Product Summary The OMV 210/611/712 MotionViewer is a wireless, battery operated, motion activated or electrically activated outdoor camera designed for use in Videofiedsecurity systems. Powered by 4 Lithium batteries for extended battery life. 90 wide lens (by default). Provided optional lenses: vertical and horizontal curtain, long range beam (up to 18m). 4 infrared LEDs for 12m night vision. Standard detection distance (up to 12 meters). Fully weatherproof
(IP65) and temperature resistant
(-20C/+60C). Tilt sensor tamper. Transmits check-in/status signal every 8 minutes. 3 wired programmable inputs (2 supervised). 1 wired programmable output triggered on detection. Installation Guidelines For easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices. Install the detector and other system devices in the order of the following steps:
> Programming/RF Testing - program detector and all other devices into the control panel and test RF communication from each intended device location to the control panel.
> Mounting - mount detector at the tested location. Mounting
> Use proper tools and hardware.
> Mount camera between 2.5 m to 4 m height.
> The OMV MotionViewer detection distance may vary depending on weather and the detector mounting (height, tilt). The OMV is not suitable to protect an area, it needs to be used to protect an access point or any property.
> Mount detector aimed toward the spot to protect.
> In order to reduce false alarms, do not aim the detector toward vegetation, a road, or unlimited space.
> Do not cover the Fresnel lens. Use only the provided masking kit to block detection towards specific spots (trees, bushes, etc.). MB110 Mounting kit for Outdoor MotionViewer 1 DOC. - REF. 213-OMVVERSION : JULY 2015INSTALL SHEETOMV OUTDOOR MOTION VIEWER Programming/RF Testing/Mounting Put panel control Separate the base from the box Install 3 3.6V LS14500 SAFT The following provides summarized steps for device programming, testing, and mounting. For complete details, refer to the control panel installation manual. 1 2 batteries observing correct polarity. 3 Programming/Configuration mode. 4 Using programmed proceed alphanumeric through menus until the display shows ADD A NEW DEVICE. 5 DEVICE. 6 the OMV MotionViewer. Press OK/YES. the display shows PRESS PROGRAM BUTTON OF Press and release program button on a keypad, Screw into The OMV PIR flashes. 7 Wait for keypad display to show CAMERA(1 - 25) PROGRAMMED. Press OK/YES, the display shows RADIO RANGE TEST? Press OK/YES again. The camera LED starts flashing and keypad display shows RF TEST. 8 Take the OMV camera to its intended mounting location and make sure LED flashes continuously or you receive a 9/9 indicating good communication with the control panel. IN IT button Press OK/YES to end radio range test then press ESC/NO. 9 10 The keypad displays :
AREA ALLOCATION :
AREA : 1 Press either arrow button repeatedly until desired area number appear then press OK/YES. By default all devices in Area 1 are automatically delayed. 11 The display shows NAME + LOCATION:
Enter appropriate device name/location (up to 16 characters), then press OK/YES. The display shows the device number and name for your verification. 12 Mount the DCV on the wall or the MB 110 Mounting kit. Follow the installation guidelines shown in page 1. 13 Press OK/YES. The display shows FUNCTIONAL DEVICE TEST?
Press OK/YES and verify camera operation. For example, wave your hand in front of the sensor to activate its LED indicating detection. 14 Press OK/YES to end detection verification. 15 The display shows OPERATION COMPLETED or ADD A NEW DEVICE? Press YES/OK. Repeat steps 1 14 for remaining cameras. 16 When finished, exit from configuration mode. 2 INSTALL SHEETOMV OUTDOOR MOTION VIEWER Mounting Recommendations For optimal use, OMV MotionViewer mounting shall respect the following recommendations. Mounting height :
Recommended mounting height should be comprised between 2.5m and 3m. When you install the MotionViewer higher, the detection distance is raised. However the sensitivity is reduced and the blind area under the MotionViewer is larger. When you install the MotionViewer lower, the sensitivity is raised and the blind area under the detector is reduced. However the detection distance will be reduced. Tilt :
The detector should be tilted 3 to 5 Raising or reducing the tilt, even slightly, has a big impact on the detection distance and on the blind area under the MotionViewer. Example : Increasing the tilt from 5 to 15 can reduce the detection distance up to 33%, that could translate into a loss of detection distance to 4 meters Blind Area Max detection distance 3 INSTALL SHEETOMV OUTDOOR MOTION VIEWER Security notes / (FR) Notes de scurit / (DE) Hinweise zur Sicherheit English Franais Deutsch Remove the batteries before any Retirez les piles avant toute opration de maintenance !
maintenance !
WARNING, there is a risk of explosion if a battery Attention ! Il y a un risque d'explosion si la batterie is replaced by an improper model !
Observe polarity when setting up the batteries!
Do not litter the batteries when they are used!
Dispose of it properly according to Lithium Metal requirements utilise est remplace par un mauvais modle !
Respectez la polarit lors de la mise en place des piles !
Batterien entfernen!
vor jeglichen Wartungsarbeiten Vorsicht, es besteht Explosionsgefahr, wenn eine Batterie durch eine Batterie falschen Models ersetzt wird!
Achten Sie beim Einsetzen der Batterien auf die Ne jetez pas les batteries usages !
Polung!
Ramenez-les votre installateur ou un point de collecte spcialis. Entsorgen Sie Batterien nicht im normalen Haushaltsmll! Bringen Sie Ihre verbrauchten Batterien zu den ffentlichen Sammelstellen. FCC Regulatory Information for USA and CANADA FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC authorization to operate this equipment. FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
>
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
1 2 This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la Partie 15 des rglementations de la FCC et avec la norme RSS-210 de lIndustrie Canadienne. Son fonctionnement est soumis aux deux conditions suivantes :
1 Cet appareil ne doit pas causer dinterfrences nuisibles et 2 Cet appareil doit accepter toute interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. 4 INSTALL SHEETOMV OUTDOOR MOTION VIEWER ELECTRICAL PROPERTIES DETECTION PROPERTIES Panel compatibility W, XL, XT, XV and their variants Infrared detection specifications Power requirements Type C - 4 Lithium batteries 3,6 V LS14500 Technology Type Detection lens Passive infrared DSP Dual element sensor 4 years 2 years 90 on 12m max (by default) 80 cm curtain for 12m distance (vertical or horizontal) 1m diameter beam for 18m distance (long distance beam) Battery life Standard usage (up to 5 videos per month) High usage (about 30 videos per month) RADIO PROPERTIES RF S2View technology Radio type Operating frequency Transmission security Supervision Radio antenna VIDEO PROPERTIES Spread spectrum bidirectionnal 868MHz - OMVC 210 (Europe, Africa, Asia) 915 MHz - OMVC 6111 (USA, Canada, South America) 920 MHz - OMVC 712 (Australia, South America) AES encryption algorithm Radio, batteries, tamper, position Environmental data Integrated Operating temperature Camera Angle Sensor type Daylight video Night video Infrared illumination Infrared illumination distance Video Video format Frame rate Video duration Video resolution Quality Average video file size Image Format Resolution Quality Average image file size 90 CMOS Programmable : Color or B&W Automatic black & white infrared Automatic with 4 IR LEDs Up to 12m MJPEG-WMV, MJPEG-DIFF 5 images per second Programmable (10 seconds by default) QVGA (320x240) SQ or HQ 220 kb JPEG VGA (640x480) HQ or SQ 8 kb Tamper detection Tilt BOX Physical properties Material Dimensions Weight Max. relative humidity Protection marking Installation / Mounting Mounting height Mounting angle Mounting Position change, shock, wall and cover tamper Polycarbonate UL94 130,5mm x 102,44mm x 141,5mm 261g (without batteries)
-20/+60C 95%, without condensing IP 65 2.5m to 4m 5 to 10 Use mounting kit (sold separately) STANDARDS AND CERTIFICATIONS EN50131-4 NF EN50131-4 NF EN50130-4 NF EN50130-5 Grade 2 -- Type W 2009 Grade 2 -- Type W 2011 2011 Environment class II Matriels de scurit electronique, dtection dintrusion DISPOSITIF DALARME SONORE Marque commerciale Rfrence produits N de certification Videofied OMVC 210 Organisme certificateur :
CNPP Cert. Route de La Chapelle Ranville CS22265 F27950 SAINT MARCEL Tel : +33(0)2.32.53.63.63 Fax: +33(0)2.32.53.64.46 Sites Internet : http://www.cnpp.com Email : certification@cnpp.com Organisme certificateur :
AFNOR Certification 11, rue Franois de Pressens 93571 Saint Denis La Plaine Cedex Tel : +33(0)1.41.62.80.00 Fax: +33(0)1.49.17.90.00 Sites Internet : http://www.afnor.org et http://www.marque-nf.com E-mail : certification@afnor.org 5 www.videofied.comINSTALL SHEETOMV OUTDOOR MOTION VIEWER