SAFETY FCC & ISED STATEMENT 1. ASSEMBLY Automate Motor Programming Guide WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturer's liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Do not expose to water, moisture, humid and damp environments or extreme temperatures. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, should not be allowed to use this product. instruction manual will void warranty. Installation and programming to be performed Follow installation instructions. For use with motorized shading devices. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep clear when in operation. WARNING: Do not ingest battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Operation Temp Range: -10C to +50C Ratings: 3VDC, 15mA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Caution:
not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. INSTALLER BEST PRACTICE AND TIPS PRODUCT RANGE Short Press If limits are set Operational control of motor, run to limit. Stop if running Motor runs P1 LOCATIONS None Operational control of motor after pairing and limit setting is completed first time limits are set direction control is active The P1 Button is utilized to administer motor configuration as described below and beginning in Section Wake and control None Motor wakes and runs in a direction Motor is restored from Sleep Mode and RF control is active If motor is in Sleep Mode &
limits are set Activate Pairing Mode Hold P1 Approx. P1 P1 Hold P1 P1 P1 However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning encouraged to try to correct the interference by one or more of the following measures:
2. BATTERY MANAGEMENT Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a is connected. Consult the dealer or an experienced radio/TV technician for help. For battery motors;
Prevent discharging the battery completely for extended periods, recharge as soon as the battery is discharged CHARGING NOTES Before first use please charge motor for 6 hours, using the recommended AC charger SLEEP MODE SETTLE FABRIC If pre-programmed: before shipping the motor ensure the motor is put into sleep mode so it doesnt activate during transit. Run the fabric up and down several times to ensure fabric has settled to some extent and re adjust the limits if needed Internal Tubular LOCK REMOTE CHARGE 100%
Prevent users accidently changing the limit; ensure the remote is locked as your last step of programming. For battery motors ensure the motor is fully charged as per instructions. ZONE / GROUPS INSTALLERS REMOTE During operation, if battery is low, the motor will beep 10 times to prompt the user it needs charging. Ask the customer the day before to think how shades will be zoned on the remote. This may save an extra call out Use a spare remote to individually program each shade. Then use that remote to group rooms as per the users needs. If you go back and service the installation later then, that same remote can be used to check the individual shades. DISPOSAL AND RECYCLING Do not dispose of in general waste. Activate Pairing Mode Motor Response Approx. Motor Response Sleep Mode Sleep Mode Approx. Large Tubular Motor Response Approx. Motor Response Internal Tubular Large Tubular Reverse Direction Motor Response Reverse Direction Approx. Approx. Motor Response P1 P1 NOTE Reverse motor direction from P1 button only when motor does not have any limits. 0.6 Cord Lift 0.8 Cord Lift Reset To Factory Settings Motor Response 0.8 Cord Lift 0.6 Cord Lift Reset To Factory Settings Approx. Motor Response Approx. P1 7 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA 7 | Automate Programming Instructions | AC Tubular Motors ROLLEASE ACMEDA Curtain Tilt Motor Curtain Note: Curtain motor does not Jog but instead LED flashes P1 Tilt Motor STEP 1 ON REMOTE STEP 2 ON REMOTE STEP 3 CHECK DIRECTION STEP 4 CHANGE DIRECTION STEP 5 SET UPPER LIMIT STEP 6 SET BOTTOM LIMIT STEP 7 SAVE YOUR LIMIT
. 2 SECS 15 5 SECS 5 SECS 5 SECS 6 SECS FACTORY RESET MOTOR RESET PROCEDURE To reset all settings in the motor press and hold the P1 Button for 14 seconds, you should see 4 independent jogs followed by 4x Beeps at the end.
* Internal Tubular pictured above. Refer to P1 Locations for specific devices Press the P1 button on the motor for 2 Seconds until the motor responds as below E S N O P S E R R O T O M JOG x2 BEEP x1 OR If the shade direction needs to be reversed; press and hold the up &
down arrow together for 5 seconds until the motor Jogs MOTOR RESPONSE JOG x1 Within 4 seconds hold the stop button on the remote for 3 seconds. The motor will respond. Press up or down to check the motor direction. If correct skip to step 5 Reversing motor direction using this method is only possible during initial set-up. Move shade to desired top limit by pressing the up arrow repeatedly. Then press and hold up & stop together for 5 sec to save limit. Move shade to desired bottom limit by pressing the down arrow repeatedly. Then press
& hold down & stop together for 5 sec to save limit. E S N O P S E R R O T O M JOG x2 BEEP x3 E S N O P S E R R O T O M JOG x2 BEEP x3 Tap the arrow several times or hold down if needed; press arrow to stop Tap the arrow several times or hold down if needed; press arrow to stop Repeat steps 1-6 for all motors. Once complete Press and hold the Lock button for 6 seconds while looking at the screen L will appear on the screen when locked 14 SECS
* Internal Tubular pictured above. Refer to P1 Locations for specific devices MOTOR RESPONSE 2 SECS 6 SECS 10 SECS 14 SECS BEEP x4 OR Press + or - buttons to select the channel that needs to be programmed i i g n n n g e b e h t m o r f d r a z i w e h t d e w o l l o f t
n e v a h u o y f i k r o w t o n y a m s p e t s l a u d i v i d n I
. y l n o s r o t o m t e s e r y r o t c a f r o n o i t a l l a t s n i w e n r o f d e s u e b d l u o h s d r a z i w p u t e s i s h T R E L L A T S N I I G N M M A R G O R P T R A T S K C U Q I SELECTING A CHANNEL Note: If no button is pressed within 4 seconds, the channel selection will automatically be confirmed LEVELING UP LEVELING DOWN STEP 1 CHANNEL UP CHANNEL DOWN UP DOWN STOP SETTING (P2) LOCK BUTTON OVERVIEW WALL MOUNTING Use supplied fasteners and anchors to attach the base to wall. REPLACE BATTERY Remove Screw Cover Replace cover by pressing snap latches into place. Remove cover from remote press gently in and down to disengage cover. Remote Battery Install battery with positive (+) side facing up
Insert and fasten screw IMPORTANT Battery FOR CHILD SAFETY, SCREW MUST BE USED AT ALL TIMES TO SECURE BATTERY COVER IN PLACE. Battery I E D U G R E S U I E D U G T R A T S K C U Q I OR Press the + or - buttons to select the desired channel 15 STEP 2 READY FOR CONTROL Now while the channel is active follow the control instructions. CONTROLLING A SHADE CONTROL SHADE UP OR DOWN STOPPING THE SHADE 15 15 OR While the channel is displayed press up or down to move shade accordingly LEVELLING CONTROL While looking at the LCD use the up and down buttons on the side of the remote for precision levelling control. When the desired level is reached release finger and the shade will move to that position Press the stop button to stop shade at any point GROUP CONTROL Channel "0" is pre-set to control ALL shades paired to your Muli-channel remote. DISABLE LIMIT SETTING This mode is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits. To switch modes hold right LOCK button for 6 seconds Pressing the lock button for 6 second will toggle between locked and unlocked The Screen will show L or U. For 15 CH For 1 CH SET A FAVORITE POSITION Move shade to desired position by pressing UP or DOWN on the remote. OR 0 LCD displays L when locked LCD displays U when unlocked LED solid on when locked LED blinking when unlocked Press P2 on controller Press STOP on controller Press STOP on controller MOTOR RESPONSE MOTOR RESPONSE MOTOR RESPONSE JOG x1 BEEP x1 JOG x1 BEEP x1 JOG x2 BEEP x3 HIDE UNUSED CHANNELS Your multi channel remote can be configured to have anywhere between 1 or 15 visible channels. Inactive channels will not be visible when scrolling through the CH selection. CREATE CUSTOM GROUPS It is possible to copy one channel to another channel to create custom groups STEP 1. EXISTING REMOTE Select the channel you want to transfer Hold CHANNEL UP and CHANNEL DOWN for 5 seconds until 15 is displayed 15 OR 2 SECS 5 Select + or - and scroll through all channels that you want to hide Press and hold stop for 2 seconds confirm MOTOR RESPONSE MOTOR RESPONSE JOG x1 BEEP x1 JOG x1 BEEP x1 Press P2 Button on existing remote. Press P2 Button again on existing remote. i n h t i w d e t e l p m o c e b o t p e t s t x e N 1 STEP 2. p e t S f o s d n o c e s 4 1 NEW REMOTE Select the channel you want to transfer too B MOTOR RESPONSE JOG x2 BEEP x3 Press P2 Button on new remote. A D V A N C E D P R O G R A M M N G I U S E R G U D E I