FCC ID: 2AGGZMTACRFDR50KG Electronic Limit - AC Curtain Motor

AUTOMATE C 1.2 MTACRFDR-50KG - ARC DRAPERY MOTOR 433 MHZ BI-DIRECTIONAL ELECTRONIC LIMIT FAVORITE POSITION LEVEL CONTROL SOFT TOUCH QUIET OPERATION AUTOMATE | ARC drapery motor is compatible with popular drapery track systems for easy incorporation of draperies into the ARC motorized platform. The Soft Touch feature enables manual operation when needed. Leveling Control allows for precise positioning of individual or multiple drapes ensuring perfect alignment every time. Additionally, a favorite position can be pre-set and recalled at any time. FEATURES:

Electronic Torque sensing Autoset Limits 433 MHz Bi-Directional RF Communication Leveling Control Favorite Position Soft start / stop Soft touch control Top exit option for power cord I 7 1 0 2 L R P A 0

. 1 V G K 0 5

R D F R C D T M

. R T S N I NOTES 2 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA CONTENTS ASSEMBLY 1 2 P1 BUTTON FUNCTIONS 2.1 Motor State Test 2.2 Motor Configuration Options 3 INITIAL SET-UP 3.1 Pair motor with controller 3.2 Check motor direction 3.3 Set limits 4 ADJUSTING LIMITS 4.1 Adjust upper/open limit 4.2 Adjust lower/close limit 5.1 Using motor P1 button 5.2 Using a pre-exisiting controller 6 FAVORITE POSITIONING 6.1 Set a favorite position 6.2 Send shade to favorite position 6.3 Delete favorite position 7 ADJUSTING MOTOR SPEED 7.1 Increase or decrease motor speed 8 SLEEP MODE 8.1 Enter sleep mode 8.2 Exit sleep mode 9 TROUBLESHOOTING 5 ADDING OR REMOVING CONTROLLERS AND CHANELS 5 6 6 6 7 7 7 8 9 9 9 10 10 10 11 11 11 12 12 12 13 13 13 14 3 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA SAFTEY INSTRUCTIONS WARNING: Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturers liability and warranty. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. Ensure correct crown and drive adaptors are used for the intended system. Do not cut the antenna. For use within tubular blinds. Do not allow children to play with this device. Keep antenna straight and clear from metal objects Do not expose to moisture or extreme temperatures. CAUTION Motor is to be installed in horizontal application only. If cable or power connector is damaged do not use. Use only Rollease Acmeda hardware. Do not drill into motor body. The routing of cable through walls shall be protected by isolating bushes or grommets. Ensure power cable and aerial is clear and protected from moving parts. Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation. Ensure torque and operating time is compatible with end application. Do not expose the motor to water or install in humid or damp environments. Important safety instructions to be read prior to operation. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. should not be allowed to use this product. Keep remote controls away from children. Keep motor away from acid and alkali. Do not force the motor drive. Keep clear when in operation. Do not dispose of in general waste. 4 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 1 ASSEMBLY The Automate ARC Drapery motor works with most major drapery track systems. Follow the below instructions to simply retrofit with the Drive Pulley* to an existing track *Drive Pulley Available Seperately NOTE: DISASSEMBLE EXISTING DRAPERY TRACK PRIOR TO FOLLOWING ASSEMBLY STEPS STEP 1 Install drapery drive belt into new drive housing & assemble drive housing components. It is recommende to that both pulleys be replaced to allow for installation of motor on either end. Assemble drive belt attachments and attach drive housing to track. Repeat steps 1-2 for Idler Side STEP 2:

STEP 3:

STEP 4:

STEP 5:

Assemble Brackets, Runners, Stoppers & Idler Drive Unit Cover. Assemble Drapery Motor to drive housing. Ensure Fixing Pin is engaged securely and motor is secured to housing. Plug motor into wall recepticle NOTE: Motor power cable may be shortened and/or routed through the motor body to exit the top of the track. This requires using a field installed plug to replace the motor grounding plug. 5 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 2 P1 BUTTON FUNCTIONS 2.1 Motor State Test This table describes the function of a short P1 button press/release(<2 seconds) depending on current motor configuration. P1 Press Short Press then Release

(<2 sec) Condition Function Achieved Visual Feedback Audible Feedback Function Described If limit is NOT set None No Action None No Action If limits are set Operational control of motor, run to Motor runs None limit. Stop if running Operational control of motor after pairing and limit setting is completed first time If motor is in Sleep Mode &

limits are set

(Refer to Sec.10) Wake and control Motor wakes and runs in a direction Motor is restored from None Sleep mode and RF control is active 2.2 Motor Configuration Options The P1 Button is utilized to administer motor configuration as described below and beginning in Section 4. Hold P1 P1 GREEN LED Activate Pairing Mode Approx. Motor Response RELEASE P1 Sleep Mode Approx. Motor Response RELEASE P1 Non-Functional Connectors For Future Use Reverse Direction Programming LED Approx. Motor Response RELEASE P1 Reset To Factory Settings Approx. Motor Response 6 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 3 INITIAL SET-UP 3.1 Pair motor with controller Select channel on controller.

(Disregard if using single channel controller) Hold P1 button on motor Hold STOP on controller IMPORTANT Motor Response Motor Response Consult user manual for your controller for information on selecting channel. RELEASE P1 Approx. Motor is now in setup mode and ready for setting limits. 3.2 Check motor direction For correct operation UP should open Drapery and DOWN should close. To check travel direction of shade, press To reverse shade direction, hold both UP UP or DOWN on controller. and DOWN until motor responds Quick Press = Step Motor Reponse Long Press = Continuous Travel 7 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA Reversing motor direction using this method is only possible during initial set-up, prior to first time limit setting, or after a re-set of motor 3.3 Set limits The AUTOMATE drapery motor features automatic limit detection. Once the motor is attached to a fabricated, installed track, limits can be set with a few simple actions. Press the UP or DOWN buttons on controller. Carrier will run to the end of the track. When carrier has reached the end of the track, it will automatically set limit there. Repeat for opposite end. IMPORTANT To verify limits were successfully set, press up or down to run to limit. Motor should now function with slow start/

slow stop feature. Initial set-up is now complete 8 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 4 ADJUSTING LIMITS 4.1 Adjust upper/open limit Press & hold UP/OPEN and STOP on Controller until the motor responds. Move shade to the desired To save upper limit, hold UP/OPEN and upper position by pressing the STOP until the motor responds. UP/OPEN or DOWN button. Motor Response Motor Response Approx. Approx. 4.2 Adjust lower/close limit Hold DOWN/CLOSE and STOP on controller. Move shade to the desired lowest position by pressing the UP or DOWN/CLOSE button To save lower limit, hold DOWN/CLOSE and STOP. Motor Response Approx. Motor Response Approx. 9 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 5 ADDING OR REMOVING CONTROLLERS AND CHANELS 5.1 Using motor P1 button Hold P1 button on motor head. Hold STOP on controller to add or remove Motor Response Motor Response RELEASE P1 Approx. 5.2 Using a pre-exisiting controller A= Exisiting controller or channel (to keep) B= Controller or channel or add or remove Press P2 on exisiting controller. Press P2 on exisiting controller. Press P2 on new controller. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor. 10 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 6 FAVORITE POSITIONING 6.1 Set a favorite position Move shade to the desired position by pressing the UP or DOWN button on the controller. Press P2 on controller. Press STOP on controller. Press STOP controller. Motor Response Motor Response Motor Response 6.2 Send shade to favorite position Hold STOP on controller until motor begins moving, then release. Approx. 11 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 6.3 Delete favorite position Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response 7 ADJUSTING MOTOR SPEED 7.1 Increase or decrease motor speed Press P2 on controller. Press UP Press UP Press DOWN Press DOWN Motor Response Motor Response Motor Response 12 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA IMPORTANT If motor does not react to speed adjustment, the maximum or minimum speed has already been reached. 8 SLEEP MODE 8.1 Enter sleep mode Sleep mode is used to disable the Radio in the motor, thus it will not react to radio commands when this mode is activated. This feature is useful for administering motor programing functions when the motor is paired to the same channel as other motors. Hold P1 button on motor head. Motor Response Approx. Motor Response RELEASE P1 8.2 Exit sleep mode Exit sleep mode once installation is complete. TUG on Drape master carrier to activate the motor PRESS & RELEASE P1 button on motor head. Motor Response Approx. MOTOR RUNS TO LIMIT 13 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA 9 TROUBLESHOOTING Problem Cause Remedy Motor is not responding Radio interference/shielding A / C power supply not plugged in. Check motor to power cable connection and AC plug. Transmitter battery is discharged Replace battery Battery is inserted incorrectly into transmitter Check battery polarity Receiver distance is too far from transmitter Move transmitter to a closer position Power failure Incorrect wiring Ensure transmitter is positioned away from metal objects and the aerial on motor or receiver is kept straight and away from metal Check power supply to motor is connected and active Check that wiring is connected correctly (refer to motor installation instructions) Always reserve an individual channel for programming functions SYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi motor projects, that provides individual control for each motor for programming purposes Place all other motors into sleep mode (ref to P1 function overview

- section 2.2 and section 8) Cannot program a single Motor

(multiple motors respond) Multiple motors are paired to the same channel. 14 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Queensland Branch Unit 2/62 Borthwick Avenue, Murarrie QLD 4172 ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 | F +61 3 9355 0110 ROLLEASE ACMEDA USA 200 Harvard Avenue Stamford, CT 06902 6320 T +1 203 964 1573 | F +1 203 964 0513 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan

(Lombardia) Italy T +39 02 8982 7317 | F +39 02 8982 7317 info@rolleaseacmeda.com rolleaseacmeda.com 15 | Automate Programming Instructions | ARC Drapery Motor

MTACRFDR-5OKG | v1.3 Product Label 85x35mm DRP 1.2 Electronic Limit - AC Curtain Motor

(1.2Nm-1cm/s} ARG) MTACRFDR-5SOKG| 3 FCC ID: 24GGZMTACRFDRSOKG Too12a AG | WABEIN PRE IC: 21769-MTACRFDR50K Cavanefrl ox [om QyCE FE ee

Attention: Application Examiner / Review Engineer Subject: Request to change in identification per section 2.933 of FCC rules and Multiple Listing of Certification service per clause 11.5 of RSP-100 Reference: FCC ID: 2AGGZMTACRFDR50KG and IC: 21769-MTACRFDR50K Statement from applicant On the behalf of Rollease Acmeda Inc I am writing to apply for certification of the following product from our company:

Grantee name: Rollease Acmeda Inc Model / HVIN & PMN name: MTACRFDR-50KG FCC ID: 2AGGZMTACRFDR50KG IC: 21769-MTACRFDR50K The above product, for which we are applying for certification, is identical to the following product:

Grantee name: NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Granted date of FCC and IC: 1/6/2020 and 1/9/2020 Model / HVIN & PMN name: DT12TV/S-1.2/14 Original FCC ID: VYY-DT12TVS1214 Original IC: 21396-DT12TVS1214 in design, circuitry and construction except for trade name, model number and logo. The documents on file with FCC/ISED from the original certification remain unchanged and continue to be valid, except for user manual and label location. As a result, the original test results of above FCC ID and IC granted product continue to be representative of and applicable to the product from our company for certification. Date: Sep 10, 2020

Attention: Application Examiner / Review Engineer Subject: Authorization for changing FCC / IC identifier Reference: FCC ID: 2AGGZMTACRFDR50KG and IC: 21769-MTACRFDR50K On the behalf of NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. (original Grantee / certificate holder), I authorize the following Grantee name: NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Granted date of FCC and IC: 1/6/2020 and 1/9/2020 Model / HVIN & PMN name: DT12TV/S-1.2/14 Original FCC ID: VYY-DT12TVS1214 Original IC: 21396-DT12TVS1214 to be changed FCC / IC identifier as:

Grantee name: Rollease Acmeda Inc Model / HVIN & PMN name: MTACRFDR-50KG FCC ID: 2AGGZMTACRFDR50KG IC: 21769-MTACRFDR50K It was authorized Rollease Acmeda Inc to use documents among the existing FCC and IC certification for Multiple Listing of Certification / identification change. The new product should be same as the one from my company in design, circuitry and construction except for trade name, model number and logo.

Authority to Act as Agent Date: __Jan 11, 2019 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Intertek Testing Service Shanghai is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: Dec 31, 2019 By: oo Ay Jere _Gianola

(Signature!) (Print name) a Title: [Roger NANI ge - Notun tnt ud On behalf of: Rollease Acmeda Inc

(Company Name) Telephone: +1 - 20 3- Wb4-1593 Dec 30, 2020