FCC ID: SK6-XDR240 Wireless Access Point Radio module

XA4 Series High Density Access Points Quick Installation Guide For XA4 Models XA4 Series High Density Convention Center Access Points (CCAPs) are plenum-

rated indoor APs using external antennas. With four 802.11ac Wave 2 radios, a powerful intelligence, automated provisioning, and optional cloud management, the APs deliver robust wireless connectivity in areas of medium to high user density. The XA4-240 has four 4x4 Wave 2 802.11ac radios: Radio IAP1 is a dual-band 2.4GHz/5GHz radio, and IAP2 through IAP4 are single-band 5GHz radios. This Guide covers the steps required to install and start the AP. For detailed configuration information, see the Xirrus Wireless Access Point User's Guide. integrated controller, application-level 1 You Need the Following Items Accessory Kit (included in each AP carton) includes Mounting bracket Xirrus-recommended antennas (and cables if needed) for up to four radios. Network designers should specify how many antennas to install for each radio. See the table below and Install Antennas on page 3 to see what connectors to use, based on the number of antennas allocated to a radio. Cables (if needed) are low-loss coaxial cables terminated with RP-SMA connectors. ??OK?? If you are not using recommended antennas, the XA4s output power setting must be reduced by 1 dB for every dB above 6dBi gain the selected antenna may produce. ??OK??

# Antenna Connectors to Use

... For Usage Scenario

(Configured settings) Connector 1 Connector 2 Connector 3 Connector 4 2 3 4 2x2 3x3; or 2x2 plus DFS*

4x4 (default ??OK??);

or 3x3 plus DFS*

Yes Yes Yes No Yes Yes No No Yes Yes Yes Yes DFS*: Zero-wait DFS (dynamic frequency selection) uses a dedicated antenna to provide fast frequency selection. This enables better use of 5GHz Wi-Fi channels. Power and Ethernet connection(s) to your wired network using Cat 5e/6 cables. The AP has 2 Ethernet ports:

GIG1/PoEThis 2.5 Gigabit port powers the AP via Power over Ethernet (PoE) using a Cat 5e or Cat 6 cable that also carries data traffic. See below for Power details. Note that the ports rate is set by auto-

negotiation with the switch.

(Optional) GIG2Connection to this second, data-only one-gigabit port provides additional bandwidth. Use Cat 5E or Cat 6 cable. AP must be connected to PoE networks without routing cabling to the outside plant. This ensures that cabling is not exposed to lightning strikes or possible crossover from high voltage lines. AP, PoE Injectors, or Switches must be installed and used indoors. The total Cat 5e or Cat 6 cable length from the switch to the AP must be no more than 100 m, including all cable segments. 1 XA4 Series High Density Access Points Power See the matrix below to select a compatible PoE switch or Xirrus-supplied injector for your AP. If using an injector, you must provide a data connection from the switch to the injector as well as another cable from the injector's OUT port to the APs GIGABIT1/PoE port. PoE injectors require an AC outlet. AP Model C o n s u m p t i o n P o w e r i M a x m u m

(

8 0 2 3 a t

)

. P o E S w i t c h G e n e r i c P o E S w i t c h X i r r u s XA4-240 38W

(Ports 1-12 only) X P 1

-

M S I

-

3 0 X P 1

-

M S I

-

7 5 M

(

P O E

-

7 5 U

-

1 U P X

-

) X P 1

-

M S I

-

7 5 X P 8

-

M S I

-

7 0 M X P 2

-

M S I

-

9 5 M Apply power to GIG1/POE port onlyother AP Gigabit ports will not draw power if connected to a powered switch port, and AP LEDs will not light. Workstation with a Web browser to configure the AP via the Xirrus Management System or directly via the APs Windows Management Interface (WMI). NOTE: Leave protective plastic film on the AP until installation is complete, to avoid leaving marks on the AP. Direct Ceiling Mountuse the furnished mounting plate with four user-supplied screws that are appropriate for the construction type of the mounting site. The AP attaches to the mounting plate with four keyhole studs that are pre-installed on the back of the AP. 2 Choose a Suitable Location Choose an indoor location that is central to your users, and that is away from heat sources. The location must be capable of supporting the weight of the AP and the mounting bracket (about 5?? lb total). For optimal placement, we recommend that a predictive survey be performed by a qualified Xirrus partner. Maintain a distance of at least 50 feet between additional APs. Keep the unit away from electrical devices or appliances that generate RF noise-at least 3 to 6 ft (1m - 2m). To ensure good air flow, it is essential that the APs vents are not blocked. The XA4 can operate from a Wireless Distribution System (WDS) link. However, the unit must be configured via the Ethernet connection prior to mounting and power must be supplied via the GIG1 Ethernet connector. 2 XA4 Series High Density Access Points 3 Install Mounting HardwareCeiling Mount The following steps use a mounting plate, which offers a secure mount and ease of dismount. 1. Use the AP mounting plate to mark the placement on the ceiling of the cable feed opening and of the 4 mounting slots. 2. Drill and prepare holes for user-supplied screws as appropriate. 3. Cut an access hole for the cable(s) in the ceiling and draw enough cable through to attach to the AP when it is installed. 4. Align the mounting plate over the prepared holes (position the edges with the mounting slots flush against the wall.). Feed the cable(s) through. Secure the plate with the screws. 4 Mounting slots Cable feed AP attachment keyhole slots Mounting slots Install Antennas See the Xirrus External Antenna Guide for recommended antennas. Check the network plan for the number of antennas to connect to each of the four radios, named IAP1 to IAP4. The table on page 1 shows which connector numbers to use, and the image at right shows their numbering. For Rubber Duck Antennas:

Install the antennas on the AP at the locations described above. Antenna Connectors For Panel Antennas:

Install your antenna(s) as directed by the manufacturer. Note that radio IAP1 is dual-band, so if you use single-

band antennas for it, you must configure IAP1 to the antennas band (2.4 GHz or 5.0 GHz). See Zero-Touch Provisioning and Ongoing Management on page 4). Use low-loss coaxial cables compatible with the XA4s RP-SMA connectors. Note that some antennas include integrated cables as part of the unit, and these do not need separate cables. 3 XA4 Series High Density Access Points 5 Connect Cables and Install AP NOTE: Once you connect GIG1/POE, an automatic upgrade typically starts soon after the AP has Internet connectivity. Do not unplug this port during the upgrade or the AP may become inoperable. The upgrade should take 10 minutes or less. 1. Connect the cable that carries power and data to GIG1/PoE (shown in red). If you use a Xirrus-supplied injector, its CONNECT LED should light (for 70W and higher injectors, it is OK if it blinks). If power is being properly supplied, the APs LEDs will light and then commence blinking in their rotating boot pattern. A second data connection may be plugged into GIG2 (optional). If using panel antennas, connect the cables as indicated in the table on page 1. 2. POE Alignment Line on AP Alignment Lines on Alignment Lines on Lock/Unlock Lever Lock/Unlock Lever Installed AP Lock/Unlock Lever 3. Mount the AP: Position the keyhole studs on the back of the AP over the keyhole slots on the mounting plate using the following aidline up the alignment line on the AP (small bump located on the AP as indicated above) with the vertical line on the lock lever. 4. Push the AP against the mounting plate and slide the AP towards the locking lever until the keyhole slugs are secure in the slots and the lever locks in place. The edge of the AP will line up with the horizontal line on the lock lever. If you need to remove the AP, push down on the lock lever to unlock the AP. Continue to hold it down while you slide the AP away from the lever and pull the AP off the mounting plate. 5. 6 Zero-Touch Provisioning and Ongoing Management Most customers use the Xirrus Management System (XMS) for the initial setup and continuing management of Xirrus APs. XMS users set up new APs for zero-touch provisioning via the following platforms. Wait five minutes after powering up the AP to automatically discover it, then use XMS to view and manage it. Newly discovered APs are automatically assigned to the XMS default profile, and receive the configuration defined for that profile. XMS-Cloudperforms zero-touch provisioning. Your new APs appear in XMS even before you receive your equipment. When the email arrives with your login information, use XMS-Cloud to specify the initial settings for your APs. A Guided Tour will walk you through the basic steps of creating a profile containing 4 configuration settings, including creating SSIDs and firewall/application control rules. Once the installed AP has Internet connectivity, it will automatically contact Xirrus for cloud-based zero-touch provisioning per your settings, install the latest applicable license, and upgrade the AP to the latest software version as appropriate. XMS-Enterprisedetects and provisions new Xirrus devices deployed in your network. Create and configure a default profile for newly added APs, then set up discovery for the APs subnetwork. New devices will automatically receive the configuration defined in the default profile. If you are not using XMS, please see the Xirrus Wireless AP User's Guide to configure the AP manually via the Express Setup menu. The User Guide is available from http://support.xirrus.com (login required). Select the Libraries tab and click the ArrayOS - XR Platform Latest Release link. 7 Using the Reset Button The reset button returns the AP to factory default settings while rebooting. It is located on the bottom of the AP, just above the serial number/bar code. Use the reset button as follows:

Unplug the cable from the GIG1/PoE port. Press the reset button all the way (there should be a faint click) and hold it. Plug the cable back in and continue to keep the button pressed for 10 seconds. This triggers the factory default reset during the boot process. 201 Xirrus, Inc. All Rights Reserved. The Xirrus logo is a registered trademark of Xirrus, Inc. All other trademarks are the property of their respective owners. Content subject to change without notice. 812-0085-013 Rev A 1.800.947.7871 Toll Free in the US

+1.805.262.1600 Sales

+1.805.262.1601 Fax 2101 Corporate Center Drive Thousand Oaks, CA 91320, USA To learn more visit:

xirrus.com or email info@xirrus.com Wireless Access Point Appendix C: Notices (XA, XD and XR500/

600 Series Only) This Appendix contains Notices, Warnings, and Compliance information for the XA, XD and XR500/600 Series only. For Notices, Warnings, and Compliance information for outdoor products, please see the Quick Installation Guide for that product. For Notices, Warnings, and Compliance information for XR-320 and X2-120, please see the X2 and XR300 Series Notices and Regulatory Guide. For Notices, Warnings, and Compliance information for all other APs, please see Notices (XR-1000 to XR-6000 Indoor Models) on page 571. This appendix contains the following information:

Notices on page 553 EU Directive 1999/5/EC Compliance Information on page 562 Compliance Information (Non-EU) on page 569 Safety Warnings on page 570 Translated Safety Warnings on page 571 Software License and Product Warranty Agreement on page 572 Hardware Warranty Agreement on page 572 Notices Wi-Fi Alliance Certification www.wi-fi.org 553 Wireless Access Point FCC Notice for XD4-240 (XD4240) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. instruction manual, may cause harmful FCC Notice for All Other Devices Covered by This Appendix This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate RF energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following safety measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced wireless technician for help. For All Devices Covered by This Appendix The rest of the information in this Appendix applies to all Xirrus XA, XD and XR500/600 Series APs, except as noted. 554 Wireless Access Point

!

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules, with operation subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause unwanted operation. For all models available in the USA/Canada market, only channels 1~11 can be operated in the 2.4GHz band. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-

transmitter product procedures. This device is restricted for indoor use. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE: FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To ensure compliance with FCC and Industry Canada RF exposure requirements, this device must be installed in a location where the antennas of the device will have a minimum distance of at least 30 cm (12 inches) from all persons, except that XD2 models must have a minimum distance of at least 20 cm (8 inches) from all persons, and the antennas of XA4 models must have a minimum distance of at least 34 cm (13.6 inches) from all persons. Using higher gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter. High Power Radars High power radars are allocated as primary users (meaning they have priority) in the 5250MHz to 5350MHz and 5650MHz to 5850MHz bands. These radars could cause interference and/or damage to LE-LAN devices. 555 Wireless Access Point Non-Modification Statement Unauthorized changes or modifications to the device are not permitted. Use only the supplied internal antenna, or external antennas supplied by the manufacturer. Modifications to the device will void the warranty and may violate FCC regulations. Cable Runs for Power over Ethernet (PoE) The AP must be connected to PoE networks without routing cabling to the outside plant this ensures that cabling is not exposed to lightning strikes or possible cross over from high voltage. Battery Warning

! Caution! The AP contains a battery which is not to be replaced by the customer. Danger of Explosion exists if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. UL Statement Use only with listed ITE product. Industry Canada Statement (XA, XD Series) This device complies with Industry Canada license-exempt RSS standards (RSS 247), and standards for Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and License-Exempt Local Area Network (LE-LAN) Devices. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. 556 Wireless Access Point Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-

transmitter product procedures. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz Slection dynamique de frquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. For indoor use only. Pour une utilisation en intrieur uniquement. IMPORTANT NOTES (XA, XD Series):

IC Radiation Exposure Statement:

To ensure compliance with Industry Canada RF exposure requirements, this device must be installed in a location where the antennas of XD Series devices will have a minimum distance of at least 30 cm (12 inches) from all persons; for XA4 models the minimum distance from antennas is 34 cm (13.6 inches). Using higher 557 Wireless Access Point gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter. Installez l'appareil en veillant conserver une distance d'au moins 30 cm (pour XA4: 34 cm) entre les lments rayonnants et les personnes. Cet avertissement de scurit est conforme aux limites d'exposition dfinies par la norme CNR-102 at relative aux frquences radio. External Antennas (for XA4 only) This radio transmitter (IC: 5428A - XDR240, IC: 5428A - XDR241) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 5428A - XDR240, IC: 5428A - XDR241) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. IC: 5428A - XDR240 Ant. Brand Model Name

(P/N) Antenna Type Connector Gain (dBi) 2.4GHz 5GHz 1 2 WNC EW2458-02 Laird PDQ24499 Dipole Antenna Reversed-

SMA Directional Antenna Reversed-

SMA 2 8.6 3 9.4 558 Wireless Access Point IC: 5428A - XDR241 Ant. Brand Model Name

(P/N) Antenna Type Connector 1 2 WNC EW2458-02 Laird PDQ24499 Dipole Antenna Directional Antenna Reversed-SMA Reversed-SMA Gain (dBi) 5GHz 3 9.4 The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. Le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 doit se conformer la limite de p.i.r.e. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. Le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer la limite de p.i.r.e. spcifie pour l'exploitation point point et non point point, selon le cas. 559 Wireless Access Point Industry Canada Statement (except for XA4 and XD Series) This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. When operating the XR-600 Series in the band 5250-5350 MHz with a maximum e.i.r.p. greater than 200 mW in Canada, please adjust antenna/EUT to comply with the following e.i.r.p. elevation mask, where is the angle above the local horizontal plane (of the Earth) as shown below:

(i) -13 dB(W/MHz) for 0 < 8

(ii) -13 - 0.716 (-8) dB(W/MHz) for 8 < 40

(iii) -35.9 - 1.22 (-40) dB(W/MHz) for 40 45

(iv) -42 dB(W/MHz) for > 45 Avertissement:

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour 560 Wireless Access Point les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. IMPORTANT NOTE (Series other than XA and XD):

IC Radiation Exposure Statement:

To ensure compliance with Industry Canada RF exposure requirements, this device must be installed in a location where the antennas of the device will have a minimum distance of at least 30 cm (12 inches) from all persons. Using higher gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter. Installez l'appareil en veillant conserver une distance d'au moins 30 cm entre les lments rayonnants et les personnes. Cet avertissement de scurit est conforme aux limites d'exposition dfinies par la norme CNR-102 at relative aux frquences radio. 561 Wireless Access Point EU Directive 1999/5/EC Compliance Information This Appendix contains Notices, Warnings, and Compliance information for the XA, XD and XR500/600 Series only. For other models, see the notes at the beginning of this appendix. This section contains compliance information for the Xirrus Wireless AP family of products. The compliance information contained in this section is relevant to the European Union and other countries that have implemented the EU Directive 1999/5/EC. Declaration of Conformity Cesky [Czech] Toto zahzeni je v souladu se zkladnimi poadavky a ostatnimi odpovidajcimi ustano veni mi Smrnice 1999/5/EC. Dansk [Danish] Dette udstyr er i overensstemmelse med de vsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF. Deutsch [German] Dieses Gerat entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtinie 1999/5/EU. Eesti [Estonian] See seande vastab direktiivi 1999/5/EU olulistele nuetele ja teistele as jakohastele stetele. English This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol [Spain] Este equipo cump le con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/

CE.

[Greek]

1999/5/EC. 562 Wireless Access Point Franais [French] Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC. slenska [Icelandic] etta tki er samkvmt grunnkrfum og rum vieigandi kvum Tilskipunar 1999/5/EC. Italiano [Italian] Questo apparato conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE. Latviski [Latvian] iekrta atbilst Direktvas 1999/5/EK btiskaj prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi [Lithuanian] is renginys tenkina 1995/5/EB Direktyvos ir kitas ios direktyvos esminius reikalavimus nuostatas. Nederlands [Dutch] Dit apparant voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1995/5/EC. Malti [Maltese] Dan l-apparant huwa konformi mal-htigiet essenzjali u l-provedimenti l-ohra rilevanti tad-Direttiva 1999/

5/EC. Margyar [Hungarian] Ez a kszlk teljesiti az alapvet kvetelmnyeket irnyelvben meghatrozott s ms 1999/5/EK vonatkoz rendelkezseket. Norsk [Norwegian] Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF. Polski [Polish] Urzdzenie jest zgodne z oglnymi wymaganiami oraz sczeglnymi mi warunkami okrelony mi Dyrektyw. UE:1999/5/EC. Portugus [Portuguese] Este equipamento est em conformidade com os requisitos essenciais e outras provises relevantes da Directiva 1999/5/EC. 563 Slovensko [Slovenian] Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi popoji Direktive 1999/5/EC. Wireless Access Point Slovensky [Slovak] Toto zariadenie so zkladnmi poadavkami a inmi prislunmi nariadeniami direktiv: 1999/5/EC. je v zhode Suomi [Finnish] Tm laite tytt direktiivin 1999/5//EY olennaiset vaatimukset ja on siin asetettujen muiden laitetta koskevien mrysten mukainen. Svenska [Swedish] Denna utrustning r i verensstmmelse med de vsentliga kraven och andra relevanta bestmmelser i Direktiv 1999/5/EC. Assessment Criteria The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC:

Radio: EN 301 893 and EN 300 328 (if applicable) EMC: EN 301 489-1 and EN 301 489-17 Safety: EN 60950, EN 62311 and EN 50385 CE Marking For the Xirrus Wireless AP, the CE mark and Class-2 identifier opposite are affixed to the equipment and its packaging:

Russian Certification Marking For the Xirrus XR-500, XR-520H, XR-2000, and XR-4000 Series Wireless APs, the approval mark is affixed to the equipment:

564 Wireless Access Point WEEE Compliance Natural resources were used in the production of this equipment. This equipment may contain hazardous substances that could impact the health of the environment. In order to avoid harm to the environment and consumption of natural resources, we encourage you to use appropriate take-back systems when disposing of this equipment. The appropriate take-back systems will reuse or recycle most of the materials of this equipment in a way that will not harm the environment. The crossed-out wheeled bin symbol

(in accordance with European Standard EN 50419) invites you to use those take-back systems and advises you not to combine the material with refuse destined for a land fill. If you need more information on collection, re-

use and recycling systems, please contact your local or regional waste administration. Please contact Xirrus for specific information on the environmental performance of our products. 565 Wireless Access Point National Restrictions In the majority of the EU and other European countries, the 2.4 GHz and 5 GHz bands have been made available for the use of Wireless LANs. The following table provides an overview of the regulatory requirements in general that are applicable for the 2.4 GHz and 5 GHz bands. Frequency Band (MHz) Max Power Level

(EIRP) (mW) Indoor Outdoor 24002483.5 52505350 *

54705725*

100 200 1000 X X X X **

N/A X

*Dynamic frequency selection and Transmit Power Control is required in these frequency bands.

**France is indoor use only in the upper end of the band. The requirements for any country may change at any time. Xirrus recommends that you check with local authorities for the current status of their national regulations for both 2.4 GHz and 5 GHz wireless LANs. The following countries have additional requirements or restrictions than those listed in the above table:

Belgium The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Xirrus recommends checking at www.bipt.be for more details. Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie www.bipt.be voor meer gegevens. 566 Wireless Access Point Les liasons sans fil pour une utilisation en extrieur dune distance suprieure 300 mters doivent tre notifies lInstitut Belge des services Postaux et des Tlcommunications (IBPT). Visitez www.bipt.be pour de plus amples dtails. Greece A license from EETT is required for the outdoor operation in the 5470 MHz to 5725 MHz band. Xirrus recommends checking www.eett.gr for more details. 54705725 z

, . www.eett.gr Italy This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owners property, its use requires a general authorization. Please check with www.communicazioni.it/it/ for more details. Questo prodotto conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato allinterno del proprio fondo, lutilizzo di prodotti wireless LAN richiede una autorizzazione Generale. Consultare www.communicazioni.it/it/ per maggiori dettagli. Norway, Switzerland and Liechtenstein Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries. Calculating the Maximum Output Power The regulatory limits for maximum output power are specified in EIRP (radiated power). The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector

(specified in dBm). 567 Wireless Access Point Integrated Antennas Xirrus Wireless APs (except for XA4 APs) employ integrated antennas that cannot be removed and which are not user accessible. Nevertheless, as regulatory limits are not the same throughout the EU, users may need to adjust the conducted power setting for the radio to meet the EIRP limits applicable in their country or region. Adjustments can be made from the products management interface either Web Management Interface (WMI) or Command Line Interface (CLI). External Antennas (for XA4 only) limits, the antennas for this product should be positioned no less than 34 cm from your body or nearby persons.

! WARNING: In order to comply with radio frequency (RF) exposure

! WARNING: Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54).

! To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power for successful

(EIRP) communication. that permitted is not more than Operating Frequency The operating frequency in a wireless LAN is determined by the access point. As such, it is important that the access point is correctly configured to meet the local regulations. See National Restrictions in this section for more information. If you still have questions regarding the compliance of Xirrus products or you cannot find the information you are looking for, please contact us at:

Xirrus, Inc. 2101 Corporate Center Drive 568 Wireless Access Point Thousand Oaks, CA 91320 USA Tel:

1.805.262.1600 1.800.947.7871 Toll Free in the US 1.866.462.3980 Fax:

www.xirrus.com Compliance Information (Non-EU) This Appendix contains Notices, Warnings, and Compliance information for the XA, XD and XR500/600 Series only. For other models, see the notes at the beginning of this appendix. This section contains compliance information for the Xirrus Wireless AP family of products. The compliance information contained in this section is relevant to the listed countries (outside of the European Union and other countries that have implemented the EU Directive 1999/5/EC). Declaration of ConformityBrazil For XR-500 Only 569 Declaration of Conformity Mexico XR-520: Dictamen #: 1402D00742 XR-600: Dictamen #: 1402CE08098 Wireless Access Point XR-520: Cofetel Cert #: RCPXIXR13-1003 Thailand This telecommunication equipment conforms to NTC technical requirement. Safety Warnings This Appendix contains Notices, Warnings, and Compliance information for the XA, XD and XR500/600 Series only. For other models, see the notes at the beginning of this appendix. Safety Warnings Read all user documentation before powering this device. All Xirrus interconnected equipment should be contained indoors. This product is not suitable for outdoor operation. Please verify the integrity of the system ground prior to installing Xirrus equipment. Additionally, verify that the ambient operating temperature does not exceed 50C

(40C for the XR500/600 Series). Circuit Breaker Warning The indoor wireless AP relies on the buildings installation for over current protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A (U.S.) or 240 VAC, 10A (International) is used on all current-carrying conductors.

!

!

570 Wireless Access Point

!

!

Explosive Device Proximity Warning Do not operate the wireless AP near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Lightning Activity Warning Do not work on the Wireless AP or connect or disconnect cables during periods of lightning activity. Translated safety warnings appear below. Translated Safety Warnings This Appendix contains Notices, Warnings, and Compliance information for the XA, XD and XR500/600 Series only. For other models, see the notes at the beginning of this appendix. Avertissements de Scurit

!

!

Scurit Lisez l'ensemble de la documentation utilisateur avant de mettre cet appareil sous tension. Tous les quipements Xirrus interconnects doivent tre installs en intrieur. Ce produit n'est pas conu pour tre utilis en extrieur. Veuillez vrifier l'intgrit de la terre du systme avant d'installer des quipements Xirrus. Vrifiez galement que la temprature de fonctionnement ambiante n'excde pas 50C (40C pour XR-520). Proximit d'appareils explosifs N'utilisez pas les Wireless APs proximit d'amorces non blindes ou dans un environnement explosif, moins que l'appareil n'ait t spcifiquement modifi pour un tel usage. 571 Wireless Access Point

!

!

Foudre N'utilisez pas les Wireless APs et ne branchez pas ou ne dbranchez pas de cbles en cas de foudre. Disjoncteur Les Wireless APs dpend de l'installation du btiment pour ce qui est de la protection contre les surintensits. Assurez-vous qu'un fusible ou qu'un disjoncteur de 120 Vca, 15 A (tats-Unis) ou de 240 Vca, 10 A

(International) maximum est utilis sur tous les conducteurs de courant. Software License and Product Warranty Agreement For Software License and Product Warranty information, please see http://

www.xirrus.com/support/eula/. Hardware Warranty Agreement For Hardware Warranty information, please see http://www.xirrus.com/

support/eula/. 572