146mm m m 2 8 Beams Battery Floodlight 1. Connect your Battery Floodight. Download the Ring app. The app walks you through setting up and managing your Floodlight. Search for Ring in one of these app stores, or visit: ring.com/app Set up your Ring Beams Bridge. The Bridge connects your Ring Beams lights to the rest of your Ring system. Your Bridge must be up and running before you set up your Floodlight. Download from Windows Store To set up your Bridge, follow the instructions in the Ring app or Bridge user manual. Download from Windows Store 3 Insert the batteries. Twist and pull off the front of the light, then press the side buttons on the battery compartment to open. Insert four D-cell batteries. 4 Set up your Floodlight in the Ring app. In the app, tap Set Up a Device. When prompted, select Beams and follow the in-app instructions. Once setup is complete, slide the battery cover back onto your Floodlight. Doorbells Security Cams Chimes Beams Alarm 5 2. Install your Floodlight. Press the tab on the side of the base, and slide the base off of your Floodlight. Use the base as a template to mark the screw holes. 6 Hold the base against the surface and drive the three mounting screws. The arrow marked UP on the base should point upwards once the base is mounted. Align your Floodlight with the base and slide it to the left to lock it in. The motion sensor is adjustable. Try various angles for the best performance. 7 For additional help, visit: ring.com/help Or give us a call US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit:
ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents 2018 Ring LLC or its affiliates. RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates. Last updated: 09/18/18 may a B to 15
(1) to may could with with digital Rules. device subject complies conditions:
device cause occur can of frequency to harmful undesired this interference limits protection must not device that compliance following received, the party Class for pursuant Part in aresidential used and in there no is guarantee interference to radio to encouraged to try the is Operation interference any accept approved expressly by the two including responsible device, for interference harmful against installed if energy and, not However, communications. radio does equipment equipment off and FCC 15 of the Part This this and interference,
(2) not modifications Changes or operation. cause equipment. authority operate to the user's the void to comply been has tested found equipment and This NOTE:
reasonable to limits aredesigned These provide Rules. the FCC equipment uses radio generates, can and radiate installation. This instructions, the cause harmful may interference accordance with installation.If not in particular this a will that interference television which be the by determined reception, turning interference or the measures:
following one more by
--
the Reorient antenna. receiving or relocate the Increase separation between the
--
equipment outlet Connect circuit a on
--
equipment into the receiver the to from connected. which the
--
or dealer an FCC warning The device has been evaluated to meet general RF exposure requirement. Caution: This Transmitter must be installed to provide separation distance of at least 20cm from all persons. FCC / IC RF Radiation Dclaration d'exposition Attention: Cet metteur doit tre install pour fournir une distance de sparation d'au moins 20 cm de toute personne. that Consult RF experienced cause the on, and different harmful user is radio/TV or correct receiver. statement:
technician an is help. for of the Industry Canada This device complies with Industry Canada licence-exempt RSS standard(s): Operation is subject to the following Two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.