FCC ID: 2AHY2US4G-65 Complete 5 Bands Cellphone Signal Booster

arenes Fe

(c learCast Complete 5 Bands Cellphone Signal Booster Installation Guide Table of Contents Package Content ...............ccccccccccesccceceesceeeceeeeceeceeeeeeseeeceesaaaees 1 Installation Notice & Attenuations .............0..ccceeccceeeeeseeeeeeeeees 2~4 Step A: Outdoor Antenna Installation ................ ce eeeeee seen 5~6 Step B: Indoor Antenna Fastening ...............cccccceceeceeeeeee eee ees 7~8 Step C: LED Light status Indication................ cc ceeccceeee eee 9~10

& Reset the Booster Step D: Find Best Reception Level & Bars........................ 11~12 vs. Indoor Service Area / Quality Abnormal LED Light Status & Trouble shooting ................ 13~14 Booster Safeguard Features ..............cccccccccceccccceeeeceeeeeeeeeeeenees 15 Users Safety REMINCELSS 0.0.0.0... ccc cccecccccceesecceceeeceeeeeeeceeseenees 16 Authorized Accessories List , specifications..................... 17~18

& Warranty Package Contents LPA-F78 Outdoor Antenna PA-F45 Indoor Antenna US4G-65 Booster Main Unit 4 pcs 1 high tensile screws CL06-33F1F 1-06 33ft RG-06/U Coaxial Cable 110VAC5V2ADC RH-050200US i Power Adaptor 2 pcs 3/4 high tensile screws CLO6-11F1F 1-06 11ft RG-06/U Extension Coaxial Cable CLO06-17F1F 1-06 17ft RG-06/U Coaxial Cable B1 BRACKET for Outdoor Antenna A2 BRACKET for Outdoor Antenna B2 BRACKET for Indoor Antenna BRACKET for Outdoor Antenna AD-T1F0-06 TNC(M)-F(F) Adaptor ODA Accessories for Outdoor Antenna SCREWS =|

2pcs AD-N1F0-06 2pcs AD-FOF0-06 9 N(M)-F(F) Adaptor F(F)-F(F) Adaptor 4 U Bolt Installation Notice & Attenuations How It Works: Cellphone Signal Booster DIY Kit is a set of easy-to-install electronic product used to improve the poor reception of cellphones at home. It amplifies weak, distant cell tower signals and directs them indoors, greatly improving the quality of indoor cellphone calls and Internet access.

((\) we ik ams TN Tl IS f

[ost aa a Unit Glossary table: Express the terms in a short form in order to simplify the installation guide, improve the ease of reading and enable intuitive understanding of terms.

* Cellphone Signal Booste Booster Tune /Search the Outdoor Antenna orientation for best reception Find Best Reception Rotate/Move the Outdoor/Indoor

. Tune the Outdoor/Indoor Antenna Antenna orientation/location

* Cellphone reception bars Reception bars Power off and then power on the booster Reset booster Installation Prectiauons:

In order to get the best reception, please read the following notes and instructions for STEP A, B, C and D before installation. All key points and notes for the installation can be divided into 3 categories:

e Distance, position and orientation for the installation of outdoor and indoor antennas. e Installation of connectors, adapters, and coaxial cables. e About Tune the outdoor and/or Indoor antenna for best reception and Power on/Reset the booster. During testing or regular use, the LED indicators will stay either red or green when the booster operates normally. Of the 4 LED lights, some may remain red and some may remain green. LED indicators blinking red or green indicate an abnormality. Please refer to Abnormal LED Light Status & Troubleshooting on page 13, 14 and conduct troubleshooting according to the instructions until the booster works properly.

(1.) Holda cellphone and walk outside around the house slowly to find a location with the best reception. Alternatively, install the outdoor antenna toward the direction where a cell tower is known to be installed. This is the most important step in the installation process, as it will determine the reception quality and service coverage of cellphone calls and internet access when used indoors.

! 2.) Please keep the minimum space 20 ft vertical and/or 40 ft horizontal of the outdoor/indoor antennas clear so that the cellphone signal booster can work properly (see page 6). 3.) + The outdoor antenna should be kept 6 ft away or 5 ft higher than windows.

- The outdoor and indoor antennas should be kept facing away or at an angle 90 to 180 from each other. Avoid placing the outdoor antenna facing the house or positioning the outdoor and indoor antennas in the same direction. 4.) Please maintain a suitable path for all coaxial cables :

- Ina straight line

* Make smooth turns

e No sharp-angle turns Y | |

e Do not coil cables ) CD Tom e Do not cross the coaxial cables or paths connecting the outdoor and indoor antennas. e The coaxial cable connecting the outdoor antenna needs to be kept in a U shape before entering the house so that rainwater will not flow into the house along the cable. e In order to maintain the tidiness of the indoor environment, the coaxial cables connecting the outdoor and indoor antennas can be hidden above the ceiling or along the wall to the main unit. e Check all outdoor and indoor antenna connectors, adapters, coaxial cable connectors, and main unit connectors, and fasten them by hand (without tools). Unfastened or loose connections will not improve the indoor reception.

* ' Do not power up the main unit yet. Wait until the brackets of the outdoor antenna are adequately fastened such that the antenna can still be rotated , and the position / orientation of the indoor antenna should be secured before performing Step D - Find best reception. Then, power up the booster while adjusting the outdoor antenna. Perform Step C - LED light status indication to confirm and adjust the reception results of the installation, or as the basis for Abnormal LED light status &

troubleshooting (page 13 and 14). Whenever performing "Tune the outdoor and/or indoor antenna" steps in installation procedure or after long-term use, the main unit must be reset to ensure LED stay either red or green and that the booster works properly. Step A Installation of outdoor antenna The outdoor antenna can be secured in the following different ways according to the on-site installation. GD Use only securing brackets (must separately purchase the metal rods with a diameter of 1.2 to 1.6 inches used for securing) e Ai BRACKET for Outdoor Antenna

| Note: | The elevation angle of the outdoor antenna is adjusted to be horizontal

(O~10 up tilt) if it is on a plain or in the suburbs and urban areas. Tilt the unit upwards in valleys, and downwards in hilly and highland areas. G Secured on the outer wall with 3D brackets that allow adjustment of elevation and/or azimuth angle. fasten by screwdriver

| Note: | * Secure on wooden/concrete wall: Screw 1 inch high tensile screws, 4PCS Use electrical screwdriver fastening these high tesile screws to the wall.

@ e Please keep the space 20 ft vertical and/or 40 ft minimum horizontal of the indoor antennas clear. e The outdoor antenna should be kept 6 ft away or 5 ft higher than windows. e The outdoor and indoor antennas should be kept facing away or at an angle of 90 to 180 from each other. e Avoid placing the outdoor antenna facing the house or making the outdoor and indoor antennas facing the same direction. e Do not fasten the outdoor antenna after it is installed. Secure it in a manner such that it can still be rotated to find the best orientation for reception. i 40 ft minimum horizontal space 20 ft minimum vertical space LPA-F78 ~

AD-N1FO-06 N(M)-F(F) Adaptor rs (M)-F(F) Adapt 90~180 face away from outdoor antenna orientation Q, AD-N1F0-06 N(M)-F(F) Adaptor ae 33ft RG-O6/U Coaxial Cable all Outdoor Indoor >

AD-T1F0-06 TNC(M)-F(F) Adaptor J< QD <

US4G-65 Booster Main Unit

@ 1+ In order to maintain the tidiness of the indoor environment, the coaxial cables can be hidden above the ceiling or along the wall to the main unit. 2+ Outdoor antenna connectors, adapters, 33 ft coaxial cable connectors connecting to the main unit. Step B Installation and fastening of indoor antenna There are 2 ways to fasten an indoor antenna. Note that the installation position must maintain vertical minimum and/or horizontal spacing and be kept facing away or at an angle of 90 to 180 from the outdoor antenna (see page 3 and 4).

@q Direction-securing bracket: When fastening on an indoor wall, keep module facing away from or at an angle of 90 to 180 from the outdoor antenna. If this cannot be done, use the B2 method to fasten the indoor antenna. wall PA-F45 Indoor Antenna BRACKET 3/4" high tensile for Indoor Antenna screws 2pcs

@ Movable indoor antenna fastening bracket:

Adjust to face away from or at an angle of 90 to 180 from the outdoor antenna. Adhere to a table or cabinet with double sided tape after finding best reception procedure was done. >

(B3) Connects the indoor antenna connector, adapter, the 17 ft coaxial cable, and the main unit. If not long enough, extend with an 11 ft coaxial cable by AD-FOFO-06 adapter. (option) Indoor Antenna PA-F45 AD-N1F0-06

| N(M)-F(F) Adaptor egy (Pp US4G-65 17ft RG-6/U Coaxial Cable Booster Main Unit AD-T1F0-06 TNC(M)-F(F) Adaptor

= > d| sees ] < @ <

33ft RG-6/U \

(Option) Connection of 11ft RG-6/U Extension Coaxial Cable Coaxial Cable \

AD-FOFO-06 F(F)-F(F) Adaptor ee 1. Adjust the position/orientation of the indoor antenna before "Powering up booster. Do not move or rotate the indoor antenna during testing or use. 2. Every time you "Tune the indoor antenna", the main unit must be reset. If the LED indicators on the main unit blink red, the location / orientation of the indoor antenna must be adjusted until each LED indicators stay red or green. 3. The best position to install the indoor antenna is 5 to 7 ft above the ground. 4. In order to maintain the tidiness of the indoor environment, the coaxial cable connecting the main unit to the indoor antenna can be hidden above the ceiling or along the wall. 5. Cellphone are to be used more than 3m away from the indoor antenna. Step C LED Light status Indication & Reset the Booster Each LED of the main unit stays red or green to display the normal operation of the corresponding frequency band and the reception strength. Bands shown in red have weaker reception, and bands in green have stronger reception. Of these 4 LEDs, some may appear red, and some may appear green. Every time the outdoor or indoor antenna is adjusted, or when the booster system is in use, all LEDs on the main unit must stay either red or green. If anyone or more LEDs on the booster blink, the main unit is not working properly. The LEDs should not blink red at any time. If the cell tower is too close to the house, the frequency band will be indicated by a blinking green LED. See page 13 and 14 for the handling procedures when LEDs blink red or green. Indoor reception quality, coverage, and LED light corresponding to reception strength and signal quality are shown below:

Signal level I Range Reception Bars 7 1 TT ut atl il Indoor Reception extremely weak fair good excellent excessive (over) Grade weak reception Indoor Reception i poor | usable fair ; good i excellent corresponding Quality/Coverage deadzone small moderate moderate large band shut down LED Light (Solid) Red Red ; Red Red or Green Green blinking Green Solid Red:

1 - The house is far from the base station, and the reception is weak. 2 - The outdoor antenna is probably not adjusted to the best orientation. Please refer to Step D on pages 11 and 12 to find the orientation for best reception.

| Note: | + In remote areas where the signal is extremely weak, the LED display may still appear solid red even after Step D is taken to adjust the outdoor antenna to the best orientation for best reception. However, there may be minimal coverage of indoor service.

+ Even if the LED indicators stay solid red, the outdoor antenna that aims at the direction of the cell tower after adjustment can provide a greater indoor coverage and better reception quality than those not aligned with the cell tower. Solid Green: The booster is in the best reception configuration. Try to adjust the orientation of the outdoor antenna so that all LED indicators stay green.

[ Note:] If the LED indicators show solid green, but the indoor reception is poor, please refer to page 14 for solutions. Abnormal state:

Anyone or more LED indicators blink red and the main unit has detected that the installation is in an abnormal state. Power is cut off for all frequency bands. If the LED indicators blink green, it means that the cell tower at this frequency band is too close to the house. (Not necessarily the carrier registered by the user. Booster only cuts off amplification of this frequency band, other frequency bands are normal.) Please refer to page 13 and 14, and follow the instructions for various abnormal LED statuses to restore normal operation. Reset the Booster Try to use a 110 VAC power strip with a surge protector to supply power to the AC-DC adapter of the booster. If each power socket has a separate power switch, it will be more convenient to reset the main unit during the STEP D Find Best Reception process. Do not power off/power on (reset) the main unit too quickly. Leave an interval of 3 seconds or more between off and on to protect the AC-DC adapter and the booster main unit. Every time the orientation and/or the location of the outdoor or indoor antenna is adjusted, the booster needs to be reset to make sure that the main unit is working properly. If the LED indicators blink red, the orientation/location of the outdoor and indoor antenna needs to be adjusted until the main unit works properly. Different way to Reset/Power up the Booster. Step D Find Best Reception & Reception Bars vs. Indoor Service Area and Quality Adjusting/finding the best reception orientation of the outdoor antenna is the most important step in installing the cellphone signal booster. It will determine the cellphone indoor reception quality and service coverage of voice call and internet access. Reception Level & Bars vs. Indoor Service Area and Quality :

Signal level :

Range Outdoor Reception Y I | Wl Wl ll Bars/Grade ; ;

extremely weak fair good excellent corresponding weak band shut down Outdoor Reception Level (dBm) -120 -110 -100 -90 2 -89 2 -59 Reference Indoor | dead zone/ cellphone Link with small moderate moderate large Coverage Range very small Cell tower directly Coverage (sq.ft) < 300 800 1500 3000 5000 Indoor Reception - cellphone Link with 7 poor poor fair good excellent Quality Cell tower directly FED.Light: RED RED RED RED/GREEN| GREEN Blinking Green Status (solid) Find Best Reception e It is best to have 2 people working on this at the same time. One person adjusts the orientation of the outdoor antenna, and the other person works indoors to record the reception bars for each orientation of the outdoor antenna. Next, the outdoor antenna is secured at the orientation which provides the most reception bars.

(STEP1] First, rotate the outdoor antenna to about the middle of the adjustable range. The individual (working outdoors) should get behind the back of the antenna, then remove their hands from the antenna surface. The individual working indoors should then power up the main unit and then slowly back away more than 3 ft from the indoor antenna with a cellphone in hand. Once the reception bar signal strength indicator shows 2 to 3, wait for about 30 to 50 seconds to make sure that the reception bars is stable. Remember the position in which the individual is standing. Maintain the same posture as the testing baseline when adjusting various orientations on the outdoor antenna. Then, record the reception bar and turn off power.

(STEP2] Divide the rotation range of the outdoor antenna into 8 - 10 orientations, then follow the steps below:

(Outdoors) Rotate the orientation of the outdoor antenna to the far left (or the far right) The individual gets behind the back of the antenna and removes hands

(Indoors) Power up the main unit Stand on the testing baseline point, maintain posture, and wait for about 30 to 50 seconds (These 3 key point are very important ! ) Record the cellphone bars Power off Repeat: (Outdoors) Adjust the outdoor antenna to the next orientation (Indoors)... 1 + Different holding postures in the same indoor position can change cellphone reception bar (especially in areas with weak reception), which will influence finding the optimal orientation of the outdoor antenna for best neception. 2. During the adjustment of the outdoor antenna, if any single LED blinks red during the main unit reset, the unit must be powered off immediately. Refer to the solutions in the Abnormal LED Light Status & Troubleshooting on page 13, then re-power the main unit. Once all LED indicators show proper function, continue with the Find Best Reception step.

(STEPS) Repeat the above steps until all orientations of the outdoor antenna are adjusted from left to right in sequence, then record the corresponding reception bars. The orientation of the outdoor antenna with the best reception bars represents the optimal direction for reception. Use your cellphone indoors to make calls and walk around to confirm reception.

(STEPS) Start fastening the brackets that secure the outdoor antenna. Wrap the outdoor antenna connector, adapter, and coaxial cable with waterproof tape. The coaxial cable entering the house needs to be kept in a U shape and should be clamped to the wall every 2 to 3 ft along the path.

Abnormal LED Light status & Trouble Shooting Abnormal state:

e LED blinking Red : Increase the vertical and/or horizontal spacing of the outdoor and indoor antenna, or adjust the orientation/position of the outdoor and/or indoor antenna until all LED indicators appear solid red, or green.

| Note: | 1- Before the adjustment procedures to eliminate the LED indicators blinking red, the main unit must be powered off first and then power on (reset). 2 + Whether it is during the installation or regular use, LED indicators blinking Red must be eliminated and then reset the power until they appear solid red, green. e LED blinking Green : The cell tower in this frequency band is very close to the house. When the outdoor antenna receives a strong signal, the main unit will automatically shut off the corresponding frequency band. The cellphone is directly connected to the cell tower, no longer boosted through the cellphone signal booster. The cell tower may not be the carrier to which the user registered, and it may belong to other carriers:

1:-Nearby cell tower belongs to the carrier to which the user is registered:

If the indoor reception is good in other frequency bands or the bands that blink green, continue to use the booster. Ignore the blinking Green LEDs, as there is no need to adjust the orientation of the outdoor antenna. 2 - The nearby cell tower belongs to other carriers and the cell tower of the user registered is far away: It is necessary to set a new outdoor antenna position. Use the house as an obstacle to block outgoing signals from the cell towers of other carriers to receive more cell tower signals from the carrier to which the user is registered. Follow procedures in Step D to find the orientation for the best reception, and then secure the outdoor antenna.

| Note: 1. When eliminating the frequency bands of LEDs blinking Green, the main unit can still be powered. Move the orientation of the outdoor antenna away from the nearby cell tower until the LEDs stay solid green, and then reset the booster to make sure that it works properly. 2. Adjusting the orientation / location of the outdoor antenna may change the reception of other frequency bands. If the reception results of other frequency bands are therefore reduced, the new location of the outdoor antenna must be changed. Follow the procedures of Step D to find the orientation of the outdoor antenna with the best reception. e LEDs appear solid green, but the cellphone reception is not good : The cell towers belonging to other carriers are far from the house, and their signal strength makes the LED of the booster appear solid green. However, the cell tower of the carrier to which the user registered is even further from the house. It is necessary to get a new location for the installation of the outdoor antenna. Use the house as an obstacle to block out side signals from the cell towers of other carriers. Follow procedures in Step D to receive more cell tower signals from the carrier to which the user is registered. LED lights blinking orange (red and green lit together) : If the cellphone gets too close to the indoor antenna, the main unit will blink orange. Keep the cellphone further away from the indoor antenna, and the booster operation should return to normal.

| Note: | It is recommended that cellphone be used at least 3 ft away from the indoor antenna. During calls, it is easy to get disconnected, moreover, reception bars can fluctuate, or internet access may become unstable :

The condition can be improved by adjusting the orientation of the outdoor antenna to aim at one cell tower only. Try to avoid an orientation of the outdoor antenna that points between two cell towers, as this can easily lead to the above mentioned reception bar fluctuations. LED indicators appearing solid red or green without any improvement in reception :

Check all outdoor and indoor antenna connectors, adapters, coaxial cable connectors, and main unit connectors, then make sure that they are secured. Fasten by hand (without tools) if necessary. No LED indicators light up :

Check if the power socket or power strip is properly powered by 110 V AC from the AC-DC adapter included in the Booster kit. If there is a problem with the AC-DC adapter, please contact your dealer for a replacement. Booster Safeguard Features e Anti-oscillation :

The booster detects an oscillated signal and shuts down within 0.3 and 1.0 sec for UL and DL CKT respectively. Operation re-initiates detection after 60 sec for no more than 5 times then shuts down permanently until the users reset the booster. e AGC, power control / power down and noise limitation :

The booster amplifies but does not alter incoming signals from cell towers and cellphones without distortion by automatically controlling the boosters gain and power within a manageable input range. When the incoming signal level exceeds this range, the booster may shut down or power down the UL and / or DL CKT to reduce output noise. This may occur in the following scenarios:

1. Loop oscillation 2. Outdoor antenna is nearby a cell tower 3. Cell phone in use close to indoor antenna 4. UL CKT deactivated within 5 min after a call has ended The booster reduces both gain and/or power for UL and DL CKT. The outdoor antenna reception level enables DL AGC CKT as the variable gain function. Each signal Booster is individually tested and factory-set to comply with FCC and IC guidelines. The signal Booster cannot be set or adjusted by user both software/hardware. Only the factory can program the device. FCC and IC information :

This device complies with class B digital device guidelines pursuant to part 15 of FCC Rules under reasonable protection against harmful interference in residential house installation. Operation is subject to two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may Cause undesired operation. e IC: (The term IC refers to Industry Canada technical specifications.) Class B digital devices meet all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may Cause undesired operation. Users Safety Reminders ___OEEEEEEEEE Ensure the signal booster operating temperature remains between 59 to 113 F (15 to 45 C) in an indoor environment. Do not connect the booster directly to any cell phone/device, as this may damage the cellphone signal booster. AWS Warning: Do not install the outdoor ANT higher than 10 m above ground. For RF safety, Either outdoor or indoor ANT must remain at least 8 inches (20 cm) away from all personnel. Pe Bb Bb Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

e Rotate/move the outdoor ANT orientation/location. e Increase separation between outdoor and indoor ANT. e Consult your dealer or a CATV/SATV/TV/Ham radio expert for assistance. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter This is a CONSUMER Device. i BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your providers consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure , contact your provider. In Canada, BEFORE USE you must meet all requirements set out in ISED- CPC-2-1-05. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless service provider. WARNING.E911 location information may not be provided or may be inaccurate for calls served by using this device. This device may be operated ONLY in a fixed location for in-building use. Authorized Accessories List Item Name Outdoor Antenna LPA-F-78 Quantity & Accessories 1 pc and A1, A2 3D Bracket 1 set/ea. w Adaptor AD-N1FO0-06 1 pc Indoor Antenna PA-F45 1pc and B1, B2 Bracket 1 set/ea. w Adaptor AD-N1F0-06 1pc 33ft RG-06/U Coaxial Cable CL06-33F 1F 1-06 1 pc w Adaptor AD-N1F0-06 1pc 17ft RG-06/U Coaxial Cable CLO6-17F1F 1-06 1 pc w Adaptor AD-T1F0-06 1pc 11ft RG-06/U Extension Coaxial Cable CLO6-11F1F 1-06 1 pc w Adaptor AD-FOFO0-06 1pc 110VAC 5V2A DC Power Adaptor RH-050200US 1 pc Note : Z\ Use only the AC-DC Adaptor in the cell booster kit package. A non-ClearCast AC-DC Adaptor may damage the signal booster. Z\ Use only the Outdoor and Indoor ANT in the cell booster kit package. Anon-ClearCast Outdoor/Indoor ANT may cause extra problems. LN Use only the coaxial cable and/or Extension coaxial cable in the cell booster kit package. A non-ClearCast coaxial cable may cause roblems. INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER BERORE USE THIS DEVICE e Verizon Wireless:

https://www.verizon.com/solutions-and-services/accessories/register-signal-booster/

e AT&T: https://securec45.securewebsession.com/attsignalbooster.com/

e T-Mobile/Sprint/MetroPCS:

https://www.t-mobile.com/support/coverage/register-a-signal-booster e UScellular: https://www.uscellular.com/support/fcc-booster-registration Specifications ID No. FCC : 2AHY2US4G-65 IC:

Model No. US4G-65 Band Frequency Band UL (MHz) DL (MHz) B12/17 698~716 728~746 B13 776~787 746~757 BS 824~849 869~894 B4 1710~1755 2110~2155 B2/25 1850~1915 1930~1995 Maximum Gain B12/7/13/5 : 60dB, B4/2/25 : 65 dB Noise Figure 6dB RF Power Output UL (dBm) DL (dBm) Conduction (GSM, AWGN) 17~20 2 (typ.) EIRP (GSM, AWGN) 27 (max.) 7 (typ.) Power Support 110V AC Input 5V2ADC Output Connectors OUT door Antenna Port : F (F) Indoor Antenna Port : TNC (F) Size Dimension, Weight 44x80x1.3in(WxDxH) 0.7 lbs. 2 YEAR WARRANTY ClearCast warrants its products for 2 years from the date of purchase against defects in workmanship and / or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase in original , unmodified condition. The warranty does not apply to any cellphone signal Boosters determined by ClearCast to have been subjected to misuse , abuse , neglect , or mishandling that alters or damages physical or electronic properties. ClearCast shall at its option , either repair or replace the product. The returned replacement products may include refurbished ClearCast products that have been recertified to meet with product specifications.

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your providers consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20cm(8inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING.E911 location information may not be provided or may be inaccurate for calls served by using this device. This device may be operated ONL This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with enproved antennas and cables as. specified by the manufacturer. Antennas MUST be installed at least 20cm(Binches) from any person. You MUST cease operating this device immediately if requested by the FCC or alicensed wireless service provider. WARNING.E911 location information may not be provided or may be inaccurate for calls served by using this device. This device may be operated ONLY in a fixed location for in-building use. US4G-65 2AHY2US4G-65 Model: US4G-65 FCC ID: 2AHY2US4G-65

See ee or eb BG eS ee ee a ee ee ee Serene ent CELLPHONE SIGNAL BOOSTER 7.4 in Romar Tectonaticgy Co. , Lid

(clearcast lou e HELPFUL FOR COVERAGE DIY KIT LOWOP OSCILLATION UALAM HEALT UP To Sooo BAST POINSLALL ALLARM INDICATION

, ee 10.3 in

= 4 COMPLETE 5 BAND CELLPHONE SIGNAL BOOSTER Romancell Technology Co. Lid

(learcast lig c HELPFUL FOR COVERAGE DIY KIT LOOP OSCILLATION HUMAN HEALTH UP TO 5000 FE EASY TO INSTALL ALARM INDICATION. Key Features ig)

("A Suspororalcoriein complete Sond CD = Cite rer rea by eecodicted catpnere prs mame Co Caorcke rctig data porto mance ClearCast jensen@clearcast biz httpuwww.clearcast biz TEL +8863 3160842 FAX +286 3 3160848 4F-1,No.842, Jingguo Ra., Taoyuan Dist, Taoyuan City 330 Taiwan Romancell Technology Co.,Ltd.

=== Cellphone Signal Booster Connection Set Up 2a

(G D)) Outdoor ANT K<e\

oo ee AG ADAPTOR I. S Ss CLG, Seon or Exizhsioh with 11f RG-O6/U Tem Nae Woset nes Guan & Assessoroe Note:

ukdoor ete PA 7 Be ad AT, A230 Bracke saan Adaptor AD-NIFO-06 1 pe Use onty me AC-OC Adaptor n he ce booster it package. Tresor Arena Paras 1 pe ad 87,82 Bracket soa, OH RE REE ie ee Astor ADIFO-6 1 pe Use ony ne otcoor ana incor ANT ne cel Dooce package. TOR RO-CIU Goma Gate (CLOSSSFIFFOG | pew Adsotor AD-NIFOOS pe Anon-Clearcat Ottoorindoor ANT may cause ex proves. T7RG05 Goal Cable (CLOSITFIF-06 | WAtapier ADTIFO-06 1p (Use ony ne costal sable andor Extension coastal cai nine et beceter it package, Tf RG-061U Exorson Coons Gabe | CLOETHFIF'-06 | 1 pow Adsptor AD-FOFO-08 pe Anen-Clearcas coal atte may caus robes. THOVAGSVZADG Poweradapior | RH-GSOZO0US [1 pe BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your providers consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20cm(8inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING.E911 location information may not be provided or may be inaccurate for calls served by using this device. This device may be operated ONLY in a fixed location for in-building use.

~~ Cellphone Signal Booster Kit Package When the users get the Cellphone Signal Booster DIY Kit, please check the default content as the Cellphone Signal Booster Kit Package shown. P# D0 Cellphone Signal Booster 11OVACSV2ADCLPARTB PAIS Wain Unt Power Adaptor Outdoor Antenna Indoor Antenna C)) |

Aoifo-00 __ ap.For000 Re Adopier RF Adar FPL) NOME)" PorExenson oe AD-TIFO-00 CLO8-2FIF1-06 CLOD-ITFIFI-06 cLos-11F1F1-00 TRF Adsgior SoReT7R RE-OGIU Coasial Cable THRRG-OBIU Extension Coaxial Cable TNCIMF(F) Specifications 16 ess Figure ra Hosea Us RF Power Ousut UL (@ony)__ BLA Band Frequeney Band UCTHFS] GLARE) | conduction (OSM, AWON)| 17-20 2008), saw aera rome [emmp(Gsu.awGn) | 27(roxs 7155) B13 reer 740757 [Power Seppo TIOVAG reat VNC Opa Bs aon at-toe [Connectors Taos Ans Pa FF]

Be rtocinss at0-2185 noo Aen Pet TNS Bans 100-015 _ 10-100 | Sine Daenaion Went [aca Tin xD aH) OTT

Romancell Technology Co.,Ltd. 4F-1, No.842, Ching-Guo Rd., Taoyuan City, Taoyuan County 330, Taiwan R.O.C. Tel: +886-33 160842 Fax: +886-33160848 Email: jensen@clearcast.biz Attestation Letter Date: 2024-01-08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(5)(i) Filing FCC ID: 2AHY2US4G-65 Romancell Technology Co.,Ltd. certifies that the equipment for which authorization is sought, is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature Contact Person: Jensen Lee Title: Manager CFR 47 2.911(d)(5)(i) Attestation Letter

Romancell Technology Co.,Ltd. 4F-1, No.842, Ching-Guo Rd., Taoyuan City, Taoyuan County 330, Taiwan R.O.C. Tel: +886-33 160842 Fax: +886-33 160848 Email: jensen@clearcast.biz Attestation Letter Date: 2024-01-08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(5)(ii) Filing FCC ID: 2AHY2US4G-65 Romancell Technology Co.,Ltd. certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signature Jensen Lee Manager CFR 47 2.911 (d)(5)(ii) Attestation Letter

Romancell Technology Co.,Ltd. 4F-1, No.842, Ching-Guo Rd., Taoyuan City, Taoyuan County 330, Taiwan R.O.C. Tel: +886-33 160842 Fax: +886-33160848 Email: jensen@clearcast.biz Attestation Letter Date: 2024-01-08 To:

FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

We, Romancell Technology Co.,Ltd., hereby. declare that the certified Complete 5 Bands Cellphone Signal Booster under FCC ID: 2AHY2US4G-65, Model number: US4G-65.Truck which is manufactured and test to ensure FCC compliance:

(1) Licensee consent for provider-specific booster has been obtained (consent be made available upon FCC/TCB request)

(2) NPS and other compliance/safeguard features have been implemented

(3) NPS and other compliance/safeguard features are defaulted to ON configuration (in operation)

(4) NPS and other compliance/safeguard features cannot be field reconfigured, disabled or removed

(5) Consumer booster is not user programmable, does not need fine tuning or adjustment, does not require professional installation

(6) Future software upgrade will not causenon-compliance Sincerely Yours, Signature:

Jensen Lee Manager

Romancell Technology Co.,Ltd. 4F-1, No.842, Ching-Guo Rd., Taoyuan City, Taoyuan County 330, Taiwan R.O.C. Tel: +886-33 160842 Fax: +886-33160848 Email: jensen@clearcast.biz FCC Authorization Date: 2024-01-08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, Romancell Technology Co.,Ltd., the undersigned, hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, some fs ope Jensen Lee Manager QA-FR-170-B 7/29/2014

Romancell Technology Co.,Ltd. 4P-1, No.842, Ching-Guo Rd., Taoyuan City, Taoyuan County 330, Taiwan R.O.C. Tel: +886-33 160842 Fax: +886-33 160848 Email: jensen@clearcast.biz FCC Confidential Authorization Date: 2024-01-08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AHY2US4G-65 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, Romancell Technology Co.,Ltd. hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description Part List/Tune up procedure The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours,

~ Signatu MZ oe Jensen Lee Manager

U.S. AGENT LETTER OF ATTESTATION Date: 2024-01-08 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(7) Filing F FCC ID2AHY2US4G-65 Romancell Technology Co.,Ltd. certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Romancell Technology Co.,Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: benjamin.kaur@iconsigh.com Signed by (printed name): Benjamin Kaur Signature:

Applicant: Romancell Technology Co.,Ltd. Address: 4F-1, No.842, Ching-Guo Rd., Taoyuan City, Taoyuan County 330, Taiwan R.O.C. FRN: 0025481250 Tel: +886-33160842 Email: jensen@clearcast.biz Signed by (printed name): Jensen Lee Signature: