SAFETY FCC & ISED STATEMENT ASSEMBLY INSTALLER BEST PRACTICE AND TIPS BUTTON OVERVIEW REPLACE BATTERY WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturers liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Do not expose to water, moisture, humid and damp environments or extreme temperatures. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, should not be allowed to use this product. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. Follow installation instructions. For use with motorized shading devices. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep clear when in operation. Replace battery with correctly specified type. Do not ingest battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Do not dispose of in general waste. FCC ID: 2AGGZ003B9ACA50 IC: 21769-003B9ACA50 For EU Market Operation Temperature Range: -10C to +50C For UK Market Ratings: 3VDC, 15mA For EU Market This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This setup wizard should be used for new installation or factory reset motors only. Individual steps may not work if you havent followed the setup from the beginning. For AU Market Please refer to separate Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used. BATTERY MANAGEMENT For battery motors;
Prevent discharging the battery completely for extended periods, recharge as soon as the battery is discharged. CHARGING NOTES Charge your motor for 6-8hours, depending on the motor model, as per motor instructions. During operation, if battery is low, the motor will beep 10 times to prompt the user it needs charging. PRODUCT RANGE & P1 LOCATIONS The Quick Start Programming Guide is universal for all Automate Motors including:
SLEEP MODE If pre-programmed: before shipping the motor ensure the motor is put into sleep mode so it doesnt activate during transit. LOCK REMOTE Prevent users accidentally changing the limit; ensure the remote is locked as your last step of programming. ZONE/GROUPS Ask the customer the day before to think how shades will be zoned on the remote. This may save an extra call out. SETTLE FABRIC Run the fabric up and down several times to ensure fabric has settled to some extent and re adjust the limits if needed. CHARGE 100%
For battery motors ensure the motor is fully charged as per instructions. INSTALLERS REMOTE Use a spare remote to individually program each shade. Then use that remote to group rooms as per the users needs. If you go back and service the installation later then, that same remote can be used to check the individual shades. P1 P1 P1 WALL MOUNTING Internal Tubular Large Tubular 0.6 Cord Lift P1 P1 Hold P1 0.8 Cord Lift Curtain Tilt Motor Note: Curtain motor does not Jog but instead LED flashes Use supplied fasteners and anchors to attach the base to wall. LED UP STOP DOWN SETTING (P2) LOCK Push ONE Programming Guide MT02-0101-xxx010_v1.0_07062023 ON REMOTE CHECK DIRECTION SET TOP LIMIT SET BOTTOM LIMIT SAVE YOUR LIMIT STEP 3. STEP 5. STEP 6. STEP 7. Press up or down to check the motor direction. If correct skip to step 5. 5 SECS 5 SECS STEP 1. Use a tool (such as a SIM card pin, mini screwdriver, etc.) to push the battery cover release button and simultaneously slide the battery cover in the direction shown. STEP 2. Install CR2450 Battery with positive (+) side facing up. BATTERY ISOLATION TAB Note: On startup, remove battery isolation tab. 3V (CR2450) STEP 3. Slide up to lock the battery door MOTOR RESET PROCEDURE FACTORY RESET To reset all settings in the motor press and hold the P1 Button for 14 seconds, you should see 4 independent jogs followed by 4x Beeps at the end.
* Internal Tubular Motor pictured. Refer to P1 Locations for specific devices. Press the P1 button on the motor for 2 Seconds until the motor responds as below. Condition P1 Press BEEP x3 Short Press If limits are set If limit is NOT set P1 2 SECS JOG x4 then Within 4 seconds hold the stop button on the remote for 3 seconds. The motor will respond with Jog and Beep. OR CHANGE DIRECTION STEP 4. If the shade direction needs to be reversed; press and hold the UP & DOWN arrow together for 5 seconds until the motor jogs. 5 SECS JOG x1 BEEP x1 Reversing motor direction using this method is only possible during initial set-up. Move shade to desired top limit by pressing the up arrow repeatedly. Then press and hold up & stop together for 5 sec to save limit. Move shade to desired bottom limit by pressing the down arrow repeatedly. Then press and hold down &
stop together for 5 sec to save limit. JOG x4 BEEP x3 JOG x4 BEEP x3 SOLID LED
(LOCKED) Tap the arrow several times or hold down if needed;
press arrow to stop. Tap the arrow several times or hold down if needed;
press arrow to stop. 6 SECS P1 14 SECS
(Internal Tubular pictured above. Refer to P1 Locations for specific devices.) Repeat steps 1-6 for all motors before locking the remote. Once complete Press and hold the Lock button for 6 seconds while looking at the LED, and hold until solid. JOG x1 JOG x1 JOG x1 JOG x1 14 SECS BEEP x4 INSTALLERINSTALLERSTEP 1.STEP 2.A division of Rollease AcmedaSECS2SECS6SECS10 CONTROLLING A SHADE CONTROL SHADE UP CONTROL SHADE DOWN STOPPING THE SHADE Press the STOP button to stop shade at any point. DISABLE LIMIT SETTING
- LOCK BUTTON Note: Ensure all shade programming for all motors is completed before locking the remote. This mode is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits. LOCK REMOTE Pressing the lock button for 6 second will Lock the remote and LED will show solid. UNLOCK REMOTE Pressing the lock button for 6 second will Unlock the remote and LED will show flashing. SOLID LED
(LOCKED) FLASHING LED
(UNLOCKED) 6 SECS 6 SECS SET A FAVORITE POSITION Move shade to desired position by pressing UP or DOWN on the remote. Press P2 on remote. Press STOP on remote. Press STOP on remote again. Press P2 on remote. Press STOP on remote. Press STOP on remote. DELETE FAVORITE POSITION OR JOG x1 BEEP x1 JOG x1 BEEP x1 JOG x2 BEEP x3 JOG x1 BEEP x1 JOG x1 BEEP x1 JOG x1 BEEP x1
(First Time)
(Second Time) USER GUIDEUSER GUIDE