Packing List Scenario 1: Configure one router to access the Internet Access the Internet by App Download the Reyee Router App Reyee RG-R6 Mesh Router User Manual Scan to Download Reyee Router App Name Router Power Adapter Warranty Card User Manual Network Cable Quantity 1 1 1 1 1 Unit Set Piece Copy Copy Piece Product Appearance Reset button Power port WAN port LAN1-2 port Reyee Mesh indicator Status Blinking white Description The device is being paired. Four bars are steady white The signal of Reyee Mesh is excellent. Three bars are steady white The signal of Reyee Mesh is good. Two bars are steady white The signal of Reyee Mesh is average. One bars is steady white The signal of Reyee Mesh is poor. Off Reyee Mesh is disconnected or not used. System status indicator (Around One-click Reyee Mesh button) Status Description Steady blue The device is normally working and can access the Internet. Steady orange The device cannot access the Internet. Blinking blue The device starts up/is restoring the factory settings. Scenario 1: Congure one router to access the Internet 1. Connect the power cord and network cable. e m d I S P M o Power Register an account by one click Tap Add Router and follow the guide for configuration Login/Register 3200M Wi-Fi 6 Dual-band Mesh Router Model: RG-R6 Power: 12V 2.5A SSID :
Default Management Address: 192.168.110.1 Version: V1.00 S/N: G1XXXXXXXXXXX MAC: XXXXXXXXXXXX CAN ICES-003 (B)/NMB-003(B) FCC ID:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation. IC:
Download Reyee Router https://www.ireyee.com/support XXXX is the last 4 digits of MAC address on the lable of router. The router will detect the Internet access method automatically. You can configure the parameters based on your requirements. 2. Configure the Router. The router will start up in about 2 to 3 minutes. Wait until the system status indicator is steady on and the SSID is broadcast (default SSID: @Reyee-sXXXX). Access the Internet by Web browser Connect to the SSID @Reyee-sXXXX (XXXX is the last 4 digits of MAC address) by mobile phone. The configuration page will be displayed automatically, or you can visit 192.168.110.1 by browser. Add Router The SSID/password configuration takes effect in 2 to 3 minutes. After the new SSID is display in the Wi-Fi list, connect to the SSID and you can access the Internet. 3200M Wi-Fi 6 Dual-band Mesh Router Model: RG-R6 Power: 12V 2.5A SSID :
Default Management Address: 192.168.110.1 Version: V1.00 S/N: G1XXXXXXXXXXX MAC: XXXXXXXXXXXX CAN ICES-003 (B)/NMB-003(B) FCC ID:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation. IC:
Download Reyee Router https://www.ireyee.com/support XXXX is the last 4 digits of MAC address on the lable of router. Scenario 2: Configure more router to form whole family Mesh network To cover every corner of a villa, large house or condo, you can buy multiple Reyee Mesh routers to form a wireless mesh network solution for full-house coverage. 1. Connect the master router (any new one) to the Internet Please refer to the Scenario 1 for configuration. 2. Put the rest of Reyee routers within 2 meters of the master router and power it on Wait for 2 to 3 minutes until indicators in each device turn to steady on. 3. Press the Reyee Mesh button on the master router for pairing When the Reyee Mesh indicator of master router blinks, it searches for neighboring devices. When the Reyee Mesh indicator of the rest of devices blinks, it means that two routers are being paired. After 2 minutes, the indicators change to steady white, and the pairing completes. Reyee Mesh Button 4. Move the paired devices to the position where the signal needs to be expanded, and then power it on again Wait for 3 to 5 minutes until the indicator turns to steady on, the original SSID of secondary router(@Reyee-sXXXX) will disappear and the united SSID/password will be the one you just configured. The connection is successful, whole house mesh Wi-Fi setting done. Please properly place the routers and check the signal bar if needed. Do not place two routers too far away and avoid too many walls or other obstacles. If you have 3 or more routers, you can pair them by one-click Reyee Mesh during startup, or repeat the step 2 to step 4 according to your requirements. At most 5 routers (4+1) can be paired as recommendation. FAQs What to do if I forget the management password?
Try the Wi-Fi password which may be the same with the management password. If not, please restore the factory settings. How to restore the factory settings?
Power on the router and wait for 2 to 3 minutes until it starts up. Press the Reset button for more than 3 seconds until the system status indicator blinks. After the indicator changes to steady on and the SSID @ Reyee-sXXXX is broadcast, the router restores the factory settings successfully. Can I connect multiple routers with network cables?
Yes, and wired connection is more stable. You can connect the WAN port (yellow) from secondary device with the LAN port (black) from master router for wired connection. Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Statement:
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. RF Exposure Warning!
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANT!
Operation in the band 5150-5250 MHz is only for indoor use. Innovation,Science and Economic Development Canada Statement This device complies with Industry Canadas licenceexempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage;
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. including interference that may cause Exposure Statement The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 et la conformit l'exposition de RSS 102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformit de rf. RF Exposure Warning!
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet metteur ne doit pas tre Coplac ou ne fonctionnant en mme temps qu'aucune autre antenne ou metteur. Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre le radiateur et votre corps. 5G Statement 1. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2.DFS (Dynamic Frequency Selection) products that operate in the bands 5250-5350 MHz, 5470-5600MHz, and 5650-5725MHz. 1. Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
2.Les produits utilisant la technique dattnuation DFS (slection dynamique des frquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.