A Quick Start Guide Guide de dmarrage rapide Gua de Inicio Rpido Overview WARNING: See safety information included with the device for warnings and precautions. To maximize battery life, plug in the navigation unit for the rst 2 hours of use. Always make sure your GPS has a clear view of the sky. The rst time you use the device, it may take up to 15 minutes for your GPS to connect to the satellites. TO POWER THE DEVICE:
On Press and hold the Power Key for two (2) seconds.
(Device powers on in 5 seconds.) Press and hold the Power Key for ve (5) seconds. Off BATTERY POWER INDICATOR:
No Light Device is running on the battery. Battery power is sufcient. Device is plugged in and the battery is fully charged. Device is plugged in and the battery is charging. Green Red IMPORTANT: Connect your device to your personal computer to register your device and activate additional features. Features require Internet connection. FOR CUSTOMER SUPPORT, CALL 800-333-0136 1 Power Key Battery Power Indicator PHOTO TO COME 2 NOTE: Use the Reset button (located on the side of the device) to restore factory settings and restart the device. Install the Mount NOTE: Follow all local regulations governing the placement of the mount. Select an area with a line of sight to the sky and GPS satellites to ensure reliable GPS information. 1. 2. 3. 4. 5. 6. 7. 8. 9. Clean and dry the mounting area. Remove the suction cup protective lm. Adjust the angle of the mount using the thumbscrew. Pull the suction cup lever up to release suction. Place and hold the mount suction cup against the mounting surface. Press the suction cup lever down until it snaps into place. Slide the device onto the mount. Plug the power cord into the device and the vehicles 12-volt power source. Adjust the device so that it can be easily seen and does not block the drivers line of sight. 3 Main Menu 1 Enter truck information and access truck-specic use tools. Show location on the map and view navigation instructions. Change driver status. Choose a destination. Select TND and route preferences. 2 3 4 5 6 Mute/unmute the speaker. 7 Adjust speaker volume. Select the trailer load option. Indicates power status. 8 9 1 5 9 2 8 3 4 6 7 NOTE: From other screens, tap this icon in the bottom right corner to return to the Main Menu. 4 Enter Truck Information and Set Warnings 1. 2. 3. 4. 5. Tap Truck Tools > Truck Info or Warnings. Tap Tap the option button to be changed. Enter new settings. Tap Back to save changes. On the left, tap on an option to view all options. and NOTE: See page 15 for Routing Options. Route to a Destination Address 1. 2. Tap Choose Destination > New Location. Tap Address. On the right, enter settings for the option 5 Route to a Destination (Continued) 3. Enter the name of the city. (Note: As you type, the keyboard displays only the next possible letter. Prompts appear in the top bar. Tap the name to select. Or, tap List to view cities beginning with the letter(s) you entered. You can also use Zip Code Search.) Enter the street name. (Note: Tap Expand Search to?) Enter the house number. (Note: Tap ABC to enter letters.) 4. 5. See Conrm Destination Window (page 7). City Center -To route to a city without an address, tap Choose Destination > New Location > City Center. See instructions above. Intersection -To route to the intersection of two streets, tap Choose Destination > New Location > Intersection. See instructions above. Latitude/Longitude -To enter a location by latitude and longitude, tap Choose Destination > New Location > Enter Lat/Long. History -Recent destinations are stored in History. Tap Choose Destination > History to view. Address Book -To save a location, enter it in the Address Book from the Conrm Destination Window (page 7). 6 Conrm Destination Window 1 Destination address. Begin route to destination. Cross reference to printed Rand McNally Motor Carriers Road Atlas. Return to previous window. View the map. Change the starting address for a route to the location displayed on the map screen. Return to Main Menu. Save the location to the Address Book. Add the location as a via point on the way to a previously entered destination. 4 2 3 4 5 6 7 8 9 1 6 3 5 2 9 8 7 7 Find a Point of Interest (POI) 1. 2. Tap Choose Destination > Points of Interest. Select a search type (My Truck, City, My Route, End of Day or Destination). Select a category and, if necessary, a subcategory. Tap on the Point of Interest in the displayed list. 3. 4. Google Search 1. 2. Tap Choose Destination > Google Search. 8 Repeat spoken next-maneuver instructions. Route Map Window 1 2 Name of street you will turn onto next. 3 4 5 6 7 8 Show arrival time and remaining distance. Directions list slideout. Zoom in/zoom out. Tap to view the Trafc Window. Current speed limit. Tap on the current speed to display the Virtual Dashboard. Additional current location or route options. 9 10 Tap to view current road name, upcoming cross road name, or city name and state. 11 Select a map display option (North Up, Heading Up or 3D View). 12 Return to Main Menu. 13 Slide out exit amenities. 14 Tap to view weather information. 9 Junction View When on a route, Junction View displays when you have an upcoming maneuver. Once past the maneuver, Junction View closes and the previous window displays. 1 The highway you are currently on. The highway you will be on after the next maneuver. 2 3 Number and direction of lanes for the next maneuver. 4 Miles to the upcoming maneuver. Distance decreases as you approach the ramp. Return to Route Map Window. 5 1 4 5 2 3 Trafc Window 1 Tap to select either a recalculated route based on trafc events or to stay on the current route. View trafc events along your route. View a list of trafc events within receiver range. Return to Route Map Window. Tap the Off/Predicted/Real-Time Trafc button to display Predicted Trafc. Real-Time Trafc is an optional service Additional accessory required. Return to Main Menu. 1 4 2 5 3 6 2 3 4 5 6 10 Weather 1. To view current weather information and the three-day forecast for your location, tap the Weather icon [show image?] on the Route Map Window. To view weather information at your destination, tap At Destination. [What about along the route?]
Tap Map Overlay to choose from different weather types to display on the map as you drive. Use the slider at the bottom left of the Weather Type screen to adjust the transparency of the overlay on the map. 2. 3. 4. 11 Virtual Dashboard When using the virtual dashboard on a route, the virtual dashboard closes and the Junction View displays an upcoming maneuver. Once past the maneuver, the virtual dashboard redisplays. 1 3 2 4 5 8 9 1 2 3 4 5 6 7 6 Current direction of travel. Displays current time at the yard, current location and your destination. Sunrise/Sunset time based on vehicle location (latitude/longitude) and day. Current speed (above) and posted speed limit (below). Altitude at current location. Percentage of current trip completed, distance to next maneuver, and the number of miles and time spent on the trip to this point. Average uphill and downhill speeds. Return to the Route Map Window. 12 10 7 11 8 9 Gather trip information for up to three trips. Includes odometer settings, hours, and speeds. 10 Reset trip information for the selected trip (Tab 1, Tab 2 or Tab 3). 11 Select to reset the information in all three tabs after the vehicle has remained stationary for the specied number of hours. 12 Tap to view fuel logs. 12 View Timers and Logs Countdown timers are controlled by the Driver Status (Driving, On Duty, or Off Duty) selected on the Main Menu. 1. 2. 3. 4. 5. Tap Truck Tools > Timers, Logs, Trails, Fuel. Tap Timers to view timers, odometer readings, and times. Tap on a eld to change or reset the number. Tap Logs to view a list of mileage logs by quarter. Tap on a quarter to view individual logs by state. 13 View Trails and Fuel 1. Tap Truck Tools > Timers, Logs, Trails, Fuel. Tap Set Trails to record a bread-crumb path of GPS coordinates where your truck has traveled. Tap any record to view the trail, edit the name or set the color. Tap Keep on Map to display the trail on the Route Map Window. Tap Fuel to view a list of fuel logs by quarter. Tap on a quarter to view individual logs by state. Tap Add Fuel to record the date, location and cost of fuel purchase. Tap on a eld to make changes. Tap Report to include the purchase in the fuel log. 8. 9. 10. Tap Save. 2. 3. 4. 5. 6. 7. 14 Set Routing and Device Options 1. 2. 3. 4. 5. 10. Tap Back to save changes and return to the Main Menu. Tap Preferences. Tap the Truck, Route or Device tab. Tap Tap the option button to be changed. Enter the new settings for the option. to view options. and On the left, tap on an option On the right, enter settings for the option 15 Warnings, Disclaimers and End-User License Agreement Pay attention to road conditions and street signs, and obey all trafc and safety laws. Trafc laws and current trafc conditions must always be observed and take precedence over the instructions issued by the TND product navigation system. The User should be aware of situations where current trafc conditions and the instructions from the navigation system may be in conict. Some states prohibit the use of windshield mounts and may otherwise restrict the usage of navigation and other electronic devices in the vehicle. It is the Users responsibility to ensure compliance with all laws and regulations. The use of the navigation system does not relieve the User of his/her responsibilities. The User is ultimately responsible for the vehicle under his/her control and should be aware of the surroundings at all times. If after reading these statements the User decides not to accept these terms, the User should not use the TND product. Rand McNally hereby grants you (User) a single-user non-exclusive, non-transferable license to use the Rand McNally IntelliRoute TND trucking navigation product (hereinafter referred to as the TND product (including software and associated data) ) for Users own internal business or personal use and not for resale, sublicense or commercial use. This TND product and the software incorporated in it and related documentation are furnished under license and may be used or copied only in accordance with this license. Except as permitted by such license, the contents of this TND product and software may not be disclosed to third parties, copied or duplicated in any form, in whole or in part, without the prior written permission of Rand McNally. This TND product and software contain proprietary and condential information of Rand McNally and its licensors. Rand McNally grants User a limited license for use of this TND product and the software incorporated in the TND product for its normal operation. By using the TND product, User acknowledges that the content of this document and the TND product are the property of Rand McNally and its licensors and are protected by U.S. copyright, trademark and patent laws and international treaties. THE USER MAY NOT:
product on a network or le server, time-sharing or to process data for other persons.
product to create any routing tables, les, databases or other compendiums.
product, its software or content.
product in any way, or decompile, disassemble, reverse engineer or reduce to human readable form the TND product and software incorporated therein.
product, its software or content. This license will terminate automatically if User fails to comply with any of the terms of this license and User agrees to stop using the TND product. Rand McNally may revise or update the TND product and is not obligated to furnish any revisions or updates to User. Rand McNally warrants that the TND product, and the component parts thereof, will be free of defects in workmanship and materials for a period of one (1) year from the date of rst consumer purchase. This warranty may be enforced by the rst consumer purchaser, provided that the product is utilized within the U.S.A. or Canada. Rand McNally will, without charge, repair or replace (with a new or newly reconditioned unit), at its option, defective TND products or component parts. For repair or replacement of defective TND products, User must contact Rand McNally at 1-800-333-0136 for return authorization and instructions. User will be required to provide proof of the date of rst consumer purchase, such as a duplicated copy of a sales receipt. The consumer must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Rand McNallys expense, if the product is repaired or replaced under warranty. Repairs or replacements have a 90-day warranty. If the unit sent in is still under its original warranty, then the new warranty is 90 days or to the end of the original one (1) year warranty, depending on which is longer. 18 This warranty gives the consumer specic rights, and he or she may also have other rights which vary from state to state. Exclusions: This limited warranty does not apply: 1) to any product damaged by accident; 2) in the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs; 3) if the serial number has been altered, defaced or removed; or 4) if the owner of the product resides outside of the U.S.A. or Canada. Caution: Rand McNally makes no warranty as to the accuracy of completeness of the information in the TND product and disclaims any and all express, implied or statutory warranties, including any implied warranty of merchantability or tness for a particular purpose. It is the users responsibility to use this product prudently. This product is intended to be used only as a travel aid and must not be used for any purpose requiring precise measurement of direction, distance, location or topography. RAND MCNALLY AND ITS LICENSORS DO NOT MAKE ANY OTHER WARRANTY OR REPRESENTATION, EITHER EXPRESS OR IMPLIED, WITH RESPECT TO THE TND PRODUCT, INCLUDING ANY WARRANTY AS TO QUALITY, PERFORMANCE, TITLE OR NON- INFRINGEMENT. IN NO EVENT WILL RAND MCNALLY OR ITS LICENSORS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE TND PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations my not apply to some consumers. The User agrees to allow User-provided information to Rand McNally to be used for internal business evaluation purposes, including, but not limited to, evaluating the effectiveness of the services provided, methods to simplify or improve User experiences. Such information will not be used by third parties or in any way that discloses the identity of the User. Rand McNally may make use of third party software in the TND product. Notwithstanding the terms and conditions of this license, use of some third party materials included in the TND product may be subject to other terms and conditions. The ofcial third party copyright notices are provided at the end of this License. The User agrees to indemnify, defend and hold Rand McNally and its licensors (including their respective licensors, suppliers, assignees, subsidiaries, afliated companies, and the respective ofcers, directors, employees, shareholders, agents and representatives of each of them) free and harmless from and against any liability, loss, injury (including injuries resulting in death), demand, action, cost, expense or claim of any kind or character, including but not limited to attorneys fees, arising out of or in connection with any use or possession by the User of this TND product. These terms and conditions constitute the entire agreement between Rand McNally (and its licensors and suppliers) and the User pertaining to the subject matter hereof, and supersedes in their entirety any and all written or oral agreements previously existing between us with respect to such subject matter. The above terms and conditions shall be governed by the laws of the Illinois, without giving effect to (i) its conict of laws provisions, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded. The User agrees to submit to the jurisdiction of Illinois for any and all disputes, claims and actions arising from or in connection with the Data provided to the User hereunder. User shall not export the TND product in violation of any U.S. or foreign laws. Rand McNallys licensors shall be third party beneciaries of Rand McNallys rights under this license, but are not parties hereto and have no obligations hereunder. By using this product you agree to be bound both by the foregoing and to the terms of use found at www.randmcnally.com/truckgps. Restricted Rights Legend. For governmental agencies: Use, reproduction or disclosure is subject to restrictions set forth in subparagraph (c) (1) (iii) of the Right in Technical Data and Computer Software clause at DFARS 52.227-7013, as amended. Copyright 2010 Rand McNally. All rights reserved. Portions 2008 NAVTEQ. All rights reserved. This data includes information taken with permission from Canadian authorities, including Her Majesty the Queen in Right of Canada, Queens Printer for Ontario. Portions 2010 InfoGation. All rights reserved. Portions 2010 The Truckers Friend. All rights reserved. Patent pending. Please retain your original sales receipt for warranty service. 19 Find More Information Trouver davantage dinformations Encuentre ms informacin