FCC ID: WNG-ILB-21 Wireless Indication Light

Rondish Company Limited Nexus Call System User Instructions V1.7 (2nd March 2021) NEXUS CALL SYSTEM by Rondish Contents Contents ........................................................................................................................................................ 2 1. PRODUCT OVERVIEW ............................................................................................................................... 4 1.1 System Layout ................................................................................................................................. 4 1.2 Compatible Equipment .................................................................................................................. 6 1.3 General Operation .......................................................................................................................... 9 1.3.1 Nexus Behavior Table .............................................................................................................. 9 2. USER INTERFACE .................................................................................................................................... 10 2.1 Home Screen ................................................................................................................................. 10 2.2 Alarm Screen ................................................................................................................................. 11 2.2.1 Display Details ........................................................................................................................ 11 2.2.2 Admin Reset ........................................................................................................................... 12 2.2.3 Dongle Error ........................................................................................................................... 13 2.3 Device Management .................................................................................................................... 13 2.3.1 Add New Device..................................................................................................................... 13 2.3.2 Device Location ...................................................................................................................... 15 2.3.3 Delete Device ........................................................................................................................... 16 2.4 Event Log ....................................................................................................................................... 16 2.5 Settings ............................................................................................................................................ 17 2.5.1 Change Settings ..................................................................................................................... 17 2.5.2 Backup/Restore ...................................................................................................................... 18 2.5.3 Export Log ............................................................................................................................... 18 3. INSTALLING NEXUS ................................................................................................................................ 19 3.1 Call Points ...................................................................................................................................... 19 3.2 Indication Lights ............................................................................................................................ 20 3.3 Bed Monitors ................................................................................................................................. 23 3.4 Door Monitors ............................................................................................................................... 23 3.5 Wall-mounting the Panel ............................................................................................................. 24 3.6 Maintaining Nexus ........................................................................................................................ 24 3.7 Updating Nexus ............................................................................................................................ 25 P2 NEXUS CALL SYSTEM by Rondish 4. TROUBLESHOOTING .............................................................................................................................. 26 5. FCC & CE warning statements.26-27 P3 NEXUS CALL SYSTEM by Rondish 1. PRODUCT OVERVIEW Nexus is a wireless nurse call system designed for ease of programming, installation and use. This allows rapid deployment of a low-cost call system during influenza season when hospital resources are stretched, or permanent installation for a long-term care facility or hospital ward looking for a reliable call solution. Nexus works using a 10 Android tablet for the display the tablet comes with a protective folio for placement on a desk, or can be wall-mounted with the use of an optional bracket. Alternately, a TV Box running Nexus can be connected to a larger computer monitor for a more visible display. Up to three calls can be displayed on the screen, with higher priority calls automatically moved to the top of the alarm display. Alarm priority levels are Emergency, Bath, and standard Call. If more than three calls happen to be active at the same time, Nexus will display the three highest priority events, and additional calls will display as the higher priority events are reset. All events are logged with a record of event location, call type, time of trigger and duration before reset. Indication lights placed throughout the ward or building show if there is an active call in the area. Each light has an internal buzzer with adjustable volume, and can repeat the signal to the display panel to greatly extend range and improve the reliability of wireless coverage. 1.1 System Layout P4 NEXUS CALL SYSTEM by Rondish P5 NEXUS CALL SYSTEM by Rondish 1.2 Compatible Equipment Description Model 10 Android Tablet with dongle (shown) NDP-11 Image DON-30 Touch screen user interface Call, Bath, and Emergency priority levels Customizable displays Event log with location, call type and response time Includes folio for use on desktop US, EU, and UK power plugs included Receiver dongle for smaller areas (433MHz) DON-20 DON-30 MBKT-01 Wall-mount bracket for NDP-11 Receiver dongle for large areas (LoRa) Durable acrylic design Includes mounting screws Available in black or white TVB-11 TV Box for corridor displays Allows Nexus software to run on a standard computer monitor Connect with paging receiver for a large corridor display GP2009TR Paging transmitter Signals to remote displays Signals to data pagers Allows wards to transfer or escalate calls to different areas Bedhead call/reset point (shown) Call and reset buttons Double press sends Emergency call RJ10 input for NEC-12 handset (shown) Handset remove alert Replaceable CR2477 lithium batteries Includes mounting screws Low battery indication P6 WCP-11C WCP-11C NEC-12 NDP-11 NEXUS CALL SYSTEM by Rondish NEC-12 Patient handset WCP-11 Waterproof call/reset point Call button for patient access from the bed RJ10 plug connects with WCP-11C USB break connection Includes wall-mount bracket and screws Call and reset buttons Pull cord with dual triangles Includes mounting screws Replaceable CR2477 lithium batteries Rated IP65 Low battery alert NEC-05 Wireless patient handset Includes wall-mount bracket and screws Call and reset buttons Uses 2 x AAA alkaline batteries Low battery alert Mobile call button for active residents Anti-ligature point Man-down alert in case of falls Uses CR2477 lithium battery Rated IP65 Low battery alert call devices or WHITE for bath units Call forward function to extend range Uses 6 x C-type alkaline batteries Includes wall-mount bracket and screws Low battery alert ILB-21 Indication light with Signal Bumper Dual-color LED light shows RED for normal DMS-02 Door Sensor Triggers audible and visual alert when an at-

risk patient approaches a protected doorway Configurable with door lock to restrict access Allows caregivers to escort patients TXP-11 Patient lanyard with man-down alert P7 NEXUS CALL SYSTEM by Rondish NGM-21 Bed monitor Room controller for integrated falls management system Pause & Reset alarms Works with bed/chair/floor sensormats Uses 3 x AA alkaline batteries Low battery alert WMBP-20 CCP-01 CMAT-02 Sensorpads Triggers alarm from patient bed or chair exit. Floor mats trigger when stepped upon Paired with NGM-21 monitor Durable and long-lasting CCP-01 CMAT-02 P8 NEXUS CALL SYSTEM by Rondish 1.3 General Operation Nexus follows generally accepted principles of a nurse call system as described in the UL and HTM-08 standards. Patient calls should be reset at location by the nurse or caregiver as soon as can reasonably be achieved. Pressing a Call button on the bedhead unit triggers a Call Double pressing a wall-mount bedhead triggers an Emergency call Pressing Call on a bathroom unit triggers a Bath alarm Pressing Reset will cancel the alarm The RED segment of the indication light indicates a Call is active The WHITE segment of the indication light indicates a Bath alert is active 1.3.1 Nexus Behavior Table The table below summarizes how Nexus interprets and displays signals from various devices:

Alarm Type Display/Sound Cancel by Device WCP-11C WCP-11C NEC-12 Alarm Trigger Single press Call Double press Press button Emergency Call WCP-11 Press button Bath WCP-11 Pull cord Bath TXP-11 Press button Call TXP-11 NEC-05 Patient fall Press button Emergency Call DMS-02 Door exit Door Reset on WCP-11 Reset on WCP-11C Reset on WCP-11C Reset on WCP-11C Yellow, 10s beep intervals Red, Rapid beeping Yellow, 10s beep intervals Amber, 4s beep intervals Amber, 4s beep intervals Yellow, 10s beep intervals Red, Rapid beeping Magnetic fob on TXP-11 Yellow, 10s beep intervals Amber, 4s beep intervals Magnetic fob on TXP-11 C button on NEC-05 Reset on WCP-11 Magnetic fob on DMS-02 Press TXR-02 button Press TTEST-01 button Reset on NGM-21 or Pad return NGM-21 Bed/Chair exit Bed exit/

Chair exit Amber, 4s beep intervals P9 NEXUS CALL SYSTEM by Rondish 2. USER INTERFACE Nexus was designed with a streamlined user interface for ease of use. The app is navigated similar to how you use a smartphone, using taps and swipes for general option. A virtual keyboard will pop up when entering text or an access PIN is required. A company name can be configured to display on the home screen, and alarm displays are fully customizable according to user preferences. Nexus prioritizes alarms in three levels of importance, and there is a built-in record of events to aid management if there is an adverse event or response times are tracked over time. 2.1 Home Screen been reset. This is the default view of the application, and Nexus will return to this screen after alarms have Icons at show the Nexus screens The organization name can be configured in Settings (Section 2.5) Date and time will automatically match your device Software Version Troubleshooting - Tapping the icon brings up a QR Code Scan using a smartphone camera to download a FAQ document P10 NEXUS CALL SYSTEM by Rondish 2.2 Alarm Screen The alarm screen will pop up when any event requires a response. If you tap on this icon when no alarms are present, the screen will be greyed out, and automatically return to the Home tab after several seconds. Up to three alarms can be displayed on the screen at once, however additional active alarms are indicated by the red arrow below and can be viewed by scrolling down the screen. Alarms are ordered top to bottom by priority, with older alarms listed first. Emergency alarms display in RED, and will automatically be moved to the top of the queue. Bath alarms display in AMBER, and have higher priority than a standard call. Normal Calls display in YELLOW, and will be prioritized according to the first call received. Double arrow facing downward indicates additional calls are active 2.2.1 Display Details Includes time of the event with priority level, location, and type of alarm. When all alarms have been reset, Nexus will automatically revert to the Home Screen after several seconds. Color band this indicates the alarm priority, with a time stamp shown on the left side Emergency RED band, rapid beeping Bathroom AMBER band, 4s beep interval Standard Call YELLOW band, 10s beep interval Location 1 this is typically a room or ward number, though is fully customizable Location 2 this is typically a bed or bathroom number, though it can be left blank Call Types & Priority Emergency Priority 1 P11 NEXUS CALL SYSTEM by Rondish Man-down Bath Monitor*

Bed Chair Sensor Door Pendant Call point Cord removed AC lost Low battery Priority 1 Priority 2 Priority 2 Priority 2 Priority 2 Priority 2 Priority 2 Priority 3 Priority 3 Priority 3 Priority 3 Priority 4 P12

* A bed monitor displays when pairing the device to Nexus. During an alarm Nexus will display either a bed, chair, or floor type alarm (refer to Section 2.3.1 for details) 2.2.2 Admin Reset for the system. There may be times when an event needs to be cleared from the central display panel. This can be achieved by a long-press on the event and entering the Admin PIN that has been assigned NEXUS CALL SYSTEM by Rondish 2.2.3 Dongle Error An error message will display if the receiver dongle is removed or loses connection while Nexus is active. Your system cannot function without this receiver connected, so Nexus will prompt you to resolve this before any further action can be taken. 2.3 Device Management This tab is where you add/delete devices from Nexus, and define how each should display when an alarm is triggered. Entering this tab requires inputting a 6-digit Admin PIN to access. If you have not set a PIN the default is 123456. P13 2.3.1 Add New Device From this screen, triggering a device can have two effects:

NEXUS CALL SYSTEM by Rondish If Nexus does not already have this device in memory it will create a new entry with the 6-digit device ID, device type and notification that new hardware has been detected. The device ID will show on the grey color band at the top. This will typically match the serial label on the back of a call point. The device type icon will display on the right If Nexus already recognizes a device that is triggered while in Device Management, it will exit to the Alarm Screen as if a patient has normally triggered an alarm. This ensures the call system continues to function if a patient needs help. Bed Alarms To add a monitor for a bed or chair sensorpad, first configure a CordFree bed monitor (NGM-21) to work with Nexus. It should be set to T1 and F1 for most convenient operation (refer to Section 3.3 for more details). From the Device Management tab, press Reset on the monitor to pair it with Nexus, and then assign display details. It should appear similar to below:

Once the monitor has been paired, you can then synch either a bed or chair sensorpad with the monitor, and Nexus will display the selected location with either a Bed or Chair type alarm when the patient exits. P14 NEXUS CALL SYSTEM by Rondish Door Alarms From the Device Management tab, trigger a reset signal on the door sensor to add the device into Nexus memory. This can be done by applying a magnet over the blue dot on the side of the door sensor. (refer to Section 3.4 for additional details) 2.3.2 Device Location Tapping on the Device you have just added will bring up the screen below, prompting you to enter a Primary and Secondary location. The text you enter here will display when this device is in alarm state. Device ID usually matches the serial label on back of call point. Device Type icon Location 1 to be configured by user

(must be defined) Location 2 to be configured by user

(optional) Click OK to confirm the location details, and these will now display on the Device Management screen. If you want to change how the alarm is displayed you can just tap on the entry again to make amendments. P15 NEXUS CALL SYSTEM by Rondish 2.3.3 Delete Device If you need to remove something from memory, swipe left over the device. Nexus will prompt you to confirm or cancel the device removal 2.4 Event Log The Event Log will show the location, event type, time of initiation and duration of all events from the previous 24 hours. Alarms prior to the previous 24 hours will be stored in a data file that can be accessed by exporting and opening using Excel, or the complete log can be accessed by tapping the screen seven times. Your response time is logged as the duration between an alarm triggering and being reset. Refer to Section 2.5.2 for instruction on how to export the data log. Emergency Event Types Call Presence Visit Low battery Signal lost Acknowledge P16 NEXUS CALL SYSTEM by Rondish 2.5 Settings The Settings tab is where you will set the default name to display on the Home screen, change the Admin PIN, or export the data log. Pressing this tab requires inputting a 6-digit Admin PIN to access. If using Nexus for the first time the default code is 123456 2.5.1 Change Settings This will allow you to add a company name to display on the Home Screen or update the Admin PIN. Press the Update button to make any changes take effect. Company Name displays on Home Screen Admin PIN used to access Device Management and Settings Network Settings used if system repeaters are connected (Section 2.5.4) Network ID Channel Gateway ID Update makes changes take effect P17 NEXUS CALL SYSTEM by Rondish 2.5.2 Backup/Restore After programming your system, the settings and Event log can be saved on a USB drive. This allows the programming to be restored on a second panel if the primary unit goes down. Nexus will remind you periodically to back-up the system. 2.5.3 Export Log This will allow you to transfer the Event Log to a CSV file that is openable using MS Excel. Insert a USB storage device and tap the Export Log button. Nexus will prompt you to confirm the data export. After inserting the USB drive into a PC, the file will be stored in Android/data/Nexus/events_date. P18 NEXUS CALL SYSTEM by Rondish 3. INSTALLING NEXUS Nexus has been designed for a straightforward installation process that minimizes the time your technician will spend on site. Following these steps will have your system up and running in just a few hours:

device 1. Switch on the tablet or control box and connect the receiver dongle the application will automatically open to a splash screen displaying the version of Nexus installed on this 2. Change PIN and enter name of organization (optional) in the Settings 3. Pair devices with Nexus and define how each should display during a call refer to Section 2.3 for details of adding and renaming devices. 4. Pair devices with indication lights to extend wireless coverage (optional) 5. Mount indication lights (if used), call buttons and brackets for patient handsets 6. Mount display panel on a wall (wall mount bracket is optional) 7. Test all of the call points three times (call & reset) to ensure that signals are reliably received by the panel. Refer to the Event Log to confirm that each signal was received. Dongle Status No LED not connected properly Red LED successfully connected Green LED when receiving data 3.1 Call Points Nexus call points have minimal programming and installation required for a functional call system. Follow the steps below to configure call points:

Step 0: Insert Batteries Nexus call points come with batteries pre-

installed. You will need to change these periodically based on usage. The exception is the NEC-05 handset, which uses 2 x AAA alkaline cells. Step 1: Add to Nexus Refer to Section 2.3 for how to pair and rename a call point P19 NEXUS CALL SYSTEM by Rondish Step 2: Mounting Use the call point to mark the position of the screw holes on the wall. Drill guide holes before screwing the call point into place Step 3: Connect Handsets A similar process can be followed for the handset mounting brackets 3.2 Indication Lights Corridor lights provide a visual indication when a call is active in the area, have a buzzer with adjustable volume for audible indication, and will expand the wireless range of Nexus. Follow the below steps to configure lights with your Nexus system. Step 1: Power the light Insert 6 x C-type alkaline batteries into the ILB-

21. A lead is also provided to connect with a 12V power source if the alarm will be frequently used as a call light with multiple calls a day. In this case batteries may only last weeks or months, so connecting to a DC supply is recommended. When used as a bathroom light with infrequent calls (e.g. 1 minute per day) the batteries can last up to 1 year. Note: Standby battery life (no alarms) is more than 2 years. Step 2: Select settings Remove front lens using a 2mm flat-head screwdriver and select light settings. The dip switches control whether the ILB-11 will forward alarms to a central mo nitor unit or as a night light. The buzzer has maximum volume pf 108dB, and can be silenced Switch 1 far left: Call Forward (On/Off) Controls whether alarms from paired devices are forwarded Switch 2 left center: Signal Bump (On/Off) Controls whether signals from devices that are not paired with this light are forwarded. This setting allows use of mobile devices such as bed monitors or patient pendants that move between rooms Switch 3 right center: Group Reset (On/Off) P20 Volume Alternate Flashing Group Reset Signal Bump Call Forward NEXUS CALL SYSTEM by Rondish When ON, a reset button paired with this light will reset all active alarms associated with this light. If multiple calls are active the light will reset all alarms. When OFF, a reset button paired with this light will reset only the call from this button. If multiple calls are active the light will continue to alarm. Bath Switch 4 far right: Alternate Flashing (On/Off) When ON the two segments will alternately flash during alarm When OFF, the Red segment indicates a Call, and White indicates a Volume Dial adjustable to a maximum 108dB Step 3: Enter pairing Press the Program button on the back of the indication light. The red and white sections will both stay ON to indicate the light is ready for pairing. Step 4: Read-in wireless devices Trigger the device you want to add into memory. If the device code is accepted into memory the ILB-11 will beep three times and flash either the red or white section. The WCP-11 call/reset button will flash the white LED to confirm they are paired; other wireless devices will flash the red LED to confirm. The ILB-11 has memory capacity for 15 devices. In the event the light memory is already full, an attempt to read in another device will result in a long beep to indicate is has not been accepted. Step 5: Secure mounting plate Screw the plastic mounting plate to the wall where you will want to locate the indication light. Make sure the plate is secured before mounting the light. Step 6: Mount the light Snap the indication light onto the mounting plate. You will hear a click when the light is securely in place. Release lever P21 NEXUS CALL SYSTEM by Rondish Note: To remove light to change batteries, press the release level at the bottom of the mounting bracket and lift. Light Displays:

White bath, bed/chair/floor, motion sensor Red bedhead, pendent Flashing emergency P22 NEXUS CALL SYSTEM by Rondish 3.3 Bed Monitors Nexus supports Rondish CordFree (NGM-21) monitors for a wireless fall management solution. These are delivered pre-set for single patient use (F1/t1). Step 1: Power the Device NGM-21 monitors operate on 3 x AA alkaline batteries Step 2: Select Settings If the setting needs to be adjusted, hold Program + Pause on the NGM-21 to enter monitor settings. Use the Pause button to highlight the t-setting and use Reset to select t1, then highlight the F-setting and select either F1 or F9. F1 is suitable for single patient use where the monitor may be moved around the facility, and F9 is for multi-patient use where a single monitor will control Procedure for F1 Setting Procedure for F9 Setting Step 3: Synch devices several beds. Synch with Nexus 1. Enter Nexus Device Management Tab 2. Press Reset button on NGM-21 to transmit monitor device ID for pairing 3. Rename monitor as desired to display during alarm 4. End Synch Devices to Monitor 1. Enter programming on NGM-21 2. Trigger bed/chair/sensor device to synch with monitor 3. End Moving the Monitor 1. Enter Nexus Device Management Tab 2. Rename monitor as desired to display during alarm 3. End 1. Enter Nexus Device Management Tab 2. Activate Device #1 to transmit device ID into Nexus memory 3. Rename device as desired to display during alarm 4. Activate Devices #2-9 and rename each as required 5. End 1. Enter programming on NGM-21 2. Select display ID (this is the bed#) 3. Trigger bed/chair/sensor device to synch with monitor 4. End Moving the monitor is not recommended in F9 setting. If you must, delete all records in Nexus and re-program from the beginning Step 4: Mount Monitor Use the double-sided tape or screw the wall-mount bracket into the wall where you would like the NGM-21 to be located. The monitor can be located next to the patient bed or by the entrance to allow a caregiver to deactivate alarms while tending the patient. 3.4 Door Monitors protected area. DoorWatcher strips can be installed to provide alerts if an at-risk patient attempts to leave the Step 1: Connect DMS-02 to power supply. A 12VDC power adapter with changeable country plug is available from Rondish on request. P23 NEXUS CALL SYSTEM by Rondish Step 2: Select Settings Open the end cap of the DMS-02 to access the user interface. Hold the Mode button for ~3s until the door sensor beeps and then release the button. You will use a screwdriver to adjust a rotary dial to the desired digit, and press Mode again to input each digit. Set Door ID = select 1-15 Set Area Number select 0-7 Set Door Extension select 1-2 (only used for two strips on a double door) Set Lock Time each number represents a multiple of 5s Step 3: Add to Nexus Enter Device Management tab on Nexus. Touch a magnet to the blue dot on the DMS-02 to send a pairing signal. Select a display ID for the door. Step 4: Mount Monitor by Door Mount DMS-02 door sensor next to the door that is to be monitored. Double-sided tape is provided with the sensors. Step 5: Adjust Detection Distance a open the end cap of the DMS-02 and pull out the circuit board to expose a dial showing 0-E. To increase the detection distance , To decrease the detection distance 3.5 Wall-mounting the Panel Nexus panels can be wall-mounted through use of an optional bracket (MBKT-01). This allows placement in an easily visible location like above a nurse desk or end of a corridor. The panel will need access to a power outlet, so make sure there is access to AC nearby. 3.6 Maintaining Nexus Rondish recommends changing batteries on a regular schedule to ensure that Nexus operates at an optimum level. The expected battery life of each component will depend on actual usage the below table is given below for reference only, assuming each call lasts 1min before reset. Component 1 Call/Day 5 Calls/Day 10 Calls/Day NEC-05 WCP-11C WCP-11 ILB-21*

3+ years 3+ years 3+ years 18 months 18 months 18 months 18 months 10 months 10 months 10 months 10 months 5 months P24 NEXUS CALL SYSTEM by Rondish

*Battery life assumes volume set to silent, alarm duration is 1min each, and signal bump function turned ON. 3.7 Updating Nexus There may be updates to the Nexus app since your purchase the version number is displayed at the bottom of the Home screen. If you would like to update the software, visit www.rondish.com/nexus-upgrade and follow the instructions to access the latest version. You will be prompted to enter the email address to which your software license was issued to access this page. P25 NEXUS CALL SYSTEM by Rondish 4. TROUBLESHOOTING The below table addresses a number of possible issues with possible solutions for resolving them. Symptom No power Wireless signals not receiving / signal lost notifications Dongle not receiving -

LEDs flash but nothing happens on the screen Audible alarm not loud enough Alarms not displaying properly Unrecognized device in Management tab Forgotten PIN Other Possible Solutions Check AC input to Nexus. If the NDP-11 tablet has a drained battery, it may need to charge for 1-2 hours before being turned back on again Check that each device is properly powered Check that each device has been synched with Nexus and defined how to display refer to section 2.3 Device Management Move the device closer to the display panel if this fixes the problem you may need to install a signal repeater to improve wireless coverage Check for possible sources of interference Consider moving the Nexus tablet to a different location Disconnect and reconnect the dongle Re-start the tablet Increase volume setting this can be done on indication lights and/or the Nexus tablet Use Bluetooth to connect a wireless sounder for active alarms Make sure you have entered a primary location in the Device Management section Nexus may have received a signal from a 3rd party device while the system was being programmed. Just remove this device from memory Contact your distributor for assistance Visit YouTube/Rondish to view a product tutorial Contact your local distributor for assistance 5. FCC & CE statements Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Note: The equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. P26 NEXUS CALL SYSTEM by Rondish The individual device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) The device may not cause harmful interference, and (2) the device must accept any interference received, including interference that may cause undesired operation. RF exposure statements 1. The Transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. 2. The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Hereby, Rondish Company Ltd declares that the above radio equipment types are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.rondish.com . P27

Customer:

Rondish Date:

2020-07-22 Model:

ILB-21 Type Silk Screen Size:

Color:

Black Art Ver.:

Art_ILB-21_SC (20200722) Pantone Reflex Blue C Wireless Indication Light Model No: ILB-21 Battery input: 3V 6x C-type Alkaline FCCID : WNG-ILB-21 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Manufactured by Rondish Company Limited Unit G/H, 4/F, Block 1, Kwai Tak Industrial Ctr, 15-33 Kwai Tak St., Kwai Chung, New Territories, Hong Kong Power input DC12V 800mA Made in China Program/Reset Use 2mm at head screw driver to remove

Rondish Designs in Security / Healthcare / Communication Rondish Company Limited Unit G & H, 4/F, Block 1, Kwai Tak Ind. Ctr, 15-33 Kwai Tak St., Kwai Chung, N.T., Hong Kong Tel.: (852) 25431955 Fax: (852) 25417411 DATE: 2-Mar-2021 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: WNG-ILB-21 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name

(ie- Block Diagram, Schematics, (ie- 10. Block Diagram, 11. Schematic Operational Description) Diagram, 12. Circuit Description) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely,

(signature) r

(printed name) TERRENCE YING RONDISH COMPANY LIMITED Unit G/H, 4/F, Block 1, Kwai Tak Industrial Centre, 15-33 Kwai Tak St., Kwai Chung, N.T., Hong Kong. Tel.: (852) 2541 6685 Fax: (852) 2541 7411 Email: rcl@rondish.com Website: www.rondish.com

Rondish Designs in Security / Healthcare / Communication Rondish Company Limited Unit G & H, 4/F, Block 1, Kwai Tak Ind. Ctr, 15-33 Kwai Tak St., Kwai Chung, N.T., Hong Kong Tel.: (852) 25431955 Fax: (852) 25417411 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021-03-02 SUBJECT: FCC Application for FCCID: WNG-ILB-21 To Whom It May Concern:

We, the undersigned, hereby authorize Willa Lan at A Test Lab Techno Corp. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Willa Lan on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(Must be signed by the person that is listed on the FCC Website) Company Name: RONDISH CO. LTD Contact Person: TERRENCE YING Signature: Li

RONDISH COMPANY LIMITED Unit G/H, 4/F, Block 1, Kwai Tak Industrial Centre, 15-33 Kwai Tak St., Kwai Chung, N.T., Hong Kong. Tel.: (852) 2541 6685 Fax: (852) 2541 7411 Email: rcl@rondish.com Website: www.rondish.com

Rondish Designs in Security / Healthcare / Communication Rondish Company Limited Unit G & H, 4/F, Block 1, Kwai Tak Ind. Ctr, 15-33 Kwai Tak St., Kwai Chung, N.T., Hong Kong Tel.: (852) 25431955 Fax: (852) 25417411 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021-03-02 FCC ID: WNG-ILB-21 SUBJECT:

To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the

"accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, RONDISH CO, LTD TERRENCE YING RONDISH COMPANY LIMITED Unit G/H, 4/F, Block 1, Kwai Tak Industrial Centre, 15-33 Kwai Tak St., Kwai Chung, N.T., Hong Kong. Tel.: (852) 2541 6685 Fax: (852) 2541 7411. Email: rcl@rondish.com Website: www.rondish.com