Doc. - Ref. 219-IDC Version : April 2014 Mounting Rules
> Use proper tools and hardware.
> Mount indoors in a temperature controlled environment.
> Mount detector on frame and magnet assembly on movable opening (door, window).
> Do not exceed 20 mm (6/8) gap between detector and magnet.
> Magnet spacer must be used to match magnet height with detector to ensure correct alignment and functionality.
> Do not install product on ferromagnetic surfaces. Product Summary The Indoor Door Contact IDC 200/601/701 is a wireless door/window contact designed for use with Videofied security systems. The contact includes the following features:
> Uses 1 Duracell CR123A Lithium battery for long life.
> Dual tamper function provides detection for both wall and cover tamper.
> Transmits check-in/status signal every 8 minutes. Installation Guidelines For easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices. Install the detector and other system devices in the following order:
> Programming/RF Testing - program detector and all other devices into the control panel and test RFcommunication from each intended device location to the control panel.
> Mounting - Mount detector at the tested location. Door Mounting Holes Wall Mounting Holes Magnet Base PRODUCT INSTALLATION SHEETIndoor Door Contact IDC200/601/702 (white) / IDC 210 (brown)www.videofied.com Programming/RF Testing/Mounting summarized following provides The for device programming, testing and mounting. For complete details, refer to the control panel installation manual. 1 Loosen bottom screw and separate base from detector. steps 2 Install 1 Duracell CR123 3v Lithium battery, observing correct polarity.
*Check that the LED flashes before staying RED 3 Put control panel into programming/configuration mode. 4 Using a programmed alphanumeric keypad, proceed through menus until the display shows ADD A NEW DEVICE. 5 Press YES/OK. The display shows PRESS PROGRAM BUTTON OF DEVICE. 6 Press and release program button on detector. The detector LED flashes. Wait for keypad display to show DETECTOR (1 - 25) RECORDED. Programming Button 7 Press YES/OK. The display shows RADIO RANGE TEST?
Press YES/OK again. The detector LED starts flashing and keypad display shows TEST IN PROGRESS. 8 Take detector to its intended mounting location and make sure LED flashes continuously, indicating good communication with control panel. 9 Press YES/OK to end radio range test, then press Esc/ No. 10 The display shows AREA ASSIGNMENT AREA: 1. Press either arrow button repeatedly until desired AREA number appears, then press YES/OK. 11 The display shows PERIMETER DEVICE?
Press YES/OK or Esc/No, whichever is appropriate for this device. Note: Only contacts protecting the external access should be configured for Perimeter arming. 12 The display shows NAME + LOCATION:
Enter appropriate device name/location (up to 16 characters), then press YES/OK. The display shows the device number and name for your verification. 13 Press YES/OK. The display shows FUNCTIONAL DEVICE TEST? Press YES/OK again and verify detector operation. For example, move magnet next to detector to make LED go out, then move magnet away from detector to make LED turn on indicating detection. 14 Press YES/OK to end detection verification. 15 The display shows ENTERING A NEW DEVICE?
Repeat steps 1 - 14 for remaining detectors. 16 When finished, exit from configuration mode. 2 www.videofied.comPRODUCT INSTALLATION SHEETIndoor Door Contact IDC200/601/702 (white) / IDC 210 (brown)(EN) Security notes / (FR) Notes de scurit / (DE) Hinweise zur Sicherheit English Francais Deutsch
> Remove batteries before any maintenance!
> WARNING, there is a risk of explosion if a battery is replaced by an incorrect type!
> Observe polarity when setting up the batteries!
> Do not throw used batteries! Bring them to your installer or a collection point.
> Attention ! Il y a un risque dexplosion si lune des piles utilises est remplace par une pile de type incorrect !
> Respectez la polarit lors de la mise en place des piles !
> Ne jetez pas les piles usages !
Ramenez-les votre installateur ou un point de collecte spcialis.
> Batterien vor jeglichen Wartungsarbeiten entfernen!
> Vorsicht, es besteht Explosionsgefahr, wenn eine Batterie durch eine Batterie falschen Typs ersetzt wird!
> Achten Sie beim Einsetzen der Batterien auf die Polung!
> Entsorgen Sie Batterien nicht im normalen Haushaltsmll! Bringen Sie Ihre verbrauchten Batterien zu den ffentlichen Sammelstellen. FCC Regulatory Information for USA and CANADA FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI VideoTechnologies may void the FCC authorization to operate this equipment. FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio/TV technician for help. Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
1 2 This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1 2 fonctionnement. Lappareil ne doit pas produire de brouillage, et Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le 3 www.videofied.comPRODUCT INSTALLATION SHEETIndoor Door Contact IDC200/601/702 (white) / IDC 210 (brown) XL, XLL, Visio, XT, XV and their variants 3.0V 2.7V Lithium 1 Duracell, CR123A Up to 4 years 35 A 35 mA 20 / 20 / 29 / 41 (mm) 4 / 6 / 16 / 24 (mm) 10s 2s S2View Spread Spectrum Bidirectional RF Properties Panel Compatibility Power Requirements Nominal Voltage Low battery limit Battery Type Quantity Manufacturer and reference Battery life Current Consumption Standby Max Magnet Detection Detection axis (X1, X2, Y, Z) Initialization delay Recovery delay RF Technology Radio type Central Frequency :
Transmission Security Supervision Antenna Tamper Opening detection distance Closing detection distance 868MHz : IDC200 & (Europe, Africa, Asia) 915 MHz FHSS : IDC601 (USA, Canada, South America) 920MHz FHSS : IDC701 (Australia, South America) AES algorithm encryption Polled signal every 8 minutes Integrated Wall and cover tamper Installation / Mounting Detector Magnet One screw secures cover to base;
Two screws secure detector to mounting surface. Two screws secure magnet assembly to mounting surface. Physical Data Operating temperature Maximum relative humidity Material Magnet Dimensions Body Spacer Magnet Weight: Detector Physical Protection
-10 to +55C (14 to 131F) 75%, non-condensing Plastic: ABSULV0 Alnico 5 LxWxD 3.7 x 1 x 0.86in (95 x 25.8 x 22mm) 2.5 x 0.59 x 0.39in (64 x 15 x 10mm) 2.5 x 0.59 x 0.43in (64 x 15 x 11mm) 38g/1.4oz. without battery IP31 and IK04 Standards & Certifications 868MHz - IDC200 & IDC210 Certifications Standards CE / EN50131 / NF&A2P EN60950-1:2006+/A11:2009+/A1:2010 EN300220-1 V2.4.1 EN300220-2 V2.4.1 NF&A2P 2 boucliers suivant le rfrentiel NF324-H58 Matriels de scurit lectroniques, dtection dintrusion DETECTEUR DOUVERTURE A CONTACT Commercial Brand : Videofied IDC200 (blanc) Product reference :
Certification Number : 2123200004A0 IDC210 (brun) 2123200004B0 Standards NF EN50131-2-6:
RTC 50131-2-6:
NF EN50131-5-3:
NF EN50130-4:
NF EN50130-5:
2008 Grade 2 2011 2005 2011 2011 Classe II Certifying agency :
CNPP Cert. Route de La Chapelle Ranville CS22265 F27950 SAINT MARCEL Tel : +33(0)2.32.53.63.63 Fax: +33(0)2.32.53.64.46 Sites Internet : http://www.cnpp.com Email : certification@cnpp.com Certifying agency :
AFNOR Certification 11, rue Franois de Pressens 93571 Saint Denis La Plaine Cedex Tel : +33(0)1.41.62.80.00 Fax: +33(0)1.49.17.90.00 Sites Internet : http://www.afnor.org et http://www.marque-nf.com Email : certification@afnor.org Singapour South Africa Others Certifications Netherlands 915MHz FHSS - IDC601 Certifications 920MHz FFHS - IDC702 Certifications USA Canada Australie FCC Part 15C (FCC47 CFR Part 15) IC (RSS-210 Issue 8) C-Tick (AS-NZS4268) NCP IDA ICASA i l
. s e g o o n h c e T o e d V i I S R f o k r a m e d a r T d e r e t s i g e R e r a i r e w e V n o i t o M d n a d e fi o e d V s e g o o n h c e T o e d V l i i i I S R 3 1 0 2
. e c i t o n t u o h t i w e g n a h c o t t c e b u s s n o i t a c fi j i c e p S 4 North American Headquarters1375 Willow Lake Blvd, Suite 103Vadnais Heights, MN 55110USAE-Mail : usasales@rsivideotech.comEMEA SALES23, avenue du Gnral Leclerc92340 BOURG-LA-REINEFRANCEE-Mail : emeasales@rsivideotech.comwww.videofied.comPRODUCT INSTALLATION SHEETIndoor Door Contact IDC200/601/702 (white) / IDC 210 (brown)