FCC ID: 2BAAG-NW0101 Network module

NW-0101 Module Datasheet Version 1.0 1. Description The NW-0101 is a highly integrated module designed by RYSE Inc.. It utilizes the Mediatek MT7688AN System on a Chip (SoC) device which is based on the MIPS 24K CPU processor core. The SoC includes 802.11b/g/n Wi-Fi, making the Omega2 ideal for Internet of Things (IoT) applications and projects. In addition to the SoC, the module includes DDR2 DRAM, Flash memory, and all of the components necessary to allow this product to be a fully functional and complete device. Mechanical dimensions and footprint: 20mm x 35mm, 2.8mm high Greater quantity of I/O signals available to the user, 42 I/O. No SD Card slot on the bottom. No Wifi chip antenna. An external antenna must be connected. 2. Key features Embedded MIPS24KEc (580 MHz) with 64 KB I-Cache and 32 KB D-Cache 1T1R 2.4 GHz with 150 Mbps PHY data rate Legacy 802.11b/g and HT 802.11n modes 20/40 MHz channel bandwidth Green AP/STA - Intelligent Clock Scaling (exclusive) - DDRII: ODT off, Self-

refresh mode 1-port 10/100 FE PHY x1 USB 2.0 Host SPI/SD-XC/eMMC SPI, I2C, I2S, PWM, PCIe, UART, GPIO An optimized PMU WEP64/128, AES, WPA, WPA2, WAPI LEDE Linux Operating System 3. Regulations 3.1. List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular. 3.2. Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-

alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 3.3. Limited module procedures Not applicable 3.4. Trace antenna designs Not applicable 3.5. RF exposure considerations To maintain compliance with FCCs RF Exposure guidelines, this equipment should be installed and operated with minimum distance of 20cm from your body. 3.6. Antennas This radio transmitter FCC ID: 2BAAG-NW0101 has been approved by FederalCommunications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna type Patch antenna Maximum Antenna gain 4.4dBi 3.7. Label and compliance information The final end product must be labeled in a visible area with the following " Contains FCC ID: 2BAAG-NW0101, IC: 30116-NW0101 3.8. Information on test modes and additional testing requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host. 3.9. Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B. 4. Block Diagram 5. Specifications 6. Pin-Out Information 6.1. PinOut Diagram 6.2. Pin Definations 7. Mechanical Drawing and Specifications ISED Important Note:

In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the ISED cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to RSS-247 and RSSGen requirement, only if the test result comply with RSS-247 and RSS-Gen requirement, then the host can be sold legally. Note Importante:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l' ISED ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. toute entreprise de l'hte qui installent ce dispositif modulaire avec limite approbation devrait effectuer l'essai des modules et des rayonnements non essentiels des missions rayonnes selon rss-247 et le cnr - gen, seulement si le rsultat d'essai conforme rss-247 et le cnr - gen, puis l'hte peut tre vendu lgalement. End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC:30116-NW0101. Plaque signaltique du produit final Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:

Contient des IC:30116-NW0101. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. This radio transmitter [30116-NW0101] has been approved by Innovation, Scienceand Economic Development Canada to operate with the antenna types listed below, It has an antenna with the maximum antenna gain is 4.4dBi Antenna type Patch antenna Maximum Antenna gain 4.4dBi Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Cet metteur radio [30116-NW0101] a t approuv par Innovation, Science et dveloppement conomique Canada pour fonctionner avec les types dantenne numrs ci-dessous.Il dispose d'une antenne avec une prise le gain maximum d'antenne est de 4.4 dBi. Antenna type Patch antenna Maximum Antenna gain 4.4dBi Les types d'antennes non inclus dans cette liste qui ont un gain suprieur au gain maximum indiqu pour tout type rpertori sont strictement interdits pour l'utilisation avec cet appareil. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co located or operating in conjunction with any other antenna

or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body. ISEDC Warning This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference,including interference that may cause undesired operation of the device. Le onjunc areil est conforme aux CNR d linnovation, la science et le dveloppement conomique Canada licables aux areils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) lareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, onj si le brouillage est susceptible den compromettre le fonctionnement. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Tous les changements ou modifications non expressment approuve par le responsible de la conformit pourrait vider lutilisateur est habilit exploiter lquipemen. ISEDC Radiation Exposure Statement:

This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limitesdexposition de rayonnement RF ISEDC tabliespour un environnement non contrl. Cetmetteur ne doit pas tre co-implant oufonctionner en onjunction avec toute autreantenne ou transmetteur. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body. La distance entre le radiateur et le corps doit tre d'au moins 20 cm lors de l'installation et du fonctionnement de l'appareil.

8 7 6 5 4 3 2 1 D C B A FCC ID: 2BAAG-NW0101 Model: NW-0101 YYWW IC:

30116-NW0101 LEGEND:

A. Logo B. Part Number: NW-0101 C. Date Code: YYWW D. MAC Address: Barcode E. FCC ID: 2BAAG-NW0101 F. IC: 30116-NW0101 G: Checksum ORIGINAL RELEASE DRAWN:

NAME:

YY/MM/DD Aras Puodziunas 23/03/15 RYSE Inc. D C B A 8 7 6 5 4 3 2 FINISH: Vendor Decide GENERAL NOTES:

UNITS: mm TO BE PRINTED IN HIGHEST RESOLUTION

*MAC ADDRESS BARCODE IS ONLY REFERENCE, REPLCAE WITH CORRECT BARCODE*

NW-0101 Label Print SIZE DWG. NO. B CAD: ILLUSTRATOR 1 SCALE:

REV 6 SHEET:

1 OF 1 5 : 1 1

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email:trungp@helloryse.com Attestation Letter Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(5)(i)(ii) Filing FCC ID: 2BAAG-NW0101 RYSE Inc. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. RYSE Inc. certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signature Contact Person: Trung Pham Title: CEO Company Name& Address:

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 CFR 47 2.911(d)(5)(i)(ii) Attestation Letter

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: trungp@helloryse.com Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, RYSE Inc., hereby authorize China Certification ICT Co., Ltd (Dongguan) to act as a laboratory for testing and test report generation for the following project(s):

(Product description: Network module, model name: NW-0101, NW-01XX, FCC ID: 2BAAG-NW0101) declare that the device does not support channel 12-13 in 2.4 GHz band and any non-US channels Sincerely Yours, Clients signature Printed Name: Trung Pham Title: CEO

FCC ID: 2BAAG-NW0101 RYSE INC. Company name: RYSE INC. Mail: charleston@helloryse.com QPDG004R32 Version1.020140717 Declaration of Alteration To Whom It May Concern, We, RYSE INC. , hereby declare that the following models are the same except the colour of external surface as well as country or/and region codes. Details are outlined as below: Products Description Name Network module Brand RYSE INC. Differences Description Testing Model Multiple Model Difference Details NW-0101NW-01XXCountry or/and region codes 1st, 2nd X denotes country or/and region codes where each X to be replaced by the digits from 0 - 9 or A - Z, which are only for marketing and internal tracking purposes Besides the differences in the table above, we declare the products are identical. We guarantee all the information provided above is true, and notice that well bear all the consequences to be caused by any false information or concealing. Best Regards. Signature: Trung PhamPrint Name: Title: CEO

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: trungp@helloryse.com Date: 2023-05-05 FCC Authorization FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We , RYSE Inc., Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Clients signature Printed Name: Trung Pham Title: CEO QA-FR-170-B

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: trungp@helloryse.com FCC Confidential Authorization Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2BAAG-NW0101 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, ( RYSE Inc. ) hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature:

Printed Name: Trung Pham Title: CEO QA-FR-171-A

RYSE Inc. Add: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 Tel: (+1) 929-219-3299 Email: trungp@helloryse.com Modular Approval Letter Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 We, RYSE Inc., hereby request Modular Approval for Product: Network module

(Model number: NW-0101, NW-01XX), FCC ID: 2BAAG-NW0101).The EUT meets all of the requirement for modular approval as detailed in FCC 15.212. the requirements is described below:

1. The modular has RF shielding, please refer to the EUT photo. 2. The modular transmitter has buffered modulation/data inputs, Buffered data inputs stage has been integrated in chip (Model:MT7688AN). 3. The modular transmitter has its own power supply regulation. Please refer to the schematic. 4. Comply with the antenna requirements of Section 15.203 and 15.204(c), themodular have a PCB type antenna connected to the module,the maximum gain is 4.4dBi. 5. The EUT was tested in a stand-alone configuration, please refer to setup photos exhibit for details. 6. The module labeled with its own FCC ID. 7. Comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The necessary explanation to be complied with this requirement is contained in the user manual, band please refers to the User Manual. 8. Comply with any applicable RF exposure requirements in its final configuration. Sincerely, Signature:

Printer Name: Trung Pham Title: CEO

U.S. AGENT LETTER OF ATTESTATION Date: 2023-05-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(7) Filing FCC ID: 2BAAG-NW0101 RYSE Inc. certifies that, as of the date of the filing of the application, RYSE USA INC. is our designated U.S. agent for service of process for the above referenced FCC ID. RYSE Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. RYSE USA INC. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Company Name: RYSE USA INC. Address: 1401 21ST St. Suite 5216, Sacramento, California, USA 95811 FRN: 0033398595 Tel.: (+1) 929-219-3299 Email: trungp@helloryse.com Signed by (printed name): Trung Pham Signature:

Applicant: RYSE Inc. Address: 20 Camden St. Suite 200, Toronto, Ontario, Canada M5V1V1 FRN: 0033405994 Tel: (+1) 929-219-3299 Email: trungp@helloryse.com Signed by (printed name): Trung Pham Signature: