ZoneFlex 7372-E 802.11n Multimedia Wi-Fi Access Point Quick Setup Guide This Quick Setup Guide provides step-by-step instructions on how to set up your Ruckus Wireless ZoneFlex Access Point. After completing the steps described in this Guide, you will be able to place the Access Point (AP) at your site and provide wireless network access to users. BEFORE YOU BEGIN Before deploying Ruckus Wireless products, please check for the latest software and the release documentation. User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents. Software Upgrades are available at http://support.ruckuswireless.com/software.
Open Source information is available at
http://opensource.ruckuswireless.com. Software License and Limited Warranty available at http://support.ruckuswireless.com/warranty.
An 802.3af or 802.3at -compliant Power over Ethernet (PoE) switch or PoE injector IMPORTANT!
If the AP is deployed with a ZoneDirector, follow the ZoneDirector Quick Setup Guide, and connect the AP to your local network. STEP 1: CONNECT THE AP TO YOUR COMPUTER 1 After removing your Ruckus Wireless AP from its package, place it next to your computer. 2 Using an Ethernet cable, connect your computers network port to the 10/100/1000 port on the AP. 3 Using the AC adapter (sold separately), connect the AP to a convenient (and protected) power source.
Alternatively, connect the 10/100/1000 port to a PoE injector or PoE switch for both power and network con-
nectivity. ZoneFlex 7372-E Access Point PACKAGE CONTENTS
Mounting screws and anchors (2)
Declaration of Conformity (country-dependent)
Product Warranty Statement This Quick Setup Guide Security screw (1) Regulatory flyer 4 Verify that the Power LED on the external enclosure is a steady green. SETUP REQUIREMENTS
A computer running Windows 7 (procedures for other OSs are similar)
One or more of the following:
A modem (DSL or cable), broadband router, or other device provided by your Internet Service Provider that brings Internet access to your site.
A network switch or a DSL/Internet gateway device. Two Ethernet cables (Cat5e or better for PoE in)
An AC power adapter (sold separately), or Copyright 2013 Ruckus Wireless, Inc. Published March 2013, Part Number 800-70494-001 STEP 2: PREPARE YOUR COMPUTER FOR AP SETUP NOTE:
The following procedures assume Windows 7 as the operating system. Procedures for other OSs are similar. 1 On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as follows:
Start > Control Panel > Network and Sharing Center > Change Adapter Settings 2 Edit the TCP/IPv4 address settings as follows:
Local Area Connection > Properties > Internet Protocol Version 4 (TCP/IPv4) > Properties The TCP/IPv4 Properties dialog box appears. IMPORTANT!
Write down all of the currently active settings so you can restore your computer to its current configuration later (when this process is complete). 3 Select Use the following IP address (if it is not already selected) and then make the following entries:
IP address: 192.168.0.22 (or any address in the 192.168.0.x network) Subnet mask: 255.255.255.0
Default gateway: 192.168.0.1 Leave the DNS server fields empty. 4 Click OK to save your changes. Your changes are put into effect immediately. STEP 3: LOG INTO THE AP As specified earlier, the AP should be directly connected to your computer (through the Ethernet port) and powered on, ready for setup. 1 On your computer, open a Web browser window. 2 In the browser, type this URL to connect to the AP:
https://192.168.0.1 3 Press <Enter> to initiate the connection. When a security alert dialog box appears, click OK/Yes to proceed. 4 When the Ruckus Wireless Admin login page appears, enter the following:
Username: super
Password: sp-admin 5 Click Login. Page 1 of 4 Default AP Settings (For Your Reference) Network Names
(SSIDs) Wireless1Wireless8 (2.4GHz radio) Wireless9Wireless16 (5GHz radio) Security (Encryption method) Disabled for each wireless interface Default Management IP Address 192.168.0.1 STEP 4: CUSTOMIZE THE WIRELESS SETTINGS 1 On the Web interface menu, click Configuration > Wire-
less (Configuration > Radio 2.4G or Configuration > Radio 5G). The Configure :: Wireless :: Common options appear. 2 Verify that the following options are active:
Channel: SmartSelect
Country Code: If you are not located in the United States, select your current country.
External Antenna: Enable the check box and enter the external antenna gain in the field provided. 3 Click Update Settings if you made any changes. 4 Click any of the eight Wireless # tabs at the top of the page. 5 In Wireless Availability, click Enabled. 6 Delete the text in the SSID field, and then type a name for your network that will help your users identify the AP in their wireless network connection application. 7 Click Update Settings to save your changes. 8 Repeat Steps 4-7 for each Wireless # interface that you want to enable. 9 Click Logout to exit the Web interface. 10 Disconnect the AP from the computer and from the current power source, and then restore your computer to its original network connection configuration. STEP 5: PLACE THE AP IN YOUR SITE 1 Move the AP to its permanent location (accessible to both AC power and network connection). 2 Use an Ethernet cable to connect the 10/100/1000 port of the AP to your network. NOTE:
If you will be using PoE, you will need a Cat5e (or better) Ethernet cable to connect the AP to the PoE injector or switch. 3 Connect the AC power adapter (or PoE power supply) to the AP, then to a convenient power source. Copyright 2013 Ruckus Wireless, Inc. Published March 2013, Part Number 800-70494-001 4 Verify that the 10/100/1000 port LED is lit. 5 Connect external antennas to the RP-SMA connectors on the 7372-E enclosure. Note that each connector is a dual-
band (2.4 GHz & 5 GHz) spatial stream.
Ruckus Wireless offers two different antenna kits as sep-
arately orderable accessories, certified for use with the 7372-E:
911-0303-VP02 (articulating direct-mount antenna pair) 911-0505-DP01 (2-stream sector antenna panel)
After a short pause to re-establish the Internet connection, you can test the AP. STEP 6: VERIFY THE INSTALLATION 1 Using any wireless-enabled computer or mobile device, search for and select the wireless network you previously configured. 2 If you can connect, open a browser and link to any public Web site. Congratulations! Your wireless network is active and ready for use.
(OPTIONAL) MOUNTING INSTRUCTIONS The ZoneFlex 7372-E can be mounted to a wall, ceiling or to a T-
bar using the supplied mounting screws or the T-bar clips built into the bottom of the AP enclosure. Mounting to a Flat Surface 1 Use this Quick Start Guide template or the alignment spacer to mark the locations for screw holes on the mounting sur-
face. Use a 5mm drill bit to drill approximately 25mm into the mounting surface. 2 Insert the anchors and mounting screws into the mounting surface, leaving approximately 0.28 (7 mm) of the screw heads protruding for the AP enclosure. The screws should be approximately 3.25 (82.6 mm) apart per the template. 3 Insert a straightened paperclip (or similar) into the hole on the side of the AP (Figure 1.), to release the locking mecha-
nism. Figure 1. Insert a paperclip into the pinhole Hold paperclip in while mounting 4 Place the AP onto the mounting screws so that the screw heads enter the mounting holes on the AP enclosure, and push the AP downward to lock in place. 5 Remove the paperclip to release the lock mechanism and secure the AP. 6 To unmount, insert a straightened paperclip into the hole on the side of the AP to unlock, then push the AP upward to release the AP enclosure from the mounting screws. Mounting to a T-Bar The ZoneFlex 7372-E provides mounting options for flush tile and recessed frame T-bars in acoustical ceiling tiles. Flush Tile 1 Orient the AP so that the T-bar is positioned between the T-
bar clips as shown in Figure 2., then rotate the AP until the third T-bar clip catches the T-bar and the latch locks the T-bar in place (Figure 3.). Figure 2. Page 2 of 4 Figure 3. Security screw hole 2 Insert the Torx-head security screw into the hole near the latch to lock in place. 3 To remove the unit, first remove the security screw, then depress the latch while rotating the AP so that the T-bar clips disengage the T-bar. FOR MORE INFORMATION You can now use the wireless network to log into the APs Web interface. Use the Web interface to review and fine-tune a wide range of AP settings. For information on how to configure the AP from the Web interface, refer to the Ruckus Wireless ZoneFlex Indoor Access Point User Guide or the Online Help, available from within the Web interface. Copyright 2013 Ruckus Wireless, Inc. Published March 2013, Part Number 800-70494-001 Page 3 of 4 Mounting template Copyright 2013 Ruckus Wireless, Inc. Published March 2013, Part Number 800-70494-001 Page 4 of 4 Page 1 Federal Communications Commission Notices This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this equipment. For Class B Equipment:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. For Class A Equipment:
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Industry Canada Statement Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal
(ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. Le dispositif de fonctionnement dans la bande 5150-5250 MHz est rserv une utilisation en intrieur pour rduire le risque d'interfrences nuisibles la co-canal systmes mobiles par satellite, le gain d'antenne maximal autoris pour les appareils dans les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la pire limite, et le gain d'antenne maximal autoris pour les appareils dans la bande 5725-5825 MHz doivent tre conformes avec le pire limites spcifies point--ponctuelles et non point--point de fonctionnement selon qu'il convient. Operation in the 5600-5650 MHz band is not allowed in Canada. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Opration dans la bande 5600-5650 MHz n'est pas autorise au Canada. Haute puissance radars sont dsigns comme utilisateurs principaux (c.--
utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer des interfrences et / ou des dommages dispositifs LAN-EL. Radiation Exposure Statement The device has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091 and Industry Canada RSS-102 for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Le dispositif a t jug conforme aux exigences nonces dans les articles 47 CFR 2.1091 et Industrie Canada RSS-102 pour un environnement non contrl. L'antenne (s) utilise pour ce transmetteur doit tre install pour fournir une distance de sparation d'au moins 20 cm de toutes les personnes et ne doit pas tre co-localiss ou fonctionner en conjonction avec une autre antenne ou transmetteur. Mexico Statement La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Professionally Installed Products The product is to be installed according to the installation instructions. The Use/Operator does not have access to the device once the device is installed and in use. Provisions for permanent grounding is provided. 1. Installation personal: This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule Page 2 knowledge. The general user shall not attempt to install or change the setting. 2. Installation location: The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. Additionally, installation locations with 35km of Terminal Doppler Weather Radar locations shall follow instructions below. a. Any installation of either a master or a client device within 35 km of a TDWR location shall be separated by at least 30 MHz center-to-
center) from the TDWR operating frequency. b. A voluntary WISPA sponsored database has been developed that allows operators and installers to register the location information of the UNII devices operating outdoors in the 5470 5725 MHz band within 35 km of any TDWR location (see http://www.spectrumbridge.com/udia/home.aspx ). This database may be used by government agencies in order to expedite resolution of any interference to TDWRs. c. Addition information can be obtained from the FCC Knowledge Database, Publication Number 443999. https://apps.fcc.gov/oetcf/kdb/index.cfm 3. External antenna: Use only the antennas which have been approved by Ruckus Wireless. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited. 4. Installation procedure: Please refer to users manual for the detail. 5. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in US Rule CFR 47 part 15 section 15.247 & 15.407. The violation of the rule could lead to serious federal penalty. External Antenna Notice This radio transmitter has been approved by the FCC and Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Model: ZF7762, ZF7762-S, ZF7762-T, ZF7762-AC, ZF7762-S-AC: This device has been designed to operate with an omni-directional antenna having maximum gain of 6dBi or a patch antenna having a maximum gain of 23 dBi. Other antenna types or having greater gain are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Model: ZF7782 [ZoneFlex 7782, ZoneFlex 7782-S, ZoneFlex 7782-N, ZoneFlex 7782-E], Model: ZF7781CM [ZoneFlex 7781CM, ZoneFlex 7781CM-
S, ZoneFlex 7781CM-E] and Model ZF7781FN [ZoneFlex 7781FN, ZoneFlex 7781FN-S, ZoneFlex7781FN-E ]: This device has been designed to operate with an omni-directional antenna having maximum gain of 5.5dBi, Sector and Patch external antennas with a maximum gain of 15dBi. Other antenna types or having greater gain are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Model: SC8800 [SmartCell 8800; SmartCell 8800-S]: This device has been designed to operate with sector antenna having a maximum gain of 8 dBi for US and Canada. For Europe, the device can be operated with an omni-directional antenna having maximum gain of 5.5dBi, Sector and Patch external antennas with a maximum gain of 24dBi. Other antenna types or having greater gain are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Model: ZoneFlex 7441 [ZF7441]: This device has been designed to operate with an antenna having maximum gain of 2dBi. Other antenna types or having greater gain are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Model: ZoneFlex 7372E [ZF7372E]: This device has been designed to operate with an antenna having maximum gain of 7dBi. Other antenna types or having greater gain are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Products intended to be powered by an external power supply:
Caution This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked Class 2 or LPS (sub-clause 2.5 of standard EN 60950-
1). Available Ruckus power supplies intended for product operation are identified in the product datasheet. The last two digits of the power supply part number represent the country code. For additional applicable power supplies/options, see user instructions and product datasheet. Australia Statement This device complies with the ACMA requirements for a Wi-Fi device namely Radio Communications (Low Impact Potential Devices) Class Licence 2000 Amd. 1:2007 and Radiocommunications (Compliance Labelling Electromagnetic Radiation) Notice 2003. The equipment complies with the ACMA requirements for radiation exposure for a "general user/non-aware user". This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This equipment complies with the Australian safety requirements and should only used with the specified power adapter according to the product datasheet. Brazil Statement For Brazil, those products are designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. Regarding the operation on range of 5150 MHz to 5350 MHz , the average output power of the equipments must be adjusted to the maximum limit of - 0,48 dBm and for 5470 MHz to 5725 MHz, the average output power of the equipments must be adjusted to the maximum limit of 6,44 dBm Para o Brasil, esses produtos so projetados para aplicaes especficas e necessidades a serem instalados por um pessoal qualificado que tenha conhecimento regra RF e afins.Em relao operao em srie de 5150 MHz a 5350 MHz, a potncia mdia de sada dos equipamentos deve ser ajustado para o limite mximo de - 0,48 dBm e para 5470 MHz a 5725 MHz, a potncia mdia de sada dos equipamentos deve ser ajustada ao limite mximo de 6,44 dBm Page 3 The frequency band 5250 5350 MHz is restricted to indoor use. Taiwan Statement 5.25-5.35 GHzUNII,
. The control, adjustment and on/off operation of this device does not violate the Administrative regulations on low power radio waves radiated devices. Any adjustments to the device should be carried out or be monitored by a specialist who has expertise on radio frequency devices. Replacement of components which may lead to the violation to the regulations is not allowed. Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to an approved low power radio-frequency devices. The low power radio-frequency device shall not influence aircraft security and interfere with legal communications; if found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must not be susceptible with the interference from legal communications or ISM radio wave radiated devices. European Union Notices and National Restrictions Italy This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless operating within the boundaries of the owners property, the use of this 2.4 GHz Wireless LAN product requires a general authorization. Please check with http://www.comunicazioni.it/ for more details. Questo prodotto conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato allinterno del proprio fondo, lutilizzo di prodotti Wireless LAN a 2.4 GHz richiede una "Autorizzazione Generale". Consultare http://www.comunicazioni.it/ per maggiori dettagli. Belgium The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Please check http://www.bipt.be for more details. / Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie http://www.bipt.be voor meer gegevens. /
Les liaisons sans fil pour une utilisation en extrieur dune distance suprieure 300 mtres doivent tre notifies lInstitut Belge des services Postaux et des Tlcommunications (IBPT). Visitez http://www.ibpt.be pour de plus amples dtails. EU Declaration of Conformity This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):
Ruckus Wireless, Inc. 350 West Java Drive Sunnyvale, CA 94089 The object of the declaration is in conformity with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (*):
The object of the declaration is in conformity with Directive of 9 March 1999 of the European Parliament and of the Council on Radio Equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity. The following standards were applied during the assessment of the product:
Radio: ETSI EN 300 328, ETSI EN 301 893, ETSI EN 302 502 EMC: EN 55022, EN 301 489-1, EN 301 489-17 Safety: EN 60950, EN 62311 The frequency band 5150 5350 MHz is restricted to indoor use. The frequency band 5745 5875 MHz are non-harmonized frequencies. Use is restricted to outdoor professionally installed access points as allowed by local authorities. esky
[Czech]
Dansk
[Danish]
Deutsch
[German]
Eesti
[Estonian]
English Espaol
[Spanish]
Ruckus Wireless tmto prohlauje, e tento Radio LAN je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Undertegnede Ruckus Wireless erklrer herved, at flgende udstyr Radio LAN overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt Ruckus Wireless, dass sich das Gert Radio LAN in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Kesolevaga kinnitab Ruckus Wireless seadme Radio LAN vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Hereby, Ruckus Wireless declares that this Radio LAN is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por medio de la presente Ruckus Wireless declara que el Radio LAN cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ruckus Wireless Radio LAN Page 4
[Greek]
Franais
[French]
Italiano
[Italian]
Latviski
[Latvian]
Lietuvi
[Lithuanian]
Nederlands
[Dutch]
Malti
[Maltese]
Magyar
[Hungarian]
Polski
[Polish]
1999/5/. Par la prsente Ruckus Wireless dclare que l'appareil Radio LAN est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Con la presente Ruckus Wireless dichiara che questo Radio LAN conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o Ruckus Wireless deklar, ka Radio LAN atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo Ruckus Wireless deklaruoja, kad is Radio LAN atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart Ruckus Wireless dat het toestel Radio LAN in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hawnhekk, Ruckus Wireless, jiddikjara li dan Radio LAN jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Alulrott, Ruckus Wireless nyilatkozom, hogy a Radio LAN megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Niniejszym Ruckus Wireless owiadcza, e Radio LAN jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus
[Portuguese]
Ruckus Wireless declara que este Radio LAN est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Slovensko
[Slovenian]
Slovensky
[Slovak]
Suomi
[Finnish]
Svenska
[Swedish]
slenska
[Icelandic]
Norsk
[Norwegian]
Ruckus Wireless izjavlja, da je ta Radio LAN v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Ruckus Wireless tmto vyhlasuje, e Radio LAN spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. Ruckus Wireless vakuuttaa tten ett Radio LAN tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hrmed intygar Ruckus Wireless att denna Radio LAN str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Hr me lsir Ruckus Wireless yfir v a Radio LAN er samrmi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 1999/5/EC. Ruckus Wireless erklrer herved at utstyret Radio LAN er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999/5/EF. D
-
1 0 0
-
2 0 4 0 7
-
0 0 8