MT02-0101-069007 1. ASSEMBLY 3. PRODUCT RANGE (cont.) P1 LOCATIONS Please refer to separate Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used. 2. BATTERY MANAGEMENT Automate Motor Programming Guide For battery motors;
Prevent discharging the battery completely for extended periods, recharge as soon as the battery is discharged CHARGING NOTES Before first use please charge motor for 6-16 hours, using the recommended AC charger During operation, if battery is low, the motor will beep 10 times to prompt the user it needs charging. 3. PRODUCT RANGE The Quick Start Programming Guide is universal for all Automate Motors including:
INSTALLER BEST PRACTICE AND TIPS SLEEP MODE If pre-programmed: before shipping the motor ensure the motor is put into sleep mode so it doesnt activate during transit. 2.1 Motor State Test 2 P1 BUTTON FUNCTIONS Press Short Press then Release
(<2 sec) Feedback Feedback If limit is NOT set None No Action None No Action If limits are set Operational control of motor, run to P1 limit. Stop if running Motor runs None Operational control of motor after pairing and limit setting is completed first time If motor is in Sleep Mode &
limits are set
(Refer to Sec.10) Wake and control Motor wakes and runs in a direction Motor is restored from None Sleep mode and RF control is active CAUTION 0.6 Cord Lift LOCK REMOTE P1 Press Condition Function Achieved P1 BUTTON FUNCTIONS 3 Prevent users accidently changing the limit;
Short ensure the remote is locked as your last step of programming. 3.1 Motor state test If limit is NOT set Press then If limits are set None No Action Visual Feedback Audible Feedback P1 None Internal Tubular Operational control limit. Stop if running of motor, run to Motor runs None Function Described Activate Pairing Mode No Action Approx. Operational control of motor after pairing Motor Response P1 and limit setting is completed first time RELEASE P1 0.8 Cord Lift ZONE / GROUPS This table describes the function of a short P1 button press/release (<2 seconds) depending on current motor configuration. If motor is in
(<2 sec) Motor Motor is restored from Approx. Sleep Mode Release Sleep Mode &
limits are set Ask the customer the day before to think how shades will be P1 Press Function Achieved
(Refer to Sec.10) zoned on the remote. This may save an extra call out. Condition Wake and control Visual Feedback wakes and runs in a Audible direction Feedback None Sleep mode and RF Function Described control is active Motor Response This table describes the function of a short P1 button press/release(<2 seconds) depending on current motor configuration. 3.2 Motor Configuration Options The P1 Button is utilized to administer motor configuration as described below and beginning in Section 4. 0.8 Cord Lift Hold P1 P1 SETTLE FABRIC set If limit is NOT 2.2 Motor Configuration Options None No Action None No Action The P1 Button is utilized to administer motor configuration as described below and beginning in Section 4. 0.6 Cord Lift Approx. Operational control Activate Pairing Run the fabric up and down several times to ensure fabric of motor, run to limit. has settled to some extent and re adjust the limits if needed. Short Press Approx. If limits are set Stop if running Mode Motor runs Hold P1 None P1 RELEASE P1 Reverse Direction Tilt Motor Curtain Tilt Motor CHARGE 100%
If motor is in Sleep Mode &
limits are set Motor Response RELEASE P1 Wake and control Sleep Mode Motor wakes and runs in a direction For battery motors ensure the motor is fully charged as per instructions. Approx. Note: Curtain motor does not Jog but instead LED flashes. DC motor does not beep. Use a spare remote to individually program each shade. Activate Pairing Mode Then use that remote to group rooms as per the users needs. If you go back and service the installation later then, that same remote can be used to check the individual shades. Approx. Motor Response Reset To Factory Settings Approx. Motor Response Motor Response RELEASE P1 Reverse Direction Approx. Hold P1 Motor Response RELEASE P1 INSTALLERS REMOTE The P1 Button is utilized to administer motor configuration as described below and beginning in Section Programming LED Curtain 7 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA None Operational control of motor after pairing GREEN LED and limit setting is completed first time Motor is restored from Sleep Mode and RF control is active Non-Functional Connectors For Future Use P1 SAFETY Motor Response RELEASE P1 Reset To Factory Settings WARNING: Important safety instructions to be read before installation and use. Approx. Motor Response Incorrect installation or use can lead to serious injury and will void manufacturers liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Do not expose to water,moisture, humid and damp environments or extreme temperatures. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, should not be allowed to use this product. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. Follow installation instructions. For use with motorized shading devices. Keep away from children. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep clear when in operation. Replace battery with correctly specified type. Internal Tubular Large Tubular DISPOSAL AND RECYCLING Do not dispose of in general waste. Sleep Mode Approx. Large Tubular 6 | Automate Programming Instructions | ARC Drapery Motor ROLLEASE ACMEDA INSTALLER QUICK START PROGRAMMING STEP 3 CHECK DIRECTION This setup wizard should be used for new installation or factory reset motors only. Individual steps may not work if you haven't followed the wizard from the beginning. Reverse motor direction from P1 button only when motor does not have any limits. NOTE Approx. Motor Response Reverse Direction Motor Response STEP 1 ON REMOTE STEP 2 PAIRING REMOTE WITH MOTOR OR Reset To Factory Settings STEP 5 SET UPPER LIMIT STEP 6 Approx. SET BOTTOM LIMIT STEP 7 SAVE YOUR LIMIT 2 SECS
* Internal Tubular pictured. Refer to P1 Locations for specific devices P1 Press the P1 button on the motor for 2 Seconds until the motor responds The motor will respond with 1x Jog & 1x Beep Within 4 seconds hold the stop button on the remote until the motor responds as below:
Press up or down to check the motor direction. If correct skip to step 5. STEP 4 CHANGE DIRECTION If the shade direction needs to be reversed;
press and hold the up & down arrow together for 2 seconds until the motor Jogs. MOTOR RESPONSE Motor Response 2 SECS 2 SECS 6 SECS 7 | Automate Programming Instructions | AC Tubular Motors ROLLEASE ACMEDA Move shade to desired top limit by pressing the up arrow repeatedly. Then press and hold up & stop together 2 seconds to save limit. Move shade to desired bottom limit by pressing the down arrow repeatedly. Then press and hold down & stop together for 2 seconds to save limit. Repeat steps 1-6 for all motors. Once complete Push the switch up to lock the remote, the L will breifly appear on the screen. OR Press or buttons to select the channel that needs to be programmed MOTOR RESPONSE 2 SECS 2 SECS JOG x2 BEEP x3 JOG x1 BEEP x1 JOG x2 BEEP x3 JOG x2 BEEP x3 L E S N O P S E R R O T O M E S N O P S E R R O T O M Reversing motor direction using this method is only possible during initial set-up. Tap the arrow several times or hold down if needed; press arrow to stop. Tap the arrow several times or hold down if needed; press arrow to stop. This device complies with Part 15 of the FCC Rules /
Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : 1. Lappareil ne doit pas produire de brouillage; 2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FACTORY RESET MOTOR RESET PROCEDURE To reset all settings in the motor press and hold the P1 Button for 14 seconds, you should see 4 independent jogs followed by 4x Beeps at the end. 14 SECS P1
* Internal Tubular pictured above. Refer to P1 Locations for specific devices MOTOR RESPONSE 2 SECS 6 SECS 10 SECS 14 SECS BEEP x4