Customer:
Rondish Date:
2021-03-17 Model:
WPAS-10 Type Silk Screen Art Ver.:
Art_WPAS-10_SC (20210317) Size:
Color:
Pantone 445C E a r l y A l e r t A l a r m Z o n e Early Alert Sensor Pad L o w F a l s e A l a r m Z o n e e n o Z m r a l A t r e l A y l r a E Select Pad Setting:
Secure the Pad:
1 2 3 Position the sensor pad across the bed beneath the hips of the patient. The neck of the sensor pad should exit out the side of the bed. Optional clip sets are available to prevent pad movement. They loop through the eyelets as shown below They can be clipped to the bed from to hold the sensor pad in place. Early-Alert Bed Sensor Pad WPAS-10 After 18-Month of Use CAUTION: Technology alone cannot prevent falls or injury. This device must supplement a facilitys fall management and supervisory program. Open the pocket to access the 3-way switch on the transmitter module. The default position is OFF
"TX-only" will activate Early-alert function only on the transmitter side of the sensor pad. Alarm goes o when a patient is sitting on the "TX" side edge of the sensor pad and about to leave their bed. The other side remains in a normal setting. Alarm goes o when the patient leaves their bed.
"Both-sides" will enable Early-Alert function on both sides of the sensor pad. Transmitter of the sensor pad (TX) LED TX-only Off Both-sides Built-in Transmitter (TX) Care & Maintenance Instructions:
Use disinfectant wipes or antibacterial cleansers to clean the pad Pad with Monitor:
Press the Program button on the wireless monitor unit you will hear a beeping from the monitor
(NOTE: for CordFree monitor press Program + Reset) DO NOT immerse the sensor pad in any liquid DO NOT expose the sensor pad to high temperature sanitizers Press and release the centre zone of sensor pad to add it into memory. You will see a visual and audible feedback from the monitor to conrm the signal was received Storage:
Test that the sensor pad is working by pressing and releasing Always keep the sensor pad at when in storage Operating temperature: 10C ~ 40C (50F ~ 104F) Storage temperature: 0C ~ 50C (32F ~ 122F) Battery Input: 3V 2 x CR2477 Made in China 1 2 1 2 3 WPAS-10 FCC ID: WNG-WPAS-10 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Customer:
Rondish Date:
2020-12-01 Model:
WPAS-10 Type Silk Screen Size:
Color:
Black Art Ver.:
Art_WPAS-10_SC (20201201) Transmitter 55mm 15mm TX-only O Both-sides LED Select Pad Setting:
Secure the Pad:
1 2 3 Position the sensor pad across the bed beneath the hips of the patient. The neck of the sensor pad should exit out the side of the bed. Optional clip sets are available to prevent pad movement. They loop through the eyelets as shown below They can be clipped to the bed from to hold the sensor pad in place. Early-Alert Bed Sensor Pad WPAS-10 After 18-Month of Use CAUTION: Technology alone cannot prevent falls or injury. This device must supplement a facilitys fall management and supervisory program. Open the pocket to access the 3-way switch on the transmitter module. The default position is OFF
"TX-only" will activate Early-alert function only on the transmitter side of the sensor pad. Alarm goes o when a patient is sitting on the "TX" side edge of the sensor pad and about to leave their bed. The other side remains in a normal setting. Alarm goes o when the patient leaves their bed.
"Both-sides" will enable Early-Alert function on both sides of the sensor pad. Transmitter of the sensor pad (TX) LED TX-only Off Both-sides Built-in Transmitter (TX) Care & Maintenance Instructions:
Use disinfectant wipes or antibacterial cleansers to clean the pad Pad with Monitor:
Press the Program button on the wireless monitor unit you will hear a beeping from the monitor
(NOTE: for CordFree monitor press Program + Reset) DO NOT immerse the sensor pad in any liquid DO NOT expose the sensor pad to high temperature sanitizers Press and release the centre zone of sensor pad to add it into memory. You will see a visual and audible feedback from the monitor to conrm the signal was received Storage:
Test that the sensor pad is working by pressing and releasing Always keep the sensor pad at when in storage Operating temperature: 10C ~ 40C (50F ~ 104F) Storage temperature: 0C ~ 50C (32F ~ 122F) Battery Input: 3V 2 x CR2477 Made in China 1 2 1 2 3