Device layout USER MANUAL Control Easy to use by 3 way:
Fingerprint. Mobile App. 3 touch. Stored & shared Clever lock has a capacitive fingerprint sensor. You can add up to 32 fingerprints data. Share the user account with total 4 account. The following suggestions will help your device working better:
Make sure your finger is clean and not wet. Put your finger full covered on the fingerprint sensor. You can rotate and put your fingers with 360 rotation. Ownership Easy to registration your ownership by the email. Install the application Clever application is management software of the Clever lock with standard-based communication via Bluetooth 4.0 Choose your Clever When the user start the application. The Clever application's scanning interface is the first user interface. After that, touch on the fingerprint sensor of Clever Lock and tap to connect your lock on the mobile app. Charging the battery Before using the device for the first time, you must charge the battery. Charge your device using the performance charger (DC: 5V -
1A). You can also charge your device using a USB cable connected to a computer, but charging might take longer. Hold the cable with the facing up, and connect the cable into the function port on your device. Plug the charger into a power outlet. Keeping your battery charged Your Clever device uses a lithium polymer battery. To maximize your use the battery, when possible, do the following:
Avoid using the device while charging to help it recharge faster. hot or cold places. Avoid charging, using, or storing your device in extremely Should charge your Clever every 3 months. Avoid your device is turned off in low battery condition for a long time. LED status indicator The following table shows what the LED status indicators are for and what the different colors or flashing of the lights mean. LED color Status No light Green Red Yellow Solid Pulse Solid Flashing (one flash per five seconds) Fast Flashing Solid Description Clever is in sleep mode. The battery in Clever is at 0%
(connect to a power source via USB to charge). Unlock completed. Clever is connected to power source and is charging. When the charging is full, the LED will turn off to save energy. Lock completed. Battery level of Clever is under 30%. Fingerprint data processing. Clever is busy. Notice 2015 Rynan Technologies Pte Ltd. All rights reserved. FCC Statement:
the interference Federal Communication Commission Interference Statement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. The contents of this user guide and the specifications of the products are subject to change without notice. RYNAN TECHNOLOGIES reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) cause by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication. IC Statement:
This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. IMPORTANT NOTE: IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Safety information Read all safety information before using the device to ensure safe and proper use. Warning Do not expose the device to damage. Use manufacturer-approved charger, accessories, and supplies. Prevent the multipurpose jack and battery terminals from contacting conductive elements, such as metal or liquids. Do not touch the charger or the device with wet hands while the device is charging. Keep your device dry. If any part of the device is cracked or broken, stop using the device immediately and take it to Service Centre. Do not allow children or animals to chew or suck the device. into the mouth. Do not poke eyes, ears with the device or insert the device The device can be used in locations with an ambient temperature of 0oC to 350C. You can store the device at an ambient temperature of -0oC to 500C. Using or storing the device outside of the recommend temperature ranges may damage the device of reduce the batterys lifespan. Do not store your device near or in heaters, microwaves, cooking equipment, or high pressure containers. Correct disposal This marking on the product, accessories or literature indicates that product and its electronic accessories (e.g.charger, USB cable) should not be disposed of with other household waste. Removing the battery To remove the battery, you must visit an authorised service centre with the providedinstructions. For your safety, you must not attempt to remove the battery. If the battery is not properly removed, it may lead to damage to the battery and device, cause personal injury, and/or result in the device being unsafe. RYNAN TECHNOLOGIES does not accept liability for any damage or loss (whether in contract or tort, including negligence) which may arise from failure to precisely follow these warnings and instructions, other than death or personal injury caused by RYNAN TECHNOLOGIESs negligence. Contact information At RYNAN Technologies, we develop innovative products that allow our customers to operate more efficiently and sustainably. We are devoted to creating the most effective and environmentally friendly solutions for the industries we serve, including coding and marking, printing, packaging, and medical. in Singapore, RYNAN Technologies Headquartered understands the needs of customers in the fast growing, dynamic markets in Asia and around the globe. RYNAN is invested in the research and development of leading edge technology to continually build on our diverse portfolio of products, which currently inkjet and Piezo inkjet variable data printers, ink solutions, and offset CTP plates includes thermal Rynan Technologies Pte Ltd 10 Kallang Avenue Aperia Tower 2, #05-10, Singapore 339510 Tel: +65 6871 8922 www.cleverlock.io www.rynantech.com info@rynantech.com