AUTOMATE Interior Sun Sensor 433 MHz Internal sun sensor for automatic shade control. FEATURES:
3 Modes of operation:
- Close Mode
- Open / Close Mode
- Shade Detect Mode 4 Light sensitivity levels Low battery warning 6 1 0 2 Y L U J 1
. 1 V S N E S N U S
-
F R T M
. R T S N I CONTENTS TECHNICAL DATA / PACK CONTENTS SAFETY INSTALLATION 1 2 3 3.1 Sensor battery 3.2 Replacing battery 3.3 Mounting 4 FUNCTIONAL OVERVIEW 4.1 Buttons 4.2 Modes 4.3 View and change sensor mode 4.4 Light levels of light intensity values 4.5 Light intensity detection 4.6 Low battery notification 4.7 UP button 5 PROGRAMMING 5.1 Protocol selection 6 ADDING OR REMOVING SENSOR & CREATING GROUP CONTROL 6.1 Using Motor P1 Button 6.2 Using a pre-existing Controller 7 8 TROUBLESHOOTING NOTES 3 4 5 5 5 5 6 6 6 7 7 7 7 7 8 8 9 9 9 10 11 2 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA 1 TECHNICAL DATA / PACK CONTENTS TECHNICAL SPECIFICATIONS 3V (CR2032) 5uA 433.92 MHz 10 milliwatt
-10C -50C 15 - 75 Klux up to 200 meters (open space) Voltage:
Standby Current:
Frequency:
Transmitting Power:
Ambient Operating Temperature:
Light Intensity Level Range:
Transmission Distance:
PACK CONTENTS 1 x Sun Sensor 1 x Instruction Manual 1 x 3V - CR2032 Battery ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 3 2 SAFETY WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturers liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Do not expose to water, moisture, humid and damp environments or extreme temperatures. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. Follow installation instructions. For use with motorized shading devices. Keep away from children. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep clear when in operation. Replace battery with correctly specified type. Rollease Acmeda declares this equipment is in compliance with the essential requirements and other relevant provisions of R&TT EC Directive 1999/5/EC This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which Can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 4 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA 3 INSTALLATION 3.1 Sensor battery Pull battery tab out to activate for first use. 3.2 Replacing battery Pry open using flat head screw driver where notches meet on the sensor. Remove old battery by pressing up from under the batterys position. Push new battery in with the +
facing outwards. Replace cover by aligning notches and press together. 3.3 Mounting 1. Ensure surface on glass is clean and free of dust. 2. On the back of the sensor, peel clear plastic off to reveal adhesive. 3. Find desired position on glass for the sensor and press adhesive side to glass. ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 5 4 FUNCTIONAL OVERVIEW 4.1 Buttons Light Level Indicator Up P2 Change Light Level 4.2 Modes Mode 1 - DEFAULT Close Mode Mode 2 Mode 3 Open / Close Mode Shade Detect Mode Pre-set light level reached Pre-set light level reached Pre-set light level reached Light level stays above pre-set for 2 mins Light level stays above pre-set for 2 mins Light level stays above pre-set for 2 mins Blind goes down Blind goes down Blind stays down Light < pre-set for >15 mins Blind goes down until sensor is covered Blind goes up until sensor is uncovered Blind goes back up Light < pre-set for > 15 mins Blind goes back up 6 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA 4.3 View and change sensor mode To view the current mode, press the SUN button for one second 1 blink indicates mode 1 2 blinks indicate mode 2 3 blinks indicate mode 3 To change the mode:
Hold the SUN button until the LED blinks 5 times. The mode has now shifted up by one. E.g. Mode 2 has changed to Mode 3. 4.4 Light levels of light intensity values 0 Level 1 Level 2 Level 3 Level 4 Level Not Operational 15kLUX 30kLUX 45kLUX 60kLUX To Change light level setting: Press the SUN key repeatedly until the desired light level flashes. 4.5 Light intensity detection Press the SUN and P2 buttons for once second Hold the sensor toward the light Response The unit will indicate light level 4.6 Low battery notification When the battery needs changing, the currently selected light level LED will blink every 2 minutes 4.7 UP button The up button can be used to manually overide the sensor and tell the shade to go up. ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 7 5 PROGRAMMING IMPORTANT Please refer to the relevant documentation of your motor model for instructions on adjusting motor settings. 5.1 Protocol selection This device can be configured to operate Acmeda line EL motors. (The default mode is ARC protocol). To toggle between ARC & EL modes follow the following steps. HOLD P2 whilst inserting battery To check which mode the sensor is currently in, press the UP or P2 button briefly. Acmeda EL Protocol: The current LED will blink slowly 4 times to indicate that the old protocol is currently set. ARC Protocol: The current LED will blink fast 8 times to indicate that the new (ARC) protocol is currently set. 8 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA 6 ADDING OR REMOVING SENSOR & CREATING GROUP CONTROL 6.1 Using Motor P1 Button Hold P1 button on motor head. Hold P2 on sensor to add or remove. Motor Response Motor Response 6.2 Using a pre-existing Controller Press P2 on existing controller. Press P2 on existing controller. Press P2 on new sensor. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor. ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 9 7 TROUBLESHOOTING Problem Cause Remedy Sensor battery is discharged Replace battery (Ref. Section 3.2) Battery is inserted incorrectly Check battery polarity
(Ref. Section 3.2) Radio interference / Shielding Ensure remote is positioned away from metal objects and that aerial on motor or reciever is kept straight and away from metal. Motor is not responding Sensor distance is too far from motor Move sensor to a closer position Power failure Incorrect wiring Check power supply to motor is connected and active Check wiring is connected correctly
(refer to motor installation instructions) 10 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA 8 NOTES ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 11 Western Australia Branch Unit 1, 41 Mulgul Road, Malaga WA 6090 T +61 8 9248 5571 | F +61 8 9248 5572 Queensland Branch Unit 2/62 Borthwick Avenue, Murarrie QLD 4172 ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 | F +61 3 9355 0110 ROLLEASE ACMEDA USA 200 Harvard Avenue Stamford, CT 06902 6320 T +1 203 964 1573 | F +1 203 964 0513 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan
(Lombardia) Italy T +39 02 8982 7317 | F +39 02 8982 7317 info@rolleaseacmeda.com rolleaseacmeda.com 12 | Automate Programming Instructions | Interior Sun Sensor