User Guide
Doorbell Wired
Included hardware.
Find your doorbell chime.
Bag Hardware
A
B
C
3x Mounting Screws
3x Wall Anchors
2x Security Screws
1x Jumper Cable
2x Wire Extenders
2x Wire Nuts
Your Doorbell Wired is
designed to replace an
existing doorbell button,
and gets its power from the
doorbell system.
Ring your existing doorbell
and listen for the chime. If it
rings, we know your existing
doorbell system is working.
Follow the sound to find your
chime and make a mental
note of the location. We’ll
return to your chime soon.
Don’t have an existing
doorbell? You can power
your Doorbell Wired Pro
directly using our Plug-in
Adapter. Visit ring.com/
accessories to learn more.
2
3
Turn off power
at the breaker.
Grab the included
Jumper Cable.
This is essential to
keeping you and your
new Ring Doorbell safe.
If you’re not sure which
breaker controls your
doorbell chime, turn off the
master breaker for your home,
or contact an electrician.
The Jumper Cable bypasses
and disables your existing
doorbell chime, and must be
installed before you install
your Ring Doorbell.
Your Doorbell Wired is
compatible with doorbell
systems supplying 8–24 volts
AC, at 50 or 60Hz, 40VA max.
You’ll be working with
electrical wires during
the install process. If you
are uncomfortable or
inexperienced with
doing so, consult with a
licensed electrician.
4
5
Remove the cover from your
doorbell chime.
After you’ve located your
doorbell chime and turned off
power at the breaker, remove
the cover from your chime
and set it aside for now.
Connect the Jumper Cable.
Connect one end of the
Jumper Cable to the “Front”
terminal, and the other to the
“Trans” terminal. It doesn’t
matter which wire you
connect to which terminal.
Then re-tighten the
terminal screws.
Loosen the “Front” and
“Trans” terminal screws.
Make sure to keep the existing
doorbell wires in place.
6
7
Mark the screw holes.
Using your Ring Doorbell as
a template, mark the location
of the two mounting holes on
your wall.
Uninstall your existing
doorbell button.
Remove your doorbell from
the wall.
Disconnect the wires. Make
sure they don’t fall back inside
your wall so you can access
them later.
Remove the faceplate.
Grasp the bottom of the
faceplate and pull to remove.
8
9
Install the anchors.
(optional)
On stucco, brick, or concrete,
use a ¼" masonry bit to drill
holes in your wall, then insert
the included wall anchors.
(If you’re installing on wood or
siding, you can skip this step.)
Connect the doorbell wires.
Loop one doorbell wire
around each of the screw
terminals on the rear of your
Ring Doorbell then tighten
the terminals to secure.
If your doorbell wires are too
short to reach your new Ring
Doorbell, you can attach the
included wire extenders using
the included wire nuts.
10
11
Screw in your
Ring Doorbell.
Restore power
at the breaker.
It may take a moment for your
Ring Doorbell to power on.
You’ll know it’s ready once it
lights up and speaks to you.
Mount your Ring Doorbell
with the two included
mounting screws.
Be sure to feed any excess
wiring back into the wall first.
If you used the wire nuts, push
them through the hole as well.
DO NOT USE
any screw other than the
included long mounting
screws when securing
your Ring Doorbell.
Mounting
screw
Security
screw
12
13
Download the Ring App.
Secure your Ring Doorbell.
The Ring App walks you
through setting up and
managing your Ring Doorbell.
Search for “Ring” in one of the
app stores below, or visit
ring.com/app
Re-attach the faceplate, then
use the included screwdriver
to drive the small security
screw into the bottom of
your Ring Doorbell.
DO NOT USE
any screw other than the
included short security
screw when securing your
Ring Doorbell.
Set up your Ring Doorbell.
In the Ring app, select Set
Up a Device and follow the
in-app instructions.
Mounting
screw
Security
screw
14
15
Review, share
and download.
Your new device comes
with a free 30-day trial
of Ring Protect video
recording service.
To continue your subscription
and save your videos, please
visit ring.com/protect-plans
What is Ring Protect?
Ring Protect is a subscription
service that stores videos
from your Ring devices.
Why do I want it?
Ring lets you interact with
visitors and monitor your
property in real time, while
Ring Protect allows you
review and share those
videos anytime.
How much does it cost?
Ring Protect Basic covers
one Ring device for $3 USD/
month or $30 USD/year.*
Ring Protect Plus covers all
Ring devices at one property,
and costs $10 USD/month or
$100 USD/year.**
How do I sign up?
Simply log into your Ring
account at ring.com/protect-
plans, and follow the on-
screen instructions.
*$5 CAD per month or $50 CAD per year
**$15 CAD per month or $150 CAD per year
For additional help, visit
ring.com/help
Or give us a call:
US 1 800 656 1918
Canada 1 855 300 7289
Worldwide +1 310 929 7085
For a list of all our customer
support numbers, visit
ring.com/callus
For information on our warranty, theft
© 2020 Ring LLC or its affiliates.
protection, and Ring Protect Plans, see
Ring and all related marks are trademarks
ring.com/legal
of Ring LLC or its affiliates.
xx-xxxxxx-xx
Quick Start
1. Open the Ring app and
select Set Up Device.
Then follow the
in-app instructions.
2. Scan this code.
This identifies your
Ring device to make
setup fast and easy.
QR+FR
For additional help, visit
ring.com/help
5mm7mmxx-xxxxxx-xx
Important
Product
Information
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 1
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 1
11/10/20 12:14 PM
11/10/20 12:14 PM
IMPORTANT PRODUCT
INFORMATION
SAFETY INFORMATION: FAILURE
TO FOLLOW THESE SAFETY
INSTRUCTIONS COULD RESULT IN
FIRE, ELECTRIC SHOCK, OR OTHER
INJURY OR DAMAGE.
Your device can withstand outdoor use and
has been tested to withstand water projected
through a 6.3mm nozzle at a volume of 12.5 liters
per minute and a pressure of 30 kPa at a distance
of 3 meters for at least 3 minutes. However, your
device is not intended for underwater use. To
protect against electric shock, do not intention-
ally submerge or immerse your device, battery, or
adapter (not included) in water or expose your
device or adapter to other liquids. Do not spill
any food or beverages on your device, battery, or
adapter. Do not attempt to clean or polish your
device, battery, or adapter with or expose your
device, battery, or adapter to oil, lotion, or other
abrasive substances. Do not expose your device,
battery, or adapter to salt water or other conduc-
tive liquids. Do not expose your device, battery, or
adapter to pressurized water, high velocity water,
or extremely humid conditions (such as a steam
room). If your device, battery, or adapter gets wet,
carefully unplug all cables without getting your
hands wet and wait for it to dry completely before
plugging it in again. Do not attempt to dry your
device, battery, or adapter with an external heat
source, such as a microwave oven or a hair dryer.
To avoid risk of electric shock, do not touch your
device, battery, or adapter or any wires connected
to your device during a lightning storm while
your device, battery, or adapter is plugged in. If
your device, battery, or adapter appears to be
damaged, discontinue use immediately.
Protect your device from direct sunlight. Install
the device at dry locations and protect it against
rain and humidity.
Use only accessories supplied with your device, or
specifically marketed for use with your device, to
power your device. Use of third-party accessories
may impact your device’s performance. In limited
circumstances, use of third-party accessories may
void your device’s limited warranty. In addition,
use of incompatible third party accessories may
cause damage to your device or the third-party
accessory. Read all safety instructions for any
accessories before using with your device.
Protect the device from direct sunlight. Install the
device at dry locations and protect it against rain
and humidity. The device may not get contact
to salt water or other conductive liquids. The
device must be charged only within a building
in a dry state.
SAFELY CONNECTING YOUR RING
VIDEO DOORBELL WIRED TO YOUR
HOME’S ELECTRICAL WIRING
If you install the Ring Video Doorbell Wired where
a doorbell is already in use and you connect the
Ring Video Doorbell Wired to your home’s door-
bell electrical wiring, you must turn off the exist-
ing doorbell’s power source at your home’s circuit
breaker or fuse and test that the power is off
BEFORE removing the existing doorbell, install-
ing the Ring Video Doorbell Wired, or touching
electrical wires. Failure to turn off circuit breaker
or fuse so could result in FIRE, ELECTRIC SHOCK,
or OTHER INJURY or DAMAGE.
More than one disconnect switch may be
required to turn off the equipment before
servicing.
To test whether you have successfully de-ener-
gized your existing doorbell’s power source,
press your doorbell several times to confirm that
the power is off.
If the electrical wiring in your home does not
resemble any of the diagrams or instructions
provided with Ring Video Doorbell Wired, if you
encounter damaged or unsafe wiring, or if you
are unsure or uncomfortable in performing this
installation or handling electrical wiring, please
consult a qualified electrician in your area.
Only use accessories & power sources with L.P.S.
or PS2 certification that are recommended by
the manufacturer. Use of third-party accessories
may lead to damage to your Ring Video Doorbell
Wired or the accessory and may cause fire, elec-
tric shock, or injury.
Product Specifications
Device Name: Video Doorbell Wired
Model Number: 5AT3T5
Electrical Rating: 10–24 VAC or 24VDC
Temperature Rating: -5°F to 120°F (-20°C
to 50°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 3
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 3
11/10/20 12:14 PM
11/10/20 12:14 PM
devices is regulated. Make sure you dispose of,
or recycle, your device in accordance with your
local laws and regulations. For information about
recycling your device, go to www.amazon.com/
devicesupport.
Terms of Service and Warranty
By purchasing or using the product, you agree to
the Terms of Service found at ring.com/terms.
For information on our warranty, theft protection,
and Ring Protect Plans, see ring.com/legal
For Consumers in the USA
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a resi-
dential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
Pursuant to Section 15.21 of the FCC rules,
changes or modifications to a Product by the
user that are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
The device meets the FCC Radio Frequency Emis-
sion Guidelines. Information on the product is on
file with the FCC and can be found by inputting
such Product’s FCC ID (which can be found on the
device) into the FCC ID Search form available at
https://www.fcc.gov/oet/ea/fccid.
The party responsible for FCC compliance is:
Ring LLC, 1523 26th St, Santa Monica, CA USA,
90404
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure
limits set forth for an uncontrolled environment
and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and
operated in accordance with provided instruc-
tions and the antenna(s) used for this transmit-
ter must be installed to provide a separation
distance of at least 20 cm from all persons and
must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
End-users and installers must be provided with
antenna installation instructions and consider
removing the no-collocation statement.
For Consumers in Canada
This device contains licence-exempt transmit-
ter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
Information Regarding Exposure
to Radio Frequency Energy
This equipment complies with IC RSS-102 RF
exposure limits set forth for an uncontrolled
environment.
Radio Frequency Compliance
In order to protect human health, this device
meets the thresholds for exposure of the general
public to electromagnetic fields according to
Council Recommendation 1999/519/EC.
This transmitter must not be co-located or oper-
ating in conjunction with any other antenna or
transmitter. This equipment should be installed
and operated with a minimum distance of 20
centimeters between the radiator and your body.
Your Ring Video Doorbell Wired is designed to
replace an existing doorbell button, and gets its
power from the doorbell system.
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 4-5
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 4-5
11/10/20 12:14 PM
11/10/20 12:14 PM
1523 26th St.
Santa Monica, CA 90404
© 2020 Ring LLC or its affiliates.
Ring and all related marks are trademarks
of Ring LLC or its affiliates.
xx-xxxxxx-xx
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 6
Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH.indd 6
11/10/20 12:14 PM
11/10/20 12:14 PM