 412 Fax: (847) 483-1129 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone * (866) 439-4884 toll free * (847) 483-1129 fax Sales@RFiDeas.com www.RFiDeas.com

SOLVING A WAVE OF EMI COMPLIANCE PROBLEMS Romeoville, IL 60446 12 Devonwood Ave Tel: (815) 293-0772 Fax: (815) 293-0820 Test Lab Attestation Letter November 25 to December 11, 2019 RF Ideas FCC ID: M9MF80100 Wave ID RDR-80031AKU RDR-80531AKU RDR-80541AKU-RSOP RDR-80531AK7 RDR-80531AK5 RDR-80031AK7 Joseph Strzelecki, Richard Tichgelaar, Dave Jarvis, Chris Dalessio Radiometrics Midwest Corporation Radiometrics declares that this Unit has been tested in accordance with the test method identified in this test report and that we observed it being tested. We also declare that the Unit complies with the relevant limits. All instrumentation and accessories used to test this unit for compliance to the indicated test method are calibrated regularly in accordance with ISO 17025:2005 requirements by laboratories accredited by A2LA, NVLAP, or ACLAS for the measurement parameters. Radiometrics Midwest Corporation 12 Devonwood Ave Romeoville IL 60446 Joseph Strzelecki Date of Test:

Applicant Name:

FCC ID:

Test Items:

Name of Engineer Performing Test:

Statement of Compliance:

The measurements were made at:

Test Lab Witness-

Signature of Test Lab Witness:

Full Name, Typed:

Joseph R Strzelecki Title of Witness: Senior EMC Engineer joe@radiomet.com Email Address:

Phone No.: 815-293-0772 Test Lab Stamp:

Page 1 of 1

Single Badge Solutiens forldentitication and Access January 24, 2020 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

| appoint Joseph Strzelecki of Radiometrics Midwest Corporation to act as RF IDeas, Inc. agent in the preparation of application under Part 15, Title 47 of the Code of Federal Regulation of the Federal Communications Commission. | certify that the exhibits properly describe the device being submitted under this application and will implement any changes described in the test report. Radiometrics is authorized to act on its behalf in all matters relating to application for Equipment authorization. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits. that includes FCC benefits. pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988. 21 U.S.C. 853(a). This authorization is valid until further written notice from the applicant. Sincerely, 4020 Winnetka Avenue, Rolling Meadows, IL 60008 Tel: (847) 870- 1723 EXT. 412 Fax: (847) 483-1129 Email: deottingham@RFIDeas.com 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone * (866) 439-4884 toll free + (847) 483-1129 fax Sales@RFiDeas.com www.RFiDeas.com

RFID Solutions forldentification and Access Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: Jan. 09, 2020 SUBJECT: FCC Application for FCC ID: M9MF80100 To Whom It May Concern:

We, the undersigned, hereby authorize TIMCO ENGINEERING. INC.. at 849 NW State Road 45, Newberry, Florida 32669 on our behalf. to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by TIMCO ENGINEERING. INC.. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We. the applicant. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, ham / President RF Deas, Inc. 4020 Winnetka Avenue Rolling Meadows, IL 60008 Tel: (847) 870-1723 ext. 412 Fax: (847) 483-1129 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free + (847) 483-1129 fax Sales@RFiDeas.com www.RFIDeas.com

i Badge Solutions forldentification and Access Jan. 9, 2020 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: M9MF80100 Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name e Schematic e SCH-1080-03-80UCA-NOSIM, e SCH-1080-03-85UCA, e SCH-1080-03-859SCA e Block Diagram e Block Diagram-1080-03_USB-Serial e Theory of Operation e TheoryOfOperations - RDR-

805x1AKx The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. In additional, pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request the commission to grant short-term confidential treatment of information accompanying this application on the following attachments until March 31, 2020 as outlined below:

Exhibit Type e Internal & External Photos e Test setup Photos e User Manual 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free * (847) 483-1129 fax Sales@RFiDeas.com www.RFIDeas.com RF Badge Solutions for!dentification and Access Sincerely, RF IDeasNinc. 4020 Winnetka Avenue Rolling Meadows, IL 60008 Tel: (847) 870-1723 ext. 412 Fax: (847) 483-1129 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free * (847) 483-1129 fax Sales@RFlDeas.com www.RFiDeas.com

DECLARATION OF SIMILARITY January 23, 2020 To:

FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Innovation, Science and Economic Development Canada Certification and Engineering Bureau P.O. Box 11490, Station H 3701 Carling Ave., Building 94 Ottawa, Ontario K2H 8S2 Canada To whom it may concern:

We, RF IDeas, Inc. hereby declare that product: Wave ID Plus, Regulatory model: FCC ID: M9MF80100, IC:

6571A-F80100 are electrically identical with the same electromagnetic emissions and electromagnetic compatibility characteristics. All Main PCBA and Antenna PCBA listed on the table below were fully tested and the results of which are featured in Radiometrics' project: RP-9208. Interface Main PCBA USB PCB-1080-03 Antenna PCBA Description PCB-1101-02 OEM WaveID Plus USB for Ricoh SOP Part Number RDR-80541AKU-

RSOP RDR-80031AKU USB PCB-1080-03E PCB-1098-05 WaveID Plus Desktop SE - USB Keystroke RDR-80032AKU USB PCB-1080-03E PCB-1098-05 WaveID Plus Desktop SE - USB SDK RDR-80531AKU USB PCB-1080-03E PCB-1098-05 WaveID Plus Desktop - USB Keystroke RDR-80532AKU USB PCB-1080-03E PCB-1098-05 WaveID Plus Desktop - USB SDK OEM-805N11KU USB PCB-1080-03E PCB-1098-05 WaveID Plus OEM (no housing) - USB Keystroke OEM-805N21KU USB PCB-1080-03E PCB-1098-05 WaveID Plus OEM (no housing) - USB SDK RDR-80031AK7 Serial PCB-1080-03E PCB-1098-05 WaveID Plus Desktop SE Serial - 9VDC vial Dongle RDR-80531AK5 Serial PCB-1080-03E PCB-1098-05 WaveID Plus Desktop Serial - 5VDC Pin 9 PWR RDR-80531AK7 Serial PCB-1080-03E PCB-1098-05 WaveID Plus Desktop Serial - 9VDC vial Dongle OEM-805N11K5 Serial PCB-1080-03E PCB-1098-05 WaveID Plus OEM Serial (no housing) -

5VDC Pin 9 PWR OEM-805N11K7 Serial PCB-1080-03E PCB-1098-05 WaveID Plus OEM Serial (no housing) -

9VDC via Dongle The printed circuit boards are the same with minor electrical components between the USB and Serial 5V DC &

9V DC models. Serial readers will have the RS232 IC and the 9V model will get an onboard regulator. The Transmitter on all models has built in 5 Volt regulation. 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone (866) 439-4884 toll free (847) 483-1129 fax Sales@RFIDeas.com www.RFIDeas.com The products will not be sold to the general public. RF Ideas or the OEM will be responsible to ensure the proper installation in accordance with RF Ideas requirements. All of the model numbers use the same frequency determining circuitry. The 13.56 MHz and 125 kHz trasnmitter circuits are identical on all boards. There are two different shapes of Antennas. Each antenna was tested. The antenna has a unique connector to ensure no other antennas will be used. The antenna is internal to the EUT and it is not readily available to be modified by the end user. Please contact me should there be need for any additional clarification or information. Sincerely, ________________________ Shiung Lo RF IDeas, Inc. / Regulatory Administrator 4020 Winnetka Avenue, Rolling Meadows, IL 60008 Tel: (847) 870- 1723 Fax: (847) 483-1129 Email: slo@RFIDeas.com 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone (866) 439-4884 toll free (847) 483-1129 fax Sales@RFIDeas.com www.RFIDeas.com

Single Badge Saletan at HaatN tis WH Neca Limited MODULAR APPROVAL LETTER Modular Approval Requirement

(i) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements.

(ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. Yes Yes No No

(iii) The modular transmitter must have its own power supply regulation. Yes

(iv) The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Yes

(v) The modular transmitter must be tested in a stand-

alone configuration Yes

(vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization.

(viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Yes Yes Yes 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free (847) 483-1129 fax Sales@RFiDeas.com www.RFIDeas.com Single Badge Solutions foridentitication and Access Regards, David Cot ham / President RF IDeas, Hac. 4020 Winnetka Avenue Rolling Meadows, IL 60008 Tel: (847) 870-1723 ext. 412 Fax: (847) 483-1129 4020 Winnetka Avenue, Rolling Meadows, IL 60008

(847) 870-1723 phone + (866) 439-4884 toll free (847) 483-1129 fax Sales@RFiDeas.com www.RFIDeas.com