FCC ID: 2AGGZ003B9ACA49 VT Tilt Motor

AUTOMATE CORE AND TILT MOTOR INSTRUCTIONS ELECTRONIC LIMIT SELECTABLE SPEED 433 MHZ BI-DIRECTIONAL FAVORITE POSITION SOLAR OPTION LEVEL CONTROL USE THIS DOCUMENT WITH THE FOLLOWING MOTORS:

PART NUMBER DESCRIPTION MT01-4001-xxx002 Passthrough Tilt Motor Kit MT01-4001-069003 AUTOMATE | VT TILT [12V/0.6Nm/11rpm]

AUTOMATE_TILT_PRGM_OCT_2023 SAFETY INSTRUCTIONS WARNING: Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturers liability and warranty. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. Ensure correct crown and drive adaptors are used for the intended system. Do not cut the antenna. For use within tubular blinds. Do not allow children to play with this device. Keep antenna straight and clear from metal objects Do not expose to moisture or extreme temperatures. CAUTION Motor is to be installed in horizontal application only. If cable or power connector is damaged do not use. Use only Rollease Acmeda hardware. Do not drill into motor body. The routing of cable through walls shall be protected by isolating bushes or grommets. Ensure power cable and aerial is clear and protected from moving parts. Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation. Ensure torque and operating time is compatible with end application. Do not expose the motor to water or install in humid or damp environments. Important safety instructions to be read prior to operation. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product. Keep remote controls away from children. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep motor away from acid and alkali. Do not force the motor drive. Keep clear when in operation. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 2 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician to help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dISED applicables aux appareils radio exemps de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installes doivent tre situes de facon ce que la population ne puisse y tre expose une distance de moin de 20 cm. Installer les antennes de facon ce que le personnel ne puisse approcher 20 cm ou moins de la position centrale de l antenne. La FCC des ltats-unis stipule que cet appareil doit tre en tout temps loign dau moins 20 cm des personnes pendant son functionnement. ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 3 CONTENTS 1 2 3 CORE TILT MOTOR ASSEMBLY CORE TILT MOTOR WAND OPERATION TILT MOTOR ASSEMBLY 4 WIRING 4.1 Power Options 5 P1 BUTTON FUNCTIONS 5.1 Motor state test 5.2 Motor configuration options 6 INITIAL SET UP 6.1 Pair motor with controller 6.2 Check motor direction 6.3 Set Limits 7 ADJUSTING LIMITS 7.1 Adjust upper limit 7.2 Adjust lower limit 8 CONTROLLERS AND CHANNELS 8.1 Using P2 Button on existing controller to add a new controller or channel 8.2 Using a pre-existing controller to add or delete a controller or channel 9 FAVORITE POSITIONING 9.1 Set a favorite position 9.2 Send shade to favorite position 9.3 Delete favorite position 10 TILT & ROLLER MODE 10.1 Toggle motor to Tilt Mode 10.2 Toggle Motor to Roller Mode 11 ADJUSTING SPEED 11.1 Increase Motor Speed 11.2 Decrease Motor Speed 12 SLEEP MODE 13 TROUBLE SHOOTING NOTES 5 6 7 8 8 9 9 9 10 10 10 11 12 12 12 13 13 13 14 14 14 14 15 15 15 16 16 16 17 18 19 4 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA 1 CORE TILT MOTOR ASSEMBLY Assemble correct configuration as required Disassemble existing venetian manual control assembly Insert motor assembly into existing venetian head rail assembly Re-insert tilt rod through the motor assembly & spools Attach switch control cover Battery Charging ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 5 2 CORE TILT MOTOR WAND OPERATION Optional Control Wand 6 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA 3 TILT MOTOR ASSEMBLY Assemble correct configuration as required Insert motor assembly into venetian head rail assembly Ensure tilt rod is engaged with the motor Minimum tilt rod insertion with motor is 1/2 Maximum tilt rod insertion with motor is 3/4 Battery Charging ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 7 4 WIRING 4.1 Power Options Automate DC TILT Motor is powered from a 12V DC power source. AA Battery wands, re-chargeable battery packs with a variety of quick connect extension cords. For centralized installations, power supply range can be extended with 18/2 wire (not available through Rollease Acmeda). During operation, if voltage drops to less than 10V, the motor will beep 10 times to indicate a power supply issue. Motor will stop running when the voltage is lower than 7V and it will resume again when the voltage is greater than 7.5V. NOTE:

Passthrough Tilt Motor MT01-4001-xxx002 comes supplied with a rechargeable battery pack. Power Supply Compatible Motors MTBWAND18-25 | Battery Tube for 18/25mm DCRF (no Battery) Mtrs

(inc Mt clips) MTDCPS-18-25 | Power Supply for 18/25-CL/Tilt DCRF (no Bttry) Mtr MT01-4001-069003 MTBPCKR-28 | Rechargeable Wand MT03-0301-069011 | USB Wall Charger - 5V, 2A (AU ONLY) MT03-0301-069008 | USB Wall Charger - 5V, 2A (US ONLY) MT03-0301-069007 | 4M (13ft) USB Micro Cable MT03-0302-067001 | Solar Panel Gen2 MT01-4001-xxx002 Extension Cables Compatible with MTDC-CBLXT6 DC Battery Motor Cable extender 6 / 155mm MTDC-CBLXT48 DC Battery Motor Cable extender 48 / 1220mm MT01-4001-069003 MTDC-CBLXT96 DC Battery Motor Cable extender 96 / 2440mm MT03-0301-069013 | 48/1200mm 5V Cable Extender MT03-0301-069014 | 8/210mm 5V Cable Extender MT01-4001-xxx002 MT03-0301-069 Ensure cable is kept clear of fabric. Ensure antenna is kept straight and away from metal objects. 8 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA 5 P1 BUTTON FUNCTIONS 5.1 Motor state test This table describes the function of a short P1 Button press/release (<2 seconds) depending on current motor configuration. P1 Press Condition Function Achieved Visual Feedback Audible Feedback Function Described If limit is NOT set None No Action None No Action If limits are set Short Press If motor is in Sleep Mode &

limits are set Operational control of motor, run to limit. Stop if running Wake and control Motor Runs None Operational control of motor after pairing and limit setting is completed first time Motor wakes and runs in a direction None Motor is restored from Sleep Mode and RF control is active 5.2 Motor configuration options The P1 Button is utilized to administer motor configurations as described below. Hold P1 button on motor head. Activate Pairing Mode P1 button on motor head. Approx. Sleep Mode Approx. Approx. Reverse Direction Approx. Approx. Approx. 10 Reset To Factory Settings Approx. Approx. Approx. 10 Approx. IMPORTANT ONLY THE PASSTHROUGH MOTOR EMITS A BEEPING NOISE. IGNORE THIS ICON WHEN PROGRAMMING MT01-4001-069003. ALL OTHER PROMPTS ARE THE SAME FOR BOTH MOTORS. ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 9 6 INITIAL SET UP 6.1 Pair motor with controller Select channel on controller. Hold P1 button on motor head. Hold STOP on controller. IMPORTANT Consult user manual for your controller for information on selecting channel. Motor Response*

Motor Response*

Approx. Motor is now in step mode and ready for setting limits 6.2 Check motor direction To check travel direction of shade, press UP or DOWN on controller. To reverse shade direction, hold both UP and DOWN. Until the motor responds. OR Quick Press = Step Long Press = Continuous Travel Motor Response*

Approx. IMPORTANT Damage to shade may occur when operating motor prior to setting limits. Attention should be given. IMPORTANT Reversing motor direction using this method is only possible during initial set-up NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 10 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA 6.3 Set Limits IMPORTANT Cycle shade up and down prior to setting limits to settle fabric Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. To save upper limit, hold UP and STOP. OR Motor Response*

Approx. 5 SEC S Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. To save lower limit, hold DOWN and STOP. OR Motor Response*

Approx. 5 SEC S IMPORTANT After setting limits, motor will automatically exit from initial set-up mode. ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 11 NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 7 ADJUSTING LIMITS 7.1 Adjust upper limit Hold UP and STOP on controller. Move shade to the desired highest position by pressing the UP or DOWN button. To save upper limit, hold UP and STOP. OR Motor Response*

Approx. 5 SEC S Motor Response*

Approx. 5 SEC S 7.2 Adjust lower limit Hold DOWN and STOP on controller. Move shade to the desired lowest position by pressing the UP or DOWN button. To save lower limit, hold DOWN and STOP. OR Motor Response*

Approx. 5 SEC S Motor Response*

Approx. 5 SEC S IMPORTANT The bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is raised. 12 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 8 CONTROLLERS AND CHANNELS 8.1 Using P2 Button on existing controller to add a new controller or channel A = Existing controller or channel (to keep) B = Controller or channel to add or remove Press P2 on controller A. Press P2 on controller A. Press STOP on an new controller to add it. Motor Response*

Motor Response*

Motor Response*

IMPORTANT Consult user manual for your controller or sensor 8.2 Using a pre-existing controller to add or delete a controller or channel A = Existing controller or channel (to keep) B = Controller or channel to add or remove Press P2 on controller A. Press P2 on controller A. Press P2 on the controller B to remove it. Motor Response*

Motor Response*

Motor Response*

IMPORTANT Consult user manual for your controller or sensor ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 13 NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 9 FAVORITE POSITIONING 9.1 Set a favorite position Move shade to the desired position by pressing the UP or DOWN button on the controller. Press P2 on controller. Press STOP on controller. Press STOP on controller. OR Motor Response*

Motor Response*

Motor Response*

9.2 Send shade to favorite position Approx. 9.3 Delete favorite position Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response*

Motor Response*

Motor Response*

14 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 10 TILT & ROLLER MODE 10.1 Toggle motor to Tilt Mode Default motor mode is Roller after initial Limits have been set, use following steps to change to Roller Mode. Hold UP & DOWN on controller. Press STOP on controller. Motor Response*

Motor Response*

Approx. 5 SEC S 10.2 Toggle Motor to Roller Mode If motor is in Tilt Mode, use following steps to change to Roller Mode. Hold UP & DOWN on controller. Press STOP on controller. Motor Response*

Motor Response*

Approx. 5 SEC S ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 15 NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 11 ADJUSTING SPEED 11.1 Increase Motor Speed NOTE: Repeating this step when at the fastest speed ENTERS Soft Stop Mode in MT01-4001-069001. Press P2 Press UP Press UP Motor Response*

Motor Response*

Motor Response*

11.2 Decrease Motor Speed NOTE: Repeating this step when at the slowest speed EXITS Soft Stop Mode in MT01-4001-069001. Press P2 Press DOWN Press DOWN Motor Response*

Motor Response*

Motor Response*

16 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 12 SLEEP MODE 9 SLEEP MODE If multiple motors are grouped on a single channel, Sleep Mode may be used to put all but 1 motor to sleep, allowing programming of just the one motor that remains Awake. See page 6 for detailed P1 functions. Enter Sleep Mode Exit Sleep Mode: Method 1 Exit Sleep Mode: Method 2 Sleep mode is utilized to prevent a motor from incorrect configuration during other motor setup. Hold P1 button on the motor head Exit sleep mode once the shade is ready. Remove power and then re-power the motor. Press and release P1 button on the motor head Motor Response*

Motor Response*

Approx. NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 17 G 13 TROUBLE SHOOTING rolleaseacmeda.com Problem Cause Remedy Motor is not responding Battery in motor is depleted Recharge with a compatible charger Insufficient charging from solar PV panel Check connection and orientation of PV panel Controller battery is discharged Replace battery Battery is inserted incorrectly into controller Radio interference/shielding Check battery polarity Ensure transmitter is positioned away from metal objects and the aerial on motor or receiver is kept straight and away from metal Receiver distance is too far from transmitter Move transmitter to a closer position Charging failure Motor beeps x10 when in use Battery voltage is low Cannot program a single motor

(multiple motors respond) Multiple motors are paired to the same channel Check power supply to motor is connected and active Recharge with a compatible charger Always reserve an individual channel for programming functions. Use Sleep Mode to program individual motors. 18 | Automate Programming Instructions | Tilt Motors ROLLEASE ACMEDA NOTES ROLLEASE ACMEDA Automate Programming Instructions | Tilt Motors | 19 info@rolleaseacmeda.com rolleaseacmeda.com ROLLEASE ACMEDA USA 200 Harvard Avenue Stamford, CT 06902 6320 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan

(Lombardia) Italy ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +1 203 964 1573 | F +1 203 964 0513 T +39 02 8982 7317 | F +39 02 8982 7317 T +61 3 9355 0100 | F +61 3 9355 0110 Queensland Branch Unit 2/62 Borthwick Avenue, Murarrie QLD 4172 20 | Automate Programming Instructions | Tilt Motors

AUTOMATE | VT TILT 12V/0.6Nm/lirpm]

MTO1-4001-069003 FCC ID: 2AGGZOO03B9ACA49 IC: 21769-003B9ACA49 RECOGNIZED COMPONENT 12V DC MADE IN PRC 0.5A 6W IP20 CLA | 12min | 0.13kg This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-01-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AGGZ003B9ACA49 Rollease Acmeda Inc. certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information:

FRN: 0025043381 Name: Rollease Acmeda Inc Address: 7th Floor / 750 East Main Street,Stamford, CT 06902, USA Contact Person: Jonny.Matuichuk Tel.: 2034906191 Email: jonny.matuichuk@rolleaseacmeda.com Sincerely, Jonny.Matuichuk

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-01-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AGGZ003B9ACA49 Rollease Acmeda Inc certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Applicant signature:

Applicant printed name: Jonny.Matuichuk Rev 1/26/2023

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-01-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AGGZ003B9ACA49 Rollease Acmeda Inc certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Applicant signature:

Applicant printed name: Jonny.Matuichuk Rev 1/26/2023

Date: 01/06/2023 Confidentiality Request FCC ID: 2AGGZ003B9ACA49 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, Rollease Acmeda Inc (7th Floor / 750 East Main Street, Stamford, CT 06902, USA) hereby requests permanent confidential treatment of information accompanying this application as outlined below:

Schematics, Block Diagrams, Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Company Officer:

Jonny.Matuichuk Telephone Number:

Email:

jonny.matuichuk@rolleaseacmeda.com

Date: 06-01-2023 SUBJECT: FCC Application for FCC ID: 2AGGZ003B9ACA49 Dear Sir or Madam, We, Rollease Acmeda Inc (7th Floor / 750 East Main Street, Stamford, CT 06902, USA), hereby authorize Yu Anlu from TV SD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151 Heng Tong Road Shanghai 201108 P.R. China to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expires on 12-01-2023. Sincerely, Company Officer:

Jonny.Matuichuk Telephone Number:

Email:

jonny.matuichuk@rolleaseacmeda.com

RolleaseAcmeda Inc Date:2023-05-29 To: Federal Communications Commission 7435 Oakland Mills Road Columbia MD FCC ID:2AGGZ003B9ACA49 To Whom It May Concern:

This letter is to ascertain that RolleaseAcmeda Inc Product name: VT Tilt Motor, Model: MT01-4001-069003 has been the units used for conducting FCC compliance testing, the SDoC part will be tested by FCC recognized test lab. If you have any question or concerns, please contact us. Sincerely, Signature Company name:RolleaseAcmeda Inc Address:7th Floor / 750 East Main Street,Stamford, CT 06902, USA E-mail:jonny.matuichuk@rolleaseacmeda.com Tel:2034906191 Printed Name:Jonny.Matuichuk