Learning SMART LOCK Installation Guide To Custermer 1 4 7 RBT3.0 2 5 8 0 3 6 9 Instruction Manual Before use Please read this manual thoroughly in order to use this product properly. Please keep this in case that a problem occurs.
* Please do not reprint or copy the contents of this manual without permission. The appearance and specications shown are subject to change without prior notice for improvement. The compensation for errors etc. described in this manual will not be made. We are constantly improving the quality of our products. Depending on the time you purchased, there are some differences among the same products. Please understand. The contents of this manual may be changed without notice in the future. Company names and product names described in this manual are trademarks or registered trademarks of each company. 3 3 4 6 8 9 1 0 1 0 1 1 1 1 Table of contents Before use Items included Notice before use About this product Name of parts Initial set upTablet Pincode registration Basic features Pin code IC card Open/Close button Thumb turn Use from kit appTablet LockUnlock IC card registration Change your pincode Auto lock Pairing 1 8 1 9 2 0 2 1 1 2 2 3 2 4 2 5 2 7 2 8 Advanced features Register master card Register user card Deletion of user card Deletion of master card Silent mode Other features Notication of low battery Emergency power supply Reset the device by using emergency power supply terminal Alart Sound setting Specication Compatible lock cases 3 0 3 0 3 0 3 1 3 2 2 9 2 9 2 Before Use Please read this manual thoroughly in order to use this product properly. Items included Please check the below items are included in this package. The below gures may look slightly different from they actually are. Main unit Key sylinder cap Master cardIC card Internal External 3 Before Use Please read this manual thoroughly in order to use this product properly. Notice before use Please keep your physical key in case of emergency. Please use unused Alkalin batteries. Otherwise, it may shorten the battery life, or worse, cause the device failure. It's recommended to replace batteries once a year. It is also recommended to operate the lock a few times a month at least since leaving it unused with batteries loaded may causes liquid leaks of the batteries. Do not give it a strong impact like by dropping it or hitting with a hammer. Please keep your IC card. If you lost it, delete the old one and re-register your new IC. We will not be responsible for any damage caused by or relating to the card you lost. Use your physical key instead in case if you cannot unlock it with your IC. In case you don't have the physical key, please consult with a locksmith. In case you live in an apartment, please consult with the owner or a manager of its property. Even if you use the autolock features, please make sure it's locked. We will not be responsible for any damage caused by leaving the door unlocked. Be careful not to locked out when using this feature. Do not tamper with Open/Close button or the sensor part. Do not clean this with organic solvent such as alcohol. Do not directly put water on it. These actions causes serious accident such as electric shock and re. Please follow building rules if you live in a rental house. 4 Before Use Please read this manual thoroughly in order to use this product properly. Notice before use Since prepaid transportation cards may be replaced when you update it, please register another card for your back up. Also, do not use Korean prepaid transportation card nor Smartphones which may share its ID with another card/
device. Do not bend, make holes on, nor expose high temperature the device. You can use AC power supply with batteries loaded. But this usage may cause liquid leak of batteries, which will not be covered by our warranty policy. Do not dissemble nor modify the device. Do not leave the device under a high temperature nor high humidity condition. Do not use this under such a condition having much condensation. Do not use the device in such a place with high humidity, much dust, or fume. RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Part 15 Statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. 5 Before Use Please read this manual thoroughly in order to use this product properly. Notice before use Modication warning Caution!
Any changes or modications (including the antenna) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. 6 Before Use Please read this manual thoroughly in order to use this product properly. About this product This product is an electronic device that can control many types of locks via various way such as blue tooth, IC card, and personal pincode. 1. How to use IC cardMaster card (up to 5), User card (up to 300) Your personal pincode Bluetooth Application is required Physical key 2. How to use when you go out Pushandin this order to lock the door. If you use autolock feature, the door will be locked 1 sec later it's closed Step1 Step2 When you come home Push Open / Close button.If you use autolock feature, the door will be locked 1 sec later it's closed Push Open/Close button 7 Before Use Please read this manual thoroughly in order to use this product properly. About this product 3. Features Bluetooth Control the device remotely via kit application IC card IC cards conforms to international standards such as ISO14443A, ISO15693, ISO18092 can be registered as a master card. Some IC card cannot be registered depending on their quality. Autolock By using this feature, the door will be closed automatically 1 sec after you close the door. Silent mode You can mute the sound when you put IC card, etc. Emergency alart cannot be muted. Emergency alart In case of emergency, this gives you an alart with the sound more than 100B. Emergency power supply terminal You can supply power to the device in case the batteries out. Also, you can reset the device by using the same terminal in case it's freezed. 8 Name of parts IC reader unit IC reader region the region to hold IC card up over Start-up key Key to start the device Pressing any key can start the device Emergency power supply terminal The to supply power through when the battery is out. Key Cylinder cover This cover is for protecting Emergency power supply terminal. Slide it down to get off. Dip switch terminal 1 2 3 4 5 6 7 8 Switch number ON Do not use Alart sound OFF Do not use ON Silent mode2 Be careful not to lock accidentally. You may be locked out. Silent mode cannot mute the alart sound. Do not use OFF Thumb turn/battery unit Battery unit cover This cover is for protecting battery and operation buttons. Slide it up to get off. mini USB port data communication Thumb turn Manual operation Open/Close button Lock/unlock from inside Push C button Push to register IC card R button Push to register pincode AAA alkaline battery Insert 4 AAA alkaline battery 9 Initial set upTablet Pincode registration You can unlock the door with your pincode even if you don't have smartphone nor IC card with you. This is also needed during the authentication process performed on the tablet. Prerequisitit uses Bluetooth. The distance between the tablet and the lock should be within 10m. Tap smart lock Tap personal pincode Input your pincode of 4-12 digits OFF pincode should be 4 to 12 digits Conrm your pincode Done 10 Basic feature Pin code IC card Please follow the below procedure to use your pincode The button you press rstly The button you press lastly Hold IC card after start-up key to unlock the door. Start-up key Start-up key can be any button on the key pad. IC reader Sensitivity differs on its quality and kind. Please use sensitive one to register. Pincode Step registered number of 4 to 12 digit Step Step Press start-up key Hold IC card up over the reader unit 11 Basic feature If you don't use autolock, the door will be locked when you pressandin this order. Open/Close button Thumb turn Open/Close button Thumb turn Step Push Open/Close button Step Like ordinary thumb turns, you can lock and unlock by turing it. 12 Use from kit appTablet Lock Unlock PrerequisitThe lock should be paired with the tablet. Please refer to p22.Pairing If you don't use autolock, the door will be locked when you pressandin this order. Tap the button of Smart lock card on the tablet unlocked The screen shot shown may be different from actual one depending on the version of the lock you use. lock Your tap toggles the status of the lock unlock 13 Use from kit appTablet IC card registration Prerequisitit uses Bluetooth. The distance between the tablet and the lock should be within 10m. Registration of all IC card will be canceled if you perform set-up procedure from kit app. Tap smart lock Tap unregister IC card Inpurt your pincode OFF Tap delete all done 14 Use from kit appTablet Change your pincode Prerequisitit uses Bluetooth. The distance between the tablet and the lock should be within 10m. tap smart lock Tap change pincode Input the current pincode OFF 412 input new pincode conrm your pincode done 412 412 Pincode digit is from 4 to 12 15 Use from kit appTablet Auto lock Prerequisitit uses Bluetooth. The distance between the tablet and the lock should be within 10m. The device lock itself spontaneously if you left the door closed after unlocking it. This happens even if you don't use Auto lock feature. Tap smart lock Tap auto lock Please check the Autolock is
"on"
OFF ON 16 Use from kit appTablet Pairing Prerequisitit uses Bluetooth. The distance between the tablet and the lock should be within 10m. PrerequisitRegister your personal pincode to the lock.Please refer to p15.Pincode registration Tap +
Select Smart lock Input the name of this device Select the serial number of your device Input your pincode Done 17 Advanced features Register master card Register master card Prepare master cardup to 5 cards can be registered Push C R Procedure Prepare IC card Step1 Push C button twice Uncover the battery unit and push C button once then you will hear "pit pit pit lot lot"
Step Step Hold your IC card Hold your IC card up over IC reader unit, you will hear "pit pot" and the card is registered as a master card. To register another master card, hold it within 5 sec Procedure will be completed once you push button or leave it for 5 sec. In the latter case, you will hear "pit pit"
Hold your master card Uncover the battery unit Push C button
"pit"
Push C button again
"pit"
"pit lot lot lot"
Hold IC card within 5 sec
"pit pot"
To register another card, hold it within 5 sec
"pit pot"
Push C button
"pii pho pii"
Done 18 Advanced features Register user card Register user card Contrary to master card managing all the registered info, up to 300 user cards can be registered to one device. This can be used to allow your colleague or family members to open the door. Some IC card cannot be register due to its low quality. Push and hold your card you want to register. If you hear
"pii pii pii", your card is compatible. Otherwise it's not. Allocate 3 digits block number to your card Step4 Hold your IC card Hold your IC card up over the reader unit and you will hear "pit pot"
Step5 Step6 Input Input # and it makes sound of "pii pho pii". Repeat step 3-5 to register another card. Push C button once Procedure will be completed once you push button or leave it for 5 sec Procedure Step 1 Push C button once Uncover the battery unit and push C button once then you will hear "pit"
Step2 Step3 Hold your master card Hold your master card up over IC reader unit, you will hear "pii pho pii".If you hear
"pii pii", it's not your master card or the battey is low. Input digits block number +
Input digits block number +, you will hear "pit pot"
You can choose your own block number. You cannot register multiple cards to one block number. Please keep the number. It's needed to delete the card. Push R C Uncover the battery unit and push C button once
"pit"
Hold master card Hold your master card within 5 sec
"pii pho pii"
Input digits block number +
"pit pot"
Hold IC card Hold your IC card
"pit pot"
Input
"pii pho pii"
Procedure will be completed once you push button to register another card 19 Advanced features Deletion of user card Delete an individual IC card Uncover the battery unit and push C button once You can delete a card individually by its block number. If the block number is unknown, you cannot delete it individually. You cannot delete multiple cards at once. Procedure Push C R Step Push button once Uncover the battery unit and push C button once then you will hear "pit"
Step Push button Procedure will be completed once you push button or leave it for 5 sec Step Step Step Step Hold your master card Hold your master card up over IC reader unit, you will hear "pii pho pii" and the card is unregistered. Push C button once Uncover the battery unit and push C button once then you will hear "pitpot"
Input 3 digits block number Input block number which occupied by the card you want to unregister and, then you will hear "pit pit"
Input 3 digits block number Input block number and
, then the card is unregistered with the sound of "pii pho pii"
Hold master card
"pit"
Hold your master card up over IC reader unit within 5 sec
"pii pho pii"
Push C button once
"pit pot"
Input 3 digits block number Input
"pit pit"
Input 3 digits block number again Input
"pii pho pii"
Push C button once Deletion completed 20 Advanced features Deletion of user card Delete all user cards Procedure Step Push C button Uncover the battery unit and push C button once then you will hear "pit"
Step Push button once Push R button once and you will hear "pit"
Step Push C button Push C button once and you will hear "pit"
Step Hold your master card Hold your master card up over IC reader unit with in 5 sec, you will hear "pii pho pii" and the card is unregistered. Easy to set up via kit app!
Registration of all IC card will be canceled if you perform set-up procedure from kit app. Push C R Hold your master card Uncover the battery unit and push C button once
"pit"
Push button once
"pit"
Push C button once
"pit"
Within 5 sec Hold your master card
"pit"
21 Advanced features Deletion of master card Deletion of master card Easy to set up via kit app!
Registration of all IC card will be canceled if you perform set-up procedure from kit app. Prepare your master card All the registered mastercards will be deleted if you delete one of them. User card will not be deleted. Your personal pincode will be deleted if you delete your master card. Procedure Step Hold button for 5-10 sec Uncover the battery unit and hold button for 5 sec. It makes sound of "pit" when you push C button and
"pilololot" if you hold it for 5 sec then release the button. Step Hold your master card Hold your master card up over IC reader unit with in 5 sec, you will hear "pii pho pii" and the card is unregis-
tered. Push C R Hold the master card Hold C button for 5-10 sec
"pit"
"pit lot lot lot"
Hold your master card with in 5 sec
"pii pho pii"
Deletion completed 22 Advanced features Silent mode Emergency alart cannot be muted. You can mute the sound by using this feature. In the default setting, the device gives sounds. Step Remove a battery Remove one battery by uncovering the battery cover. Step Step Step Change the 3rd dip switch to Change the 3rd dip swithch to with a screw driver as shown below. Push Open/Close twice Discharge stanby current and reset the device Insert a battery Insert a battery back to the main unit and the procedure is completed. Change therd switch to dip switch 23 Other features Notication of low battery No need to set up for this. When batteries are low, LED of Open/Close button blinks and the melody of twinkle twinkle little star gives you an alart. You can use the lock approx. 300times after this alart starts. But it's recommended to change all the batteries at once as soon as possible. When you change batteries, please push Open/Close button several times to discharge the standby current. Emergency power supply Emergency power supply offers you a way to supply power even when the batteries are out. Procedure Prepare 0069Alkaline battery Step Step Hold the battery to the terminal If you hold the battery to the emergency power supply terminal, you will hear the start up sound the direction of terminal of the battery against the emergency terminal doesn't matter Push Pushwhile holding the battery against the terminal, you will hear
"pit" sound. Step Hold the IC card or input pincode. Hold your registered IC card or input your personal pincode while holding the battery against the terminal, the lock will be unlocked. If succeeded, please replace sll the batteries with new ones at once. 006P9V Alkaline battery IC reader unit Emergency power Emergency power supply supply Hold the battery contacting the emergency terminal Start-up sound Push
"pit"
Hold IC cards Input personal pincode in 5sec Hold IC cards or input personal pincode
"pit"
Unlocked 24 Other features Reset the device by using emergency power supply terminal In case the device is freezed by static electoricity or other reasons, the device can be reset by supplying power from the emergency terminal. Step1 Open the door Keep it open Push Open/Close button and open the door you can supply power regardless of the direction of the battery
+- terminal. supply terminal supply terminal Emergency power Emergency power hold the battery like hold the battery like above gure shows above gure shows Start up sound Sound setting You can chose the sound volume from Big and Small. The default is Small. The sound volume of emergency alart cannot be changed. Step Step Open the door keep it open Push Open/Close to open the door Hold Open/Close for 5 sec Hold Open/Close for 5 sec and this gives a sound like "pit pit pit pit pit lot"
Step Push 7 Push 7 and the sound volume is set Small Alart For countermeasure against invasion, this device gives off an alart sound more than. This can be occured in case the magnet accidentaly come off, someone try opening the door before unlocking or opening the door just before it closes. Please stop alart with the door open and the alart is running. hold it for 3 sec Open the door Step1 Step Step Open the door keep it open Push If you push #, it sounds like "pit"
to conrm. Hold your registered IC card on it The alart stops if you hold your registered IC card on the device. Hold Push
"pit"
In 5 sec hold the registered IC card Alart stops Close the door Push Open/Close button
"pit pit pit"
Unlocked Hold Open/Close button for 5 sec
"pit pit pit pit pit lot"
Same procedure switched the sound volume from Small to Big. Be careful not to leave the door unlocked in case you are not using Autolock function. Push 7 and this procedure is completed. 25 Specication Model Main unit IC reader unit Power supply ECO mode RBT3.0 6514053mm 5510529mm AAA Alkaline batteriesuse 10 times a day=aprox. 1 year / 006P batteriesfor emergency power supply ECO mode ONOFFONconstant power supplyOFFsleep after certain period Compatible IC standard ISO14443AISO15693I-CORDFeliCa Limit of operation record 3,000 Alart sound more than 100dB Operation temperature 1045 All the data is collected under the conditions determined by RobotHome. The content can be changed without prior notice. Bluetooth is a trademark of Bluetooth SGI Inc. in USA. Other company names and product service names are trademarks of each company. 26 Specication Compatible lock cases MIWA LALAFBH DADAF POSTELSPLETEFG PP POM Others, OEM Locks GOAL SHIBUTANI LX series, LG series, LDseries, others CDS seriesLCS series Compatible backset length 38516476mm Compatible door thickness 30 60mm the door with the thickness more than described left can be compatible with special adaptors. All the data is collected under the conditions determined by RobotHome. The content can be changed without prior notice. Bluetooth is a trademark of Bluetooth SGI Inc. in USA. Other company names and product service names are trademarks of each company. 27 Robot Home Co.,Ltd. Learning SMART LOCK For more information, visit robothome.co.jp Company outline Robot Home Co., Ltd.