FCC ID: 2AEUPBHAFL031 Floodlight Cam Wired Pro

User Guide Floodlight Cam Wired Pro WARNING: Risk of electrical shock. Disconnect power at the fuse or circuit breaker before installing. Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240 VAC 50/60 Hz power source. Properly ground fixture. Always follow code standards when installing wired connections. Quick Start 1. Open the Ring app and select Set Up a Device. Then follow the in-app instructions. 2. Scan this code. This identifies your Ring device to make setup fast and easy. CAUTION: Risk of fire. Do not install near combustible or flammable surfaces. QR+FR NOTICE: Do not connect this light fixture to a dimmer switch or timer. Your Floodlight Cam must be installed on a 4 round UL listed weatherproof electrical box. This manual is for informational purposes only. Working with electricity can be dangerous unless proper safety precautions are taken. If you are not comfortable or are inexperienced with the processes and tools described in this manual, we recommend that you hire a licensed electrician. Shut off power at the breaker!

Prep your Floodlight Cam for installation. Remove your existing floodlight. Choose your screws. Install the plastic mounting plate. Youll be working with electrical wires during the install process. If you dont know where your breaker is or how to turn off power to your floodlight circuit, we recommend you hire a licensed electrician. First, rotate the lights out of the way, like this With power off at the breaker, remove your existing floodlight from the junction box its attached to and disconnect the wires. If youre mounting on an eave or overhang, your camera is already in position. If youre mounting to a wall, rotate the camera into position like this... If there is a metal bracket attached to your junction box, remove that as well. Pull gently from the opening of the plastic plate to free it from the fixture, then feed your power wires though the opening. With your power wires fed through the mounting plate, center it over the metal mounting bracket. If youre installing on a wall, the UP arrow should point up. If youre installing under an eave, it should point towards the wall. Then, insert one of the screws from Bag B or C into the center hole, and tighten to secure. Select a set of screws from the bags marked A through F that fit your junction box to secure the metal mounting bracket. One size does not fit all here, so we sent several. Save a screw from either Bag B or C. You will use it on the next page. Bag A Standard screws. These should fit most junction boxes. Bag B & C Longer screws to reach the screw holes in recessed junction boxes. Bag D, E & F Best for older boxes with smaller screw holes. Attach the metal mounting bracket. With the screws you selected in the previous step, secure the metal mounting bracket to your junction box using either pair of screw holes. Be sure to align the bracket so that the FRONT text faces outwards. 2 3 4 5 6 7 8 Hang it up. Connect the wires. Mount the light fixture. Restore power at the breaker. Review, share and download. What is Ring Protect?

Locate the nylon strap on the back of your Floodlight Cam light fixture, and loop the buckle at the end over the hook on the mounting plate. Make sure the buckle and hook are secure before releasing the light fixture. Tuck the power wires into the junction box, then align the two holes on the light fixture with the threaded posts on the plastic mounting plate. Slide the light fixture onto the posts and push it firmly into place. Secure your fixture using two of the hex cap nuts from Bag G over the ends of the threaded posts. Remove the reversible bit from the included screwdriver and use the handle to tighten the hex cap nuts. Once your Floodlight Cam is secured, apply a weatherproof silicone caulk or sealant (not included) around the outside, where the Floodlight Cam and junction box meet. The green wire on your Floodlight Cam is the ground wire. With power still off at the breaker, use a wire nut from the bag marked G to connect the green (or ground) wire from your Floodlight Cam to the green wire coming from your junction box. The white wire on your Floodlight Cam is a neutral wire. Use another wire nut from the bag marked G to connect the white wire from your Floodlight Cam to the white (or neutral) wire coming from your junction box. The black wire on your Floodlight Cam is a hot wire. Use another wire nut from the bag marked G to connect the black wire from your Floodlight Cam to the black (or hot) wire from your junction box. Give all 3 wire connections and wire nuts a gentle tug to make sure they are secure. WARNING: If you cant easily identify the wires coming out of your junction box, or have difficulty with or are uncomfortable connecting them, consult with a licensed electrician. Now that your Floodlight Cam is installed, you can turn power back on at the breaker. The lamps on your Floodlight Cam will flash once its powered on. Your new device comes with a free 30-day trial of our Ring Protect video recording service. Ring Protect is a subscription service that stores videos from your Ring devices. To continue your subscription and save your videos, please visit ring.com/protect-plans Why do I want it?

Ring lets you interact with visitors and monitor your property in real time, while Ring Protect allows you review and share those videos anytime. How much does it cost?

Ring Protect starts at $3 USD/month or $30 USD/year per Ring doorbell or camera.*

How do I sign up?

Simply log into your Ring account at ring.com/protect-plans, and follow the on-screen instructions. For additional help, visit ring.com/help Or give us a call US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit ring.com/callus 9 10 11 12 Complete setup in the Ring App. Once your Floodlight Cam powers on, follow the instructions to continue with setup in the app.

*$5 CAD per month or $50 CAD per year xx-xxxxxx-xx For information on our warranty, theft protection, and Ring Protect Plans, visit ring.com/legal 2021 Ring LLC or its affiliates. Ring and all related marks are trademarks of Ring LLC or its affiliates.

Important Product Information SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. WATCH FOR SMALL PARTS. The device and accessories may present a choking hazard to small children and pets. Keep them out of reach of small children and pets. WARNING: Electrical shock hazard. Disconnect power to installation area at your circuit breaker or fuse box before beginning installation. Always use caution when handling electrical wiring. Installation by a qualified electrician may be required in your area. Refer to your local laws and building codes before performing electrical work; permits and/or professional installation may be required by law. FIRE RISK: Do not mount near combustible or flammable surfaces. Your device is water resistant and is suitable for outdoor use. However, your device is not intended for underwater use. To protect against electric shock, do not intentionally submerge or immerse your device in water or expose your device to other liquids. Do not spill any food or beverages on your device. Do not attempt to clean or polish your device with or expose your device to oil, lotion, or other abrasive substances. Do not expose your device to salt water or other conductive liquids. Do not expose your device to pressurized water, high velocity water, or extremely humid conditions (such as a steam room). Do not attempt to dry your device with an external heat source, such as a microwave oven or a hair dryer. To avoid risk of electric shock, do not touch your device or any wires connected to your device during a lightning storm while your device is powered. If your device appears to be damaged, discontinue use immediately. Do not install on the ground. Your device should be installed outdoors to a wall or eave. To reduce the risk of fall, take extra caution when using a ladder or similar equipment to mount your device. Do not cover the device while operating. Do not open the hous-

ing. Your device does not contain serviceable parts or replaceable LEDs. Protect this device from sunlight. Disconnecting the wires will power the device off. Do not use the device if the wires or housing are defective, there is a risk of electric shock. Do not cut any wires with factory installed wire connectors or remove the wire connectors. Do not install on circuits feeding motor loads such as kitchen appliances, HVAC equipment, washer/ dryer or garage door openers. Do not install when it is raining. Do not stare directly at the LEDs for more than a few seconds to avoid eye injury. Only use accessories that are recommended by the manufacturer. Use of third-party accessories may lead to damage to your device or the accessory and may cause fire, electric shock, or injury. SAFELY CONNECTING YOUR RING FLOODLIGHT CAM WIRED PRO TO YOUR HOMES ELECTRICAL WIRING You must turn off the power source to the electrical box at your homes circuit breaker or fuse and test that the power is off BEFORE removing an existing floodlight or light fixture, installing the device, or touching electrical wires. Failure to turn off circuit breaker or fuse could result in FIRE, ELECTRIC SHOCK, or OTHER INJURY or DAMAGE. More than one disconnect switch may be required to turn off the equipment before servicing. If the electrical wiring in your home does not resemble any of the diagrams or instruc-

tions provided with the device, if you encounter damaged or unsafe wiring, or if you are unsure or uncomfortable in performing this installation or handling electrical wiring, please consult a qualified electrician in your area. Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240 VAC 50/60 Hz power source. Properly ground fixture. Always install wiring connections in accor-

dance with local code standards. Product Specifications Device Name: Ring Floodlight Cam Wired Pro Model Number: 5B28S4 Electrical Rating: Hardwired (100 to 240V) Temperature Rating: -5F to 118F (-20.5C to 48C) RECYCLING YOUR DEVICE PROPERLY In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to amazon.com/devicesupport. TERMS OF SERVICE AND WARRANTY Use of the product is subject to your registration with Ring and your agreement with the Terms of Service found at ring.com/terms. To review your warranty coverage, please refer to the enclosure inside this box or visit ring.com/warranty. For Consumers in the USA This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by inputting such Products FCC ID (which can be found on the device) into the FCC ID Search form available at fcc.gov/oet/ea/fccid. The party responsible for FCC compliance is:

Ring LLC, 1523 26th St. Santa Monica, CA USA, 90404 FCC RADIATION EXPOSURE STATEMENT This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunc-

tion with any other antenna or transmitter. THEFT PROTECTION If your Ring camera or doorbell product is stolen at any time after your purchase, Ring will replace the stolen device at no charge to you. This theft protection is not trans-

ferable and applies only to the original consumer purchaser. Coverage of this theft protection is limited to one (1) replacement only for each Ring camera or doorbell product that you have purchased. Theft protection does not apply to any products purchased from third party sellers on eBay and other online marketplaces. Any claim based on theft of your Ring camera or doorbell product must be submitted within fifteen (15) days of the theft and include the original sales receipt, and a copy of a police report evidencing that you reported the theft to the police. Failure to report the theft to police voids this theft protection. Ring LLC 1523 26th St. Santa Monica, CA 90404 2021 Ring LLC or its affiliates. Ring and all related marks are trademarks of Ring LLC or its affiliates. XX-XXXXXX-XX

24.0mm DSN:

G071KX01YWWD####

MAC Address:

54:E0:19:aa:bb:dd D H A V 2 45.0 mm 24.0mm DSN:

G071KX01YWWD####

MAC Address:

54:E0:19:aa:bb:dd D H A V 2 45.0 mm

Ring LLC 12515 Cerise Ave, Hawthorne, CA 90250 USA Tel:

8006561918

; Fax:

3102272217 CC OTH 00458819 2022 TR Date:

July 29, 2022 FCC Laboratory 7435 Oakland Mills Rd. Columbia, MD 21046 SUBJECT:

Application for Class II Permissive Change for FCC ID:

2AEUPBHAFL031 This is to request a Class II Permissive Change for FCC ID:

2AEUPBHAFL031, original granted on 05/21/2021) The

(1)

(2) changes software filed under this application Enable Lora DTS 500k SF8SF9SF10SF11 operation mode Enable Lora 125K FHSS SF8SF9 operation mode are:

Except listing above, the hardware and software security remains identical to original granted. Sincerely, Elvira Palmeda ring-certifications@amazon.com

Ring LLC 12515 Cerise Ave, Hawthorne, CA 90250 USA Tel: 8006561918 ; Fax: 3102272217 CC OTH 00458819 2022 TR Date: July 29, 2022 FCC Laboratory 7435 Oakland Mills Rd. Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AEUPBHAFL031 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Best Regards, ______________________ Elvira Palmeda ring-certifications@amazon.com

CC OTH 00458819 2022 TR Ring LLC 12515 Cerise Ave, Hawthorne, CA 90250 USA Tel: 8006561918 ; Fax: 3102272217 Date: July 29, 2022 To whom it may concern, Please be notified that I, Elvira Palmeda, have designated Sporton International Inc. as the agent being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Sporton International Inc. on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is limited to the product of as following:

FCC ID: 2AEUPBHAFL031 If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Sincerely yours, Elvira Palmeda ring-certifications@amazon.com

Ring LLC 1523 26th Street, Santa Monica, CA 90404, United States Tel: 8006561918 ; Fax: 3102272217 Date: March 30, 2021 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for Confidentiality FCC ID: 2AEUPBHAFL031 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Part List Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Carro Hsieh carro.hsieh@ring.com

Ring LLC 1523 26th Street, Santa Monica, CA 90404, United States Tel: 8006561918 ; Fax: 3102272217 Date: March 30, 2021 To whom it may concern, Please be notified that I, Carro Hsieh, have designated Jones Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jones Tsai in Sporton International Inc. on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. This authorization is limited to the product of as following:

FCC ID: 2AEUPBHAFL031 If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Sincerely yours, Carro Hsieh carro.hsieh@ring.com

Ring LLC 1523 26th Street, Santa Monica, CA 90404, United States Tel: 8006561918 ; Fax: 3102272217 Federal Communications Commission Office of Engineering and Technology Laboratory Division Date: April 7, 2021 7435 Oakland Mills Rd. Columbia, MD 21046 SUBJECT: Application for Class II Permissive Change for FCC ID: 2AEUPBHAFL031 This is to request a Class II Permissive Change for FCC ID: 2AEUPBHAFL031, original granted on 04/06/2021) The software change filed under this application is:

Enable LoRa FHSS operation via embedded software. Except listing above, the hardware, software security remains identical to original granted. Sincerely, Carro Hsieh carro.hsieh@ring.com

Ring LLC 1523 26th Street, Santa Monica, CA 90404, United States Tel: 8006561918 ; Fax: 3102272217 Date: April 6, 2021 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for Confidentiality FCC ID: 2AEUPBHAFL031 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. Test Setup Photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Carro Hsieh carro.hsieh@ring.com