IMMO Bluetooth headphone SPECIFICATIONS Bluetooth version:
V5.3 Bluetooth range 10m Battery:
300mAh Li polymer battery Charging time:
About 3 hours Playing time:
15 hours Stand-by time:
up to 100 hours LED indicator status:
Blue LED for power and BT pairing indicator;
Red LED for charging indicator Diameter of driver unit:
40mm Frequency range:
20Hz~20kHz Frequency band:
2402 MHz- 2480 MHz Sensitivity at 1KHz:
96cB + 3dB Impedance:
32+/-15% O Distortion:
<1% at 1KHz Rated power input 10mW Net Weight:
ACCESSORIES Approx. 172g Type-C charging cable 3.5mm audio cable e Instruction Manual Model:H205 CFE ROHS &&
i ELEMENTS D'EMBALLAGE ASEPARER ET A DEPOSER DANS LE BAC DE TRI
@ Voice Assistant Increase the volume Go to next song On/Off CG Play
(3] Multifunction button oO Pause Call/Answer/Hang Up Decrease the volume
-Q Go to previous song Volume Up/
Volume Down/
4) Track Back =
6 Micro Type-C charging port
(6) 3.5mm audio jack Important Safety Information Listen Responsibly To avoid hearing damage, make sure that the volume on your music player is turned down before connecting your headphones. After placing headphones in/on your ears, gradually turn up the volume until you reach a comfortable listening level. Noise levels are measured in decibels (dB), exposure to any noise at or above 85 dB can cause gradual hearing loss. Monitor your use; hearing loss is a function of loudness versus time. The louder it is, the less time you can be exposed to it. The softer it is, the more time you can listen to it Use Responsibly Do not use headphones when it's unsafe to do sowhile operating a vehicle, crossing streets, or during any activity or in an environment where your full attention to your surroundings is required It's dangerous to drive while wearing headphones, and in many places, illegal because it decreases your chances of hearing life-saving sounds outside of your vehicle, such as another car's horn and emergency vehicle sirens. Please avoid wearing your headphones while driving CHARGING THE HEADPHONES Use the Micro USB cable and connect headphones to your computer or adaptor device made for USB charging. When the Red light is on, the headphones are charging. When the Red light is off,the headphones are full charged. Full charging time is around 2-3 hours. PAIRING Make sure your phone, computer or music device is turned on and within 1 meter of each other.
(2) Press and hold the Multifunction button on the headphones for 3 seconds until the indicator light flashes Blue and Red alternatively(pairing mode) Activate Bluetooth on your phone or other device and search for bluetooth devices and select H205
(4) Once successfully paired, the LED light will flash blue for 3 second, then turn off. Basic Functions Play Short press the (MFB)once to play Pause Short press the (MFB)once to pause Volume UP Press the Volume Up + button in steps to increase volume Press the Volume Down - button in steps to decrease volume Long press the Volume Down - button for playing the previous track Volume Down Previous Track Next Track Long press the Volume Up + button for playing the next track Turn On Voice Short Press the Dedicated Voice Assistant Assistant /Siti Button CALLS
@ To answer an incoming call, press the Multifunction Play/Pause
(button 3) Olo end call, press the same button again To decrease or increase the volume during the call, DUsh UP or down button 3 POWER ON Press and hold the Multifunction button for 3 seconds to turn the headphones on. The LED- indicator will flash BLUE when headphones are on. POWER OFF Press and hold the Multifunction button for 3 seconds to turn the headphones off. The LED indicator will stop flashing when off. Using headphones in Passive Mode (Wired) You can use the headphones as a wired headphone to save battery. Simply connect one end of the 3.5mm cable to the bottom of the ear cushion and the other end to your phone or device. Note: Inserting an audio cable disables wireless functionality. Music Player FCC warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The de vice can be used in portable exposure condition without restriction.