FCC ID: 2AEUPBHAPB001 Pathlight

Beams Path Light 1. Connect your Path Light. Download the Ring app. The app walks you through setting up and managing your Path Light. Search for Ring in one of the app stores below, or visit:

ring.com/app Download from Windows Store Set up your Ring Beams Bridge. The Bridge connects your Ring Beams lights to the rest of your Ring system. Your Bridge must be up and running before you set up your Path Light. To set up your Bridge, follow the instructions in the Ring app or Bridge user manual. 3 Insert the batteries. Push in the button on the front and slide off the battery cover. Insert four D-cell batteries. Set up your Path Light in the Ring app. In the app, tap Set Up a Device. When prompted, select Beams and follow the in-

app instructions. Once setup is complete, slide the battery cover back onto your Path Light. Doorbells Security Cams Chimes Beams Alarm 4 5 2. Install your Path Light. Hammer the stake into the ground in your chosen location. Take care to point the Sensor Direction arrow on the stake toward the area you want to monitor for motion. If youre installing multiple Path Lights, space them 5-7 feet apart for the best motion sensing performance. Lower your Path Light onto the stake and twist clockwise to lock it in. 6 7 For additional help, visit: ring.com/help Or give us a call US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit:

ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents 2018 Ring LLC or its affiliates. RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates. Last updated: 09/13/18 Warnings This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Opera-

tion is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. de moin de 20 cm. Installer les antennes de facon ce que le personnel ne puisse approcher 20 cm ou moins de la position centrale de l antenne. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. La FCC des ltats-unis stipule que cet appareil doit tre en tout temps loign dau moins 20 cm des personnes pendant son functionnement. MPE Reminding To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installes doivent tre situes de facon ce que la population ne puisse y tre expose une distance

108mm Beams Spotlight m m 0 9 02_Spotlight_MANUAL.indd 1 9/28/18 4:19 PM 1. Set up your Spotlight. Download the Ring app. The app walks you through setting up and managing your Spotlight. Search for Ring in one of these app stores, or visit: ring.com/app Download from Windows Store 2 02_Spotlight_MANUAL.indd 3 Set up your Ring Beams Bridge. The Bridge connects your Ring Beams lights to the rest of your Ring system. To set up your Bridge, follow the instructions in the Ring app or Bridge user manual. If you do not own a Bridge, dont worry. Your Spotlight will work fine, but you wont be able to control it in the app. 3 9/28/18 4:19 PM Insert the batteries. Twist and pull off the front of the light, then press the side buttons on the battery compartment to open. Insert four D-Cell batteries, then slide the battery cover back onto your Spotlight. 4 02_Spotlight_MANUAL.indd 5 Set up your Spotlight in the Ring app. In the app, tap Set Up a Device. When prompted, select Beams and follow the in-app instructions. Doorbells Security Cams Chimes Beams Alarm 5 9/28/18 4:19 PM 2. Install your Spotlight. Loosen the locking screw on the base and remove the base from your Spotlight. Use the base as a template to mark the screw holes. Your Spotlight detects motion best when mounted 8-12 feet above the ground. 6 02_Spotlight_MANUAL.indd 7 Hold the base against the surface and drive the three mounting screws. Insert your Spotlight into the base at your chosen angle and tighten the screw. Loosen the side screw on your Spotlight, rotate to desired angle, and tighten the screw. 7 9/28/18 4:19 PM For additional help, visit: ring.com/help Or give us a call US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents 2018 Ring LLC or its affiliates. RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates. Last updated: 09/28/18 02_Spotlight_MANUAL.indd 8 9/28/18 4:19 PM Warnings This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Opera-

tion is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. de moin de 20 cm. Installer les antennes de facon ce que le personnel ne puisse approcher 20 cm ou moins de la position centrale de l antenne. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. La FCC des ltats-unis stipule que cet appareil doit tre en tout temps loign dau moins 20 cm des personnes pendant son functionnement. MPE Reminding To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installes doivent tre situes de facon ce que la population ne puisse y tre expose une distance

Sample Agency Request Letter Authority to Act as Agent Date: 28 November 2019 TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern:

I appoint TUV Rheinland (Shenzhen) Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with Ring LLC / 1523 26th Street, Santa Monica, California 90404, United States For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date:

2020/11/20

(Signature) Carro Hsieh

(Print Name) Engineer Telephone

+1 (800) 656-1918 On behalf of

Ring LLC

(Company Name) Page 1 of 1 Revision 0 By Title

QF094234

Ring 1523 26th Street Santa Monica CA 90404 USA 2020/09/10 FCC C2PC / ISED C3PC Permissive change letter Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Certification and Engineering Bureau ISED Canada 3701 Carling Avenue (Building 94) Ottawa, Ontario K2H 8S2 To whom it may concern, We, Ring LLC. apply for certification of the below described changes to the following existing certifications:

FCC-ID: 2AEUPBHAPB001, initial grant data: 2019-01-01 IC: 20271-BHAPB001, HVIN: 5LP1Y8, approval date: 2019-02-27 under FCC Class 2 Permissive Change rules according to FCC 2.1043 (b)(2) and ISED Class 3 Permissive Change rules according to ISED RSP-100, issue 12, section 10. For ISED, the updated products will be identified with the following dedicated FVIN:

1.7.16-56 (IC ID and HVIN remain unchanged). The purpose of this application is to add the following hopping modes by SW activation, to the existing initial certification which was for non-hopping mode (DTS) only:

LoRa DTS 500KHz 902.5-926.5MHz(Channel Separation:800KHz)---31channels LoRa FHSS 125KHz 902.2-927.8MHz(Channel Separation:200KHz)---129channels FSK FHSS 50Kbps 902.2-927.8MHz(Channel Separation:200KHz)---129channels FSK FHSS 150Kbps 902.4-927.6MHz(Channel Separation:400KHz)---64channels FSK FHSS 250Kbps 902.5-927.5MHz(Channel Separation:500KHz)---51channels Ring 1523 26th Street Santa Monica CA 90404 USA In addition, we introduce the following HW modification for further production units. HW modification:

(1) CC3 and CC4 changed from 12pF to Not Connect (Remove SX1262 32MHz crystal load capacitors) In SX1262 datasheet explain this:

The SX1261/2 does not require the user to set external foot capacitors on the XTAL supplying the 32 MHz clock. Indeed, the device is fitted with internal programmable capacitors connected independently to the pins XTA and XTB of the device. Ongoing compliance with all limits according to FCC 15.247 and ISED RSS-247 issue 2 for non-hopping and hopping modes has been verified by testing in accredited and recognized laboratories of TV Rheinland (Shenzhen) Co., Ltd. and is documented in related test reports, as listed below:

Test Report number 50351183 001 We confirm, that all changes are within the boundaries of the FCC C2PC and ISED C3PC rules. Sincerely, Carro Hsieh Engineer Hand signed signature Printed name title Company name and address Ring LLC 1523 26th St, Santa Monica, CA 90404, USA