Main features The ISMV 200/601/702 is a wireless, battery-powered, motion activated indoor video camera. It can also be activated by user request. Wireless technology for optimal security. Color video (lighted sites) or black & white (night vision). Infrared LED for night vision. Standard motion coverage lens. Wall and cover tamper. Powered by 3 Lithium CR123A batteries for extended autonomy. Device supervision every 8 minutes. Video capture and transmission in streaming mode on user request. Flat wall mounting holes Corner mounting holes 1 1 Only use 2 of the 4 mounting holes. or . 2 1 Installation guidelines For an easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting. Install the detector and other system devices in the following order:
> Programming / RF Testing: Program detector and all other devices into the control panel and test RF communication at each intended device location to the control panel.
> Mounting: Mount detector at the tested location. 2 2 Mounting rules
> Use proper tools and hardware.
> Mount indoors in a temperature controlled environment.
> Mount camera 2.1m from the floor.
> Respect Top and Bottom side of the Motion Viewer
> When possible, mount in a wall corner in order to aim at a complete room
> Mount detector on an outside wall, aimed at area to protect.
> Do not aim detector at windows, especially those that let in direct sunlight, or at heat sources such as lamps, fireplaces, radiators and heating vents.
> Do not aim detector at moving objects such as curtains, fans or animals.
> Do not cover the Fresnel lens. 1 ISMV STREAMING MOTIONVIEWERINSTALL SHEETDOC. - REF. 212-ISMVMODIF. DATE :NOVEMBER 2016 Programming / RF Testing / Mounting following provides summarized steps The for device programming,testing, and mounting. For complete details, refer to the control panel installation manual. 9 Press OK to end the radio range test then press ESC/NO. 10 The display shows :
1 Loosen bottom screw 1 Separate base from ISMV 2 1 2 2 Install 3 CR123A 3V batteries, observing correct polarity. 3 Enter the panel into programming/configuration mode. 4 Using a programmed alphanumeric keypad, proceed through menus until the display shows ADD A NEW DEVICE. 5 Press OK. The display shows PRESS PROGRAM BUTTON OF DEVICE. 6 Press and release the program button on the ISMV using a paper clip. The ISMV LED flashes red . 3 4 3 4 Wait for the keypad to display : CAMERA REGISTERED. 7 Press OK, the keypad displays RADIO RANGE TEST ? Press OK again. The ISMV LED starts flashing and the keypad displays TEST IN PROGRESS. 8 Move the ISMV to the intended mounting location and confirm the signal is 9/9, indicating good communication with the control panel. AREA ALLOCATION :
AREA : 1 Press either arrow button on the keypad until the desired AREA number appears, then press OK. By default all devices in area 1 will be subject to the entry and exit delays. 11 The screen displays NAME + LOCATION :
Enter an appropriate device name (up to 16 characters). The name of the device should describe its intended mounting location or zone. Press OK. The display will show the device number and name for your verification. 12 Mount the ISMV on the wall:
> Follow the mounting rules on page 1.
> Hold the ISMV base against the mounting surface and mark the appropriate mounting holes.
> Drill pilot holes and install anchors where needed.
> Place the base on mounting surface so that the pilot holes line up and secure base with appropriate screws.
> Attach camera to base and secure with screw if required. 13 Press OK. The display shows FUNCTIONAL DEVICE TEST?
Press YES again and verify IMV operation. The red LED indicates the detection field. 14 Press OK to end the detection test. 15 The display shows ADD A NEW DEVICE? Repeat steps 1-14 for remaining devices. 16 When finished, exit from configuration mode by pressing and holding the ESC/NO for 5 seconds. 2 INSTALL SHEETISMV STREAMING MOTIONVIEWER Mounting recommendations Recommended mounting height is 2,1 m. There may be a 1 m radius blind zone under the detector depending on the room size and detector installation height. Confirm the detection field using the functional device test. The ISMV is fitted with a 90 wide angle lens that allows the camera to cover the full size of the area to protect. It will reduce the blind area under the detector as well. Please mount the ISMV in an angle to optimize detection. It shall be mounted opposed to the access point or asset you need to protect. The detector should not be mounted close to a door or an access point. Such installation increase the probability of a missed intrusion. When stairs mounted, please aim the detector towards the entry or the exit of the stairwell. Detection diagram Streaming option The new ISMV MotionViewer allow the user to request a live video session. The ISMV is the first battery-powered wireless camera detector emitting on 868MHz able to provide a live video stream from its camera. The 868 MHz frequency has excellent range and allow for excellent battery-life. 3 INSTALL SHEETISMV STREAMING MOTIONVIEWER Security notes / (FR) Notes de scurit / (DE) Hinweise zur Sicherheit English Franais Deutsch Remove the batteries before any Retirez les piles avant toute opration de maintenance !
maintenance !
WARNING, there is a risk of explosion if a battery is Attention ! Il y a un risque d'explosion si la batterie replaced by an improper model !
Observe polarity when setting up the batteries!
Do not litter the batteries when they are used!
Dispose of them properly according to Lithium Metal requirements utilise est remplace par un mauvais modle !
Respectez la polarit lors de la mise en place des piles !
Batterien entfernen!
vor jeglichen Wartungsarbeiten Vorsicht, es besteht Explosionsgefahr, wenn eine falschen Models Batterie durch eine Batterie ersetzt wird!
Achten Sie beim Einsetzen der Batterien auf die Ne jetez pas les batteries usages !
Polung!
Ramenez-les votre installateur ou un point de collecte spcialis. Entsorgen Sie Batterien nicht Haushaltsmll! Bringen Sie Batterien zu den ffentlichen Sammelstellen. im normalen Ihre verbrauchten FCC Regulatory Information for USA and CANADA FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC authorization to operate this equipment. FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
>
>
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio/TV technician for help. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s) Operation is subject to the following two conditions:
1 2 This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1 2 fonctionnement.. Lappareil ne doit pas produire de brouillage, et Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le This symbol on the product or on its packaging indicates that this product should not be treated as household waste. It must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources. For more information about recycling of this product, please contact your local municipality, your waste disposal service or the company that installed the product. The EC declaration of conformity of this product is available by flashing this QR code. 4 INSTALL SHEETISMV STREAMING MOTIONVIEWER ELECTRICAL PROPERTIES Panel compatibility Streaming option DETECTION PROPERTIES Infrared detection specifications W panels Technology Without streaming option XL, XLL, XT, XV, Visio and their variants Battery Nominal voltage Low battery treshold Estimated battery life Current consumption Standby (1h average) Max RADIO PROPERTIES RF S2View technology Radio type Operating frequency 3 CR123A 3V Lithium batteries 3 V 2.7 V Up to 3 years 100 A 300 mA Spread spectrum RF bidirectional 868MHz - ISMV 200 (Europe, Africa, Asia) 915 MHz - ISMV 601 (USA, Canada, South america) 920 MHz -ISMV 702 (Australia, South america) Transmission security Supervision Radio antenna VIDEO PROPERTIES AES algorythm encryption Radio, batteries, tamper Integrated Camera Angle Sensor type Lighted video Night vision video Infrared illumination Infrared illumination distance Video Video format Framerate Resolution Video file size 90 CMOS Programmable : Color or B&W Black & white automatic infrared Automatic with 2 IR LEDs 7m H264 (MPEG if not available) 5 images per second QVGA (320x240) Up to 230 kB Type Lens Detection angle Detection range Initialization time Recovery time Tamper Tamper detection BOX Physical properties Material Environmental properties Operating temperature Max relative humidity Installation / Mounting Mounting height Wall mounting Box sealing Cover and wall tamper, electromagnetic immunity Passive-infrared DSP Dual element sensor Fresnel 90 Up to 10m 10 seconds 90 seconds ABS UL94-V0
-10/+55C 75%, without condensing 2,10 m 2 screws With screw ISMV 200 STANDARDS AND APPROVALS 868 MHz Compliant with annex IV from the R&TTE 1999/5/CE directive NF&A2P 2 boucliers suivant le rfrentiel NF324-H58 Matriels de scurit electronique, dtection dintrusion DETECTEUR DE MOUVEMENT A INFRAROUGE PASSIF Marque commerciale Rfrence produits N de certification Videofied ISMV 200 2623200010 NF EN50131-2-2 Grade 2 RTC 50131-2-2 NF EN50130-4 NF EN50130-5 Environment Class II Certification organisation :
CNPP Cert. Route de La Chapelle Ranville CS22265 F27950 SAINT MARCEL Tel : +33(0)2.32.53.63.63 Fax: +33(0)2.32.53.64.46 Sites Internet : www.cnpp.com Email : certification@cnpp.com 2008 2015 2011 2011 Certification organisation :
AFNOR Certification 11, rue Franois de Pressens 93571 Saint Denis La Plaine Cedex Tel : +33(0)1.41.62.80.00 Fax: +33(0)1.49.17.90.00 Sites Internet : www.marque-nf.com E-mail : certification@afnor.org 5 INSTALL SHEETwww.videofied.comISMV STREAMING MOTIONVIEWER