FCC ID: 2AGGZ003B9ACA4C DC 1.1Nm ARC Motor

MOTOR PROGRAMMING INSTRUCTIONS Li-ion & DC Motor SOFT STOP Live Feedback ELECTRONIC LIMIT Fav Position SELECTABLE SPEED 433 MHZ BI-DIRECTIONAL FAVORITE POSITION BATTERY CHECK USB CHARGE SOLAR OPTION LEVEL CONTROL

(Only for Li-ion Motor) BATTERY POWERED AUTOMATE V3.2_PRGM_APRIL_2022 SAFETY INSTRUCTIONS WARNING: Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturers liability and warranty. WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturers liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Do not expose to water, moisture, humid and damp environments or extreme temperatures. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. Follow installation instructions. For use with motorized shading devices. Keep away from children. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep clear when in operation. Replace battery with correctly specified type. COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installes doivent tre situes de facon ce que la population ne puisse y tre expose une distance de moin de 20 cm. Installer les antennes de facon ce que le personnel ne puisse approcher 20 cm ou moins de la position centrale de l antenne. La FCC des ltats-unis stipule que cet appareil doit tre en tout temps loign dau moins 20 cm des personnes pendant son functionnement. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 2 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA 12 BATTERY CHECK FUNCTION 12.1 Send Shade to battery charge level 13 CHARGING LED 13.1 Turn Charging LED ON/OFF 14 SLEEP MODE 15 TROUBLE SHOOTING 15 15 15 15 16 16 CONTENTS ASSEMBLY RETROFIT INSTALLATION CHARGING P1 BUTTON FUNCTIONS 1 2 3 4 4.1 Motor state test 4.2 Motor configuration options 5 INITIAL SET UP 5.1 Pair motor with controller 5.2 Check motor direction 5.3 Set Limits 6 ADJUSTING LIMITS 6.1 Adjust upper limit 6.2 Adjust lower limit 4 5 5 6 6 6 7 7 7 8 9 9 9 7 CONTROLLERS AND CHANNELS 10 7.1 Using P2 Button on existing controller to add a new controller or channel 10 7.2 Using a pre-existing controller to add or delete a controller or channel 10 8 FAVORITE POSITIONING 8.1 Set a favorite position 8.2 Send shade to favorite position 8.3 Delete favorite position 9 TILT & ROLLER MODE 9.1 Toggle motor to Tilt Mode 9.2 Toggle Motor to Roller Mode 10 ADJUSTING SPEED 10.1 Increase Motor Speed 10.2 Decrease Motor Speed 11 SOFT STOP CONFIGURATION 11.1 Turn Soft Stop OFF 11.2 Turn Soft Stop ON 11 11 11 11 12 12 12 13 13 13 14 14 14 ROLLEASE ACMEDA Automate Programming Instructions | Li-ion & DC Motors | 3 1 ASSEMBLY ZERO HEAD ADAPTER GENERIC CROWN, DRIVE & TUBE ASSEMBLY ZERO HEAD ANTENNA WRAP 4 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA 2 RETROFIT INSTALLATION

(1.1Nm & 2.0Nm MOTOR ONLY) 3 CHARGING/POWER SUPPLY

(LI-ION 1.1Nm & 2.0Nm ONLY)

(LI-ION 3.0Nm & 10.0Nm ONLY)

(DC 1.1Nm & 2.0Nm ONLY) ROLLEASE ACMEDA Automate Programming Instructions | Li-ion & DC Motors | 5 Requries a continuous 12V DC Power Source. 4 P1 BUTTON FUNCTIONS 4.1 Motor state test This table describes the function of a short P1 Button press/release (<2 seconds) depending on current motor configuration. P1 Press Condition Function Achieved Visual Feedback Audible Feedback Function Described If limit is NOT set None No Action None No Action If limits are set Short Press If motor is in Sleep Mode &

limits are set Operational control of motor, run to limit. Stop if running Wake and control 4.2 Motor configuration options Motor Runs None Operational control of motor after pairing and limit setting is completed first time Motor wakes and runs in a direction None Motor is restored from Sleep Mode and RF control is active The P1 Button is utilized to administer motor configurations as described below. Hold P1 button on motor head. Activate Pairing Mode Approx. Sleep Mode Approx. Approx. Reverse Direction Approx. Approx. Approx. 10 Reset To Factory Settings Approx. Approx. Approx. 10 Approx. P1 button on motor head. 6 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA 5 INITIAL SET UP 5.1 Pair motor with controller Select channel on controller. Hold P1 button on motor head. Hold STOP on controller. IMPORTANT Consult user manual for your controller for information on selecting channel. Motor Response Motor Response Approx. Motor is now in step mode and ready for setting limits 5.2 Check motor direction To check travel direction of shade, press UP or DOWN on controller. To reverse shade direction, hold both UP and DOWN. Until the motor responds. OR Quick Press = Step Long Press = Continuous Travel Motor Response Approx. IMPORTANT Damage to shade may occur when operating motor prior to setting limits. Attention should be given. IMPORTANT Reversing motor direction using this method is only possible during initial set-up ROLLEASE ACMEDA Automate Programming Instructions | Li-ion & DC Motors | 7 5.3 Set Limits IMPORTANT Cycle shade up and down prior to setting limits to settle fabric Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. To save upper limit, hold UP and STOP. OR Motor Response Approx. 5 SEC S Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. To save lower limit, hold DOWN and STOP. OR Motor Response Approx. 5 SEC S IMPORTANT After setting limits, motor will automatically exit from initial set-up mode. 8 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA 6 ADJUSTING LIMITS 6.1 Adjust upper limit Hold UP and STOP on controller. Move shade to the desired highest position by pressing the UP or DOWN button. To save upper limit, hold UP and STOP. OR Motor Response Approx. 5 SEC S Move shade to the desired lowest position by pressing the UP or DOWN button. To save lower limit, hold DOWN and STOP. OR Motor Response Approx. 5 SEC S Motor Response Approx. 5 SEC S 6.2 Adjust lower limit Hold DOWN and STOP on controller. Motor Response Approx. 5 SEC S IMPORTANT The bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is raised. ROLLEASE ACMEDA Automate Programming Instructions | Li-ion & DC Motors | 9 7 CONTROLLERS AND CHANNELS 7.1 Using P2 Button on existing controller to add a new controller or channel A = Existing controller or channel (to keep) B = Controller or channel to add or remove Press P2 on controller A. Press P2 on controller A. Press STOP on an new controller to add it. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor 7.2 Using a pre-existing controller to add or delete a controller or channel A = Existing controller or channel (to keep) B = Controller or channel to add or remove Press P2 on controller A. Press P2 on controller A. Press P2 on the controller B to remove it. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor 10 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA 8 FAVORITE POSITIONING 8.1 Set a favorite position Move shade to the desired position by pressing the UP or DOWN button on the controller. Press P2 on controller. Press STOP on controller. Press STOP on controller. OR Motor Response Motor Response Motor Response 8.2 Send shade to favorite position Approx. 8.3 Delete favorite position Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response ROLLEASE ACMEDA Automate Programming Instructions | Li-ion & DC Motors | 11 9 TILT & ROLLER MODE 9.1 Toggle motor to Tilt Mode Default motor mode is Roller after initial Limits have been set, use following steps to change to Roller Mode. Hold UP & DOWN on controller. Press STOP on controller. Motor Response Motor Response Approx. 5 SEC S 9.2 Toggle Motor to Roller Mode If motor is in Tilt Mode, use following steps to change to Roller Mode. Hold UP & DOWN on controller. Press STOP on controller. Motor Response Motor Response Approx. 5 SEC S 12 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA 10 ADJUSTING SPEED 10.1 Increase Motor Speed Default motor mode is the slowest speed. Press P2 Press UP Press UP Motor Response Motor Response Motor Response 10.2 Decrease Motor Speed Press P2 Press DOWN Press DOWN Motor Response Motor Response Motor Response ROLLEASE ACMEDA Automate Programming Instructions | Li-ion & DC Motors | 13 11 SOFT STOP CONFIGURATION 11.1 Turn Soft Stop OFF Motor must be in slowest speed to turn Soft Stop OFF. Press P2 Press DOWN Press DOWN Motor Response Motor Response Motor Response 11.2 Turn Soft Stop ON Motor must be in fastest speed to turn Soft Stop ON. Press P2 Press UP Press UP Motor Response Motor Response Motor Response 14 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA 12 BATTERY CHECK FUNCTION 12.1 Send Shade to battery charge level Shade must be at Upper Limit. Hold UP Upper Limit Percentage of Battery Charge Remaining Lower Limit Percentage Depleted Motor Response Approx. SEC5 Shade must be at Upper Limit Hold UP for Approx. 5s Shade moves to percentage of battery charge remaining NOTE: This feature is can only be used with a DC motor when it is using a Barrery Pack as its power source. 13 CHARGING LED

(ONLY FOR LI-ION MOTORS) 13.1 Turn Charging LED ON/OFF Motor must be at Lower Limit. Hold DOWN to toggle off Hold DOWN to toggle on CHARGING LED STATUS SOLID GREEN Motor is fully charged Motor Response Motor Response Approx. 5 SEC S Red LED flashes x3 Approx. 5 SEC S Red LED flashes x3 BLINKING GREEN Motor is charging. Battery is greater than 50%. BLINKING GREEN & RED Motor is charging. Battery is lower than 50%. ROLLEASE ACMEDA Automate Programming Instructions | Li-ion & DC Motors | 15 14 SLEEP MODE 9 SLEEP MODE If multiple motors are grouped on a single channel, Sleep Mode may be used to put all but 1 motor to sleep, allowing programming of just the one motor that remains Awake. See page 6 for detailed P1 functions. Enter Sleep Mode Sleep mode is utilized to prevent a motor from incorrect configuration during other motor setup. Hold P1 button on the motor head Exit Sleep Mode: Method 1 Exit Sleep Mode: Method 2 Exit sleep mode once the shade is ready. Remove power and then re-power the motor. Press and release P1 button on the motor head Motor Response Motor Response Approx. G 15 TROUBLE SHOOTING automateshades.com Problem Cause Remedy Motor is not responding Battery in motor is depleted or Power Supply is not working Recharge with a compatible charger Insufficient charging from solar PV panel Check connection and orientation of PV panel Transmitter battery is discharged Replace battery Battery is inserted incorrectly into transmitter Radio interference/shielding Check battery polarity Ensure transmitter is positioned away from metal objects and the aerial on motor or receiver is kept straight and away from metal Receiver distance is too far from transmitter Move transmitter to a closer position Charging failure Motor beeps x10 when in use Battery voltage is low Cannot program a single motor

(multiple motors respond) Multiple motors are paired to the same channel Check power supply to motor is connected and active Recharge with a compatible charger Always reserve an individual channel for programming functions. Use Sleep Mode to program individual motors. ROLLEASE ACMEDA | USA Level 7 / 750 East Main Street Stamford, CT 06902, USA ROLLEASE ACMEDA | AUSTRALIA ROLLEASE ACMEDA | EUROPE 110 Northcorp Boulevard, Broadmeadows VIC 3047, AUS Via Conca Del Naviglio 18, Milan (Lombardia) Italy T +1 800 552 5100 | F +1 203 964 0513 T +61 3 9355 0100 | F +61 3 9355 0110 T +39 02 8982 7317 | F +39 02 8982 7317 16 | Automate Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

DC 1.1 ARC Motor

[025mm/1.INM/20rpm]($45) MTOV-1225-069004-S brad @ UK FCC ID: 2AGGZOO3B9ACAAC @- ca IC: 21769-003894CAAC . 5005833 y

43392MHz [0.834] 10W |0.25kg] 1P20 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. DC 1.1 ARC Motor

[@25mm/11INm/20rpm]SKY) TO}1225-069002-S ARC 23" onus Mr HS Ae sce azo l). Taos [maoewenc]ica| enn] meek CeO 43392MHz |0.83A| 1ow |0.25kq| 1P20 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Rollease Acmeda Inc Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-29-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID:2AGGZ003B9ACA4C Rollease Acmeda Inc.certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information:

FRN: 0025043381 Name: Rollease Acmeda Inc Address: 7th Floor / 750 East Main Street,Stamford, CT 06902, USA Contact Person: Jonny.Matuichuk Tel.:2034906191 Email:jonny.matuichuk@rolleaseacmeda.com Sincerely, Jonny.Matuichuk Rev 1/26/2023

Rollease Acmeda Inc Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-29-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AGGZ003B9ACA4C Rollease Acmeda Inc.certifies that the equipment for which authorization is sought is notcovered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Applicantsignature:

Applicant printed name:Jonny.Matuichuk Rev 1/26/2023

Rollease Acmeda Inc Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-29-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AGGZ003B9ACA4C Rollease Acmeda Inc.certifiesthat, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Applicant signature:

Applicant printed name:Jonny.Matuichuk

Rollease Acmeda Inc Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID:2AGGZ003B9ACA4C

. Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type

(Block Diagram, Schematics, Operation description) File Name

(Block Diagram, Schematics, Operation description.pdf) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type

(Internal Photos, Test Setup Photos, User manual) File Name

(Internal Photos, Test Setup Photos, User manual.pdf) Number of days: 180 days Sincerely,

(signature)

(printed name)Jonny.Matuichuk Rev 11/20/07

To whom it may concern, Letter of Declaration We, Rollease Acmeda Inc, hereby declare the models below:

Model(S):

MT01-1225-069002-S, MT01-1225-069004-S FCC ID:

IC ID:

2AGGZ003B9ACA4C 21769-003B9ACA4C are identical in electrical and mechanical construction except for the model number, and end-cap adaptor. For the end cap adaptor, the only change is the adaptors profile as shown in the below table:

Print name: Jonny Matuichuk Title:

Product Manager Signature /Date:

25/05/2023 1 of 1 RA CodeDescriptionMT01-1225-069002-SAUTOMATE | DC 1.1Nm ARC Motor[25/12V/20rpm](SKY)MT01-1225-069004-SAUTOMATE | DC 1.1Nm ARC Motor[25/12V/20rpm](S45)AdaptorDC 25 Motor

Rollease Acmeda Inc Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: May 29,2023 SUBJECT: FCC Application for FCC ID:2AGGZ003B9ACA4C To Whom It May Concern:

We, the undersigned, hereby authorize Yu Anlu at TV SD Certification and Testing

(China) Co., Ltd. Shanghai Branch on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by TV SD Certification and Testing (China) Co., Ltd. Shanghai Branch on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, PrintedName: Jonny.Matuichuk Signature C:\Users\jonny.matuichuk\Downloads\Certification\More\FCC IC application Form-1225 mm Motors\FCC IC application Form-1225 mm Motors\FCC POA _Letter.docx

RolleaseAcmeda Inc Date:2023-05-29 To: Federal Communications Commission 7435 Oakland Mills Road Columbia MD FCC ID:2AGGZ003B9ACA4C To Whom It May Concern:

This letter is to ascertain that RolleaseAcmeda Inc Product name: Tubular Motor, Model: MT01-1225-069002-S, MT01-1225-069004-S have been the units used for conducting FCC compliance testing, the SDoC part will be tested by FCC recognized test lab. If you have any question or concerns, please contact us. Sincerely, Signature Company name:RolleaseAcmeda Inc Address:7th Floor / 750 East Main Street,Stamford, CT 06902, USA E-mail:jonny.matuichuk@rolleaseacmeda.com Tel:2034906191 Printed Name:Jonny.Matuichuk