FCC ID: ANSBP3595 Wireless LAN Module

PRODUCTS HYBRID IC TYPE BP3595 PAGE 1/22

<Specifications (Precautions and Prohibitions)>

Precaution on using ROHM Products 1) Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment, OA equipment, telecommunication equipment, home electronics appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (Special Applications), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHMs Products for Specific Applications. 2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures.

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3) Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHMs Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other electromagnetic waves flammable items

[f]Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering

[h] Use of the Products in places subject to dew condensation 4) The products might receive the radio wave interference from electronic devices such as Wireless LAN devices, Bluetooth devices, digital cordless telephone, microwave oven and so on that radiate electromagnetic wave. 5) The Products are not subject to radiation-proof design. 6) Please verify and confirm characteristics of the final or mounted products in using the Products. DESIGN CHECK APPROVAL DATE: 21/Oct./2015 SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211104002 REV.B PRODUCTS HYBRID IC TYPE BP3595 PAGE 2/22

<Specifications (Precautions and Prohibitions)>

7) This product is a specification to radiate the radio wave. It is necessary to acquire the attestation of decided Radio Law of each region used to use the equipment that radiates the radio wave. Please inquire about the attestation of Radio Law that this product acquires. 8) Confirm that operation temperature is within the specified range described in the product specification. 9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precautions Regarding Application Examples and External Circuits 1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2) You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise you own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM Temperature: 540, Humidity 40%60%

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic 2) Even under ROHM recommended storage condition, connector mating of products over 1 year old may be degraded. 3) Store / transport cartons in the correct direction, which is indicated on a carton as a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. QR code printed on ROHM product label is for ROHMs internal use only, and please do not use at customer site. Precaution for product label Precaution for disposition When disposing Products please dispose them properly using an authorized industry waste company. REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 3/22

<Specifications (Precautions and Prohibitions)>

Precaution Regarding Intellectual Property Rights 1) All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2) ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software) 3No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Matters ROHM. 1) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of 2) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3) In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4) The proper names of companies or products described in this document are trademarks of registered trademarks of ROHM, its affiliated companies or third parties. REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 4/22 1. STRUCTURE P.C.BOARD ASSEMBLY 2. PRODUCTS HYBRID INTEGRATED CIRCUIT 3. TYPE BP3595 4. APPLICATION COMMUNICATION APPLIANCE 5. FUNCTION WIRELESS LAN COMMUNICATION 6. ABSOLUTE MAXIMUM RATINGS No. 1 2 3 PARAMETER Power supply voltage Operating temperature range Storage temperature range SYMBOL VCC Topr Tstg LIMITS

-0.3 +3.6

-40 +85

-40 +85 UNIT V REMARKS DC No No condensation condensation Note) These are the values that must not be exceeded at any time under any application or any test conditions. Please make design keeping enough margins accordingly. 7. RECOMMENDED OPERATING CONDITIONS PARAMETER Power supply voltage No. 1 2 Operating temperature range SYMBOL VCC Ta MIN. 3.1

-40 SPEC TYP. MAX. 3.5 3.3 25 85 UNIT V REMARKS

-

-

REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 5/22 8. MAIN CHARACTERISTICS No. 1 2 PARAMETER Frequency width Frequency tolerance 3 RF output power (*1) 4 Supported data rates 5 6 7 8 Receiving sensitivity (*1) Security function Host Interface Power supply voltage CHARACTERISTICS 2,400MHz 2,483.5 MHzch1ch13 Within 25ppm IEEE802.11b 15dBm2dB IEEE802.11g 13dBm2dB IEEE802.11n 12dBm2dB IEEE802.11b 1 11Mbps IEEE802.11g 6 54Mbps IEEE802.11n 6.5 72.2Mbps IEEE802.11b -94dBm @1Mbps, -89dBm @11Mbps IEEE802.11g -92dBm @6Mbps, -73dBm @54Mbps IEEE802.11n -90dBm @6.5Mbps, -68dBm @72.2Mbps 64bit/128bit WEP, TKIP, AES (*2) USB2.0 (High-Speed mode) SDIO Ver.2.00 (High-Speed mode) UART (921600bps) SINGLE 3.3V

(*1) RF output power and Receiving sensitivity are performance value that is at the electricity supplying point for antenna in the below figure.

(*2) 64bit/128bit WEP, TKIP, and AES are everything processed with hardware. 9. BLOCK DIAGRAM A Flash memory (option) is necessary for use the flash boot function. Fig 1. Block diagram REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 6/22 10. ELECTRICAL CHARACTERISTICS CONDITIONSTa=25, VCC=3.3V, GND=0.0V No. PARAMETER CONDITION 1 2 3 4 5 6 Consumption current Center frequency Frequency tolerance Sending Receiving Sleep mode

-

-

11b11Mbps RF output power 11g54Mbps 11nMCS7 Unnecessary out-of-band radiation

-

Transmit spectrum mask DSSS 11Mbps OFDM 54Mbps 11b11Mbps 7 Receiving sensitivity 11g54Mbps 8 Unnecessary radiation for receiving 11nMCS7 Fr<1GHz Fr1GHz MIN. 240 280 160 200

-

2412

-25 13 11 10

-

-

-

-

-

-

-

-

-

-

UNIT REMARKS SPEC TYP. MAX. 300 360 400 340 240 200 280 240 1

-

-

-

15 2472 25 17 13 12

-

-

-

-

-

-

-89 15 14 2.5

-30

-50

-20

-28

-40

-76 mA mA mA mA mA MHz ppm dBm dBm dBm dBr dBr dBr dBr dBr dBm

-73

-65 dBm

-68

-

-

-64 4 20 dBm nW nW Continuous Continuous (With USB) With USB

-

-

-

-

At electricity supplying point for antenna At electricity supplying point for antenna At electricity supplying point for antenna 1st Side-lobe 2nd Side-lobe 11MHz 20MHz 30MHz PER<8%

At electricity supplying point for antenna PER<10%

At electricity supplying point for antenna PER<10%

At electricity supplying point for antenna

-

-

uW/MHz

-

REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 7/22 11. TERMINAL FUNCTIONS Back side 30 1 16 15 NAME V28_STBY GPIO2 GPIO1 GPIO6 GPIO0 No. TERMINAL 1 BOOT_SEL0 2 GPIO8/32k 3 4 5 6 7 8 V12_STBY 9 UART_TXD 10 UART_RXD FLASH_TXD 11 FLASH_CLK 12 13 FLASH_CSB 14 FLASH_RXD 15 16 17 18 19 20 21 22 23 VCC 24 VCC 25 SDCLK 26 SDDATA0 27 SDDATA1 28 HOST_SEL 29 FLASH_SEL 30 BOOT_SEL1 SDDATA2 SDDATA3 SDCMD USB_DM USB_DP PRST GND GND I/O I(*) I/O I/O I/O I I/O I/O I O I I/O O O I I

-

-

I/O I/O I/O

-

-

I I/O I/O I(*) I(*) I(*) AI/O AI/O BP3595 Connector (Receptacle) Type DF40C-30DS-0.4V(51) (Hirose electric Co., Ltd.) User-side Connector (Plug) Type DF40C-30DP-0.4V(51) (Hirose electric Co., Ltd.) Table 1. Module Terminal Functions FUNCTIONS REMARKS Boot mode select General purpose Input/Output 8 General purpose Input/Output 6 General purpose Input/Output 0 V28 LDO Stand-by port General purpose Input/Output 2 General purpose Input/Output 1 V12 LDO Stand-by port UART sending data UART receiving data Flash memory sending data Flash memory clock Flash memory chip select Flash memory receiving data Power on reset Ground USB data minus USB data plus Ground SDIO data 2 SDIO data 3 SDIO command Power supply 3.3V Power supply 3.3V SDIO clock SDIO data 0 SDIO data 1 Host I/F select Flash memory area select Boot mode select

(**)

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

GPIO 8 or 32.768kHz clock input Active Hi (VCC Voltage) Active Hi (VCC Voltage) Terminal for flash boot Terminal for flash boot Terminal for flash boot Terminal for flash boot 0:Reset, 1:Normal Module power supply input Module power supply input 0:USB, 1:SDIO 0:region1, 1:region2

(**) TSZ2211105002 REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) PRODUCTS HYBRID IC TYPE BP3595 PAGE 8/22

(*) FLASH_SEL/HOST_SEL/BOOT_SEL0/BOOT_SEL1 terminal hold the value after reset (Power On Reset). After reset, these terminals are used for another purpose in the module. They have pull down resistance inside. Therefore, please set these terminals OPEN in case of setting for 0 and Pull up 3.3V (power supply voltage) with 3k5k resistor (recommendation is 4.7k resistor) in case of setting for 1. When the host MCU controls these terminal, please do not connect directly with output terminal of host MCU and insert 3k5k resistor (recommendation is 4.7k resistor) between them. When FLASH BOOT function is not used, FLASH_TXD terminal (pin 11) should be connected pull down resistor of 47k. When FLASH BOOT function is used, FLASH_TXD terminal (pin 11) and FLASH_RXD (pin 14) terminal would be connected pull down resistor, if you need. PRST is POWER ON RESET terminal. It is connected 4.7k resistor + 2.2uF capacitor at 3.3V inside the module. In case that need to watch the power supply voltage, please connect such as OPEN DRAIN RESET IC for this terminal. V12_STBY terminal and V28_STBY terminal control LDO which are mounted BP3595. Hi(VCC voltage): active, Lo(GND):stand-by Please open the other unused terminals.

(**) BOOT_SEL terminals select the interface to boot the firmware.. BOOT_SEL[1:0]

00:USB, 01:SDIO, 10:FLASH, 11:UART REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 9/22 12. DIMENSIONS Fig.2 DimensionsUnit: mm 13. MARKING SPECIFICATION 123*

Marking 123*: Production lot number (3 digits + 1 internal serial number) Example123Year 2011 Week 23th Fig.3 Marking specificationBack side REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 10/22 14. PRECAUTIONS FOR MOUNTING Pattern Antenna Pattern Prohibition Area Screw Hole (M2) Shield Case Fig.4 Precautions for Mounting (Unitmm) Connector

(1) Please dont patterning the area under pattern prohibition area so that there is an adverse effect in a wireless characteristic.

(2) Please do not set your substrates and chassis around the chip antenna within 1cm.

(3) Please do not use metals as the material of the chassis.

(4) Please do not mount parts under this module except a specified connector. ABOUT THE FIXATION OF THIS MODULE Please use the M2 screw (made of metal) for fixing BP3595. M2 screw hole is GND potential of this module, please use the metal spacer of 1.5mm height, between your substrate and this module. A torque to tighten M2 screw should be more than 1kgfcm, and do not tighten the screw too much. M2 screw BP3595 Pattern antenna Spacer Nut User side PCB Fig.5 Fixed Module Figure (Side view) REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 11/22 15. PRODUCT LABEL SPEC The label shown in the following figure is put on the shield case. Fig.6 Product Label Spec

*Micro QR code is included in the MAC address information.

(Note)The design of product label might change without previous notice. REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 12/22 16. REFERENCE CIRCUIT 16.1 USB HOST INTERFACE Fig.7 USB Interface Reference Circuit

*About USB_DP and USB_DM Lines Please shorten wiring as much as possible. Please take the differential impedance matching to 9010%. Please set up to 4510% for impedance matching of single end. Please wire USB_DP and USB_DM lines as same lengths.

(Difference of the wire length is less than 0.5mm.) Please do not bend USB lines many times and make the bend angle small. Please do not make threw hole in wiring. Please do not cross the USB lines and another signal lines. Please do not cross the USB lines and power supply lines.

*Please reduce the ripple of power supply (VCC=3.3V) as much as possible. (less than 10mVpp) REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 13/22 16.2 SDIO HOST INTERFACE

*Please reduce the ripple of power supply (VCC=3.3V) as much as possible. (less than 10mVpp) Fig.8 SDIO Interface Reference Circuit

*About the line of SDCLK/SDDATA/SDCMD Over shoot and under shoot of signal lines cause a lot of damage to wireless performance. Please design your product lower noise levels within the SDIO standard timing. For example it can be insert dumping resistors near the host signal source. REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 14/22 16.3 UART INTERFACE

*Please reduce the ripple of power supply (VCC=3.3V) as much as possible. (less than 10mVpp) Fig.9 UART Interface Reference Circuit REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 15/22 16.4 FLASH BOOT (UART INTERFACE MODE) LE25U40CQH-AH (Sanyo Semiconductor) or W25X40CLZPIG (Winbond) Fig.10 Flash Boot (UART INTERFACE )Reference Circuit 16.5 Reset IC

(ROHM) Fig.11 Reset IC Connection Reference Circuit REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 16/22 17. PACKING SPEC 17.1 Packing Method In principle, 25 pieces of modules should be packaged in the packaging tray, and it should be piled up 12 steps to make 300 pieces, and with an empty pack on the top. The number of piling might change according to the quantity of delivery without previous notice. Tray Packing case Fixed by adhesive cellophane tape.

(4 places) Fixed by adhesive cellophane tape.

(3 places) Fig.12 Packing Method 17.2 Label indication The label with following things is stuck at the packing case. Type nameBP3595 Quantity Lot No. Shipment inspection stamp Country of origin Manufacturing company nameTrade mark Logotype of lead free Please refer to the following example of the label indication. TSZ2211105002 F CHINA S.MIZUHARA Fig.13 Label Indication REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) PRODUCTS HYBRID IC TYPE BP3595 PAGE 17/22 18. MANUFACTURING FACTORY ROHM APORO CO., LTD. (FUKUOKA, JAPAN) ROHM ELECTRICS DALIAN CO., LTD. (DALIAN, CHINA) 19. OPERATING PRECAUTIONS 1There is some case that the MAC address does not become sequential number in a same packing. 2About soldering of mounting parts on this product, presence of soldering fillet does not be asked. 3About the products label, defections does not be asked except coming off, lapping, or not to recognize the characters extremely. 4A connector is possible to break by excessive swing or shock because of the structure of the product. Efficient evaluation is necessary to use the module when there is a fear of swinging or shocking. 5The connector of BP3595 does not have a specification assumed to do many times of extraction and insertion. Please be sure that the number of extraction and insertion is within 10 times. 20. PRECAUTIONS AS RESET OPERATION Please do not reset (PRST, COMMAND RESET) when BP3595 is accessing to its internal EEPROM. BP3595 under writing to the EEPROM is reset (*), which may cause unexpected failure such as incorrect checksum. BP3595 under reading from the EEPROM is reset (**), which may cause unstable condition, and you should supply VCC power again.

(*) About write operations of the EEPROM BP3595 writes to the EEPROM in the following cases. Recording various settings used in TCP/IP firmware Recording credential data which is obtained when BP3595 with stand-alone mode acts WPS

(**) About read operations of the EEPPROM BP3595 reads from the EEPROM in the following cases. After reset (100ms) After firmware starting (100ms) When WID_SERIAL_NUMBER command is issued. REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 18/22 21. PRECAUTIONS AS A WIRELESS EQUIPMENT 1 BP3595 acquired Construction design attestation (Article 38-24, Clause1 of Radio Law in Japan) of Particular wireless equipment: Low power data communications system in the 2.4GHz band, which is a Wireless equipment in Article 2-1(19) Therefore, only in Japan, it is possible to use as wireless equipment without applying for wireless office. Construction design attestation No. : 003-120319 Be sure to keep following notes to use the module safely as wireless equipment. 1The label on the module is a certification which shows it has Certification of technical standard conformity. Please do not remove the label or do not put another label on the label. 2Please do not resolve or remodel strictly because there are some cases of receiving penalty based on Radio Law in Japan. 22. PRECAUTIONS AS A WIRELESS EQUIPMENT 2 BP3595 acquired radio law certified in U.S.A (Federal Communications Commission Part15 Subpart C). BP3595 is able to use in U.S.A without application of FCC. FCC ID: ANSBP3595 Please following the below precautions for using BP3595 as wireless equipment in U.S.A. 1) The label on the product is a certification label shown to be acquiring "FCC certification". Please do not put another label on the label. 2) If FCC ID is displayed on BP3595 cannot be seen from the outside of your product, the following displays (*) are needed for your product including BP3595. Contains Transmitter Module FCC ID: ANSBP3595 or Contains FCC ID: ANSBP3595

(*) The character size can be read easily is required. However it is not required more than 8 points. And also line break is not permit. 3) It is necessary to display the following texts on your product. (*) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

(*) If the text cannot be displayed on your product, you should describe in a manual or a package. It is foundations that the text is indicated on your product. REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 19/22 4) It is necessary to indicate all the texts applicable to the manual of your product. It is necessary text for all products. FCC CAUTION Change or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. It is necessary text for all products . 2 This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. It is necessary text for mobile product or portable product. A SAR examination is not required at mobile products (*) but is required at portable products (**).

(*) Mobile product The product is used separating from a human body over 20 cm.

(**) Portable product The product is used by human body within 20cm.

-1 It is necessary texts for a mobile product that is not required SAR examination if it is used by human body within 20cm. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). [But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from persons body.]

-2 It is necessary texts for a mobile product that is required SAR examination if it is used by human body within 20cm. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. It is necessary text for the product which is examined Hand SAR or uses always in hand but lower than limit of Hand SAR. excluding extremities: hands, wrists, feet and ankles

-3 It is necessary texts for a portable product that is not required SAR examination. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption rate (SAR). REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 20/22

-4 It is necessary texts for a portable product that is required SAR examination. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. [product name (model name)] has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. 23. PRECAUTIONS AS A WIRELESS EQUIPMENT 2 BP3595 acquired radio law certified in Canada (Industry Canada: IC). BP3595 is able to use in Canada without application of IC. IC20579-BP3595 Please following the below precautions for using BP3595 as wireless equipment in Canada. 1) The label on the product is a certification label shown to be acquiring "IC certification". Please do not put another label on the label. 2) If IC number is displayed on BP3595 cannot be seen from the outside of your product, the following displays (*) are needed for your product including BP3595. Contains Transmitter Module IC:20579-BP3595 or Contains IC:20579-BP3595

(*) The character size can be read easily is required. However it is not required more than 8 points. 3) It is necessary to indicate all the texts applicable to the manual of your product. It is necessary text for all products. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

()It is necessary to shown in English with French. REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 21/22 It is necessary text for mobile product or portable product. A SAR examination is not required at mobile products (*) but is required at portable products (**).

(*) Mobile product The product is used separating from a human body over 20 cm.

(**) Portable product The product is used by human body within 20cm.

-1 It is necessary texts for a mobile product that is not required SAR examination if it is used by human body within 20cm. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). [But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from persons body.]

Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise.

[Cependant, il est souhaitable qu'il devrait tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps.]

-2 It is necessary texts for a mobile product that is required SAR examination if it is used by human body within 20cm. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body (). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (). It is necessary text for the product which is examined Hand SAR or uses always in hand but lower than limit of Hand SAR. English: excluding extremities: hands, wrists, feet and ankles French: lexception des extrmits : mains, poignets, pieds et chevilles

-3 It is necessary texts for a portable product that is not required SAR examination. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption rate (SAR). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation du dbit dabsorption spcifique (DAS). REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free) TSZ2211105002 PRODUCTS HYBRID IC TYPE BP3595 PAGE 22/22

-4 It is necessary texts for a portable product that is required SAR examination. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. [product name (model name)] has been tested and found to comply with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. Les connaissances scientifiques dont nous disposons nont mis en vidence aucun problme de sant associ lusage des appareils sans fil faible puissance. Nous ne sommes cependant pas en mesure de prouver que ces appareils sans fil faible puissance sont entirement sans danger. Les appareils sans fil faible puissance mettent une nergie radiolectrique (RF) trs faible dans le spectre des micro-ondes lorsquils sont utiliss. Alors quune dose leve de RF peut avoir des effets sur la sant (en chauffant les tissus), lexposition de faibles RF qui ne produisent pas de chaleur na pas de mauvais effets connus sur la sant. De nombreuses tudes ont t menes sur les expositions aux RF faibles et nont dcouvert aucun effet biologique. Certaines tudes ont suggr quil pouvait y avoir certains effets biologiques, mais ces rsultats nont pas t confirms par des recherches supplmentaires. [product name (model name)] a t test et jug conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. 24. IMPORTANT NOTE BOTH FCC AND IC In the event that some conditions cannot be met (for example co-location with another transmitter), then the FCC /

IC authorization is no longer considered valid and the FCC / IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC / IC authorization. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.) 25. MANUAL INFORMATION TO THE END USER The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 26. ANTENNA RESTRICTION The antenna is designed as permanent attached and no consideration of replacement. TSZ2211105002 REV.B SPECIFICATION No.BP3595-B-001-E(Lead Free)