FCC ID: 2AGGZMTDCBRFQ453 Electronic Limit - Tubular DC Rechargeable Battery Motor

AUTOMATE Li-ion ARC TUBULAR MOTOR 433 MHZ BI-DIRECTIONAL ELECTRONIC LIMIT SELECTABLE RPM FAVORITE POSITION LEVEL CONTROL WIREFREE SOLAR POWERED AUTOMATE | Li-ion ARC motors offer a wirefree rechargeable easy to use and program solution to suit a large range of applications, torques and speeds. The Leveling Control feature allows for precise positioning of multiple shades ensuring perfect alignment. Additionally, a favorite position can be pre-set and recalled at any time. FEATURES:

Electronic Limits 433 MHz Bi-Directional RF Communication Leveling Control 3 x Selectable Rpm Favorite Position Roller & Tilt Modes. 6 1 0 2 E N U J 2

. 1 V F R B C D T M

. R T S N I NOTES 2 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA CONTENTS 1 ASSEMBLY 2 WIRING 2.1 Charging options 3 4 P1 BUTTON FUNCTIONS INTIAL SET-UP 4.1 Pair motor with controller 4.2 Check motor direction 4.3 Set limits 5 ADJUSTING LIMITS 5.1 Adjust upper limit 5.2 Adjust lower limit 6 ADDING OR REMOVING CONTROLLERS AND CHANNELS 6.1 Using motor P1 button 6.2 Using a pre-existing controller 7 FAVORITE POSITIONING 7.1 Set a favorite position 7.2 Send shade to favorite position 7.3 Delete favorite position 8 ADJUSTING MOTOR SPEED 8.1 Increase or decrease motor speed 9 TILT & ROLLER MODE 9.1 Enter tilt mode 9.2 Enter roller mode (Default) 10 TROUBLESHOOTING 5 6 6 7 8 8 8 9 10 10 10 11 11 11 12 12 12 12 13 13 14 14 14 15 3 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA SAFTEY INSTRUCTIONS WARNING: Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturers liability and warranty. Do not expose to moisture or extreme temperatures. Do not allow children to play with this device. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. For use within tubular blinds. Ensure correct crown and drive adaptors are used for the intended system. Keep antenna straight and clear from metal objects Do not cut the antenna. Use only Rollease Acmeda hardware. Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation. Ensure torque and operating time is compatible with end application. Do not expose the motor to water or install in humid or damp environments. CAUTION Motor is to be installed in horizontal application only. Do not drill into motor body. The routing of cable through walls shall be protected by isolating bushes or grommets. Ensure power cable and aerial is clear and protected from moving parts. If cable or power connector is damaged do not use. Important safety instructions to be read prior to operation. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product. Keep remote controls away from children. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep motor away from acid and alkali. Do not force the motor drive. Keep clear when in operation. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 4 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 1 ASSEMBLY Please refer to Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used. Step 1. Cut roller tube to required length. Step 2. Ensure roller tube is clean and free from burrs. Step 3. Fit required crown, drive and bracket adapters. Tube must be close fitting with chosen crown and drive adapters. Refer to Rollease Acmeda System Assembly Manual for recommended crown, drive, and bracket adapter kits. Crown Retaining Clip Drive Step 4. Slide Motor into tube. Insert by aligning keyway in crown and drive wheel to the tube. Step 5. Mount motorized tube onto brackets. Refer to Rollease Acmeda System Assembly Manual for recommended crown, drive, and bracket adapter kits. Motor Head Adapter Bracket 5 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 2 WIRING 2.1 Charging options This motor has a 12V built in Li-ion battery pack with integrated charge management. Max power input for recharging: 12.6V / 1000mAh. Before first use please charge motor for 6 hours. Using the reccomended AC charger. During operation, if voltage drops to less than 10V, the motor will beep 10 times to prompt it needs to be charged. Motor will stop running when the voltage is lower than 7V and it will resume again when the voltage is greater than 7.5V. AC Charger ITEM NO.:

# MTDCB-CHARGE-US

# MTDCB-CHARGE-AU

# MTDCB-CHARGE-EU Solar Panel ITEM NO.:

#MTSOLPAN-B Ensure cable is kept clear of fabric. Ensure antenna is kept straight and away from metal objects. 6 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA Audible Feedback Function Described None None None No Action Operational control of motor after pairing and limit setting is completed first time Motor is restored from Sleep Mode and RF control is active 3 P1 BUTTON FUNCTIONS P1 Press Condition Function Achieved If limit is NOT set If limits are set None Operational control of motor, run to limit. Stop if running Short Press Visual Feedback No Action Motor runs If motor is in Sleep Mode &

limits are set Wake and control Motor wakes and runs in a direction Hold P1 P1 Activate Pairing Mode Approx. Motor Response Sleep Mode Approx. Motor Response Reverse Direction Approx. Motor Response Reset To Factory Settings Approx. Motor Response 7 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 4 INTIAL SET-UP 4.1 Pair motor with controller Select channel on controller. Hold P1 button on motor head. Hold STOP on controller. IMPORTANT Motor Response Motor Response Consult user manual for your controller for information on selecting channel. Motor is now in step mode and ready for setting limits 4.2 Check motor direction To check travel direction of shade, press UP or DOWN on controller. To reverse shade direction, hold both UP and DOWN. Quick Press = Step Long Press = Continuous Travel Motor Response IMPORANT Damage to shade may occur when operating motor prior to setting limits. Attention should be given. IMPORTANT Reversing motor direction using this method is only possible during initial set-up. 8 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 4.3 Set limits To save upper limit, hold UP and STOP. Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. To save lower limit, hold DOWN and STOP. IMPORTANT Motor Response Cycle shade up and down prior to setting limits to settle fabric 5 SECS IMPORTANT After setting limits, motor will automatically exit from initial set-up mode. Initial set-up is now complete 9 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 5 ADJUSTING LIMITS 5.1 Adjust upper limit Hold UP and STOP on controller. Motor Response 5 SECS 5.2 Adjust lower limit Hold DOWN and STOP on controller. Move shade to the desired highest position by pressing the UP button. Move shade to the desired lowest position by pressing the DOWN button. To save upper limit, hold UP and STOP. Motor Response 5 SECS To save lower limit, hold DOWN and STOP. Motor Response 5 SECS Motor Response 5 SECS 10 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 6 ADDING OR REMOVING CONTROLLERS AND CHANNELS 6.1 Using motor P1 button Hold P1 button on motor head. Hold STOP on controller to add or remove. Motor Response Motor Response 6.2 Using a pre-existing controller Press P2 on existing controller. Press P2 on existing controller. Press P2 on new controller. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor. 7 FAVORITE POSITIONING 7.1 Set a favorite position Move shade to the desired position by pressing the UP or DOWN button on the controller. Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response 7.2 Send shade to favorite position Hold STOP on controller. 7.3 Delete favorite position Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response 12 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 8 ADJUSTING MOTOR SPEED 8.1 Increase or decrease motor speed Press UP. Press UP. Press P2 on controller. Press DOWN. Press DOWN. Motor Response Motor Response Motor Response IMPORTANT If motor does not react to speed adjustment, the maximum or minimum speed has already been reached. 13 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 9 TILT & ROLLER MODE 9.1 Enter tilt mode Hold UP and DOWN on controller. Press STOP. Motor Response Motor Response 5 SECS 9.2 Enter roller mode (Default) Hold UP and DOWN on controller. Press STOP. Motor Response Motor Response 5 SECS 10 TROUBLESHOOTING Problem Cause Battery in motor is depleted Remedy Recharge with compatible AC adaptor and check connection and positioning of PV panel. Check connection and orientation of PV panel. Insufficient charging from Solar

(PV) Panel Transmitter battery is discharged Replace battery Battery is inserted incorrectly into transmitter Check battery polarity Motor is not responding Radio interference/shielding Receiver distance is too far from transmitter Power failure Incorrect wiring Motor beeps 10 times when in use Battery voltage is low / PV (solar) panel issue Cannot program a single Motor

(multiple motors respond) Multiple motors are paired to the same channel. Ensure transmitter is positioned away from metal objects and the aerial on motor or receiver is kept straight and away from metal Move transmitter to a closer position Check power supply to motor is connected and active Check that wiring is connected correctly (refer to motor installation instructions) Recharge with AC adaptor or check connection and positioning of PV pane Always reserve an individual channel for programming functions SYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi motor projects, that provides individual control for each motor for programming purposes Place all other motors into sleep mode (ref to P1 function overview

- section 3) 15 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Western Australia Branch Unit 1, 41 Mulgul Road, Malaga WA 6090 T +61 8 9248 5571 | F +61 8 9248 5572 Queensland Branch Unit 2/62 Borthwick Avenue, Murarrie QLD 4172 ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 | F +61 3 9355 0110 ROLLEASE ACMEDA USA 200 Harvard Avenue Stamford, CT 06902 6320 T +1 203 964 1573 | F +1 203 964 0513 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan

(Lombardia) Italy T +39 02 8982 7317 | F +39 02 8982 7317 info@rolleaseacmeda.com rolleaseacmeda.com 16 | Automate Programming Instructions | Tubular Li-ion Motors

Attention: Application Examiner / Review Engineer Subject: Request to change in identification per section 2.933 of FCC rules and Multiple Listing of Certification service per clause 11.5 of RSP-100 Reference: FCC ID: 2AGGZMTDCBRFQ453 and IC: 21769-MTDCBRFQ453 Statement from applicant On the behalf of Rollease Acmeda Inc I am writing to apply for certification of the following product from our company:

Grantee name: Rollease Acmeda Inc Model / HVIN & PMN name: MTDCBRFQ45-3 FCC ID: 2AGGZMTDCBRFQ453 IC: 21769-MTDCBRFQ453 The above product, for which we are applying for certification, is identical to the following product:

Grantee name: NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Granted date of FCC and IC: 06/21/2016 and 11/08/2019 Model / HVIN & PMN name: DM45LEQ/S-3/28 Original FCC ID: VYYDM451009 Original IC: 21396-DM451009 in design, circuitry and construction except for trade name, model number and logo. The documents on file with FCC/ISED from the original certification remain unchanged and continue to be valid, except for user manual and label location. As a result, the original test results of above FCC ID and IC granted product continue to be representative of and applicable to the product from our company for certification. Date: Nov 10, 2019

Attention: Application Examiner / Review Engineer Subject: Authorization for changing FCC / IC identifier Reference: FCC ID: 2AGGZMTDCBRFQ453 and IC: 21769-MTDCBRFQ453 On the behalf of NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. (original Grantee / certificate holder), I authorize the following Grantee name: NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Granted date of FCC and IC: 06/21/2016 and 11/08/2019 Model / HVIN & PMN name: DM45LEQ/S-3/28 Original FCC ID: VYYDM451009 Original IC: 21396-DM451009 to be changed FCC / IC identifier as:

Grantee name: Rollease Acmeda Inc Model / HVIN & PMN name: MTDCBRFQ45-3 FCC ID: 2AGGZMTDCBRFQ453 IC: 21769-MTDCBRFQ453 It was authorized Rollease Acmeda Inc to use documents among the existing FCC and IC certification for Multiple Listing of Certification / identification change. The new product should be same as the one from my company in design, circuitry and construction except for trade name, model number and logo.

Rollease Acmeda Inc Authority to Act as Agent Date: Jul 15, 2019 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

_____Intertek Testing Service Shanghai______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____Dec 31, 2020 By:

Title:

On behalf of: __ Rollease Acmeda Inc ________________ Telephone:

_____ Jere Gianola __________________ ______Program Manager____________________ _____ 41-203-964-1573 ___________________

(Print name)

(Company Name)

(Signature1) 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

GRANT OF EQUIPMENT C T C B AUTHORIZATION T B Certification Issued Under the Authority of the Federal Communications Commission By:

TUV SUD BABT Octagon House, Concorde Way, Date of Grant: 06/21/2016 Segensworth North, Fareham, PO15 5RL Application Dated: 06/21/2016 United Kingdom NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. LOUTOU INDUSTRIAL AREA, ZHENHAI NINGBO ZHEJIANG, China Attention: Qiwei Zhang , MANAGER NOT TRANSFERABLE EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. FCC IDENTIFIER: YY YDM451009 Name of Grantee: NINGBO DOOYA MECHANIC &

ELECTRONIC TECHNOLOGY CO., LID. Equipment Class: Part 15 Security/Remote Control Transmitter Notes: Tubular Motor Frequency Output Frequency Emission Grant Notes FCC Rule Parts Range (MHZ) Watts Tolerance Designator 15.231 433.925 - 433.925 Output power is peak conducted.