Robert Bosch GmbH 72757 Reutlingen Germany www.bosch-ebike.com 0 275 008 3SG (2nd draft) T / 13 SmartphoneGrip BSP3200 en Original operating instructions zh 2 |
0 275 008 3SG | (25.01.2022) Bosch eBike Systems
(1)(2)(3)(1)(2)(5)(6)(7)(8)(10)(9)(4)| 3 Bosch eBike Systems 0 275 008 3SG | (25.01.2022) 1221AB(6)(12)(5)(11)(5)(5)(4)(16) 4 |
0 275 008 3SG | (25.01.2022) Bosch eBike Systems 12C(15)(1)12D(13)(14) English 1 u Caution! When using the SmartphoneGrip with Bluetooth and/or Wi-Fi, interference can occur with other devices and equipment, aircraft and medical devices (e.g. pacemakers, hearing aids). Likewise, injury to people and animals in the immediate vicinity cannot be excluded entirely. Do not use the SmartphoneGrip with Bluetooth in the vicinity of medical devices, petrol sta-
tions, chemical plants, areas with a potentially explosive atmosphere or on blast sites. Do not use the Smart-
phoneGrip with Bluetooth in aeroplanes. Avoid opera-
tion near your body for extended periods. Safety Instructions Read all the safety information and in-
structions. Failure to observe the safety in-
formation and follow instructions may result in electric shock, fire and/or serious injury. Save all safety warnings and instructions for future ref-
erence. u Read and observe the safety warnings and directions contained in all the eBike system operating instruc-
tions and in the operating instructions of your eBike. u Do not allow your attention to be diverted from sur-
rounding traffic when using Bosch eBike components and always ride with both hands on the handlebars. Al-
ways observe the applicable legal provisions in your country for the permitted use of your bicycle in road traffic. In particular, note that it is prohibited to pick up or hold your smartphone in your hand in road traffic. u Set the display brightness so that you can adequately see important information such as speed and warning symbols. Incorrectly set display brightness may lead to dangerous situations. u The contact surfaces of the display holder may be-
come very hot (>60C). Allow the contact surfaces to adjust to the ambient temperature before you touch them. This is particularly important when using a Smart-
phoneGrip. u Consult a doctor before using fitness app programs. Fitness apps may cause people to overexert themselves physically. u Always observe local restrictions for using electronic devices. u Avoid operation near your body for extended periods. u Do not stand your bicycle upside down on its saddle and handlebars if the SmartphoneGrip or its holder protrude from the handlebars. This may irreparably damage the SmartphoneGrip or the holder. u Do not use the SmartphoneGrip as a handle. Lifting the eBike up by the SmartphoneGrip can cause irreparable damage to the SmartphoneGrip. u Do not open the SmartphoneGrip. Opening the Smart-
phoneGrip may damage it beyond repair and void any warranty claims. Bosch eBike Systems 0 275 008 3SG | (25.01.2022) Remarques ISDE (Canada) Cet appareil contient un/des metteur(s)/rcepteur(s) exempt(s) de licence conforme(s) aux CNR dInnovation, Sciences et Dveloppement conomique Canada appli-
cables aux quipements exempts de licence. Lutilisation est autorise sous rserve des deux conditions suivantes :
lappareil ne doit pas produire de brouillage, et 1. 2. lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compro-
mettre le fonctionnement. Cet quipement respecte les limites dexposition aux rayon-
nements dfinies par le Canada pour un environnement non contrl. Cet quipement doit tre install et utilis en main-
tenant une distance minimale de 20cm entre la source de rayonnement et votre corps. Cet metteur ne doit pas tre plac proximit dune autre antenne ou dun autre met-
teur ou tre utilis en combinaison avec nimporte quelle autre antenne ou metteur. English 2 NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device must not cause harmful interference, and this device must accept any interference received, in-
2. cluding interference that may cause undesired opera-
tion. NOTICE: Changes or modifications made to this equipment not expressly approved by the Robert Bosch GmbH may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful in-
terference to radio communications. However, there is no guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow-
ing measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and re-
ceiver. for help. Connect the equipment into an outlet on a circuit differ-
ent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician Radiofrequency radiation exposure Information: The ra-
diated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. ISED Notice (Canada) This device contains licence-exempt transmitter(s)/re-
ceiver(s) that comply with Innovation, Science and Eco-
nomic Development Canadas licence-exempt RSS(s). Oper-
ation is subject to the following two conditions:
this device may not cause interference, and 1. this device must accept any interference, including in-
2. terference that may cause undesired operation of the device. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equip-
ment should be installed and operated with minimum dis-
tance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunc-
tion with any other antenna or transmitter. 0 275 008 3SG | (25.01.2022) Bosch eBike Systems Technical Data SmartphoneGrip Product code USB charging output power Wireless charging output power W W Maximum RF output power Frequency range Operating temperature Storage temperature Protection rating Weight, approx. KHz C C g English 3 BSP3200 5W (1A at 5Vdc) max 7.5W
(1.5A at 5Vdc) Efficiency > 67%
40.36dBuA/m at 3m distance 110205 5 to 40 10 to 40 IP54 75 Product Description and Specifications Intended Use The Bosch SmartphoneGrip is designed to hold and charge a smartphone on the handlebars of a Bosch eBike system. In addition to the functions shown here, changes to software relating to troubleshooting and functional modifications may be introduced at any time. The manufacturer accepts no liability for damage to mobile devices caused by using this product. The manufacturer ac-
cepts no liability for defects related to damage or loss due to factors outside of the manufacturer's control, or for products that were modified or damaged due to improper or incorrect use. Product Features The numbering of the components shown refers to the illus-
trations on the graphics pages at the beginning of the manual. All illustrations of bike parts except for the drive unit, Smart-
phoneGrip (including operating unit), speed sensor and the corresponding holders are a schematic representation and may differ on your eBike.
(1) Front retraining bracket, movable
(2) Rear retaining bracket, fixed
(3) USB port with USB cap
(4) Release mechanism
(5) SmartphoneGrip mount
(6) Snap-in hook
(7) Socket contacts
(8) SmartphoneGrip contacts
(9) Status LED
(10) Inductive charging coil
(11) Display mount fastening screw
(12) Removal blocker
(13) Keypad lock
(14) Hex key
(15) Smartphone
(16) Adapter tray Bosch eBike Systems 0 275 008 3SG | (25.01.2022) English 4 Assembly SmartphoneGrip Assembly (seefigureA) Press and hold the release mechanism(4) to position the SmartphoneGrip. Place the upper edge of the Smart-
phoneGrip next to the snap-in hook(6) of the display holder(5). Pull the SmartphoneGrip towards you and push the SmartphoneGrip onto the display holder. Let go of the release mechanism(4). Press the release mechanism(4) while pulling it towards you to remove the SmartphoneGrip. Remove the Smart-
phoneGrip and let go of the release mechanism(4). Inserting the Removal Blocker (seefigureB) Insert the removal blocker(12) into the adapter tray(16) from below until you hear the removal blocker(12) click into place. From this point onwards, you can no longer remove the SmartphoneGrip from the display mount(5) without remov-
ing the display mount(5) from the adapter tray(16) by loosening the two fastening screws(11). Note: The removal blocker(12) is not an anti-theft device. Smartphone Assembly (seefigureC) The SmartphoneGrip can hold smartphones in the following sizes:
The specified dimensions include any phone cases. Smart-
phones with folio cases must not be used. The total weight must not exceed 276g. Pull the front retaining bracket(1) forwards. Insert your smartphone(15) with the long side of the phone positioned against the fixed retaining bracket(2). Release the front retaining bracket and place your smartphone(15) in the centre of the SmartphoneGrip. u Be careful not to pinch your fingers between the movable retaining bracket and the SmartphoneGrip when inserting your smartphone. Once you have inserted your smartphone, check that the smartphone cannot come into contact with any hard parts on the bike even in case of vibrations, as this could cause last-
ing damage to the smartphone. Keypad Lock Assembly (seefigureD) To remove the keypad lock(13), unscrew the securing screw with a hex key (1.5mm)(14) and remove the keypad lock(13). To insert the keypad lock(13), slide the keypad lock(13) into the provided opening and screw it into place with a hex key (1.5mm)(14). Note: The keypad lock is not an anti-theft device. The keypad lock prevents the SmartphoneGrip from being quickly removed from the holder. The keypad lock does not affect the smartphone in any way Note: Never leave your smartphone unattended in the SmartphoneGrip. Operation Starting Operation Place your smartphone in the SmartphoneGrip. Start theeBike Flow app to have riding data displayed. Depending on the smartphone's operating sys-
tem, theeBike Flow app can be downloaded free of charge from the Apple App Store and the Google Play store. Use your smartphone to scan the code in order to download theeBike Flow app. Charging your Smartphone While the smartphone is in the SmartphoneGrip, it can be charged at the same time as displaying riding data. If your smartphone has an inductive charging function, you can charge the smartphone without needing a cable. Inductive Charging The charging process starts automatically when you place a smartphone with an inductive charging function in the SmartphoneGrip. The status LED(9) lights up yellow. When the smartphone is fully charged, the status LED(9) will light up green permanently. The charging voltage is switched off when you remove the smartphone from the holder. Charging via USB If your smartphone does not have an inductive charging function, you can charge your smartphone via the USB port(3). To do so, open the USB cap and connect a separate USB cable (not included in the scope of delivery) to the Mi-
cro-AB USB port. Pay attention to the type of plug required for your smart-
phone when purchasing the USB cable. 0 275 008 3SG | (25.01.2022) Bosch eBike Systems 6788 mm6,813 mm123175 mm Status Indicators The status LED(9) indicates the following statuses with dif-
ferent colours and lighting patterns:
Please return Bosch eBike components that are no longer usable free of charge to an authorised bicycle dealer. Subject to change without notice. English 5 Status Behaviour Charging via USB LED lights up blue. Inductive charging starts LED flashes yellow 3 times. Inductive charging Fully charged LED lights up yellow. LED lights up green. Inductive charging alarm LED flashes red. The following alarm states are detected and will lead to the inductive charging process being interrupted:
Detection of foreign objects, e.g. coins, keys or other metallic objects Temperature alarm The charging process will switch off at temperatures above 78C. The charging process is continued once the temperature drops below 56C. Overvoltage alarm at voltages above 6V Undervoltage alarm at voltages below 4.2V Maintenance and servicing Maintenance and cleaning Use a soft cloth dampened only with water for cleaning. Do not use cleaning products of any kind. u Have all repairs performed only by an authorised bike dealer. Do not clean any of the components with pressurised water. Transport u If you transport your eBike attached to the outside of your car, e.g. on a bike rack, remove the Smart-
phoneGrip and the eBike battery to avoid damaging them. After-sales service and advice on using products If you have any questions about the eBike system and its components, contact an authorised bicycle dealer. For contact details of authorised bike dealerships, please visit www.bosch-ebike.com. Disposal The drive unit, on-board computer incl. operat-
ing unit, battery, speed sensor, accessories and packaging should be disposed of in an en-
vironmentally correct manner. Check that your personal data has been deleted from the device. Do not dispose of eBikes and their components with house-
hold waste. Bosch eBike Systems 0 275 008 3SG | (25.01.2022) English 6 0 275 008 3SG | (25.01.2022) Bosch eBike Systems u eBike eBike u Bosch eBike u u >60C SmartphoneGrip u App App u u u SmartphoneGrip SmartphoneGrip u SmartphoneGrip SmartphoneGrip eBike SmartphoneGrip u SmartphoneGrip SmartphoneGrip u SmartphoneGrip /
SmartphoneGrip SmartphoneGrip Bosch SmartphoneGrip Bosch eBike 1 SmartphoneGrip eBike
(1) /
(2) /
(3) USB USB
(4)
(5) SmartphoneGrip
(6)
(7)
(8) SmartphoneGrip
(9) LED
(10)
(11)
(12)
(13)
(14)
(15)
(16) SmartphoneGrip USB BSP3200 5 W1 A@5 V W W 7.5 W1.5 A@5 V
> 67 %
C C g 5 ... 40 10 ... 40 IP54 75 SmartphoneGripA SmartphoneGrip(4) SmartphoneGrip
(5) (6) SmartphoneGrip SmartphoneGrip
(4) SmartphoneGrip (4) SmarthoneGrip
(4) Bosch eBike Systems 0 275 008 3SG | (20.12.2021) 2 B
(12) (16)
(12)
(11)
(5) (16) SmartphoneGrip (5)
(12) C SmartphoneGrip 276g
(1) (15)
(2)
(15) SmartphoneGrip u SmartphoneGrip D
(13) 1.5mm(14)
(13)
(13) (13) 1.5mm
(14) SmartphoneGrip SmartphoneGrip SmartphoneGrip eBike Flow Apple App Store Google Play Store eBike Flow eBike Flow SmartphoneGrip SmartphoneGrip LED
(9) LED (9) USB USB (3) USB USB Micro-AB USB USB LED (9) USB LED LED 3 LED LED LED
>78 C 56C 6V 4.2V u u eBike SmartphoneGrip eBike 0 275 008 3SG | (20.12.2021) Bosch eBike Systems 6788 mm6,813 mm123175 mm 3 eBike www.bosch-ebike.com eBike Bosch eBike Bosch eBike Systems 0 275 008 3SG | (20.12.2021)